Atomic Force Microscopy Research Articles

Polydopamine-Mediated Antimicrobial Lipopeptide Surface Coating for Medical Devices.

Biofilm formation on medical implants such as catheters is a major issue which needs to be addressed as it leads to severe health care associated infections. This study explored the design and synthesis of a polydopamine-lipopeptide based antimicrobial coating. The coating was used to modify the surface of Ultrathane Catheters. The lipopeptide SL1.15 with an N-terminal cysteine was covalently conjugated to the polydopamine modified catheters via a Michael addition reaction between the thiol moiety in the peptide and the aromatic ring in the polydopamine layer. The immobilization of the peptide on the polydopamine coated catheters was confirmed using water contact angle, X-ray photoelectron spectroscopy, atomic force microscopy, and scanning electron microscopy (SEM). The antimicrobial activity of the coated catheters investigated using drug resistant and clinical strains of Gram-positive (MRSA and S. aureus) and Gram-negative (E. coli, A. baumannii, and P. aeruginosa) bacteria revealed that lipopeptide immobilization inhibited >90% bacterial adhesion to the catheter surface. Additionally, biofilm assays against MRSA and E. coli revealed that the lipopeptide immobilized catheters inhibited >85% bacterial growth after 1 week incubation. Finally, the cytotoxicity profile of the catheters using the human dermal fibroblast, and the human embryonic kidney cell lines demonstrated that the polydopamine-lipopeptide coating was not toxic after 72 h incubation.

Ultrasonic Production of Chitosan Nanoparticles and Their Application Against Colletotrichum gloeosporioides Present in the Ataulfo Mango.

In Mexico, the Ataulfo mango crop faces significant challenges due to anthracnose, a disease caused by the fungus Colletotrichum gloeosporioides. The need to use eco-friendly fungicides is crucial to avoid the use of harmful synthetic chemicals. This study aimed to prepare chitosan nanoparticles through a simple and effective ultrasound-assisted top-down method, with high antifungal efficiency. The nanoparticles were prepared from chitosan (DD = 85%, MW = 553 kDa) and Tween 20 under constant sonication. The formation of the nanoparticles was initially confirmed by Fourier-transform infrared (FTIR) spectroscopy; and their physicochemical properties were subsequently characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The antifungal potential of the chitosan nanoparticles against the phytopathogen Colletotrichum gloeosporioides was evaluated with isolated fungi obtained directly from mango tissues showing anthracnose symptoms in the state of Guerrero, Mexico. The fungus was identified through SEM imaging, showing a regular and smooth conidial layer, with cylindrical shape (r = 2 µm, h = 10 µm). In vitro tests were conducted with three different concentrations of chitosan nanoparticles to assess their inhibitory effects. After seven days of incubation, a maximum inhibition rate of 97% was observed with the 0.5% nanoparticle solution, corresponding to a fungal growth rate of 0.008 cm/h. At this time, the control mycelial growth was 7 cm, while the treated sample reached a radius of 0.55 mm. These results demonstrated the antifungal effect of the nanoparticles on the membrane and cell wall of the fungus, suggesting that their composition could induce a resistance response. The inhibitory effect was also influenced by the particle size (30 nm), as the small size facilitated penetration into fungal cells. Consequently, the parent compound could be formulated and applied as a natural antifungal agent in nanoparticle form to enhance its activity. The method described in this study offers a viable alternative for the preparation of chitosan nanoparticles, by avoiding the use of toxic reagents.

Effect of a novel irrigation regimen and root canal filling material versus conventional endodontic protocols on dentin wettability.

The purpose of this study was to compare the effect of different irrigation regimens on the dentin wettability of root canal sealers. The occlusal surfaces of human molar teeth (N = 90) were removed, polished, and divided into three groups (n = 30) based on the irrigation regimen: control group (SAL), standard irrigation group (NES), and test group (ODC). Each group was randomly divided into three subgroups according to the root canal sealer: AH Plus (AHP), Total Fill BC Sealer HiFlow (TOT), and OdneFill (ODF). The contact angle was determined using the sessile drop technique. The pendant droplet method assessed the work of adhesion. Surface roughness was measured using atomic force microscopy. Data were analyzed using non-parametric tests (p < .05). ODC-ODF showed significantly lower contact angle (34.80°) than ODC-AHP (66.53°, p < .001) and ODC-TOT (85.72°, p < .001). In NES, no significant difference was found between ODF and AHP (p > .05) while both groups presented significantly lower results than TOT (p < .001, p < .001, respectively). In SAL, the difference between TOT (92.84°) and AHP (83.24°) was insignificant (p > .05), whereas ODF presented significantly lower results compared to both (p < .001, p < .001, respectively). Surface roughness was lowest in ODC (31.54nm), followed by SAL (62.30nm) and NES (72.02 nms) which was significantly (p = 0.006) higher than ODC, whereas the difference between SAL and NES was insignificant (p > .05). This study highlights the wettability of a new root canal sealer and the effect of a new irrigation activation system on the wettability of different root canal sealers. OdneFill showed superior wettability compared to other sealers while exhibiting a synergistic effect with OdneClean.

Inhibitory Potential of N-Methyl Formanilide on Mild Steel Corrosion in Sulfuric Acid: Quantum Chemical and Experimental Perspectives

Technological progress has led to increased use of metals and alloys such as aluminum, brass, bronze and mild steel. While mild steel is favoured for its availability, low cost and excellent mechanical properties, it is prone to corrosion. This study aims to reduce the corrosion of mild steel in sulfuric acid using N-methyl formanilide (NMF) as an inhibitor. The effectiveness of NMF was evaluated using gravimetric method (weight loss) and electrochemical impedance spectroscopy (EIS). Surface analyses were conducted using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The study examined the performance of NMF at different temperatures (298 K to 338 K) and varying inhibitor concentrations. The results indicated that the percentage inhibition efficiency (%IE) of NMF increased with higher concentration but decreased with temperature. The NMF formed a protective layer on mild steel through physical adsorption, which was confirmed by El-Awady adsorption isotherm and comparing it with other adsorption models. The kinetic and thermodynamic studies were also performed, with activation energy (Ea) and adsorption free energy (ΔG°ads) being calculated. These findings were further validated using the AM1 quantum mechanical method, revealing the promising results for the investigation.

Multi-frequency power ultrasound (MFPU) pretreatment of crayfish (Procambarus clarkii): Effect on the enzymatic hydrolysis process and subsequent Maillard reaction

Crayfish, as a new consumer trend, has become one of the most popular freshwater aquatic foods in China, and its processed product output has been increasing year by year. In this study, the effect of multi-frequency power ultrasound (MFPU) pretreatment in various working modes including mono-, dual- and tri-frequency on the enzymatic hydrolysis and Maillard reaction of crayfish was investigated. Additionally, the underlying mechanism was also explored. Results showed that the degree of hydrolysis (DH) of crayfish was 23.89 %, while it increased to 40.78 % after MFPU pretreatment at 20/40 kHz dual-frequency, indicating that MFPU pretreatment significantly (p < 0.05) enhanced the enzymatic hydrolysis of crayfish. The crayfish protein after MFPU pretreatment exhibited a decrease in α-helix and increase in β-fold content, and the occurrence in the unfolding of the protein structure and alteration of tertiary structure. According to scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses, the MFPU pretreatment resulted in the fragmentation of crayfish protein. During the analyses of subsequent Maillard reaction, the composition and quantity of volatiles detected by the electronic nose and GC–MS indicated that MFPU pretreatment enhanced flavor of the Maillard reaction products. In conclusion, MFPU pretreatment is a promising technology for improving the degree of hydrolysis of crayfish protein and enhancing the flavor of Maillard reaction products.

Investigation of Corrosion Inhibition of Carbon Steel by Using Natural Iraqi Plum Tree Gum in a Saline Medium

In response to the growing interest in green chemistry and the adoption of environmentally friendly and cost-effective compounds in industrial and agricultural applications, this study focuses on exploring the potential of natural compounds. Specifically, the research investigates the corrosion inhibitory properties of Iraqi plum tree gum. The natural gum is characterized using Fourier transform infrared spectroscopy to identify its functional groups and atomic force microscopy (AFM) for further analysis. The electrochemical polarization technique was used to study corrosion measurements for carbon steel (C.S) in saline solution and in the presence of the inhibitor (Plum Tree Gum) in different concentration solutions. The findings revealed a positive correlation between the concentration of plum tree gum and the efficiency of the inhibitor, indicating that higher concentrations of the gum result in increased inhibitory effectiveness.

Investigating the influence of RF power on the surface morphological and optical properties of sputtered TiO2 thin films

Thin films of titanium dioxide (TiO2), with thicknesses ranging from 105 to 231 nm, were deposited on glass substrates using radio-frequency (RF) magnetron sputtering in an argon atmosphere at four distinct RF power levels: 40, 70, 100, and 130 W, with the deposition time kept constant. The crystalline structure, surface morphology and optical and semiconductor properties of the obtained films were analyzed using X-ray diffraction (XRD), Atomic Force Microscopy (AFM) and UV–visible transmittance spectroscopy. These analyses revealed that the crystallinity of the films improves with increasing RF power, corresponding to an increase in film thickness. Consequently, the samples transition from poorly crystalline or amorphous structure to a monocrystalline rutile phase with a (110) texture. However, at the highest RF power studied, this texture is partially disrupted by the formation of nanocrystals with different orientations. The surface roughness exhibited multifractal characteristics, with complexity systematically decreasing and surface stiffness reducing as RF power increased. Refractive indices and optical band gap energies were determined using the Swanepoel and Tauc plot methods, respectively. The films exhibited a notable increase in the refractive index and a decrease in the optical band gap, from 3.81 eV to 3.52 eV, as the RF power was increased. This underscores the influence of RF power on the optical and semiconductor properties of TiO2 films.

Evaluation of AlN insertion layer on the properties of heterogeneous integrated Ga2O3 films on sapphire

Integration of gallium oxide (Ga2O3) with highly thermal conductive AlN/sapphire substrate is more effective to dissipate heat in the Ga2O3-based devices. In this work, the properties of Ga2O3 films grown on sapphire and AlN/sapphire substrates via MOCVD were both examined via various experimental methods. The X-ray diffraction (XRD) analysis showed good crystallinity and different orientations of Ga2O3 and AlN thin films. The absorption properties and band gaps were extracted from UV/Vis spectra. The atomic force microscopy (AFM) scanning images showed smooth Ga2O3 surfaces on sapphire and AlN/sapphire substrates (RMSs of 2.4 nm and 4.8 nm, respectively). The scanning electron microscopy (SEM) highlighted well-defined grains of Ga2O3 and distinct boundaries of both heterostructures. X-ray photoelectron spectroscopy (XPS) analysis depicted the distributions of various components throughout the films. Finally, by using the time-domain thermoreflectance (TDTR) method, the thermal conductivity and the thermal boundary conductivity of Ga2O3 without AlN interlayer were found to be 3.1 W/(m·K) and 70.1 MW/(m2·K) respectively. By comparison, adding AlN interlayer made the thermal conductivity and thermal boundary conductivity rise to 3.3 W/(m·K) and 111.5 MW/(m2·K) respectively. These findings have demonstrated the high-quality Ga2O3/AlN integration and good heat dissipation provided by AlN interlayer, opening up new prospects for Ga2O3/AlN devices in the future.

Intelligent Nanomaterial Image Characterizations – A Comprehensive Review on AI Techniques that Power the Present and Drive the Future of Nanoscience

AbstractArtificial Intelligence (AI) is pivotal in advancing science, including nanomaterial studies. This review explores AI‐based image processing in nanoscience, focusing on algorithms to enhance characterization results from instruments like scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, atomic force microscopy etc. It addresses the significance of AI in nanoscience, challenges in advancing AI‐based image processing for nano material characterization, and AI's role in structural analysis, property prediction, deriving structure‐property relations, dataset augmentation, and improving model robustness. Key AI techniques such as Graph Neural Networks, adversarial training, transfer learning, generative models, attention mechanisms, and federated learning are highlighted for their contributions to nano science studies. The review concludes by outlining persisting challenges and thrust areas for future research, aiming to propel nanoscience with AI. This comprehensive analysis underscores the importance of AI‐powered image processing in nanomaterial characterization, offering valuable insights for researchers.

Using natural starch granules to disperse solid beeswax into micron-sized droplets in emulsion

Use of beeswax together with starch to manufacture emulsion for fruit preservation has attracted wide attention in food packaging. In this paper, esterified starch (M-PS) granules prepared from natural potato starch were used to replace nanocrystals to prepare beeswax emulsion. The swelling property of M-PS granules was used to solve the problem of uneven dispersion of beeswax. Atomic force microscope (AFM) images showed that the network gel structure formed by M-PS granules limited the movement of beeswax droplets, and the droplet size was <1.0 μm. When the beeswax emulsion was added to the starch paste, the resulting starch-beeswax composite emulsion had a stable gel structure. Bananas were coated with the composite emulsion. After 7 days of storage, compared with the test data of bare bananas, the weight loss rate decreased by 42 %, the titratable acidity increased by 21 %, and the vitamin C was higher by 20 % of coated bananas. The formed coating effectively inhibited the decline of banana quality.

Application of active piezoresistive cantilevers in high-eigenmode surface imaging

Abstract One of the most important limitations of the atomic force microscopy (AFM) is scanning speed, whose high values are required for contemporary high-resolution, long-range diagnostic applications. The measurement bandwidth of an AFM depends on several factors, but usually results from the time constant of the oscillating cantilever, which is correlated with its resonance frequency and quality factor. We propose a method to overcome this problem by performing the surface measurements when the cantilever is vibrating in higher eigenmodes. In this paper we demonstrate the application of active piezoresistive cantilevers operating in this mode. The active piezoresistive cantilever comprises a piezoresistive deflection sensor, a deflection actuator and a nanotip. It is a complete micro-electro-mechanical system (MEMS), ensuring the highest reliability of cantilever vibration control and detection. Higher eigenmode operations are usually difficult to implement as they usually result in lower deflection and lower sensitivity of the probe vibration deflection. Here we present an experimental modification of the structure of an active piezoresistive cantilever using focused ion beam (FIB) machining that mitigates both weaknesses. This has enabled the cantilever to scan the surface at a scanning rate of 10 lines/s with a maximum speed of 500 μm/s and a data acquisition rate of 10 kS/s, when the probe is vibrating at 380 kHz in the second eigenmode. We also describe a traceable calibration routine (based on analysis of the response of the piezoresistive detector, the output of the HeNe interferometer and precise control of the deflection actuator), together with the cantilever modification process and the development of the measurement setup. We show measurement results of dedicated calibration samples and silicon carbide crystal lattice references.&amp;#xD;

Probing Nanoscale Charge Transport Mechanisms in Quasi-2D Halide Perovskites for Photovoltaic Applications.

Quasi-2D layered halide perovskites (quasi-2DLPs) have emerged as promising materials for photovoltaic (PV) applications owing to their advantageous bandgap for absorbing visible light and the improved stability they enable. Their charge transport mechanism is heavily influenced by the grain orientation of their crystals as well as their nanostructures, such as grain boundaries (GBs) and edge states─the formation of which is inevitable in polycrystalline quasi-2DLP thin films. Despite their importance, the impact of these features on charge transport remains unexplored. In this study, we conduct a detailed investigation on polycrystalline quasi-2DLP thin films and devices, carefully analyzing how grain orientation and nanostructures influence charge transport. Employing nondestructive atomic force microscopy (AFM) topography, along with transient absorption spectroscopy (TAS) and grazing-incidence wide-angle X-ray scattering (GIWAXS), we obtained significant insights regarding the phase purity, crystallographic information, and morphologies of these films. Moreover, our systematic investigation using AFM-based techniques, including Kelvin probe force microscopy (KPFM) and conductive AFM (c-AFM), elucidates the roles played by GBs and edge states in shaping charge transport behavior. In particular, the local band structure along the GBs and edge states within both vertical and parallel grains was found to selectively repel electrons and holes, thus facilitating charge carrier separation. These findings provide perspectives for the development of high-performance quasi-2DLP PV devices and highlight potential approaches that can leverage the intrinsic properties of quasi-2DLPs to advance the performance of perovskite solar cells.

Effect of protease hydrolysis on the structure of acidic heating-induced soy protein amyloid fibrils

The effectiveness of using amyloid fibrillation to improve the functional qualities of soy protein had drawn growing attention. However, the relationship between protein subunits and the structural polymorphism of soy protein-derived amyloid fibrils (SAFs) was not yet completely understood. In this study, soy protein subunits were hydrolyzed to different degrees according to the different action sites of different proteases (Pepsin, Papain and Alcalase). The impact of subunits on the amyloid fibrillation of soy protein was investigated through various techniques including atomic force microscopy, thioflavin T fluorescence, 1-anililo-naphthalene-8-sulfonate, and Fourier transform infrared spectrometer. The findings showed that the α and α’ subunits were associated with the formation of fibril branch chains. The degree of hydrolysis of β subunits was found to be proportional to the number of fibrils. The presence of the 11S component was identified as a necessary condition for the formation of long-rigid fibrils. Furthermore, enzymatic hydrolysis unfolded the protein structure, exposing hydrophobic groups, loosening the protein structure, and altering the proportion of parallel and antiparallel β-sheet structures. This promoted the formation of amyloid fibrils and accelerated the development of stable SAFs gel. This study advances the knowledge of the function of subunits in amyloid fibrillation.

Imaging Ferroelastic Domain Walls in Hybrid Improper Ferroelectric Sr3Sn2O7.

We combined synchrotron-based near field infrared spectroscopy and atomic force microscopy to image the properties of ferroelastic domain walls in Sr3Sn2O7. Although frequency shifts at the walls are near the limit of our sensitivity, we can confirm semiconducting rather than metallic character and widths between 20 and 60 nm. The latter is significantly narrower than in other hybrid improper ferroelectrics like Ca3Ti2O7. We attribute this trend to the softer lattice in Sr3Sn2O7, which may enable the octahedral tilt and rotation order parameters to evolve more quickly across the wall without significantly increased strain. These findings are crucial for the understanding of phononic properties at interfaces and the development of domain wall-based devices.

Variability in individual native fibrin fiber mechanics

Fibrin fibers are important structural elements in blood coagulation. They form a mesh network that acts as a scaffold and imparts mechanical strength to the clot. A review of published work measuring the mechanics of fibrin fibers reveals a range of values for fiber extensibility. This study investigates fibrinogen concentration as a variable responsible for variability in fibrin mechanics. It expands previous work to describe the modulus, strain hardening, extensibility, and the force required for fiber failure when fibers are formed with different fibrinogen concentrations using lateral force atomic force microscopy. Analysis of the mechanical properties showed fibers formed from 1 mg ml-1and 2 mg ml-1fibrinogen had significantly different mechanical properties. To help clarify our findings we developed two behavior profiles to describe individual fiber mechanics. The first describes a fiber with low initial modulus and high extensible, that undergoes significant strain hardening, and has moderate strength. Most fibers formed with 1 mg ml-1fibrinogen had this behavior profile. The second profile describes a fiber with a high initial modulus, minimal strain hardening, high strength, and low extensibility. Most fibrin fibers formed with 2 mg ml-1fibrinogen were described by this second profile. In conclusion, we see a range of behaviors from fibers formed from native fibrinogen molecules but various fibrinogen concentrations. Potential differences in fiber formation are investigated with SEM. It is likely this range of behaviors also occursin vivo. Understanding the variability in mechanical properties could contribute to a deeper understanding of pathophysiology of coagulative disorders.

Recent Progress of Imaging Chemical Bonds by Scanning Probe Microscopy: A Review.

In the past decades, the invention of scanning probe microscopy (SPM) as the versatile surface-based characterization of organic molecules has triggered significant interest throughout multidisciplinary fields. In particular, the bond-resolved imaging acquired by SPM techniques has extended its fundamental function of not only unraveling the chemical structure but also allowing us to resolve the structure-property relationship. Here, we present a systematical review on the history of chemical bonds imaged by means of noncontact atomic force microscopy (nc-AFM) and bond-resolved scanning tunneling microscopy (BR-STM) techniques. We first summarize the advancement of real-space imaging of covalent bonds and the investigation of intermolecular noncovalent bonds. Beyond the bond imaging, we also highlight the applications of the bond-resolved SPM techniques such as on-surface synthesis, the determination of the reaction pathway, the identification of molecular configurations and unknown products, and the generation of artificial molecules created via tip manipulation. Lastly, we discuss the current status of SPM techniques and highlight several key technical challenges that must be solved in the coming years. In comparison to the existing reviews, this work invokes researchers from surface science, chemistry, condensed matter physics, and theoretical physics to uncover the bond-resolved SPM technique as an emerging tool in exploiting the molecule/surface system and their future applications.

Protein Quakes in Redox Metalloenzymes: Clues to Molecular Enzyme Conductivity Triggered by Binding of Small Substrate Molecules.

Multicentre redox metalloproteins undergo conformational changes on electrochemical surfaces, or on enzyme substrate binding. The two-centre copper enzymes, laccase (Type I and TypeII/III Cu) and nitrite reductase (CuNIR) (Type I and Type II Cu) are examples. With some exceptions, these enzymes show no non-turnover voltammetry on Au(111)-surfaces modified by thiol based self-assembled molecular monolayers, but dioxygen or nitrite substrate triggers strong electrocatalytic signals. Scanning tunnelling microscopy also shows high conductivity only when dioxygen or nitrite is present. Atomic force microscopy shows constant CuNIR height but pronounced structural expansion in the electrocatalytic range on nitrite binding. We have recently offered a rationale, based on ab initio quantum chemical studies of water/nitrite substitution in a 740-atom CuNIR fragment. Presently we provide much more detailed structural assignment mapped to single-residue resolution. NO2 --binding induces both a 2 Å Cu-Cu distance increase, and pronounced frontier orbital delocalization strongly facilitating ET between the Cu regions. The conformational changes transmit from the catalytic Type II centre to the electron inlet Type I centre, via the His129-Cys130 ligands, and via Type I-Cys130 or Type I-His129 ending at Type II Asp92. The ET patterns are reflected in different atomic Mulliken charges in the water and nitrite CuNIR fragment.

Micro structures, Morphology and Optical Properties of Sb2O3: WO3, In2O3 Nanostructure Composite Thin Films

This work is concerned with the synthesis of two types of composites thin films (Sb2O3:WO3 and (Sb2O3:In2O3) with different concentrations (0.0,0.05,0.1, and 0.15). The prepared thin films are characterized with the use of the X-ray diffraction atomic force microscope AFM and UV-Vis–infrared spectrophotometer. The structural examination shows that both composite's thin films were polycrystalline with nano size with cubic phase as majority and orthorhombic phase as minority phase. The crystal size decreases from 34.6 to 24.7 and 21.7 nm for (Sb2O3:WO3) and (Sb2O3:In2O3) thin films, respectively. The average roughness shows non-regular growth by increasing the concentration of both oxides. The optical energy band gap shows a red shift for both types of nanostructure thin films, which populate these composited thin films for solar cell applications.

Sensing force gradients with cavity optomechanics while evading backaction

We study force-gradient sensing with a coherently driven mechanical resonator and phase-sensitive detection of motion through the two-tone backaction evading measurement of cavity optomechanics. The response of the optomechanical system, solved by numerical integration of the classical equations of motion, shows an extended region which is monotonic to changes in force gradient. We use Floquet theory to model the fluctuations, which rise only slightly above that of the usual backaction evading measurement in the presence of the mechanical drive. The monotonic response and minimal backaction are advantageous for applications such as atomic force microscopy. Published by the American Physical Society 2024

Genosensor based on polypyrrole and dendrimer-coated gold nanoparticles for human papillomavirus detection

Human Papillomavirus (HPV) is an often asymptomatic widespread sexually transmitted infection responsible for causing various health issues. Low-risk HPV primarily causes genital warts. High-risk HPV types are associated with several cancers, including cervical, anal, and oropharyngeal cancers, posing significant health risks. In this work, we developed an electrochemical biosensor for the detection and differentiation of HPV genotypes based on electropolymerized polypyrrole (PPy) and PAMAM dendrimer-coated gold nanoparticles (PAMAM-AuNPs) for the immobilization of a DNA probe for detecting different HPV genotypes. Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and atomic force microscopy (AFM) were used to characterize the biosensor. AFM analysis revealed varied topographic surfaces associated with the increased peaks concerning the biosensor and against patient samples. Electrochemical responses indicated that the genosensor could detect HPV using plasmid (HPV 6, 16, 18, 31, and 33) and cDNA samples (HPV 6, 18, and 31) from infected patients. Different electrochemical profiles were obtained between high-risk and low-risk genotypes. The sensor presented an excellent analytical performance, presenting a lower LOD of 0.04 pg.µL−1 and 0.34 pg.µL−1 for plasmidial and cDNA samples, respectively. Electrochemical analysis pointed out the ability of the developed genosensor platform to differentiate the HPV genotypes. The proposed biosensor is a promising tool for detecting and monitoring HPV and related diseases such as cervical cancer.