Atomic Force Microscopy Measurements Research Articles

Onset and microscopic origin of resistive random-access memory characteristics on low-cost thermally treated mixed phase CuxO (x = 1,2) on Cu sheet

We demonstrated the resistive random-access memory (RRAM) characteristics in cost-efficient, single-step, and in-situ grown nanostructured mixed-phase CuxO (x = 1, 2) thin films, on a commercially available Cu sheet, fabricated using thermal treatment under ambient conditions. The scanning electron microscopy (SEM) and atomic force microscopy (AFM) measurements explain the surface morphology of grown mixed-phase CuxO thin film with substrate imprints. Fourier-transform Infrared spectroscopy confirmed the mixed phase of Cu2O and CuO of synthesized thin films. The fabricated Al/CuxO/Cu RRAM device showed bipolar digital resistive switching followed by analog resistive switching. The device showed a fast-switching speed of 250 ms, high endurance durability for 2500 cycles, and better retention of 103 s, respectively. The interconnected CuxO with Cu sheet provides efficient charge carrier migration from the bottom electrode to the active layer. The formed defect and trapped site are responsible for the resistive switching behavior. Thus, the present study provides a way to harness the potential of RRAM on either thermally treated Cu sheets or realizing a Cu thin film followed by low-temperature annealing, which can easily be integrated into existing electronic devices for data storage applications.

Hypoxic extracellular vesicles from hiPSCs protect cardiomyocytes from oxidative damage by transferring antioxidant proteins and enhancing Akt/Erk/NRF2 signaling

BackgroundStem cell-derived extracellular vesicles (EVs) are an emerging class of therapeutics with excellent biocompatibility, bioactivity and pro-regenerative capacity. One of the potential targets for EV-based medicines are cardiovascular diseases (CVD). In this work we used EVs derived from human induced pluripotent stem cells (hiPSCs; hiPS-EVs) cultured under different oxygen concentrations (21, 5 and 3% O2) to dissect the molecular mechanisms responsible for cardioprotection.MethodsEVs were isolated by ultrafiltration combined with size exclusion chromatography (UF + SEC), followed by characterization by nanoparticle tracking analysis, atomic force microscopy (AFM) and Western blot methods. Liquid chromatography and tandem mass spectrometry coupled with bioinformatic analyses were used to identify differentially enriched proteins in various oxygen conditions. We directly compared the cardioprotective effects of these EVs in an oxygen-glucose deprivation/reoxygenation (OGD/R) model of cardiomyocyte (CM) injury. Using advanced molecular biology, fluorescence microscopy, atomic force spectroscopy and bioinformatics techniques, we investigated intracellular signaling pathways involved in the regulation of cell survival, apoptosis and antioxidant response. The direct effect of EVs on NRF2-regulated signaling was evaluated in CMs following NRF2 inhibition with ML385.ResultsWe demonstrate that hiPS-EVs derived from physiological hypoxia at 5% O2 (EV-H5) exert enhanced cytoprotective function towards damaged CMs compared to EVs derived from other tested oxygen conditions (normoxia; EV-N and hypoxia 3% O2; EV-H3). This resulted from higher phosphorylation rates of Akt kinase in the recipient cells after transfer, modulation of AMPK activity and reduced apoptosis. Furthermore, we provide direct evidence for improved calcium signaling and sustained contractility in CMs treated with EV-H5 using AFM measurements. Mechanistically, our mass spectrometry and bioinformatics analyses revealed differentially enriched proteins in EV-H5 associated with the antioxidant pathway regulated by NRF2. In this regard, EV-H5 increased the nuclear translocation of NRF2 protein and enhanced its transcription in CMs upon OGD/R. In contrast, inhibition of NRF2 with ML385 abolished the protective effect of EVs on CMs.ConclusionsIn this work, we demonstrate a superior cardioprotective function of EV-H5 compared to EV-N and EV-H3. Such EVs were most effective in restoring redox balance in stressed CMs, preserving their contractile function and preventing cell death. Our data support the potential use of hiPS-EVs derived from physiological hypoxia, as cell-free therapeutics with regenerative properties for the treatment of cardiac diseases.

Poly(vinyl pyridine) coatings cross-linked with transition metal complexes as active layers for biosensors sensitive to protein adsorption and cell adhesion

The possibility of application of poly(4-vinyl pyridine) layers cross-linked with transition metal complexes as active layers in biomedical sensors was tested. The successful modification of the P4VP coating with CuBr2 or ZnBr2 was verified using time of flight - secondary ion mass spectrometry and X-ray photoelectron spectroscopy. The topography and wettability of the coatings were examined by using atomic force microscopy and water contact angles measurements, respectively. Tests of biological activity of coatings indicated strong protein adsorption, good biocompatibility, and no antimicrobial activity. The potential of the coatings to be used as active layers of biosensors was verified, by systematic impedance-based measurements, which showed the sensitivity of the P4VP:CuBr2 coatings to the presence of proteins and cells in different concentrations. The high selectivity of the coatings toward the defined analyte was confirmed by the specific antigen–antibody immunoreaction, and the possibility of in situ monitoring of protein adsorption and cell adhesion also for individual cells was presented. Finally, the conductive response of a bilayer system that mimics Organic Field Effect Transistor was shown. These results point to a great potential for both coatings to serve as active layers of sensitive and highly selective biosensors.

Discrete Element Method Simulation of Particulate Material Fracture Behavior on a Stretchable Single Filter Fiber with Additional Gas Flow

This study presents a comprehensive discrete element method (DEM) simulation approach for the stretching of a filter fiber with a separated polydisperse particle structure on top. For a realistic interaction between the fiber surface and the particles, the original surface of the polymer fiber was projected onto the surface of the fiber cylinder using surface imaging technologies (atomic force microscopy (AFM) and white-light interferometry). In addition, the adhesive forces between particle–fiber and particle–particle contacts were calibrated in the DEM domain using values from self-conducted AFM measurements. Fiber stretching was implemented by the linear motion of small periodic fiber elements. Discretization problems were resolved through studying the stretching of a fiber segment at the size of 8 mm. A critical fiber element length was discovered to be ≈100 μm for minimizing discretization dependencies during the cracking of the particle structure. The number and density of particle–particle contacts within the particle loading on the fiber were obtained at two different elongation rates. Effects such as densification of the particulate structure and increased detachment due to additional air flow were demonstrated.

Stability of bubble-particle hetero-coagulates accessed by atomic force microscopy to understand the froth flotation of agglomerating hydrophobic fines

The key microprocesses, which determine the efficiency in froth flotation are the formation and breakage of particle-bubble hetero-coagulates. Agglomeration can be used to increase the recovery of fine particles < 20 µm. Here the stability of hetero-coagulates consisting of agglomerates and gas bubble determines the process performance. Therefore, the stability of agglomerate-bubble hetero-coagulates was accessed by atomic force microscopy (AFM) on particle-laden gas bubbles, agglomerates and pristine gas bubbles without particles in the interface. The force and work of adhesion from AFM measurements were compared to the detaching force and the detaching energy that act on agglomerate-bubble and particle-bubble hetero-coagulates under turbulent conditions, similar to those in a flotation cell. This comparison provides the maximum size of agglomerates and single particles that can remain attached to the gas bubbles at a given energy dissipation rate. The results suggest that the size of agglomerates attached to gas bubbles can grow beyond the Kolmogorov length, which limits the size of agglomerates under turbulent conditions. The findings are supported by in-line probe images of agglomerate-bubble hetero-coagulates that were captured in an aerated stirred tank under turbulent conditions. It was further shown that the particle detachment from particle-laden bubbles is governed by the deformation of the underlying gas bubble and the local particle coverage.

Tuning the Topo-Morphological properties of ITO Films using Al-Ag interlayer for Low-Resistance Optoelectronics Devices

Indium tin oxide (ITO) is recently attracting intense attention for application as transparent conducting electrode in different optoelectronic devices including solar cells, liquid crystal displays and organic light emitting diodes. This is attributed to their high optical transmittance in the visible region and good electrical conductivity. In this work, surface topological-morphological (topo-morphological) and electrical properties of ITO based multilayer films with aluminum-silver (Al-Ag) metal interlayer (ITO/Al-Ag/ITO) are investigated after post annealing treatment at 300-500oC by atomic force microscopic (AFM), field emission scanning electron microscopy (FESEM), four-point probe and hall-effect techniques respectively. The ITO/Al-Ag/ITO films are deposited by direct current and radio frequency magnetron sputtering techniques on p-type Si at room temperature. The results showed a smooth surface topology by as-deposited film with films smoothness improving after post annealing treatment as analyzed by AFM method. Sharp crystallites peaks were obtained by all the films with smaller peaks diffusing and recombining to form larger films with increasing post-annealing temperature. The films root means square roughness increased as the temperature increases with film annealed at 500oC showing a superior and enhanced microstructure. Compared to as-deposited film, careful observation shows that surface morphology smoothness increased with increase in temperature with films annealed at 400oC and 500oC showing highest increasing surface smoothness pattern as determined by FESEM technique. Similarly, higher grain sizes are observed especially by films annealed at 400oC and 500oC due to the heat absorption which causes the particles to expand thereby narrowing the grain boundaries and subsequently improve the surface smoothness. These FESEM findings are consistent with AFM measurements confirming the high surface property and enhanced grain size with increasing post annealing temperature. The films exhibit decreased electrical resistivity and sheet resistance while carrier concentration and Hall mobility increased with increasing post annealing treatment indicating highest corresponding values of...

Interplay between photoinduced charge and energy transfer in manganese doped perovskite quantum dots.

A comprehensive study on the photo-excited relaxation dynamics in semiconducting perovskite quantum dots (PQDs) is pivotal in realizing their extensive potential for optoelectronics applications. Among different competing photoinduced relaxation kinetics, energy transfer and charge transfer (CT) in PQDs need special attention, as they often influence the device efficacy, particularly with the donor-acceptor hybrid architecture. In this work, we explore a detailed investigation into photoinduced CT dynamics in mixed halide undoped CsPb(Br/Cl)3 and Mn2+ doped CsPb(Br/Cl)3 PQDs with a quinone molecule, p-benzoquinone (BQ). The energy level alignment of undoped PQDs with BQ allows an efficient CT, whereas Mn2+ doping reduces the CT efficiency, experiencing a competition between energy transfer from host to dopant and CT to BQ. The conductive atomic force microscopy measurements unveil a direct correlation with the spectroscopic studies by showing a significant improvement in the conductance of undoped PQDs in the presence of BQ, while an inappreciable change is observed for doped PQDs. A much-reduced transition voltage and barrier height in the presence of BQ further validate faster CT for undoped PQD than the doped one. Furthermore, Mn2+ doping in PQDs is observed to enhance their stability, showing better air and thermal stability compared to their undoped counterparts. These results reveal that doping strategy can regulate the CT dynamics in these PQDs and increase their stability, which will be beneficial for the development of desired optoelectronic devices with long-term stability.

Effect of Solvent Composition on Non-DLVO Forces and Oriented Attachment of Zinc Oxide Nanoparticles.

Oriented attachment (OA) occurs when nanoparticles in solution align their crystallographic axes prior to colliding and subsequently fuse into single crystals. Traditional colloidal theories such as DLVO provide a framework for evaluating OA but fail to capture key particle interactions due to the atomistic details of both the crystal structure and the interfacial solution structure. Using zinc oxide as a model system, we investigated the effect of the solvent on short-ranged and long-ranged particle interactions and the resulting OA mechanism. In situ TEM imaging showed that ZnO nanocrystals in toluene undergo long-range attraction comparable to 1kT at separations of 10 nm and 3kT near particle contact. These observations were rationalized by considering non-DLVO interactions, namely, dipole-dipole forces and torques between the polar ZnO nanocrystals. Langevin dynamics simulations showed stronger interactions in toluene compared to methanol solvents, consistent with the experimental results. Concurrently, we performed atomic force microscopy measurements using ZnO-coated probes for the short-ranged interaction. Our data are relevant to another type of non-DLVO interaction, namely, the repulsive solvation force. Specifically, the solvation force was stronger in water compared to ethanol and methanol, due to the stronger hydrogen bonding and denser packing of water molecules at the interface. Our results highlight the importance of non-DLVO forces in a general framework for understanding and predicting particle aggregation and attachment.

Remotely Controlled Surface Charge Modulation of Magnetoelectric Nanogenerators for Swift and Efficient Drug Delivery.

We have developed a highly efficient technique of magnetically controlled swift loading and release of doxorubicin (DOX) drug using a magnetoelectric nanogenerator (MENG). Core-shell nanostructured MENG with a magnetostrictive core and piezoelectric shell act as field-responsive nanocarriers and possess the capability of field-triggered drug release in a cancerous environment. MENGs generate a surface electric dipole when subjected to a magnetic field due to the strain-mediated magnetoelectric effect. The capability of directional magnetic field-assisted modulation of the surface electrical dipole of MENG provides a mechanism to create/break ionic bonds with DOX molecules, which facilitates efficient drug attachment and on-demand swift detachment of the drug at a targeted site. The magnetic field-assisted drug-loading mechanism was minutely analyzed using spectrophotometry and Raman spectroscopy. The detailed time-dependent analysis of controlled drug release by the MENG under unidirectional and rotating magnetic field excitation was conducted using field-emission scanning electron microscopy, energy-dispersive X-ray, and atomic force microscopic measurements. In vitro, experiments validate the cytocompatibility and magnetically assisted on-demand and swift DOX drug delivery by the MENG near MCF-7 breast cancer cells, which results in a significant enhancement of cancer cell killing efficiency. A state-of-the-art experiment was performed to visualize the nanoscale magnetoelectric effect of MENG using off-axis electron holography under Lorentz conditions.

Exploring asphaltene aggregation: Model systems based on toluene-heptane mixtures

This work evaluates how chemical characteristics, such as polarity and aromaticity, can affect asphaltene aggregation. The asphaltene fraction was extracted from two different crude oils by precipitation in n-heptane, and these extracted asphaltenes were named A and B. Based on infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR) analyses, we found that asphaltenes B present greater aromaticity. According to X-ray photoelectron spectroscopy (XPS), asphaltene B showed higher heteroatom content. Model systems based on toluene/n-heptane/asphaltene (0.05 g/L) were prepared to evaluate the aggregation/precipitation of asphaltenes. Dynamic light scattering (DLS) analysis of aggregation kinetics revealed that aromatic asphaltenes with higher heteroatom content tend to form larger aggregates. Moreover, hydroxyl content exhibits a greater impact on aggregation compared to diffusivity. Furthermore, once the aggregates reach a critical size, the suspension stability is reduced, and the aggregates sediment. The atomic force microscopy (AFM) and DLS results revealed a wide range of particle size distribution. The larger clusters likely consisted of smaller aggregates that adhered together. Still, we highlight that the sizes of these aggregates determined by AFM are not directly comparable to the measurements obtained from DLS. The drying of the samples for the AFM measurements probably affects the asphaltene aggregation process. For this reason, the results obtained from the AFM and DLS techniques are not comparable.

Design of a vibration isolation platform for atomic force microscope based on flexural structure

Atomic force microscope (AFM) is a powerful instrument for nanoscale measurement in different environments. Since high-resolution AFM measurements require avoiding external vibration interference, bulky vibration isolation platforms are commonly applied, which is a limitation for in-situ AFM measurements in some environments with small space and limited loads. For high-resolution imaging without bulky external vibration isolation, this paper presents a vibration isolation method for AFM with its internal z-axis (vertical) actuators moving the AFM probe. A piezoelectric actuator was used for z-axis actuation, and a flexural structure with low stiffness was designed to guide the z-axis motion and achieve vibration isolation. The low stiffness mechanically isolated the probe from floor vibrations at high frequencies. The parameters of the flexural structure were determined theoretically, and its performance was analyzed through finite element method. Finally, the prototype of the platform was machined and its vibration isolation performance was experimentally tested. The experimental results indicate that the vibrational isolation effect of the designed flexural structure is increased by 51 % in the z-axis in the frequency range 0.1–300 Hz and above 900 Hz compared to the original AFM structure.

Study of charge transport in cesium lead bromide perovskite quantum dots and PCPDTBT composites: an application to photosensitive FETs

This work investigates the optical, structural, and photo-physical properties of PCPDTBT/cesium lead bromide (CsPbBr3) perovskite quantum dots (QDs) composite for optoelectronic devices. The composite was prepared by processing the PCPDTBT and CsPbBr3 QDs via the solution blending method. Incorporating CsPbBr3 QDs with different weight % (wt%) ratio in PCPDTBT influences its optoelectronic properties. UV–vis absorption spectroscopy, photoluminescence (PL), and atomic force microscopy measurements were used to analyze their optical and morphological properties. We observed that incorporating 4 wt% QDs in PCPDTBT enhanced its light absorption and charge transfer properties. Increased carrier lifetime for PCPDTBT/QDs (4 wt%) was observed from PL decay measurements. Further, we fabricated the field effect transistors (FETs) of pristine PCPDTBT and PCPDTBT/CsPbBr3 QDs composite (4 wt%) to study their electronic and charge transfer features. Significant variation in source-to-drain current (IDS) and carrier mobility has been observed. A substantial increased output current was observed for composite FET than pristine PCPDTBT-based FET due to charge transfer from QDs to PCPDTBT. Both PCPDTBT and PCPDTBT/CsPbBr3 QDs-based FET show enhanced current with illumination, which could be attributed to the photo-generated charge carriers.

Vacancy Ordering in Ultrathin Copper Oxide Films on Cu(111).

Oxide thin films grown on metal surfaces have wide applications in catalysis and beyond owing to their unique surface structures compared to their bulk counterparts. Despite extensive studies, the atomic structures of copper surface oxides on Cu(111), commonly referred to as "44" and "29", have remained elusive. In this work, we demonstrated an approach for the structural determination of oxide surfaces using element-specific scanning tunneling microscopy (STM) imaging enhanced by functionalized tips. This approach enabled us to resolve the atomic structures of "44" and "29" surface oxides, which were further corroborated by noncontact atomic force microscopy (nc-AFM) measurements and Monte Carlo (MC) simulations. The stoichiometry of the "44" and "29" frameworks was identified as Cu23O16 and Cu16O11, respectively. Contrary to the conventional hypothesis, we observed ordered Cu vacancies within the "44" structure manifesting as peanut-shaped cavities in the hexagonal lattice. Similarly, a combination of Cu and O vacancies within the "29" structure leads to bean-shaped cavities within the pentagonal lattice. Our study has thus resolved the decades-long controversy on the atomic structures of "44" and "29" surface oxides, advancing our understanding of copper oxidation processes and introducing a robust framework for the analysis of complex oxide surfaces.

Thickness measurement of thin films using atomic force microscopy based scratching

Thin-film thickness measurements using atomic force microscopy (AFM) comprise two steps: 1. AFM scratching in order to produce an exposed film edge, and 2. subsequent AFM measurement of the corresponding step height across the exposed edge. Although the technique is known, many open questions have limited its wider applications. In order to clarify the open questions, here we first demonstrate how to determine the normal force applied during the scratching in contact mode needed to completely remove films from substrates. In order to determine film thickness from processed AFM images, we discuss two procedures based on the histogram method and polynomial step-function fitting. Mechanisms of the scratching process are elucidated by the analysis of lateral forces and their enhancement during the film peeling. Phase maps of scratched domains recorded in amplitude modulation AFM (tapping) mode display a clear contrast compared to pristine films. Therefore, we suggest their utilization as simple indicators of spatial domains with completely removed films. As an example, here the measurements were done on polymer films fabricated by layer-by-layer deposition of oppositely charged polyelectrolytes composed of poly(allylamine hydrochloride) and poly(sodium 4-styrenesulfonate), while the applicability of the presented method on other materials is discussed in detail.

Electromigration and electrical sintering in printed silver from high current at room temperature

Improved understanding of the reliability and failure physics of metal nanoparticle conductive inks would facilitate their large-scale deployment across a range of flexible electronics applications. We conduct room-temperature electromigration experiments on printed silver nanoparticle conductive ink test devices. We observe significant variation in failure time, location, and structure during these tests and during post-failure analysis with optical and electron microscopy. We use in situ Atomic Force Microscopy measurements to track volume changes in the sample as a function of time. These measurements provide additional data and understanding of the failure process within printed silver nanoparticle conductive inks.

Toward Humidity-Independent Sensitive and Fast Response Temperature Sensors Based on Reduced Graphene Oxide/Poly(vinyl alcohol) Nanocomposites.

Flexible temperature sensors are becoming increasingly important these days. In this work, we explore graphene oxide (GO)/poly(vinyl alcohol) (PVA) nanocomposites for potential application in temperature sensors. The influence of the mixing ratio of both materials, the reduction temperature, and passivation on the sensing performance has been investigated. Various spectroscopic techniques revealed the composite structure and atomic composition. These were complemented by semiempirical quantum chemical calculations to investigate rGO and PVA interaction. Scanning electron and atomic force microscopy measurements were carried out to evaluate dispersion and coated film quality. The temperature sensitivity has been evaluated for several composite materials with different compositions in the range from 10 to 80 °C. The results show that a linear temperature behavior can be realized based on rGO/PVA composites with temperature coefficients of resistance (TCR) larger than 1.8% K-1 and a fast response time of 0.3 s with minimal hysteresis. Furthermore, humidity influence has been investigated in the range from 10% to 80%, and a minor effect is shown. Therefore, we can conclude that rGO/PVA composites have a high potential for excellent passivation-free, humidity-independent, sensitive, and fast response temperature sensors for various applications. The GO reduction is tunable, and PVA improves the rGO/PVA sensor performance by increasing the tunneling effect and band gap energy, consequently improving temperature sensitivity. Additionally, PVA exhibits minimal water absorption, reducing the humidity sensitivity. rGO/PVA maintains its temperature sensitivity during and after several mechanical deformations.

Hyaluronic Acid/Ellagic Acid as Materials for Potential Medical Application.

The aim of this work was to develop and characterize a thin films composed of hyaluronic acid/ellagic acid for potential medical application. Its principal novelty, distinct from the prior literature in terms of hyaluronic acid films supplemented with phenolic acids, resides in the predominant incorporation of ellagic acid-a distinguished compound-as the primary constituent of the films. Herein, ellagic acid was dissolved in two different solvents, i.e., acetic acid (AcOH) or sodium hydroxide (NaOH), and the surface properties of the resultant films were assessed using atomic force microscopy and contact angle measurements. Additionally, various physicochemical parameters were evaluated including moisture content, antioxidant activity, and release of ellagic acid in phosphate buffered saline. Furthermore, the evaluation of films' biocompatibility was conducted using human epidermal keratinocytes, dermal fibroblasts, and human amelanotic melanoma cells (A375 and G361), and the antimicrobial activity was elucidated accordingly against Staphylococcus aureus ATCC 6538 and Pseudomonas aeruginosa ATCC 15442. Our results showed that the films exhibited prominent antibacterial properties particularly against Staphylococcus aureus, with the 80HA/20EA/AcOH film indicating the strong biocidal activity against this strain leading to a significant reduction in viable cells. Comparatively, the 50HA/50EA/AcOH film also displayed biocidal activity against Staphylococcus aureus. This experimental approach could be a promising technique for future applications in regenerative dermatology or novel strategies in terms of bioengineering.

Strong Covalent Coupling in Vertically Layered SnSe2/PTAA Heterojunctions Enabled High Performance Inorganic-Organic Hybrid Photodetectors.

Controllable large-scale integration of two-dimensional (2D) materials with organic semiconductors and the realization of strong coupling between them still remain challenging. Herein, we demonstrate a wafer-scale, vertically layered SnSe2/PTAA heterojunction array with high light-trapping ability via a low-temperature molecular beam epitaxy method and a facile spin-coating process. Conductive probe atomic force microscopy (CP-AFM) measurements reveal strong rectification and photoresponse behavior in the individual SnSe2 nanosheet/PTAA heterojunction. Theoretical analysis demonstrates that vertically layered SnSe2/PTAA heterojunctions exhibit stronger C-Se covalent coupling than that of the conventional tiled type, which could facilitate more efficient charge transfer. Benefiting from these advantages, the SnSe2/PTAA heterojunction photodetectors with an optimized PTAA concentration show high performance, including a responsivity of 41.02 A/W, an external quantum efficiency of 1.31 × 104%, and high uniformity. The proposed approach for constructing large-scale 2D inorganic-organic heterostructures represents an effective route to fabricate high-performance broadband photodetectors for integrated optoelectronic systems.

Investigations on tip-based large area nanofabrication and nanometrology using a planar nanopositioning machine (NFM-100)

This paper explores large area application of tip-based nanofabrication by field emission scanning probe lithography and showcases the simultaneous possibility of atomic force microscopy on macroscopic scales. This is made possible by the combination of tip-based technology and a planar nanopositioning and nanomeasuring machine. Using long range atomic force microscopy measurement of regular grating structures, the performance of the machine is thoroughly characterized over the full 100 mm range of motion of the positioning machine, which was confirmed by repeated measurements. After initially focussing on achieving the minimum line width of < 40 nm in microscopic areas, a grating with a pitch of 1 μm is additionally fabricated over a total length of 10 mm, whereby the dimensions and deviations are also considered.

Toward coupling across inorganic/organic hybrid interfaces: polyaniline-coated gold nanoparticles with 4-aminothiophenol as gold-anchoring moieties

AbstractThe chemical binding between metal nanoparticles and (semi-)conductive polymer layers is essential to control the (opto-)electronic properties of such hybrid materials. Current approaches that achieve a conjugated binding of organic (semi-)conductive ligands to metal nanoparticles demonstrated promising functional properties, but are based on tedious multi-step organic synthesis to incorporate the required binding moieties at the chain ends of targeted macromolecular species. Herein, we explore the pre-functionalization of gold nanoparticles with p-aminothiophenol and subsequent surfactant-assisted formation of a poly(aniline) (PANI) shell as a means to access gold/PANI core–shell-type nanoparticles with enhanced conductive properties. Controlled surface deposition of these hybrid nanoparticles is achieved via template-assisted self-assembly. For these surface-deposited nanoparticles, charge transport properties are characterized at the nanoscale by conductive atomic force microscopy measurements and show a significant conductivity increase of our core–shell particles as compared to reference particles formed by conventional surfactant-assisted PANI-shell formation. Graphical Abstract