Axial Wall Research Articles

Effect of Occlusal and Axial Thickness on the Fracture Load of Implant-Supported Monolithic Zirconia Crowns.

To evaluate the fracture load of monolithic zirconia crowns with implant screw holes, focusing on variations in occlusal and axial thicknesses, and to assess the interaction between these variables. Six different prostheses were designed using CAD software, varying in occlusal thickness (0.5 mm, 1.0 mm) and axial thickness (0.4 mm, 0.8 mm, 1.2 mm) based on the height and thickness differences of the titanium implant abutment. Twelve specimens per design were created by milling zirconia blocks and titanium abutments. These specimens were cemented with resin and subjected to thermomechanical aging (50 N, 200,000 cycles, 5°C-55°C, 30 seconds dwell time) using a chewing simulator. Static loading was applied using a universal testing machine at a rate of 0.5 mm/min until fracture occurred, and the load value (N) at the moment of the initial fracture was recorded. Fracture pattern and surface analyses were performed. Statistical analyses included two-way analysis of variance, Tukey HSD test, multiple regression analysis, and Fisher's exact test. Both occlusal and axial thicknesses significantly influenced the fracture load (P < .05), with a significant interaction between them (P < .05). An occlusal thickness of 1.0 mm exhibited a significantly higher fracture load compared to 0.5 mm (P < .05). An axial thickness of 1.2 mm showed a significantly higher fracture load compared to 0.4 mm and 0.8 mm (P < .05). The difference in axial thickness between 0.8 mm and 1.2 mm had a more substantial impact on fracture load than the difference in occlusal thickness between 0.5 mm and 1.0 mm (P < .05). Fractographic analysis showed that the thin axial wall exhibited twist hackles without involvement of the crown margin, whereas the thick axial wall exhibited no hackles and a more catastrophic failure involving the crown margin. For monolithic zirconia crowns with implant screw holes, when sufficient occlusal thickness cannot be achieved, an axial thickness of at least 1.2 mm is recommended to ensure higher fracture resistance.

Utilizing 3D Model and Comparison Software Tools in Improving Assessment Methods: A Pilot Study

Purpose/Objectives: This manuscript investigates the effectiveness of computer-assisted design and manufacturing (CAD/CAM) technology in preclinical dental education. The COVID-19 pandemic created a need for remote teaching approaches. In preclinical fixed prosthodontics courses, traditional evaluation methods rely on faculty to visually grade laboratory projects utilizing rubrics and 2D images. Assessment and feedback vary amongst faculty, and faculty calibration has been inconsistent in reducing intra-and inter-rater variability. This study aimed to compare faculty assessment of student full coverage crown (FCC) preparations traditionally versus digitally through 3D model visual assessment and/or comparative analysis software reports. Methods: Eighteen UTHealth Houston School of Dentistry faculty participated, each randomly assigned into one of three assessment groups: traditional visual Group (TV), 3D Group (3D), and 3D visual assessment supplemented with comparative analysis software report (3D+) Group. Faculty graded the same eight lithium disilicate typodont preparations for all three assessment groups. Results: Survey results showed the ease of use and efficiency among the three assessment methods varied significantly. Grading scores revealed that axial wall reduction significantly differed among the three assessment methods. Conclusion: This study concludes that the combination of the two digital assessment methods can overcome the limitations of traditional evaluation methods and digital methods alone by providing objective feedback to students and enhancing their learning experience.

Advancing thermohydraulic performance of micro-grooved flat heat pipes through a combined numerical-experimental approach

A combined numerical-experimental model has been developed to predict the thermohydraulic characteristics of micro-grooved flat heat pipes (FHPs). This model uses a limited number of experimental data for calibration with two parameters, βexp,1 and βexp,2, which account for uncertainties in the accommodation coefficients used to determine evaporation and condensation mass fluxes. This calibration, which is a key feature of the developed model, addresses the uncertainties and challenges in determining these coefficients. Moreover, the model incorporates the effects of interfacial shear stress, axial wall conduction, heat transfer in the liquid block region, and the contact angle of the liquid–vapor interface. Furthermore, the evaporation mass flux from the curved liquid–vapor interface is calculated using a separate multiscale approach developed in two recent works for analyzing evaporation from the extended meniscus in microchannels, considering thin-film evaporation. The model demonstrates high accuracy in predicting the maximum heat transport capacity (Qmax) and wall temperature distribution across various input heat powers, with a maximum error of less than 0.5 % in wall temperature predictions, as validated against experimental data. The validated model is then used to explore a new micro-grooved wick structure featuring converging/diverging microchannels. In this structure, the channel width is constant and equal to Wf2 in the first half of the heat pipe, from the condenser end to the midpoint, and then it decreases or increases to Wf1 by the end of the evaporator section. Results indicate that a flat heat pipe with a converging micro-grooved wick structure (Wf1 = 200 µm and Wf2 = 160 µm) can enhance Qmax from 53 to 70 W, 70.8 to 91.8 W, and 91.2 to 116.5 W at working temperatures of 60 °C, 70 °C, and 80 °C, respectively. This means the new converging micro-grooved wick structure can boost flat heat pipe performance by more than 25 % compared to a flat heat pipe with a straight micro-grooved wick (Wf1 = Wf2 = 200 µm) without increasing the occupied space.

Development of a transient analysis code for trans-critical simulation of SCWR

Supercritical water-cooled reactors (SCWR) experience pressure reductions below the critical point during a loss of coolant accident (LOCA). During the reactor depressurization, boiling crises may occur, leading to pressure fluctuations and significant increases in wall temperatures, posing a severe threat to the cladding. In this study, a one-dimensional transient analysis code has been developed to incorporate one-dimensional steady-state flow equations in the fluid domain and transient thermal conductivity equations in the solid domain. The code also includes a wall heat transfer model and a model for the velocity of the moving quench front to simulate transcritical depressurization transient processes. The simulation successfully predicts the typical experimental phenomena. It is reasonable to use the critical temperature as the demarcation point between the dry and wet conditions of the axial wall of the rod bundle under transcritical conditions. By combining the experimental data with the program calculations, the critical interface for the occurrence of boiling crisis under transcritical conditions is determined using mass flow rate, heat flow density and fluid temperature as inputs. The criterion for the occurrence of CHF under transcritical conditions is obtained, which provides a reference to the safety analysis of SCWRs.

Evaluating the Effectiveness of the "Double Finish Line Technique" on Full-Crown Retention for Short Abutments: An In Vitro Study.

Achieving clinically adequate retention for cast crowns in prepared short abutments represents a major challenge for practicing dentists. Despite the important developments with adhesive cement, only a few teeth can be treated this way, and conventional preparation techniques are still employed for most crowns. Numerous options for auxiliary features exist; however, there is no consensus about one preferred method. This study aimed to evaluate the effect of a new innovative technique called the "double finish line technique" on full-crown retention for short abutments and to compare it with another modified preparation method. A comparative in vitro experimental study was conducted at the Department of Fixed Prosthodontics, Damascus University. The study sample consisted of 30 chromium-cobalt abutments and 30 metal crowns. The sample was divided into three equal groups. The first group was a control group (CG) with a 20-degree total occlusal convergence, 3 mm height, and a 0.5 mm chamfer finish line. The second group had a reduced total occlusal convergence (TOC) in the cervical 1.5 mm of the axial wall from 20 to 8 degrees. The third group implemented the so-called "double finish line technique," adding another 0.5 mm chamfer finish line 1 mm above the first finish line (DFL group). The metal crowns were cemented to metal dies with zinc-phosphate cement. Pull-off tests were applied until failure. Data were analyzed, and the differences between the three groups were detected using one-way ANOVA followed by Bonferroni's post-hoc tests (p<0.05). The mean tensile strength values for the specimens were 115.36 (SD=14.59), 149.60 (SD=11.10), and 42.46 (SD=11.54) for the TOC, DFL, and CR groups, respectively. The reduced total occlusal convergence and double finish line techniques effectively increased full crown retention and resistance cemented on short abutments.

Evaluation of colour change, marginal adaptation, fracture strength, and failure type in maxillary and mandibular premolar zirconia endo-crowns

ObjectivesThe objective of this in vitro study was to evaluate the effects of different preparation designs on the mean colour change (ΔE*), marginal adaptation, fracture resistance, and fracture types of maxillary and mandibular premolar endocrowns (ECs).MethodologyA total of 40 extracted maxillary and mandibular premolars were treated endodontically, and each type was subdivided according to the remaining axial height (remaining walls on all surfaces; 2–4 mm) and 2 mm inside the pulp chamber. Specimens were immersed in coffee for 14 days, ΔE* was determined, marginal adaptation was observed, fracture forces test was conducted, and the samples were examined visually at 10× magnification to evaluate failure type and identify fracture origin. The data were entered and analyzed using Statistical Package for Social Sciences, and significance between and within groups was evaluated through ANOVA. The p-value ≤ 0.05 was considered statistically significant.ResultsThe ΔE* values of the maxillary premolar with 2 mm axial height were the highest (6.8 ± 0.89 units), whereas the lowest value was observed in the mandibular premolar with 4 mm axial height (2.9 ± 0.53 units). Significant differences (p < 0.05) in teeth and design were observed. The marginal adaptation of the mandibular premolar with 4 mm axial height was the highest (30.20 ± 1.53 μm), whereas the lowest marginal adaptation was observed in the maxillary premolar with 2 mm axial height (14.38 ± 0.99 μm), and the difference was statistically significant (p < 0.05). The maximum fracture force was observed in maxillary premolars with 2 mm axial height (2248.15 ± 134.74 N), and no statistically significant difference (p = 0.07) was observed between maxillary and mandibular premolars at 4 mm axial height.ConclusionThe recorded ΔE* values of the ECs were within clinically acceptable values or slightly higher, and the marginal adaption values were within acceptable and recommended clinical values in µm. EC preparation with 2 mm axial height in both arches recorded the highest fracture forces. Type III (split fracture) failure was recorded as the highest in the maxillary and mandibular premolar ECs with different axial wall heights.

Comprehensive sex-specific and age-dependent analysis of 4D-flow MRI assessed aortic blood flow-related parameters in normal subjects using single-vendor MR systems and single-vendor software.

Aortic blood flow characterization by 4D flow MRI is increasingly performed in aneurysm research. A limited number of studies have established normal values that can aid the recognition of abnormal flow at an early stage. This study aims to establish additional sex-specific and age-dependent reference values for flow-related parameters in a large cohort of healthy adults. 212 volunteers were included, and 191 volunteers completed the full study protocol. All underwent 4D flow MRI of the entire aorta. Quantitative values for velocity, vorticity, helicity, as well as total, circumferential, and axial wall shear stress [WSS] were determined for the aortic root [AoR], ascending aorta [AAo], aortic arch [AoA], descending [DAo], suprarenal [SRA], and infrarenal aorta [IRA]. Vorticity and helicity were indexed for segment volume (mL). The normal values were estimated per sex- and age-group, where significant differences between males (M) and females (F) were found only for specific age groups. More specifically, the following variables were significantly different after applying the false discovery rate correction for multiple testing: 1) velocity in the AAo and DAo in the 60-70 years age group (mean±SD: (M) 47.0 ± 8.2cm/s vs. (F) 38.4 ± 6.9cm/s, p=0.001 and, (M) 55.9 ± 9.9cm/s vs. (F) 46.5 ± 5.5cm/s, p=0.002), 2) normalized vorticity in AoR in the 50-59 years age group ((M) 27539 ± 5042s-1mL-1 vs. (F) 30849 ± 7285s-1mL-1, p=0.002), 3) axial WSS in the Aao in the 18-29 age group ((M) 1098 ± 203 mPa vs. (F) 921 ± 121 mPa, p=0.002). Good to strong negative correlations with age were seen for almost all variables, in different segments, and for both sexes. This study describes reference values for aortic flow-related parameters as acquired by 4D flow MRI. We observed limited differences between males and females. A negative relationship with age was seen for almost all flow-related parameters and segments.

A robust three-dimensional numerical model for heat transfer characteristics in sintered–grooved thin flat heat pipes

In the current research, a robust three-dimensional numerical model is developed for thin flat heat pipes (TFHPs) with a hybrid sintered–grooved wick structure. Numerical simulations for laminar incompressible flow in liquid wick and ideal gas incompressible flow in the vapor core are performed to predict temperature, pressure, and velocity profiles. The model utilized non-Darcy transport through a porous wick to determine liquid flow in the liquid-wick section. The mass flow rate of the fluid at the liquid–vapor interface is modeled using kinetic theory. Furthermore, the hybrid wick structure is modeled as an inhomogeneous porous medium. Additionally, this formulation enhances the stability and convergence of the numerical solution and accelerates the solving time. The developed model is validated with experimental data, showing very good agreement with axial wall temperatures, with a maximum error of about 2% in steady-state conditions. The numerical results, including system pressure, wall temperature, mass transfer at the liquid and vapor interface, and velocity magnitude streamlines, are investigated for a comprehensive understanding of the flow physics and performance of the hybrid wick. The results show that, at heat inputs of 5, 10, 20, and 30 W, the thermal efficiency of hybrid wick TFHP is 4.9%, 10.4%, 34.38%, and 23.3%, respectively, greater than that of the grooved wick. The TFHP with a hybrid wick indicates the best thermal efficiency at a heat input of 20 W, with a thermal resistance of 0.95 K/W.

Evaluation of Convergence Angles in Posterior Crown Preparations by Dental Students at Zawia University

Background and objectives: Achieving optimal axial taper and occlusal convergence in crown preparations is a crucial concern among dental students. Proper preparation design is essential for the long-term success of full-coverage restorations. This study aimed to evaluate the convergence angles and axial taper achieved by dental students in their crown preparations. Methods. A total of 80 posterior tooth preparations (40 mandibular first molars and 40 mandibular second molars) created by second-year dental students on a dental simulator were analyzed. The total occlusal convergence (TOC), bucco-lingual (BL) and mesio-distal (MD) convergence angles, as well as the degree of taper on the axial walls, were measured using the B&amp;B dental software (Guide system, B&amp;B, Italy). Statistical analysis was performed using SPSS version 27. Results. The overall mean of the total convergence angle was 21.88°, with a BL convergence angle mean value of 23.11° (standard deviation of 13.3°) and an MD convergence angle mean value of 20.66° (standard deviation of 11.0°). The results showed a statistically significant difference between the mesial axial taper and the distal axial taper (p-value &lt; 0.001). However, no significant differences were observed between the buccal axial taper and lingual axial taper (p-value &gt; 0.05), or between the BL convergence angle and MD convergence angle (p-value &gt; 0.05). Conclusion. The study revealed variations in the convergence angles of full metal crown preparations created by dental students. The recommended convergence angle was difficult for these students to achieve.

Study on explosion impact pressure and damage distribution law of rock powder segmented charge

The charge structure is the critical to determine the bench blasting effect of rock slope. Through theoretical calculation, model testing, and numerical simulation, a formula for calculating the stress attenuation of the axial hole wall of the segmented charging structure is proposed. Moreover, the influence mechanism of the explosive ratio and interval packing length on the internal damage distribution of the concrete of concrete specimens under a segmented charging structure of the cuttings is described. Finally, the research results are applied to the mining of a rock slope in southwest China. The research results reveal the following: 1) The pressure at the charge section is highest when the rock debris interval charge is used, and with the increase in the charge section distance, the pressure markedly decreases—sharply first before stabilizing. In the upper filling interval charge section, the minimum pressure corresponded to approximately the midway point of the filling section, and the stress distribution on the axial hole wall is concave: high at both ends and low in the middle. 2) The ratio of the upper and lower sections of the explosive column determines the form of blasting damage, and the range of blasting damage increases first and then decreases with the increase in the length of the rock debris in the interval section. 3) The field test shows that compared with the traditional blasting charge structure, the optimized segmented charge structure can reduce the blasting block rate by 13.1%. 4) Using the optimized charge structure, the explosive unit consumption can be decreased from 0.27 kg/m3 to 0.24 kg/m3, which improves the economic benefits of mining and construction of related mines.

An overview of conjugate heat transfer augmentation methods for thermal management and recent advancements in microchannel heat sink overall performance

Recent technological advancement creates high-dense circuits development which creates colossal cooling demand requirements. In the future, advanced technology and scientific applications need to balance heat fluxes beyond limitation that catalyse the research opportunities further to achieve cooling requirements. Conventional cooling equipment is inappropriate for extracting heat from microchips within the minimal surface area. Microchannel technology appeared as a next-generation heat exchanger for the given heat duty. In the classical case of accounting, micro-heat exchangers both axial and transverse wall conduction effects is usually neglected. However, from the year 2005 onwards, researchers identified conduction dominance at fluid velocity is zero zones at the interface, which created balance between conduction–convection currents, finally included axial wall/heat conduction effects to a general model. This present study made a comparative evaluation fluid flow, heat transfer characteristics, thermal performance (TP) based on geometrical parameters, substrate materials and discusses previous issues, and current issues-based future research directions. Till today, based on applications of microchannels in thermal management, several experimental and numerical investigations have been reported for further improvement in TP. However, many researchers are still trying to accomplish things over a long period. Therefore, an overview of previous studies is furnished in the present study to assist researchers in this area much useful for further improvement.

Effect of the Inter-Tooth Distance and Proximal Axial Wall Height of Prepared Teeth on the Scanning Accuracy of Intraoral Scanners.

This study aimed to analyze the effect of the height of the proximal axial wall of the prepared tooth and the distance between the adjacent tooth and the prepared tooth on the scan accuracy of intraoral scanners. Ten working casts with maxillary first molars prepared to receive zirconia crowns were randomly obtained from a dental clinic. Each of the 10 casts was scanned using two intraoral scanners (i700; MEDIT and CS3600; Carestream; computer-aided design [CAD] test model, CTM; N = 15 per working cast) 15 times per scanner. Individual dies of the prepared teeth were fabricated, and high-precision scan data were acquired using a laboratory scanner (CAD reference model, CRM; N = 1). CTMs were aligned relative to the prepared tooth of CRMs by using three-dimensional inspection software (Ver 2018.1.0; Control X; 3D Systems). Data were statistically analyzed using an independent t-test and one-way analysis of variance for between-group comparisons (α = 0.05). The inaccuracy in the proximal regions (mesial or distal) of the prepared tooth was higher than that in the buccal and lingual regions (p < 0.05). The scan accuracy was not correlated with the variables when the distance between the adjacent tooth and the prepared tooth was ≥2.0 mm and the height of the proximal axial wall of the prepared tooth was <3.0 mm (p > 0.05). Therefore, an excellent scan accuracy can be obtained using an intraoral scanner when the distance between the adjacent tooth and the prepared tooth is ≥2.0 mm and the proximal axial wall height of the prepared tooth is <3.0 mm.

Digital Evaluation of the Depth and Width of Upper and Lower Molar Cavity Preparations of Dental Students

Objective: The aim of this study was to evaluate the mesial and distal seat widths and the buccal, lingual, and axial wall height values of cavity preparations by measuring them with the help of a digital scanner.&#x0D; Methods: In this study, 70 randomly selected students of 140 tooth preparations (mandibular molar and a maxillary molar cavities) of phantom jaw models were evaluated. The prepared teeth were scanned with an intraoral scanner. The parameters used in the analysis were the depth values of the buccal and lingual (or palatal) wall depth, the mesial and distal axial wall height, and the mesial and distal seat width values. For main effects and interactions, two-way analysis of variance was used, and for multiple comparisons, Tukey’s test was used (p &lt; .05).&#x0D; Results: No significant difference was found in the teeth according to cavity depth. However, a significant difference was found in the cavity regions’ depths or widths. There was no difference between the total buccal (1.93 ± 0.01 mm) and lingual (1.91 ± 0.32 mm) depth values. There was no difference between the total mesial (1.51 ± 0.27 mm) and distal (1.41 ± 0.26 mm) seat width values. There was no difference between the total mesial (1.11 ± 0.35 mm) and distal (1.21 ± 0.27 mm) axial wall height values. &#x0D; Conclusion: It was observed that the students had more difficulty in the distal region of the tooth than in the mesial region. Digital methods in preclinical education can provide objective results in the evaluation of cavity preparations.

A scoring system for grading corkscrew claws in dairy cattle

Corkscrew claw (CC) in dairy cattle is increasingly reported in dairy herds. CC is a progressive deformity of the claw capsule with uncertain aetiology and pathogenesis. Genetics and specific environmental factors are suspected of contributing to the development of this irreversible condition. CC has been found in lame cows; however, the cause and effect has not been established. To perform analysis of risk factors, treatment and pathogenesis, a definition of severity scores is called for. The aim of this study was to measure and analyse CC characteristics from photos of cows’ feet to describe and evaluate a scoring system for CC. Width of the visible part of the axial wall, degree of contact between the toe and the floor and angle of the distal part of the abaxial wall as a proxy for the deviation of the abaxial wall was measured from 393 pictures of CC. Based on the measurements on the claws, the parameter “width of the axial wall” was chosen to define the scores. The parameter was divided into three intervals to define either mild CC 0.3–2.0 cm, moderate CC 2.1–3.5 cm or severe CC>3.5 cm and correlation between the parameters; level of contact between the toe and the floor and the angle of the distal abaxial wall was evaluated.There was a significant positive linear correlation between width of the axial wall and angle of the distal part of the abaxial wall (r=0.91), the wider the axial wall, the more the abaxial wall deviated in the distal part. As the width of the axial wall increased the toe increasingly lost contact with the floor, this association was significant for mild CC and moderate CC but not for severe CC. The Interobserver agreement of the CC Scoring system was tested by 30 claw trimmers each scoring 32 cadaver feet and by 2 trained observers on 28 photos of feet using Cohen´s weighted kappa and showed substantial to almost perfect agreement between untrained and trained observers, respectively.

Marginal Fit and Internal Adaptation of Monolithic Zirconia 3-Unit Fixed Dental Prosthesis: In Vitro Study.

To compare the marginal and internal fit of monolithic zirconia (MZ) 3-unit fixed dental prostheses (FDPs) fabricated using two CAD/CAM workflows: full-chairside (FCH) and lab (LAB). The right maxillary first premolar and first molar were prepared for MZ 3-unit FDPs on a typodont. CEREC Primescan digitized the typodont model 15 Omes. A total of 30 FDPs was fabricated using two processes: FCH (n = 15) and LAB (n = 15). FCH and LAB FDPs were designed using CEREC SW 4.5.1 and Exocad and milled using CEREC MC X and Zirkonzhan 600/V3, respectively. A fast-sintering protocol was used in both groups. A dual-scan technique was used to assess the cement space at the occlusal surface (OC), axial wall (AX), and margin (MA). Statistical analysis of the results was performed using univariate ANOVA with Scheff. post hoc test (a = .05). Measurements in the FCH and LAB groups were within the clinically acceptable marginal and internal fit. The fit of FCH FDPs at MA, AX, and OC was 77.50 ± 29.99 μm, 99.67 ± 21.58 μm, and 150.03 ± 30.78 μm, respectively. The fit of LAB FDPs at MA, AX, and OC was 100.27 ± 27.06 μm, 116.53 ± 17.90 μm, and 142.30 ± 19.00 μm, respectively. The difference between the two groups was not statistically significant. MZ 3-unit FDPs fabricated using FCH have clinically acceptable marginal and internal fit. This result verifies the ability of FCH workflow to fabricate MZ mulOunit FDPs in a single visit.

Evolution of the Júcar-Cabriel fluvial system on the Mediterranean watershed of the Iberian Peninsula (Valencia, eastern Spain)

This study presents the characterization and chronology of the Quaternary terrace sequence developed in the confluence zone of the Júcar and Cabriel river valleys. The study area covers a radius of 10 km from the confluence of the two valleys near the locality of Cofrentes (Valencia). It is located in the northern zone of the Ayora-Cofrentes Graben in the northeastern sector of the External Prebetic Zone adjacent to southern Iberian Chain. This N-S graben is an inherited tectonic feature with an axial salt wall subject to different periods of fluvial dissection and refilling since at least the end of the Messinian Salinity Crisis (MSC). Regional isostatic uplift and local uplift and subsidence processes related to salt flow and dissolution during the Quaternary period, favored by fluvial entrenchment and terrace development. The terrace system and the previous pre-incision erosional and depositional surfaces are analyzed from a geomorphological point of view. The terrace system only develops within the soft Mio-Pliocene sedimentary fill of the graben, whilst upstream and downstream this zone the studied valleys develop important gorges (canyons) carved in the Cretaceous tablelands (Caroch Massif) and Mio-Pliocene deposits (Llanura Manchega). The geochronological control is established from 20 numerical ages obtained by different dating methods, such us Electron Spin Resonance (ESR), Optically Stimulated Luminescence (OSL) in detrital sequences and Th/U series in calcareous tufa deposits. Additionally, four K/Ar dates available for volcanic materials disrupting the upper and oldest terrace have been considered. A total of 14 terrace levels were identified between +130–135 m (T1) and +3–4 m (T14) of relative height above the river thalwegs. The T1 has an approximate age of c. 1.6–2.0 M.a. as indicate the age of the volcanic materials from the Agras Volcano intruded in the terrace, marking the onset of Quaternary fluvial dissection in the zone. The obtained geochronological data indicate that the Lower-Middle Pleistocene boundary is slightly above T6 (+60–65 m), which has an ESR age of 577 ± 43 ka. This terrace also documents the onset of the most important period of rise of the salt within the graben interfering drainage development. The geochronological data indicate the occurrence of a second eruptive event during the second half of the Middle Pleistocene related to the terraces T7 (+50 m) and T8 (+35–40 m), updating the volcanic activity in the zone. The beginning of the Upper Pleistocene is recorded by the top sequences of the T9 terrace (+25–30 m) where numerous OSL and Th/U data have been obtained with ages between ca. 105 and 81 ka (MIS 5). However, these young terraces (T8 to T13) are thickened (8–10 m) recording Middle Pleistocene sediments in their basal sequences with ages between ca. 193 and 137 ka (MIS 6). The study provides important data on valley evolution under the interference of volcanic activity, salt –related deformation (diapirism, solution subsidence) and fluvial incision fostered by the rise of the axial diapir (salt wall) protruding the graben since at least the Brunhes-Matuyama boundary. The analyzed fluvial evolution documents interesting cases of river capture, drainage antecedence and tectonic adaptation of the drainage throughout the Quaternary Period. The paper also poses interesting geochronological data on the long-term Quaternary evolution of Mediterranean valleys in the Iberian Peninsula, poorly explored to the date.

The influence of pontic distribution on the marginal and internal gaps of CAD/CAM five-unit anterior zirconia framework

Background/purposeNowadays, zirconia-based framework has been used for longspan or full-arch fixed dental prostheses (FDPs). This study aimed to evaluate the effect of pontic distribution on marginal and internal gaps of five-unit anterior zirconiabased DPs. Materials and methodsRight maxillary central incisor and second premolar were selected as terminal abutments and three different edentulous conditions with one nonterminal abutment were simulated. Marginal and internal gaps in each zirconia-based samples(n = 10) were examined by computer-aided replica technique. Five regions, including marginal gaps at mesial or distal finishing line, internal gaps at the mesial or distal axial wall, and occlusal surface, were statistically analyzed (α = .05). ResultsMost of marginal gaps and internal gaps at axial wall were clinically acceptable, but larger at occlusal surface. For the three experimental groups, clinically accepted percentage with qualified gaps were less than 30%.There were statistical differences at axial wall over pontic side and marginal gaps over non-pontic side between groups (P<0.05). For sum of gaps of all abutments in each group, statistical differences were found at marginal and axial wall (P < 0.05). As for those on terminal and non-terminal abutments, statistical differences were found on second premolar (P < 0.05). ConclusionExcept for occlusal surface, the overall marginal gaps and internal gaps at axial wall of five-unit anterior zirconia-based FDPs with different pontic distribution were clinically acceptable. However, the percentage with qualified gaps were low (<30%). Greater gaps were noted when adjacent pontic existed. Different pontic size and distribution with curvature had an influence on the gaps.

Marginal fit of 3D printed interim crowns fabricated with intraoral scanners over conventional and reverse-tapered preparations

Background/Aim: 3D printing technology has become increasingly prevalent in the field of dentistry. Research is ongoing regarding the usability of resin-based 3D printed temporary crowns in clinical applications. Marginal fit of 3D printed interim restorations produced from digital impressions obtained with intraoral scanners may vary according to the geometry and inclination of the axial walls of the abutment tooth. The purpose of this in vitro study was to evaluate the marginal fit of 3D printed interim crowns fabricated over conventional and reverse-tapered preparations. Material and Methods: Crown preparations with known total occlusal convergence (TOC) angles (-8°,-4°, 0°, 8°, 12°, 16°, and 22°) were digitally created from a maxillary central incisor and printed in acrylic resin. Then, prepared tooth models (n=7) were scanned 10 times with an intraoral scanner (TRIOS3, 3Shape Inc, Denmark). Each experimental scan was used to design and fabricate a 3D printed interim anatomically contoured crown. Vinyl polyether silicone was used three times to assess the marginal discrepancy of the specimens by measuring five marginal points on digital photographs for each surfaces (buccal, mesial, distal, lingual). Marginal fit measured values did not follow a normal distribution; therefore, the Kruskal-Wallis and the Dunn/Bonferroni multiple comparison tests were applied (p = 0.05). Results: Marginal gap values were found significantly higher (p&lt;0.05) in crowns produced for specimens with-8 and-4 degrees axial wall than other specimens. Conclusions: Negative inclination of the axial walls adversely affects the marginal fit of crowns produced with 3D printing technology.

Evaluation of the effect of surface roughness and modification of implant abutment axial wall on the retention of zirconium oxide copings before and after thermocycling.

The purpose of this study was to determine the effect of one-wall elimination of the abutment and also the surface treatment of the abutment on the retention of cement-retained, implant-supported zirconium oxide copings. In this experimental study, four straight abutments were connected to four implant analogs (DIO, UF, Busan, Korea) with 35 Ncm torque. They are mounted vertically in resin blocks. Abutments were prepared as following groups: A) abutment was used in its intact standard form as a control group. B) 4 mm of the flat wall was removed to produce an abutment with 3 walls. C) The abutment surface was abraded with 50 µm AL2O3 powder. D) 4 mm of a flat wall of the abutment was removed, then the abutment surface was abraded with 50 µm AL2O3 airborne particle.10 zirconium oxide copings were made. Samples were cemented with temp bond NE to abutments. The retention of copings was measured before and after incubation using the universal testing machine. T-test, one-way ANOVA, and Post Hoc Tukey Test were used for statistical analysis of data. In all groups, retention was decreased after thermocycling (P ≤0.001). 3 wall abutments had less retention than the control group before thermocycling. A significant difference was detected between 3 wall abutments and 4 walls of sandblasted abutments before thermocycling. After thermocycling, no difference in retention was seen between groups. Thermocycling significantly reduces the retention of implant-supported ceramic copings. Sandblasting abutments with 50 µm AL2O3 air-borne particles did not increase the retention of ziconium oxide copings which were cemented with temp bond NE. One wall elimination of abutment decreased the retention of zirconia copings. Key words:Retention, crown, abutment, zirconia coping, sandblasting.

Observation of intracranial artery and venous sinus hemodynamics using compressed sensing-accelerated 4D flow MRI: performance at different acceleration factors.

To investigate the feasibility and performance of 4D flow MRI accelerated by compressed sensing (CS) for the hemodynamic quantification of intracranial artery and venous sinus. Forty healthy volunteers were prospectively recruited, and 20 volunteers underwent 4D flow MRI of cerebral artery, and the remaining volunteers underwent 4D flow MRI of venous sinus. A series of 4D flow MRI was acquired with different acceleration factors (AFs), including sensitivity encoding (SENSE, AF = 4) and CS (AF = CS4, CS6, CS8, and CS10) at a 3.0 T MRI scanner. The hemodynamic parameters, including flow rate, mean velocity, peak velocity, max axial wall shear stress (WSS), average axial WSS, max circumferential WSS, average circumferential WSS, and 3D WSS, were calculated at the internal carotid artery (ICA), transverse sinus (TS), straight sinus (SS), and superior sagittal sinus (SSS). Compared to the SENSE4 scan, for the left ICA C2, mean velocity measured by CS8 and CS10 groups, and 3D WSS measured by CS6, CS8, and CS10 groups were underestimated; for the right ICA C2, mean velocity measured by CS10 group, and 3D WSS measured by CS8 and CS10 groups were underestimated; for the right ICA C4, mean velocity measured by CS10 group, and 3D WSS measured by CS8 and CS10 groups were underestimated; and for the right ICA C7, mean velocity and 3D WSS measured by CS8 and CS10 groups, and average axial WSS measured by CS8 group were also underestimated (all p < 0.05). For the left TS, max axial WSS and 3D WSS measured by CS10 group were significantly underestimated (p = 0.032 and 0.003). Similarly, for SS, mean velocity, peak velocity, average axial WSS measured by the CS8 and CS10 groups, max axial WSS measured by CS6, CS8, and CS10 groups, and 3D WSS measured by CS10 group were significantly underestimated compared to the SENSE4 scan (p = 0.000-0.021). The hemodynamic parameters measured by CS4 group had only minimal bias and great limits of agreement compared to conventional 4D flow (SENSE4) in the ICA and every venous sinus (the max/min upper limit to low limit of the 95% limits of agreement = 11.4/0.03 to 0.004/-5.7, 14.4/0.05 to -0.03/-9.0, 12.6/0.04 to -0.03/-9.4, 16.8/0.04 to 0.6/-14.1; the max/min bias = 5.0/-1.2, 3.5/-1.4, 4.5/-1.1, 6.6/-4.0 for CS4, CS6, CS8, and CS10, respectively). CS4 strikes a good balance in 4D flow between flow quantifications and scan time, which could be recommended for routine clinical use.