Pressure Ion Source Research Articles

An atmospheric pressure ionization source based on desorption electrospray ionization technology (DESI) for ion cyclotron resonance mass spectrometry

An atmospheric pressure ionization source based on desorption electrospray ionization technology for a bench-top hybrid FTICR mass spectrometer is described. The ion source was characterized using low-molecular-weight-weight pharmaceutical samples. The dependences of signal intensities on various experimental parameters (solvent composition, surface temperature, spray voltage, etc.) were studied. Based on the results obtained, plausible mechanisms of desorption electrospray ionization for the analytes under the study are discussed.

Understanding the Flowing Atmospheric-Pressure Afterglow (FAPA) Ambient Ionization Source through Optical Means

The advent of ambient desorption/ionization mass spectrometry (ADI-MS) has led to the development of a large number of atmospheric-pressure ionization sources. The largest group of such sources is based on electrical discharges; yet, the desorption and ionization processes that they employ remain largely uncharacterized. Here, the atmospheric-pressure glow discharge (APGD) and afterglow of a helium flowing atmospheric-pressure afterglow (FAPA) ionization source were examined by optical emission spectroscopy. Spatial emission profiles of species created in the APGD and afterglow were recorded under a variety of operating conditions, including discharge current, electrode polarity, and plasma-gas flow rate. From these studies, it was found that an appreciable amount of atmospheric H(2)O vapor, N(2), and O(2) diffuses through the hole in the plate electrode into the discharge to become a major source of reagent ions in ADI-MS analyses. Spatially resolved plasma parameters, such as OH rotational temperature (T(rot)) and electron number density (n(e)), were also measured in the APGD. Maximum values for T(rot) and n(e) were found to be ~1100 K and ~4×10(19) m(-3), respectively, and were both located at the pin cathode. In the afterglow, rotational temperatures from OH and N(2)(+) yielded drastically different values, with OH temperatures matching those obtained from infrared thermography measurements. The higher N(2)(+) temperature is believed to be caused by charge-transfer ionization of N(2) by He(2)(+). These findings are discussed in the context of previously reported ADI-MS analyses with the FAPA source.

Numerical Simulation and Experimental Validation of the Three-Dimensional Flow Field and Relative Analyte Concentration Distribution in an Atmospheric Pressure Ion Source

In this study, the validation and analysis of steady state numerical simulations of the gas flows within a multi-purpose ion source (MPIS) are presented. The experimental results were obtained with particle image velocimetry (PIV) measurements in a non-scaled MPIS. Two-dimensional time-averaged velocity and turbulent kinetic energy distributions are presented for two dry gas volume flow rates. The numerical results of the validation simulations are in very good agreement with the experimental data. All significant flow features have been correctly predicted within the accuracy of the experiments. For technical reasons, the experiments were conducted at room temperature. Thus, numerical simulations of ionization conditions at two operating points of the MPIS are also presented. It is clearly shown that the dry gas volume flow rate has the most significant impact on the overall flow pattern within the APLI source; far less critical is the (larger) nebulization gas flow. In addition to the approximate solution of Reynolds-Averaged Navier-Stokes equations, a transport equation for the relative analyte concentration has been solved. The results yield information on the three-dimensional analyte distribution within the source. It becomes evident that for ion transport into the MS ion transfer capillary, electromagnetic forces are at least as important as fluid dynamic forces. However, only the fluid dynamics determines the three-dimensional distribution of analyte gas. Thus, local flow phenomena in close proximity to the spray shield are strongly impacting on the ionization efficiency.

Atmospheric pressure ion focusing with a vortex stream

For successful operation of ionization analysis techniques an efficient sampling and sample ion transportation into an analytical path are required. This is of particular importance for atmospheric pressure ionization sources like corona discharge, electrospray, MALDI, ionization with radioactive isotopes (3H, 63Ni) that produce nonuniform spatial distribution of sample ions. The available methods of sample ion focusing with electric fields are either efficient at reduced pressure (to 1Torr) or feature high sample losses. In this paper we suggest to use a highly whirled gas stream for atmospheric pressure ion focusing. We use a 63Ni radioactive source to produce an ionized bipolar sample at atmospheric pressure. It is shown by experiments that compared to an aspiration method a forced highly whirled vortex stream allows one to enhance the efficiency of remote ionized sample collection at distances equal to the vortex sampler diameter by an order of magnitude. With a vortex stream, a sixfold increase in the efficiency of the radial ionized sample collection has been obtained. It may be deduced that with the vortex stream remote sampling obtains a new feature which is characterized by a considerable enhancement of the efficiency of the ionized sample collection and can be called as a “gas-dynamic” ionized sample focusing. Considered is the effect of recombination losses of the ionized sample during the remote sampling thereof with the vortex sampler. Prospects for a practical implementation of the vortex sampler for solving the problems of the customs control over the smuggling of radioactive α and β sources are made based on the research results.

Single Photon Ionization and Chemical Ionization Combined Ion Source Based on a Vacuum Ultraviolet Lamp for Orthogonal Acceleration Time-of-Flight Mass Spectrometry

A novel combined ion source based on a vacuum ultraviolet (VUV) lamp with both single photon ionization (SPI) and chemical ionization (CI) capabilities has been developed for an orthogonal acceleration time-of-flight mass spectrometer (oaTOFMS). The SPI was accomplished using a commercial 10.6 eV krypton discharge lamp with a photon flux of about 10(11) photons s(-1), while the CI was achieved through ion-molecule reactions with O(2)(+) reactant ions generated by photoelectron ionization at medium vacuum pressure (MVP). To achieve high ionization efficiency, the ion source pressure was elevated to 0.3 mbar and the photoionization length was extended to 36 mm. As a result, limits of detection (LODs) down to 3, 4, and 6 ppbv were obtained for benzene, toluene, and p-xylene in MVP-SPI mode, and values of 8 and 10 ppbv were obtained for toluene and chloroform, respectively, in SPI-CI mode. As it is feasible to switch between MVP-SPI mode and SPI-CI mode rapidly, this system is capable of monitoring complex organic mixtures with a wide range of ionization energies (IEs). The analytical capacity of this system was demonstrated by measuring dehydrogenation products of long-chain paraffins to olefins through direct capillary sampling and drinking water disinfection byproducts from chlorine through a membrane interface.

ケミカルズ覚え書き（機器編）リアルタイム直接質量分析イオン源ＤＡＲＴ（Ｄｉｒｅｃｔ Ａｎａｌｙｓｉｓ ｉｎ Ｒｅａｌ Ｔｉｍｅ）質量分析法の応用

We introduce applications of Direct Analysis in Real Time (DART) ion source, used in open-air at ground potential under ambient conditions, coupled with time-of-flight or quadrupole mass spectrometer.DART was developed in 2005 as a new type of atmospheric pressure ion source. One of the most interesting features of DART is that researchers can access the place of ionizing point directly. It means we can observe real-time spectra of a sample at ground potential under ambient condition. In this paper, we will introduce the principles and features of DART ion source and some applications of DART mass spectrometry.

Using a dual inlet atmospheric pressure ionization source as a dynamic reaction vessel

Atmospheric pressure ionization (API) sources have the ability to serve as dynamic 'reaction vessels' and this capability has been rapidly evolving over the past few years. With API sources, many different reagents and source conditions can be rapidly explored with minimal carryover or contamination of the mass spectrometer. While most API applications involve the simple protonation/deprotonation of analyte molecules, a great deal of flexibility and utility is available in almost any API source, provided the reagents and ionization conditions are judiciously selected. Here, the generation of a unique and useful class of reagent ions at atmospheric pressure is demonstrated for the first time. Within the AP gas-phase environment of a dual inlet ion source, the gas-phase synthesis of substituted N-phenylpyridinium cations is demonstrated by establishing conditions favorable to the nucleophilic substitution reaction required for their formation. The flexibility of this API source as a reaction vessel is also demonstrated.

Ion characterisation by comparison of ion mobility spectrometry and mass spectrometry data

The major uncertainty related to ion mobility spectrometry is the lack of knowledge about the characteristics of the ions detected. When using a radioactive atmospheric pressure ionisation source (e.g. 63Ni), from theory proton bound water clusters are expected as reactant ions. When analyte ions occur, proton transfer should lead to proton-bound monomer and dimer ions. To increase the knowledge about those ionisation processes in an ion mobility spectrometer (IMS), a s-radiation ionisation source was coupled to a mass spectrometer (MS) and an identical one to an IMS. Exemplarily, acetone, limonene and 2- and 5-nonanone were introduced into both instruments in varying concentrations. By correlating the MS and IMS spectra, conclusions about the identities of the ions detected by IMS could be drawn. Proton-bound monomer, dimer and even trimer ions (MH+, 2MH+, 3MH+) could be observed in the MS spectra for acetone and 5-nonanone and could be assigned to the related signals detected by IMS. The oligomers could be expected from theory for increasing concentration. Limonene and 2-nonanone yielded in a variety of different ions and fragments indicating complex gas phase ion chemistry. Those findings on the obviously different behaviour of different analytes require further research focussed on the ion chemistry in IMS including the comparison of different ionisation sources.

Feasibility of gas chromatography–microchip atmospheric pressure photoionization-mass spectrometry in analysis of anabolic steroids

Mass spectrometers equipped with atmospheric pressure ion sources (API-MS) have been designed to be interfaced with liquid chromatographs (LC) and have rarely been connected to gas chromatographs (GC). Recently, we introduced a heated nebulizer microchip and showed its potential to interface liquid microseparation techniques and GC with API-MS. This study demonstrates the feasibility of GC–microchip atmospheric pressure photoionization-tandem mass spectrometry (GC–μAPPI-MS/MS) in the analysis of underivatized anabolic steroids in urine. The APPI microchip provides high ionization efficiency and produces abundant protonated molecules or molecular ions with minimal fragmentation. The feasibility of GC–μAPPI-MS/MS in the analysis of six selected anabolic steroids in urine samples was studied with respect to intra-batch repeatability, linearity, linear range, and limit of detection (LOD). The method showed good sensitivity (LODs 0.2–1 ng/mL), repeatability (relative standard deviation < 10%), and linearity (regression coefficient ≥ 0.9995) and, therefore, high potential for the analysis of anabolic steroids. Quantitative performance of the method was tested with two authentic urine samples, and the results were in good agreement with those obtained with conventional GC–electron ionization-MS after derivatization.

Innovative methodology to transfer conventional GC-MS heroin profiling to UHPLC-MS/MS

Nowadays, in forensic laboratories, heroin profiling is frequently carried out by gas chromatography coupled with mass spectrometry (GC-MS). This analytical technique is well established, provides good sensitivity and reproducibility, and allows the use of large databases. Despite those benefits, recently introduced analytical techniques, such as ultra-high-pressure liquid chromatography (UHPLC), could offer better chromatographic performance, which needs to be considered to increase the analysis throughput for heroin profiling. With the latter, chromatographic conditions were optimized through commercial modeling software and two atmospheric pressure ionization sources were evaluated. Data obtained from UHPLC-MS/MS were thus transferred, thanks to mathematical models to mimic GC-MS data. A calibration and a validation set of representative heroin samples were selected among the database to establish a transfer methodology and assess the models' abilities to transfer using principal component analysis and hierarchical classification analysis. These abilities were evaluated by computing the frequency of successful classification of UHPLC-MS/MS data among GC-MS database. Seven mathematical models were tested to adjust UHPLC-MS/MS data to GC-MS data. A simplified mathematical model was finally selected and offered a frequency of successful transfer equal to 95%.

Atmospheric-pressure Molecular Imaging of Biological Tissues and Biofilms by LAESI Mass Spectrometry

Ambient ionization methods in mass spectrometry allow analytical investigations to be performed directly on a tissue or biofilm under native-like experimental conditions. Laser ablation electrospray ionization (LAESI) is one such development and is particularly well-suited for the investigation of water-containing specimens. LAESI utilizes a mid-infrared laser beam (2.94 μm wavelength) to excite the water molecules of the sample. When the ablation fluence threshold is exceeded, the sample material is expelled in the form of particulate matter and these projectiles travel to tens of millimeters above the sample surface. In LAESI, this ablation plume is intercepted by highly charged droplets to capture a fraction of the ejected sample material and convert its chemical constituents into gas-phase ions. A mass spectrometer equipped with an atmospheric-pressure ion source interface is employed to analyze and record the composition of the released ions originating from the probed area (pixel) of the sample. A systematic interrogation over an array of pixels opens a way for molecular imaging in the microprobe analysis mode. A unique aspect of LAESI mass spectrometric imaging is depth profiling that, in combination with lateral imaging, enables three-dimensional (3D) molecular imaging. With current lateral and depth resolutions of ~100 μm and ~40 μm, respectively, LAESI mass spectrometric imaging helps to explore the molecular structure of biological tissues. Herein, we review the major elements of a LAESI system and provide guidelines for a successful imaging experiment.

Atmospheric-pressure Molecular Imaging of Biological Tissues and Biofilms by LAESI Mass Spectrometry

Ambient ionization methods in mass spectrometry allow analytical investigations to be performed directly on a tissue or biofilm under native-like experimental conditions. Laser ablation electrospray ionization (LAESI) is one such development and is particularly well-suited for the investigation of water-containing specimens. LAESI utilizes a mid-infrared laser beam (2.94 μm wavelength) to excite the water molecules of the sample. When the ablation fluence threshold is exceeded, the sample material is expelled in the form of particulate matter and these projectiles travel to tens of millimeters above the sample surface. In LAESI, this ablation plume is intercepted by highly charged droplets to capture a fraction of the ejected sample material and convert its chemical constituents into gas-phase ions. A mass spectrometer equipped with an atmospheric-pressure ion source interface is employed to analyze and record the composition of the released ions originating from the probed area (pixel) of the sample. A systematic interrogation over an array of pixels opens a way for molecular imaging in the microprobe analysis mode. A unique aspect of LAESI mass spectrometric imaging is depth profiling that, in combination with lateral imaging, enables three-dimensional (3D) molecular imaging. With current lateral and depth resolutions of ~100 μm and ~40 μm, respectively, LAESI mass spectrometric imaging helps to explore the molecular structure of biological tissues. Herein, we review the major elements of a LAESI system and provide guidelines for a successful imaging experiment.

Study of Discontinuous Atmospheric Pressure Interfaces for Mass Spectrometry Instrumentation Development

The discontinuous atmospheric pressure interface (DAPI) has allowed the transfer of ions from atmospheric pressure ionization sources to an ion trap mass analyzer in hand-held mass spectrometers with miniature pumping systems at transfer efficiencies high enough for proper chemical analysis. The DAPI potentially would allow a significant enhancement to the mass analysis efficiency of laboratory-scale mass spectrometers, which have pumping systems of much larger capacities. A laboratory-scale mass spectrometer with a DAPI-RIT (rectilinear ion trap)-DAPI configuration has been developed to explore this possibility. The gas dynamic effects on ion trapping and mass analysis have been studied at various conditions. A pulsed nanoelectrospray ionization source synchronized with the DAPI has been implemented to improve the sample usage efficiency as well as to adjust the number of ions to be trapped for MS analysis, so that space charge effects can be avoided. Single-scan spectra of peptides were recorded with an ionization time as short as 1 mus, corresponding to an analyte consumption of several attomoles. The simplicity of application of the DAPI for performing ion/molecule and ion/ion reactions has also been demonstrated with proton transfer and electron transfer dissociation reactions with peptides.

HANDLING DRAWBACKS OF MASS SPECTROMETRIC DETECTION COUPLED TO LIQUID CHROMATOGRAPHY IN BIOANALYSIS

Hyphenation of mass spectrometry (MS) to liquid chromatography (LC) represents a powerful tool for qualitative and quantitative characterization of target compounds in very complex matrixes of biological origins. In spite of many advantages due to recent advances and innovations in the area of instrumentation and dedicated software support, some difficulties are still encountered in its current applications. The large variety of functional principles and technical solutions applied for hyphenation of the two techniques, for ion sources, ion extraction and focusing, mass analysis, and ion counting makes it more difficult to obtain perfect agreement between the intrinsic characteristics of the laboratory-available instrumentation and the declared goals of specific determination. This review covers a part of the literature data dealing with the shortcomings of LC/MS in bioanalysis. The following topics are discussed: structural identification and confirmation in LC/MS; precision of the instrumental response over short and long term periods; non-linear response functions; adduct formation in atmospheric pressure ion sources; and carryover effects. Most of the problems arising in LC/MS are related to phenomena occurring during ionization. Obviously, the structural characteristics of the analyzed compounds play an important role, although the principles of ionization within the source and the supporting technical solutions and constructive designs add their own particular features. The complex influence of residual sample matrixes over ionization yields of target compounds and internal standards needs to be studied through proper experimental procedures, in order to control both precision and instrumental response function in analysis of biological samples.

IMS–MS studies based on coupling a differential mobility analyzer (DMA) to commercial API–MS systems

Recent progress in adding a mobility dimension to preexisting API–MS systems without modifying the MS itself is discussed, based on inserting a differential mobility analyzer (DMA) as part of the MS's atmospheric pressure ion source. Design criteria leading to high DMA resolving power R and transmission efficiency η are discussed. Various DMA prototypes have been interfaced to several triple quadrupoles, a single quadrupole and a quadrupole-TOF, all demonstrating R > 50 and η > 50%. We obtain two-dimensional DMA–MS spectra of the multiply charged clusters formed in electrosprays of concentrated solutions of tetrahexylammonium bromide (A +Br −). These reveal systematic loss of (ABr)A + fragments from unstable multiply charged clusters, and provide mobility measurements in air on mass resolved ( ABr ) n ( A + ) z clusters with n > 100 and z up to 10. Well-defined bands of ions not individually resolved are clearly visible at considerably larger n and z values.

An experimental and computational study on the dissociation behavior of hydroxypyridine N‐oxides in atmospheric pressure ionization mass spectrometry

A tandem mass spectrometric study of protonated isomeric hydroxypyridine N-oxides was carried out with a hybrid quadrupole/time-of-flight mass spectrometer coupled with different atmospheric pressure ionization sources. The behavior observed in the collision-induced dissociation (CID) mass spectra of the parent cations, was similar irrespective of the source employed. However, there were intrinsic differences in the intensities of the two fragments observed for each isomer. The major fragment because of elimination of a hydroxyl radical, dominated the CID spectra (in contrast with weaker water loss) at different energy thresholds. Therefore, it was possible to differentiate both isomers at collision energies above 13 eV by comparing the ratio of intensities of the major fragment relative to the precursor cation. In addition, quantum chemical calculations at the B3LYP/6-31 + + G(d,p) level of theory were performed for the protonated isomers of hydroxypyridine N-oxide and their radical cation products in order to gain insight into the major routes of dissociation. The results suggest that dissociation from the lowest triplet excited state of the protonated species would provide a reasonable rationalization for the difference in behavior of both isomers.

Detection of radiation-exposure biomarkers by differential mobility prefiltered mass spectrometry (DMS–MS)

Technology to enable rapid screening for radiation exposure has been identified as an important need, and, as a part of a NIH/NIAD effort in this direction, metabolomic biomarkers for radiation exposure have been identified in a recent series of papers. To reduce the time necessary to detect and measure these biomarkers, differential mobility spectrometry–mass spectrometry (DMS–MS) systems have been developed and tested. Differential mobility ion filters preselect specific ions and also suppress chemical noise created in typical atmospheric-pressure ionization sources (ESI, MALDI, and others). Differential-mobility-based ion selection is based on the field dependence of ion mobility, which, in turn, depends on ion characteristics that include conformation, charge distribution, molecular polarizability, and other properties, and on the transport gas composition which can be modified to enhance resolution. DMS–MS is able to resolve small-molecule biomarkers from isobaric interferences, and suppresses chemical noise generated in the ion source and in the mass spectrometer, improving selectivity and quantitative accuracy. Our planar DMS design is rapid, operating in a few milliseconds, and analyzes ions before fragmentation. Depending on MS inlet conditions, DMS-selected ions can be dissociated in the MS inlet expansion, before mass analysis, providing a capability similar to MS/MS with simpler instrumentation. This report presents selected DMS–MS experimental results, including resolution of complex test mixtures of isobaric compounds, separation of charge states, separation of isobaric biomarkers (citrate and isocitrate), and separation of nearly isobaric biomarker anions in direct analysis of a bio-fluid sample from the radiation-treated group of a mouse-model study. These uses of DMS combined with moderate resolution MS instrumentation indicate the feasibility of field-deployable instrumentation for biomarker evaluation.

Direct analysis of melamine in complex matrices using a handheld mass spectrometer

A low temperature plasma ambient ionization source, coupled to a portable mass spectrometer (Mini 10.5), is used for the determination of melamine contamination in whole milk and related materials. Thermally assisted desorption and ionization of the analyte was achieved with the plasma probe. The small size, low power consumption and capability for direct sampling without pretreatment makes plasma ionization an appropriate ionization method for use with a handheld mass spectrometer. The standard discontinuous atmospheric pressure interface used to connect atmospheric pressure ion sources to mass spectrometers (Gao et al., Anal. Chem., 2008, 80, 4026-4032) was modified by using supplementary pumping to increase the ion transfer efficiency. Whole milk, fish, milk powder and other complex matrices spiked with melamine were placed on glass slides close to the vacuum inlet and analyzed without sample pretreatment. Quantitation in complex matrices was achieved using MS/MS of protonated melamine m/z 127 to yield the characteristic fragment ion of m/z 85. Analysis rates of two samples per minute, levels of melamine as low as 250 ng/mL in whole milk (below the regulatory level in the US of 1 ppm (1 microg/mL) or the European level of 2.5 ppm (microg/mL)), a linear dynamic range of 0.5-50 microg/mL and a relative standard deviation of ca. 7.6-16.2% were achieved. The importance of melamine to public health and the prior lack of a rapid, sensitive and yet highly specific field analysis method add to the relevance of this study.

Laser-Induced Acoustic Desorption Coupled with a Linear Quadrupole Ion Trap Mass Spectrometer

In recent years, laser-induced acoustic desorption (LIAD) coupled with a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer has been demonstrated to provide a valuable technique for the analysis of a wide variety of nonvolatile, thermally labile compounds, including analytes that could not previously be analyzed by mass spectrometry. Although FT-ICR instruments are very powerful, they are also large and expensive and, hence, mainly used as research instruments. In contrast, linear quadrupole ion trap (LQIT) mass spectrometers are common due to several qualities that make these instruments attractive for both academic and industrial settings, such as high sensitivity, large dynamic range, and experimental versatility. Further, the relatively small size of the instruments, comparatively low cost, and the lack of a magnetic field provide some distinct advantages over FT-ICR instruments. Hence, we have coupled the LIAD technique with a commercial LQIT, the Thermo Fischer Scientific LTQ mass spectrometer. The LQIT was modified for a LIAD probe by outfitting the removable back plate of the instrument with a 6 in. ConFlat flange (CFF) port, gate valve, and sample lock. Reagent ions were created using the LQIT's atmospheric pressure ionization source and trapped in the mass analyzer for up to 10 s to allow chemical ionization reactions with the neutral molecules desorbed via LIAD. These initial experiments focused on demonstrating the feasibility of performing LIAD in the LQIT. Hence, the results are compared to those obtained using an FT-ICR mass spectrometer. Despite the lower efficiency in the transfer of desorbed neutral molecules into the ion trap, and the smaller maximum number of available laser pulses, the intrinsically higher sensitivity of the LQIT resulted in a higher sensitivity relative to the FT-ICR.

Dielectric Barrier Discharge Ionization for Liquid Chromatography/Mass Spectrometry

An atmospheric pressure microplasma ionization source based on a dielectric barrier discharge with a helium plasma cone outside the electrode region has been developed for liquid chromatography/mass spectrometry (LC/MS). For this purpose, the plasma was realized in a commercial atmospheric pressure ionization source. Dielectric barrier discharge ionization (DBDI) was compared to conventional electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI), and atmospheric pressure photoionization (APPI) in the positive ionization mode. Therefore, a heterogeneous compound library was investigated that covered polar compounds such as amino acids, water-soluble vitamins, and nonpolar compounds like polycyclic aromatic hydrocarbons and functionalized hydrocarbons. It turned out that DBDI can be regarded as a soft ionization technique characterized by only minor fragmentation similar to APCI. Mainly protonated molecules were detected. Additionally, molecular ions were observed for polycyclic aromatic hydrocarbons and derivatives thereof. During DBDI, adduct formation with acetonitrile occurred. For aromatic compounds, addition of one to four oxygen atoms and to a smaller extend one nitrogen and oxygen was observed which delivered insight into the complexity of the ionization processes. In general, compounds covering a wider range of polarities can be ionized by DBDI than by ESI. Furthermore, limits of detection compared to APCI are in most cases equal or even better.