Fungal Attack Research Articles

Resistance of Chip Block Pallet from Teak Wood Particle against Decay Fungi and Subterranean Termites

Wood biomass such as sawdust, particles, and chip obtained wood industry can be used as raw material for chip block pallets (CBP). This study evaluated the resistance of chip block pallets made from teak-sawn waste and polyurethane adhesive against decay fungi (white-rot and brown-rot fungi) and subterranean termites. The CBPs with dimensions of 9 × 9 × 9 cm and a target density of 0.6 g/cm3 were cold pressed at 9.8 MPa for 4 h using several polyurethane concentrations and composition of particle sizes. The termite and decay resistance tests were conducted following JIS K 1571 2004. The results showed that CBP treated with different polyurethane concentrations and composition of particle sizes was resistant to subterranean termite attacks. However, the CBP manufactured were not resistant to white-rot and brown-rot fungi attacks, showing more than 3% mass loss percentage. Considering the efficiency of polyurethane use, the study suggested the best content for using polyurethane in the manufacture of CBP is 4.5% with a particle size composition of 50 (4-14 mesh): 50 (> 60 mesh). Keywords: Biodeterioration, chip block pallet, polyurethane, teak wood particles

Are the Blueberries We Buy Good Quality? Comparative Study of Berries Purchased from Different Outlets.

Blueberries (Vaccinium corymbosum L.) are becoming increasingly popular for their nutritional and health benefits, and their economic value is therefore increasing. The loss of quality that can occur due to softening and fungal attack is an important consideration when marketing blueberries. Despite the added value of blueberries, no studies have been carried out on how the fruit arrives at the outlets just before purchase by the consumer in terms of firmness, physico-chemical parameters, phenolic compounds, and fungal growth. The aim of this work has been, therefore, to investigate possible differences in quality parameters between blueberries purchased from ten different outlets, regardless of the supplier. The results showed that all the samples were of acceptable quality, although they all had a low maturity index at the point of sale. None of the samples studied showed clear signs of fungal decay at the time of purchase, although we were able to grow and identify some pathogen specimens after cultivation. In terms of total phenolic and anthocyanin content, as well as antioxidant activity, all the samples showed low values, possibly due to their postharvest storage, but they were within the expected range for this fruit. On the other hand, differences in the measured parameters were observed between samples of the same cultivar while no differences were found between conventionally and organically grown blueberries. This suggests that preharvest (such as edaphoclimatic conditions, agricultural practices, and cultivars) and postharvest factors (such as treatments used, storage, and transport temperatures) could influence the berry quality when they reach the consumer.

Concurrent application of bacterial-mediated and mycosynthesized ZnO nanofungicides to maintain high ascorbic acid and delay postharvest decay of apricot

Quality of apricot fruit is affected by different biotic stresses during growth, harvesting and storage. Due to fungal attack, huge losses of its quality and quantity are observed. The present research was designed for the diagnoses and management of postharvest rot disease of apricot. Infected apricot fruit were collected, and the causative agent was identified as A. tubingensis. To control this disease, both bacterial-mediated nanoparticles (b-ZnO NPs) and mycosynthesized nanoparticles (f-ZnO NPs) were used. Herein, biomass filtrates of one selected fungus (Trichoderma harzianum) and one bacterium (Bacillus safensis) were used to reduce zinc acetate into ZnO NPs. The physiochemical and morphological characters of both types of NPs were determined. UV–vis spectroscopy displayed absorption peaks of f-ZnO NPs and b-ZnO NPs at 310–380 nm, respectively, indicating successful reduction of Zinc acetate by the metabolites of both fungus and bacteria. Fourier transform infrared (FTIR) determined the presence of organic compounds like amines, aromatics, alkenes and alkyl halides, on both types of NPs, while X-ray diffraction (XRD) confirmed nano-size of f-ZnO NPs (30 nm) and b-ZnO NPs (35 nm). Scanning electron microscopy showed flower-crystalline shape for b-ZnO NPs and spherical-crystalline shape for f-ZnO NPs. Both NPs showed variable antifungal activities at four different concentrations (0.25, 0.50, 0.75 and 1.00 mg/ml). Diseases control and postharvest changes in apricot fruit were analyzed for 15 days. Among all treatments, 0.50 mg/ml concentration of f-ZnO NPs and 0.75 mg/ml concentration of b-ZnO NPs exhibited the strongest antifungal activity. Comparatively, f-ZnO NPs performed slightly better than b-ZnO NPs. Application of both NPs reduced fruit decay and weight, maintained higher ascorbic acid contents, sustained titratable acidity, and preserved firmness of diseased fruit. Our results suggest that microbial synthesized ZnO NPs can efficiently control fruit rot, extend shelf life, and preserve the quality of apricot.

The Role of Biofertilizers in Sustainable Agriculture: An Eco-Friendly Alternative to Conventional Chemical Fertilizers

Empirical observations and theory both discourage the production and use of chemical fertilizers as they can lead to environmental pollution, soil degradation and reduction in soil fertility in the long term. In certain cases, excess nutrients from chemical fertilizers such as nitrogen and phosphorus can leach into nearby water causing eutrophication. Also, the production process requires large amounts of energy, which often comes from burning fossil fuels contributing significantly to greenhouse gas concentration. Biofertilizers present a promising alternative to chemical fertilizers and improve agricultural sustainability and reduce environmental pollution. However, there is still more to learn about the potential benefits of biofertilizers based on factors such as soil type, crop species, and environmental conditions. This review shows the Trichoderma species as one of the most prominent biofertilizers that can help in plant growth promotion and serve as a biocontrol agent against plant pathogens. An extensive summary of scientific literature on Trichoderma’s production, effectiveness in comparison to chemical fertilizers and its potential for use are discussed. Trichoderma species have been documented to possess numerous mechanisms to combat a wide range of plant pathogens, protect plants from biotic and abiotic stresses, reduce drought and salinity stress fungal attacks and promote root growth. Trichoderma is an ecofriendly organic fertilizer that can promote food security and enhance sustainable crop production. This article provides a comprehensive and up-to-date summary of the current state of knowledge on Trichoderma as a biofertilizer and indicates future research directions.

Preservatve Potentials of Datura metel Seed Oil on Triplochiton scleroxylon Wood (Schumann)against Fungal Attack

This experiment was carried out to evaluate the potential of extracted Datura metel seed oil as a bio wood preservative against fungi attack as reports have shown bio-preservatives to be toxic free and environmentally friendly. The oil was extracted from the seed by Soxhlet apparatus using N-Hexane and ethanol solvents and using volume-to-volume method of dilution kerosene (at 50%) was added to increase its quantity thereafter. The phytochemical screening of the seed of Datura metel revealed the presence of tannins, alkaloids, flavonoids, saponins and phenols. Wood samples of Triplochiton sceleroxylon were cut to 20 × 20 × 60mm and the dimensioned wood samples were soaked for 72 hours in the seed oil extract hence preservative absorption rate and percentage weight loss of wood was determined on exposure to a purely cultured Sclerotium rolfsil (brown rot fungi) and Pleurotus ostreatus(white rot fungi). Data obtained were subjected to analysis of variance at α0.05 and the results showed the highest value of mean weight loss of 18.29% while the samples exposed to brown rot fungi has a mean value of 14.12% and white rot a lowest mean value of 12.72%. The highest absorption was observed to be 92.73 kg/m at 100 % concentration level of D,metel extract. Based on the results obtained, the seed-oil extracts of Datura metel have the potential of being an effective wood preservative.

Identification of Contaminant Fungi for Cocoa Seeds (Theobroma cacao L.) During Storage in the Exporter's Warehouse, Sorong City, Southwest Papua

The low quality of cocoa beans because they do not meet SNI standards can cause losses for exporters because they are subject to automatic discounting as a result of the product being detained (automatic detention). This problem can affect the competitiveness of Indonesian cocoa in international market trade. Anticipation of the low quality of export cocoa beans really needs to be done to minimize the level of damage to cocoa beans due to contaminant fungal attacks. The types of contaminant fungi that attack cocoa beans are from the genera Aspergillus, Penicillium, Fusarium, Rhizopus and Mucor. The research was conducted from June to August 2022 at the Sorong City Plant Quarantine Laboratory. The study used a qualitative method and took a sample of 0.5 kg of cocoa beans from the top, middle and bottom of the storage sacks in the exporter's warehouse, using a purposive sampling method. The results of the study found 7 types of contaminant fungi and 4 species from the Ascomycetes class which mostly attacked cocoa beans, namely Aspergillus flavus, Aspergillus fumigatus, Aspergillus clavatus and Penicillium sp.

A Case Study of Renaissance Wall Paintings in Granada (Spain): Historical–Artistic Analysis, Materials Characterization, and State of Conservation

The research carried out on the wall paintings of Hernán Pérez del Pulgar’s Palace chapel in Granada (Spain) was aimed at determining its historical–artistic, stylistic, technical, and compositional aspects. For this, a 16th century frieze and an 18th century pendentive were studied. The mineralogical, chemical, and textural characterization of the constituent materials and the study of the state of conservation of the paintings have helped to determine the pictorial technique used, identify the nature of the salts present in the paintings, and other pathologies including a dormant fungal attack. To this end, optical microscopy (OM), X-ray diffraction (XRD), Field emission scanning electron microscopy with microanalysis (FESEM-EDS), and micro-Raman spectroscopy (MRS) were used. The information obtained helps clarify important aspects of the painting technique used, laying a basis to ensure effective and suitable conservation and restoration measures on the paintings that will ensure their durability over time.

Synergic effect of basalt/wood fiber reinforced polylactic acid hybrid biocomposites against fungal decay

In addition to the traditional fibre-reinforced composites, the investigation of novel composites with significant potential for engineering applications attracts increasing attention. In this study, the decay resistance of basalt and/or wood fibre-reinforced polylactic acid (PLA) biocomposites was evaluated with a soil block test by using white rot fungi, Trametes versicolor (Trv) and Irpex lacteus (Irl), and brown rot fungi, Poria placenta (Pop) and Gloeophyllum trabeum (Glt), and a soft rot fungus, Chaetomium globosum (Chg) after 8 weeks of water submersion. Water absorption rate during the water submission and weight losses after the decay test were determined. Furthermore, decay in biocomposites was characterized by SEM and ATR-FTIR. Results showed that the water absorption increased between 52.4–67.5% for wood fibre composites when compared to basalt fibre-reinforced biocomposites. PLA showed good decay resistance against all fungi attacks. However, as the ratio of basalt and wood fibre in the hybrid biocomposites increased, the fungi resistance decreased. The lowest weight loss, 4.9% was found in the biocomposites containing the highest percentage of basalt fibre. On the other hand, the highest weight loss, 54.2% was observed in the composites containing the highest percentage of wood fibre. The results clearly showed that the hybridization of basalt and wood fibres improves the decay resistance of the biocomposites compared to only wood fibre-reinforced composites. However, as the percentage of wood increased in the composites, the decay resistance decreased. SEM and FTIR analysis confirmed the degradation and revealed the degradation mechanism.

Lignin Nanoparticles with Entrapped Thymus spp. Essential Oils for the Control of Wood-Rot Fungi.

After decades of utilization of fossil-based and environmentally hazardous compounds for wood preservation against fungal attack, there is a strong need to substitute those compounds with bio-based bioactive solutions, such as essential oils. In this work, lignin nanoparticles containing four essential oils from thyme species (Thymus capitatus, Coridothymus capitatus, T. vulgaris, and T. vulgaris Demeter) were applied as biocides in in vitro experiments to test their anti-fungal effect against two white-rot fungi (Trametes versicolor and Pleurotus ostreatus) and two brown-rot fungi (Poria monticola and Gloeophyllum trabeum). Entrapment of essential oils provided a delayed release over a time frame of 7 days from the lignin carrier matrix and resulted in lower minimum inhibitory concentrations of the essential oils against the brown-rot fungi (0.30-0.60 mg/mL), while for the white-rot fungi, identical concentrations were determined compared with free essential oils (0.05-0.30 mg/mL). Fourier Transform infrared (FTIR) spectroscopy was used to assess the fungal cell wall changes in the presence of essential oils in the growth medium. The results regarding brown-rot fungi present a promising approach for a more effective and sustainable utilization of essential oils against this class of wood-rot fungi. In the case of white-rot fungi, lignin nanoparticles, as essential oils delivery vehicles, still need optimization in their efficacy.

Cladosporium cladosporioides (strain Clc/1): a candidate for low-density polyethylene degradation

BackgroundPlastic is one of the most widely used materials worldwide in various fields, including packaging and agriculture. Its large quantities require proper disposal and for this reason more and more attention is paid to the issue of degrading plastic. Thanks to the production of non-specific enzymes, fungi are able to attack complex and recalcitrant xenobiotics such as plastics. In recent years, several spectroscopic methods were used to study the plastic degradation ability of different fungal species. Among these, Fourier transform infrared (FT-IR) and FT-Raman spectroscopy techniques are the most used. Surface-enhanced Raman scattering (SERS) spectroscopy is a powerful technique which uses metal nanoparticles (NPs) to enhance the Raman signal of molecules adsorbed on the NPs surface. In this work, the isolation of different fungi from field-collected plastic debris and the ability of these isolates to growth and colonizing the low-density polyethylene (LDPE) were explored by using scanning electron microscope (SEM), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) and SERS spectroscopies.ResultsForty-seven fungal isolates belonging to 10 genera were obtained; among them only 11 were able to grow and colonize the LDPE film. However, after 90 days trial, only one isolate of Cladosporium cladosporioides (Clc/1) was able to carry out the initial degradation of the LDPE film. In particular, based on SEM observations, small cavities and depressed areas of circular shape were visible in the treated samples. Additionally, ATR-FTIR, normal Raman and SERS analyses supported the structural changes observed via SEM. Notably, ATR-FTIR and normal Raman spectra showed a significant decrease in the relative intensity of the methylene group bands. Similarly, the SERS spectra of LDPE after the fungal attack, confirmed the decrease of methylene groups bands and the appearance of other bands referring to LDPE polyphenolic admixtures.ConclusionsThese results suggest that Cladosporium cladosporioides Clc/1 is able to carry out an initial degradation of LDPE. Moreover, combining ATR-FTIR, Raman and SERS spectroscopies with SEM observations, the early stages of LDPE degradation can be explored without any sample pretreatment.Graphical

Stilbene Content and Expression of Stilbene Synthase Genes in Korean Pine Pinus koraiensis Siebold & Zucc

Stilbenes are a large group of plant phenolic compounds that have a wide range of biologically active properties, such as antioxidant, immunomodulatory, anti-inflammatory, and anti-angiogenic effects. In plants, stilbenes are involved in the defense against environmental stresses, including fungal infections and insect attacks. The biosynthesis of stilbenes is well described for those plant species where resveratrol and its derivatives are the predominant stilbenes. However, there is little information on stilbene biosynthesis in the Pinaceae family, although the highest content of stilbenes was found in plants of this family. In this study, seasonal variations in stilbene compositions and contents in different parts of Pinus koraiensis was described (needles, bark, wood, young branches, and strobiles). HPLC-ESI-MS analysis showed the presence of seven stilbenes in P. koraiensis: t-astringin; t-piceid; cis-piceid; t-isorapontin; t-pinostilbenoside; t-resveratrol; and t-pinostilbene. Glycosylated and methylated forms of stilbenes, such as t-astringin, t-piceid, and t-pinostilbenoside, prevailed over other stilbenoids. The highest content of stilbenes was detected in the bark collected in spring and winter (up to 54.8 mg/g dry weight). The complete protein-coding sequences of three stilbene synthase genes, PkSTS1, PkSTS2, and PkSTS3, were obtained from the RNA isolated from the P. koraiensis needles. The expression of the PkSTS1, PkSTS2, and PkSTS3 genes was analyzed using real-time PCR and frequency analysis of cloned RT-PCR products in the needles of P. koraiensis collected in different seasons. Thus, we first analyzed stilbene biosynthesis in the different organs of pine P. koraiensis and PkSTS expression depending on the year seasons.

Synergistic inhibition effect of ultraviolet irradiation and benzalkonium chloride on the corrosion of 316L stainless steel caused by Aspergillus terreus

Microbiologically influenced corrosion (MIC) is a key factor that damages engineering materials in marine environments. One of the major concerns in this regard is the corrosion protection of stainless steel (SS) caused against fungal attacks. This study investigated the effect of ultraviolet (UV) irradiation and benzalkonium chloride (BKC) on the corrosion of 316L stainless steel (316L SS) induced by marine Aspergillus terreus in 3.5 wt% NaCl solution. This was accomplished by employing microstructural characterisations and electrochemical analysis to analyse the synergistic inhibition behaviour of the two methods. The results indicated that while UV and BKC demonstrated individual abilities to suppress the biological activity of A. terreus, their inhibitory effects were not significant. The combination of UV light and BKC was found to cause a further decline in the biological activity of A. terreus. The analysis revealed that the combination of BKC and UV significantly decreased the sessile cell counts of A. terreus by more than three orders of magnitude. The fungal corrosion inhibition effect of individual application of UV light or BKC did not yield satisfactory results owing to the low intensity of UV and low concentration of BKC. Furthermore, the corrosion inhibition of UV and BKC occurred mainly during the early stages. The corrosion rate of the 316L SS declined rapidly when the combination of UV light and BKC were used, indicating that UV light and BKC exert a good synergistic inhibitory effect on the corrosion of the 316L SS caused by A. terreus. Therefore, the results suggest that the combination of UV light and BKC can be an effective approach to control the MIC of 316L SS in marine environments.

AKTIVITAS ANTI BAKTERI FORMULASI LOTION EKSTRAK ETANOL RIMPANG JERINGAU PUTIH

The skin is the most important and largest organ of the human body. The skin needs so much attention, both in terms of disease and health, because it turns out that the skin itself is quite susceptible to bacterial and fungal attacks. Therefore, the formulation of lotions for the skin, namely ingredients that can kill bacteria or fungi and are safe for the skin can be justified. Natural ingredients that have properties as antibacterial ingredients for the skin are White Jeringau.The purpose of this study was to explain the differences in the inhibition of the lotion formulation of the ethanol extract of the White Jeringau Rhizome against the growth of Staphylococcus aureus bacteria using the diffusion method. The research method used is a quasi-experimental with purposive sampling technique. The sample in this study was the lotion of the ethanol extract of the Jeringau Putih rhizome with concentrations of 40%, 50% and 60% which were replicated 9 times each so that the number of samples in this study were 27 samples. Furthermore, the sample was tested for inhibition of Staphylococcus aureus bacteria by diffusion method.Based on the results of this study in 2022, antibacterial analysis of the white jeringau extract lotion sample formula I, formula II and formula III against Staphylococcus aureus bacteria using the Kirby-bauer diffusion method showed the results of the inhibition zone diameter, namely in formula I the average inhibition zone formed was 11 .50 mm, in formula II it is 13.61 mm and in formula III it is 14.50 mm. According to Davis and Stout (1971) the inhibitory response by active ingredients is grouped into 4 categories, namely weak activity (≤ 5 mm), moderate (5-10 mm), strong (10-20 mm), and very strong (≥ 20 mm). ). Based on this classification, white jeringau extract lotion formula I, formula II and formula III are categorized as strong. Formula I had the best inhibitory response because the concentration of the extract was the smallest and had a strong category of inhibition compared to formula II and formula III which had a higher concentration and had the same inhibitory power. the results of statistical test analysis using the Kruskal Walis test obtained p value = 0.000 0.05 and it was concluded that there were differences in the white jeringau rhizome lotion formula I, II, and III in inhibiting the growth of Staphylococcus aureus bacteria.Â

Stressing environmental conditions in the “petrified forest” from the Mata Sequence in the Triassic context of the Paraná Basin

This study deals with the Piscina Outcrop, a Rhaetic reddish conglomeratic sandstone containing silicified logs which corresponds to the Mata Sequence in the southernmost Brazilian Paraná Basin. We performed ground-penetrating radar (GPR) analysis and the results ratified previous sequence stratigraphy analysis indicating that these deposits correspond to architectural elements exclusively related with the filling processes of fluvial channels. The erosive unconformity identified at the boundary between the Mata Sequence and the underlying rock packages could represent a considerable depositional hiatus. The integration of the GPR results with sedimentological and paleovertebrate data from a nearby outcrop at slightly lower topographic level indicated that the layer with the fossil woods is superimposed through an erosive unconformity to the stratigraphic levels corresponding to the Hyperodapedon Assemblage Zone of Carnian age from the basal portion of the Candelária Sequence. The wood assemblage was composed exclusively of araucarian coniferous stems identified as Agathoxylon (cf. Agathoxylon). The wood growth patterns were mainly characterized by woods showing indistinct growth rings, with latewood mostly restricted to one cell in each ring, suggesting weak seasonality and short-term, periodic droughts. Rare specimens with absent growth rings were also present. Oscillations in growth ring width and the common occurrence of false rings were likely linked to plant exposure to climatic instability. Anatomical evidence pointed to active biochemical responses to intense and extensive biological attack of fungi and arthropods. The dominant presence of carbon in the elemental composition of a dark substance filling many tracheid lumens suggested a very likely affinity with polyphenol remnants in biochemical barriers. The set of wood signatures seems to be linked to regional stressing conditions rather than to the paleolatitudinal location when compared to other key South American basins during the Rhaetic. An allochthonous taphocoenosis is the most likely taphonomic interpretation for this wood assemblage. The logs were probably incorporated into the stream through the collapse of riparian areas and buried in the fluvial channel by high-energy flows after biotic and abiotic decay processes during lifetime and secondarily through exposition before entombment in a river channel.

Emerging carbonate anion intercalated- ZnCr-layered double hydroxide/vanadium carbide nanocomposite: A electrochemical sensor for diethofencarb fungicide monitoring

Diethofencarb (DFC) is widely used in agriculture to fight against plant fungal attacks and enhance food crop production. On the other hand, the National food safety standard has set the overall maximum residual limit of DFC to be 1 mg/kg. Hence it becomes essential to limit their usage, and it is vital to quantify the amount of DFC present in real–life samples to safeguard the health and environmental well-being. Here, we introduce a simple hydrothermal procedure for preparing vanadium carbide (VC) anchored by ZnCr-LDH. The sustainably designed electrochemical sensor for the detection of DFC portrayed high electro-active surface area, conductivity, rapid-electron transport ratio, and high ion diffusion parameters. The obtained structural and morphological information confirms the enriched electrochemical activity of the ZnCr-LDH/VC/SPCE towards DFC. The ZnCr-LDH/VC/SPCE electrode has displayed exceptional characteristics with DPV resulting in a vast linear response (0.01–228 μM), and lower LOD (2 nM) with high sensitivity. Real-sample analysis was carried out to demonstrate the specificity of the electrode with an acceptable recovery in both water (±98.75–99.70%) and tomato (±98.00–99.75%) samples.

Characterization and transcriptomic analysis of a native fungal pathogen against the rice pest Nilaparvata lugens.

The brown planthopper (BPH), Nilaparvata lugens, is one of the most destructive pests of rice. Given the threats posed by insecticide resistance to its control, eco-friendly strategies based on microbial pathogens emerged as a promising biocontrol alternative. In the present study, we isolated a native fungal pathogen against BPH from infected BPH cadavers and preliminarily identified as a strain of Aspergillus fumigatus based on morphological and molecular methods. Laboratory bioassay revealed that this fungal strain was highly virulent to BPH both at nymphal and adult stages, with the median lethal times (LT50) of 7.5 and 5.8 days under high conidial concentration of 1 × 109 conidia mL-1. A genome-wide view of gene expressions in BPH against fungal attack was analyzed by transcriptomic sequencing and consequently a large number of differentially expressed genes that mainly involved in host immune defense and cell detoxification were found. RNAi-mediated knockdown of an upregulated gene encoding a serine protease (NlSPN) could cause a significant decrease in BPH survival. Combination of dsRNA injection and fungal infection showed an additive effect on BPH mortality, which provided clues to develop new pest management strategies against BPH.

The Effect of Road Conditions on Acacia mangium Timber Hauling Performance

The quality of timber could be affected by timber hauling, primarily when it remained in the forest and became vulnerable to pests and fungi attacks. Additionally, road conditions could also influence the slickness of hauling. Therefore, this study aimed to identify the effect of road conditions on hauling performance, cost, and soil deterioration. This research analyzed four types of road conditions in Acacia mangium plantations in West Java and Banten, including dry, wet, uphill, and downhill roads. The results indicated that the average hauling performance of 6.604 m3km/hour on the uphill road was the least among all road types. The uphill soil road had the highest average hauling cost of 30,685 IDR/m3km and the deepest average rut of 17.503 cm compared to others. These results would provide better information on low-cost and environmentally friendly timber hauling productivity.

Molecular Detection of Fusarium species infected Corn in Kurdistan region-Iraq

Corn or Maize product is regarded as one of the essential products in the world and stands third product after the rice and wheat crops. Different fungal pathogens attack corn plants; one of them is ear rot, brought on by Fusarium species and whose occurrence is primarily influenced by environmental factors. In order to isolate and identify Fusarium species from corn plants and their prevalence, 50 samples of corn were collected during September, October, and November of 2021 from 30 corn fields in 14 regions of different places in the Kurdistan region of Iraq. From all samples, 39 isolates of Fusarium were detected and based on morphological characteristics, six other species of Fusarium were identified, namely F. verticillioides (33.34%), F. proliferatum (25.64%), F. oxysporum (12.82%), F. incarnatum and F. equiseti (10.25% each), then F. fujikuroi (7.7%). The most prevalent species was F. verticillioides which was isolated from seven corn fields and significantly higher than all other isolated species. All Fusarium isolates were also molecularly identified depending on amplifying the internal transcribed spacer (ITS) universal region using forward ITS1 and reverse ITS4 primers and indicated DNA fragments ranged from 550 to 570 bp. The PCR fragments of the amplified ITS region were sequenced, aligned and registered in NCBI GeneBank with specified accession numbers. The phylogenetic tree and all analyzes were performed using the MEGA program version 11.0.13. The current study concluded that the corn fields in the Kurdistan region are infected with different Fusarium species, and the most common species is F. verticillioides. As well as the Fusarium species in the Kurdistan region have close evolutionary history to the same species in other countries. Thus, the study recommends more research to investigate the occurrence of toxigenic Fusarium species associated with cereal grains in the region.

Dual RNA-Seq Profiling Unveils Mycoparasitic Activities of Trichoderma atroviride against Haploid Armillaria ostoyae in Antagonistic Interaction Assays.

Armillaria ostoyae, a species among the destructive forest pathogens from the genus Armillaria, causes root rot disease on woody plants worldwide. Efficient control measures to limit the growth and impact of this severe underground pathogen are under investigation. In a previous study, a new soilborne fungal isolate, Trichoderma atroviride SZMC 24276 (TA), exhibited high antagonistic efficacy, which suggested that it could be utilized as a biocontrol agent. The dual culture assay results indicated that the haploid A. ostoyae-derivative SZMC 23085 (AO) (C18/9) is highly susceptible to the mycelial invasion of TA. In the present study, we analyzed the transcriptome of AO and that of TA in in vitro dual culture assays to test the molecular arsenal of Trichoderma antagonism and the defense mechanisms of Armillaria. We conducted time-course analysis and functional annotation and analyzed enriched pathways and differentially expressed genes including biocontrol-related candidate genes from TA and defense-related candidate genes from AO. The results indicated that TA deployed several biocontrol mechanisms when confronted with AO. In response, AO initiated multiple defense mechanisms to protect against the fungal attack. To our knowledge, the present study offers the first transcriptome analysis of a biocontrol fungus attacking AO. Overall, this study provides insights that aid the further exploration of plant pathogen-biocontrol agent interaction mechanisms. IMPORTANCE Armillaria species can survive for decades in the soil on dead woody debris, develop rapidly under favorable conditions, and harmfully infect newly planted forests. Our previous study found Trichoderma atroviride to be highly effective in controlling Armillaria growth; therefore, our current work explored the molecular mechanisms that might play a key role in Trichoderma-Armillaria interactions. Direct confrontation assays combined with time course-based dual transcriptome analysis provided a reliable system for uncovering the interactive molecular dynamics between the fungal plant pathogen and its mycoparasitic partner. Furthermore, using a haploid Armillaria isolate allowed us to survey the deadly prey-invading activities of the mycoparasite and the ultimate defensive strategies of its prey. Our current study provides detailed insights into the essential genes and mechanisms involved in Armillaria defense against Trichoderma and the genes potentially involved in the efficiency of Trichoderma to control Armillaria. In addition, using a sensitive haploid Armillaria strain (C18/9), with its complete genome data already available, also offers the opportunity to test possible variable molecular responses of Armillaria ostoyae toward diverse Trichoderma isolates with various biocontrol abilities. Initial molecular tests of the dual interactions may soon help to develop a targeted biocontrol intervention with mycoparasites against plant pathogens.

Effectiveness of papaya seed (Carica papaya L) solution against fungal prevalence and hatching power of koi carp (Cyprinus carpio L) eggs

One of the causes of the low production of koi carp seeds is fungal attack during the egg-hatching period, so natural treatments need to be carried out, including the use of papaya seeds. Papaya seeds contain antifungal compounds in the form of tannins, flavonoids, saponins, and alkaloids. The purpose of this study was to determine the effective dose of papaya seed solution in reducing the prevalence of the fungus and increasing the hatchability of koi goldfish eggs. This study was designed using a completely randomized design, which consisted of 5 treatments with 4 replications each. The treatment tested was papaya seed solution with treatment doses A=control, B=125 mg L-1, C=150 mg L-1, D=175 mgL-1, and E=200 mg L-1. Variables measured included the prevalence of the fungus, egg hatchability, observation of the fungus, hatching time, and water quality. The results showed that treatment with 125 mg L-1 of papaya seed solution reduced the prevalence of the fungus by 32.5% and resulted in the highest egg hatchability of 67.5%. The high hatchability of eggs is due to the presence of antifungal compounds in the form of flavonoids, saponins, tannins, and karpain contained in papaya seeds which provide protection for eggs against fungal infections so that eggs can hatch properly. The best dose of papaya seed solution to prevent fungal infection in koi carp eggs obtained at 200 mg L-1, 11.25%.