Artificial Aging Research Articles

Onset of Alveolization Processes in Sandstones Exposed to Salt Weathering

Sandstones of the Lourinhã Formation were studied. Alveolization is the major form of weathering on the façades of monuments near Peniche in the western region of Portugal. Salt weathering is an important cause of this degradation form. Stones of specimens, similar to those found in these ancient buildings, were used for an experimental program of artificial salt ageing through the use of sodium chloride, calcium chloride, and sodium sulfate solutions, all at 10% (w/w). Salt weathering follow-up was carried out viz. the assessment of the degradation effect on these specimens of lower values of porosity under crystallization–dissolution cycles. Sodium chloride and sodium chloride with calcium sulfate were the more deleterious solutions, causing failure of the specimens after at least 40 cycles of immersion/drying. Surfaces of the sandstone specimens of variety A showed the onset of the alveolization form due to the use of a saline solution of sodium chloride with calcium sulfate.

Long-term effect of simulated five years professional mechanical biofilm removal on the luting gap of ceramic restorations

BackgroundAchieving sufficient professional mechanical biofilm removal (PMPR) can be challenging in supportive periodontal therapy (SPT), particularly in patients with prosthetic restorations. This experimental study aimed to simulate five years of SPT with periodic PMPR near the luting gap of ceramic restorations using a rubber cup with polishing paste (RCP), air polishing with two different low-abrasive powders (LAPA-1: glycine powder, LAPA-2: erythritol powder), and non-professional mechanical cleaning (control group) to measure the extent of volume loss in the luting gap after baseline (∆V = Vbaseline-V1-5; in µm3).MethodsTwo operators randomly performed PMPR ten times for thirty seconds on one of four sides of 30 crown replicas fixed with glass-ionomer cement (CGIZ: n = 15) or adhesive bonding (CAB: n = 15). The replicas were separated in a template during PMPR, and afterward, cleaned for five seconds per side with a sonic brush under flowing water. The artificial aging process between two PMPRs simulated a 5-year SPT with two PMPRs per year. Profilometric measurements were performed at baseline and after each second PMPR to obtain the mean change of ∆V. The statistical evaluation of the data was carried out using nonparametric tests with Bonferroni correction applied for multiple tests.ResultsNinety-six out of 120 sides could be included in the analysis. PMPR methods showed a loss of substance in the luting gap with a ∆V (mean(standard deviation)) of -4.35 × 106(4.8 × 106)µm3 versus 8.79 × 104(1.05 × 106)µm3 for control at V5 (p ≤ 0.001). No significant differences of ∆V1-5 values could be identified in the control (p > 0.05), whereat all PMPRs showed a significant increasing loss of substance per simulated year (p ≤ 0.001). Intergroup comparison identified LAPA-1 as having the highest significant loss of substance determined on CAB (∆V: -1.05 × 107 (7,2 × 106) µm3), followed by LAPA-2 on CAB (∆V: -6.29 × 106 (4,24 × 106) µm3), LAPA-1 on CGIZ (∆V: -4.15 × 106 (3,25 × 106) µm3), LAPA-2 on CGIZ (∆V: -3.0 × 106 (2,23 × 106) µm3), RCP on CAB (∆V: -1.86 × 106 (2,23 × 106) µm3) and CGIZ (∆V: -1.2 × 106 (1,31 × 106) µm3; p ≤ 0.001)).ConclusionsWithin study limitations, all PMPRs caused a significantly higher loss of substance in the luting gap versus control without professional intervention, with the highest values in the CAB group for LAPA-1, LAPA-2 and RCP. Similar findings were observed for CGIZ, although the loss values were lower.

The strengthening role of post-welded cryogenic treatment on the performance and microstructure of 304 austenitic stainless steel weldments

The metallurgical changes and micro defects after welding can influence the mechanical property, corrosion resistance and dimensional stability of the stainless steel wielding joints. It is necessary to explore an effective post-welded method to improve the service performance for stainless steel welding joints. Furthermore, the essential mechanism between microstructure changes and macro-property variation during this process needs deep reveal. Therefore, this paper aims at investigating the effects of different post-weld treatments including naturally aging, artificial aging and cryogenic treatment on the residual stress and mechanical properties of 304 stainless steel weldments. The microstructure evolution was also studied to reveal and establish the microstructure-performance relationship. The results showed that the distribution of residual stress was most uniform with lowest magnitude (decreased by up to 49%) after cryogenic treatment. At room temperature, weldments subjected to the three post treatments showed similar mechanical properties. At cryogenic temperature, cryogenic treatment exhibited an outstanding role on maintaining the mechanical properties of weldments. By contrast, the mechanical properties were obviously reduced by artificial aging. The transformation of δ-ferrite and the carbide precipitation in grain boundaries are the main reasons for the decrease of mechanical properties after artificially aging. Welding process was able to cause the transfer of the alloying elements and decrease the stability of austenite. Consequently, martensitic transformation can be induced during cryogenic treatment. The new formed martensite resulted in the refined microstructure and high mechanical properties of weldments, and also the release of residual stress after welding.

On the microstructure, texture and electrochemical properties of severely deformed and artificially aged lightweight AA2050 Al–Cu–Li alloy

Lightweight 3rd generation Al–Cu–Li alloy AA2050 was severely deformed via Multi Axial Forging (MAF) at 170 °C followed by artificial aging at 150 °C. Effect of MAF and post MAF aging on microstructure and precipitation was investigated using transmission electron microscopy (TEM). Formation of deformation bands and large dislocation cells were evident on MAF processed samples. Post MAF peak aging resulted in the distribution of fine T1 precipitates in grain interiors with reduction in grain boundary precipitation. Bulk texture studies reveal the formation of strong Goss and S texture components upon MAF processing. Further, low temperature artificial aging doesn’t exhibit significant changes in texture characteristics, either in terms of texture intensities or texture components. Polarization studies showed that peak aged samples exhibited better corrosion resistance compared to un-aged samples. Overall, 12 pass MAF processed and peak aged samples showed higher corrosion resistance. Further, corrosion surface morphologies examination revealed the change in corrosion mechanisms with thermomechanical treatments. Improved corrosion resistance after MAF and peak aging widens the requirements in aerospace and aircraft applications for such engineering alloys.

Microstructural evolution and hardening phenomenon caused by aging of AlSi10Mg alloy by laser powder bed fusion

Microstructures and age-hardening phenomena of directly aged (artificial aged) AlSi10Mg alloys fabricated by laser powder bed fusion (LPBF) were characterized using scanning transmission electron microscopy, atom probe tomography, and Vickers hardness testing. The microstructure derived from overlapping melt pools has a full cellular structure consisting of eutectic Si walls surrounding α-Al cells. In the initial stage of aging, solute clusters with density on the order of 1024/m3 were formed in α-Al cells. By prolonging the aging time further, fine Si particles of about 50 nm in diameter precipitated. Before Si precipitation, the hardness of the aged sample was clearly greater than that of the as-built state. With further aging time, the hardness increased further because of the Si precipitation. Cluster analysis revealed that the number density and the size of clusters increased from as-built state by aging, whereas the types of the solute clusters remained almost unchanged by aging. The results indicate that the nanoscale clusters within the α-Al cells, which increase via aging, produce age-hardening effect.

Kinetic Monte Carlo simulations of solute clustering during quenching and aging of Al–Mg–Zn alloys

The physical mechanisms behind cluster formation during quenching and aging of age-hardening metallic alloys are poorly understood based on classical nucleation and growth theories, especially in multicomponent alloys with supersaturated vacancies and fast-diffusing solute atoms. Here, solute clustering in an Al–Mg–Zn alloy during quenching immediately after high-temperature (800 K) solution treatment is modeled with a newly developed kinetic Monte Carlo (kMC) framework. This includes accurate surrogate models trained using first-principles-calculated data to predict vacancy migration energetics on the fly as functions of local lattice occupations. First, kMC simulations at constant aging temperatures revealed that temporal evolution of the number, sizes, and compositions of solute clusters change with aging temperature. Such changes are consistent with our analyses based on classical nucleation theory (CNT) and Monte Carlo simulations. Second, the kMC algorithm was revised for simulating quenching processes by iteratively updating the kMC temperature based on simulated cooling rate profiles. These quenching simulations show that rapid solute clustering mainly occurs from ∼600 to ∼400 K during cooling. Below ∼400 K, the clustering is suppressed to a steady state because vacancies are trapped by stable clusters with sizes of ∼2 nm and high magnitudes of formation energies. The configurations of these steady-state clusters closely resemble the solute clusters we observed experimentally in 7XXX series Al–Mg–Zn-based alloy samples immediately after quenching. A two-stage vacancy trapping mechanism revealed in our simulations can provide physical guidance to tune precipitation kinetics during natural and artificial aging.

Improving joint performance of friction stir welded 2195-O Al–Li alloy by post-weld heat treatment and rolling deformation

Post-weld heat treatment and rolling deformation are used to improve the mechanical properties of 2195-O Al–Li alloy friction stir welding (FSW) joints, and the effects on the grain structure, precipitation behaviors, hardness distribution, and tensile performance are discussed. Microstructural characterization was conducted using scanning electron microscopy (SEM), electron backscattered diffraction (EBSD), and transmission electron microscopy (TEM). Mechanical properties were measured by hardness test and tensile test. Results show that coarse precipitates are subjected to various degrees of dissolution after FSW. Solution treatment following artificial aging (SAA) and 40% rolling deformation + SAA treatment (R40-SAA) enables the dissolution of coarse precipitates completely and precipitation of strengthening phases (T1 and θ′) in the nugget zone (NZ), thermo-mechanically affected zone and heat-affected zone (HAZ). These strengthening precipitates have little difference in precipitation behavior after SAA and R40-SAA treatment and remain consistent across all regions, resulting in joint hardness change a little between these two joints with a homogeneous distribution. The change in precipitates leads to an increase in hardness and enhances both the SAA joint strength and the R40-SAA joint strength to 503 MPa and 528 MPa (superior to the original joints by 309 MPa and 334 MPa, respectively), respectively. The SAA joints fracture in the NZ resulting from the development of AGG, and develop an intergranular fracture morphology with an elongation of 4.2%. The R40-SAA joints have an elongation of 7.2% due to the generation of uniformly fine grains in the NZ, and fail in the HAZ exhibiting a brittle fracture mechanism.

On the influence of crystallographic texture on cyclic hardening of an AlMgSi alloy

The influence of crystallographic texture on hardening achieved by cyclic loading at room temperature, was tested by comparing samples from an axisymmetric round bar and a flat profile, both made of non-recrystallized, extruded profiles of similar AlMgSi alloys (AA6082). It was found that the plastic strain accumulated during the cyclic loading was significantly (nine times) larger for the flat profile. Tensile testes of the cyclically hardened samples revealed that in spite of the large accumulated plastic strain during cyclic hardening of the flat sample, the local tensile strain at fracture in the necking region was similar to the peak aged conditions obtained by artificial aging.

The Effect of Different Decontamination Methods on the Micro-Tensile Bond Strength of CAD/CAM Resin-Based Blocks to Resin Cement.

This study evaluates the impact of decontamination methods on Microtensile bond strength (μTBS) between resin cement and resin blocks. Twenty CAD/CAM resin blocks from two manufacturers were wet-polished, sandblasted, and ultrasonically cleaned. After blood and saliva contamination, blocks were divided into subgroups: control, water rinsing, acid etching, alkaline cleaning paste, or 10-MDP containing cleaner. Resin-based cement was then applied. After 24 hours, the blocks were sectioned to obtain bars for testing. Half of the specimens were tested immediately for μTBS, and the other half underwent artificial aging. The surfaces of the blocks were inspected with a scanning electron microscope (SEM). Three-way ANOVA was performed for μTBS values (α=0.05). In one of the substrates, the positive control subgroup obtained the highest value (56,01 MPa, SD:6,96) followed by 10-MDP cleaner and universal cleaning paste, when immediately tested, with significant differences respect to the water rinsing (p⟨0.041) and acid etching (p⟨0.048) groups. After thermocycling, higher values were found in the 10-MDP cleaner (47,57 MPa, SD:8,15), but differences were not significant. In the other substrate group, the 10-MDP cleaner subgroup showed highest bond strengths (64,46 MPa SD: 10,92) at the initial test. After thermocycling, 10-MDP cleaner (58,66 MPa, SD: 9,93) gave the highest μTBS value. Significant differences between water rinsing group and the rest of subgroups (p⟨0.001), and between 10-MDP cleaner and the positive control group (p⟨0.006) were observed. Cleaning after contamination improves bonding. 10-MDP containing cleaner can help to restore initial μTBS value and maintain it in the long-term.

Perspectives on Development of Optoelectronic Materials in Artificial Intelligence Age.

Optoelectronic devices, such as light-emitting diodes, have been demonstrated as one of the most demanded forthcoming display and lighting technologies because of their low cost, low power consumption, high brightness, and high contrast. The improvement of device performance relies on advances in precisely designing novelty functional materials, including light-emitting materials, hosts, hole/electron transport materials, and yet which is a time-consuming, laborious and resource-intensive task. Recently, machine learning (ML) has shown great prospects to accelerate material discovery and property enhancement. This review will summarize the workflow of ML in optoelectronic materials discovery, including data collection, feature engineering, model selection, model evaluation and model application. We highlight multiple recent applications of machine-learned potentials in various optoelectronic functional materials, ranging from semiconductor quantum dots (QDs) or perovskite QDs, organic molecules to carbon-based nanomaterials. We furthermore discuss the current challenges to fully realize the potential of ML-assisted materials design for optoelectronics applications. It is anticipated that this review will provide critical insights to inspire new exciting discoveries on ML-guided of high-performance optoelectronic devices with a combined effort from different disciplines.

Evaluation of Hydrothermally Treated Wood Fibre Performance in Cement Mortars

Biofibres’ wide application in mortar enhancement has thus far been restricted by factors related to their chemical composition and hygroscopic nature. Their hydrophilic behaviour increases the water demand of mortar mixtures and diminishes their affinity to the matrix, while further moisture-related fibre degradation issues may arise. Additionally, natural fibres seem to be susceptible to degradation caused by exposure to alkaline environmental conditions such as those experienced by cement mortars, restricting their utilisation in the construction industry. Therefore, the current study investigates the potential of fibre modification through treatments that would permanently alter their structure and chemical composition to improve their performance. In this study, wood fibres of black pine and beech species were exposed to mild thermal treatment (140 °C 2 h, under a steam atmosphere), characterised in terms of the physical and chemical properties and incorporated in cement mortars, applying the proportion of 1.5% v/v in the mortar, in order to assess their performance as reinforcement material. The mortars’ workability (at a fresh state) was examined, as well as other physical, hygroscopic, thermal, and mechanical characteristics of the mortars at the ages of 28, 90 and 365 days and weathering performance, by subjecting them to different artificial ageing environments (freeze–thaw cycles or outdoor exposure). The results revealed the beneficial role of the treated fibres in dimensional stability, flexural strength, thermal insulation properties and capillary absorption of the mortar specimens, especially during the ageing process, with the black pine fibres showing the greatest improvement. The hydrothermally treated wood fibres seem to help maintain the integrity of cement mortars under all ageing conditions, proving that they could provide low-cost and eco-friendly mortar enhancement pathways.

Effect of heat treatments on microstructure and mechanical behavior of laser welded LPBF AlSi10Mg alloys

In this work, heat treatments were performed on autogenously laser welding of laser powder bed fusion (LPBF) AlSi10Mg alloys to improve mechanical properties of welded joints. After welding, the welded joint was heat treated by direct aging (DA) and solution heat treatment and artificial aging (T6) treatment. The porosity, microstructure and mechanical performance of the welded joints after DA and T6 treatments were investigated and compared with the as-welded joint. Results show that the microhardness of weld metal (WM) has been increased to over 93.5 HV0.1 after DA treatment, while the microhardness in the T6 welded joint is reduced to 77.0 HV0.1, from 82.0 HV0.1 in the as-welded joint. The ultimate tensile strength (UTS) of the DA treated joint reaches 276.5 MPa, showing an increase of 43.0% compared with as-welded joint. The DA heat treatment of the LPBF AlSi10Mg welded joints effectively improves the hardness and the UTS, which can be mainly attributable to the reduction of the hydrogen pores, the enhancing effect of solid solution strengthening coming from the Si element in the Al matrix and the dispersion strengthening of Si precipitation.

Accelerated stress test protocol for solid oxide cell based on ex-situ artificial aging of the fuel electrode via redox-cycling - In memory of Prof. A. Milchev

Accelerated stress test protocol for solid oxide cell based on ex-situ artificial aging of the fuel electrode via redox-cycling - In memory of Prof. A. Milchev

Effect of Weight Percent Mg and Heat Treatment on the Mechanical Properties of Al10Si Aluminum Alloy Casting Products Car Chassis Materials

Innovation in the automotive field is now growing rapidly. New materials are considered to be incorporated in automotive design if they have economic and vehicle performance benefits. This research investigates the change of the Magnesium (Mg) addition and heat treatment to the mechanical properties and microstructure of the car chassis prototype with Al10Si Aluminum alloy base material. The process of casting using the High-Pressure Die Casting method. Variation of Mg (3, 4, 5 wt%) to increase the strength of mechanical properties of Al10Si aluminum alloy material. In the casting process, the first Al10Si heated up to 690°C. Mg is incorporated into the heating furnace, then stirred by a mechanical stirrer. Stirring speed of 90 rpm and stirring time of 120 seconds. After it has poured into the mold, the casting temperature is 740°C. Then cools the room to room temperature 39°C. Then performed, heat treatment, using the method of age hardening and artificial aging. The test results prove that the hardening heat treatment makes the grain size smaller. Small grain size, then increase the strength of the material with the addition of Mg elements.

Evaluating the Atypical Aging Potential Development in Sparkling Wines Can Be Achieved by Assessing the Base Wines at the End of the Alcoholic Fermentation.

Traditional sparkling wine production is a lengthy and costly process, involving a double fermentation step and a period of aging sur lie; thus, monitoring quality during the key manufacturing stages is crucial. The effects of the second fermentation on the development of 2-aminoacetophenone (AAP), the main marker of the atypical aging (ATA) defect, were investigated on 55 base wines (BWs) and corresponding sparkling wines (SWs) produced in an experimental winery. While the AAP content of the SWs was observed to be higher than the BWs, it was found that an artificial aging test carried out on the BWs could be a good predictor of ATA development in SWs. Further, the antioxidant capacity of the SWs was noticed to correlate well with the potential AAP formed during accelerated aging. Finally, an analysis of covariance (ANCOVA) model of linearization capable of predicting AAP formation in SWs using the data obtained from the corresponding BWs was created.

Effects of different combinations of artificial ageing and warm forming on Ω phase and S phase evolutions in an Al-5.1Cu-1.0Mg-0.4Ag high strength aluminum alloy

Unlike common age-hardening materials, deformation prior to artificial ageing has been found to adversely affect the hardness of AA2040 aluminum alloy. To prevent this disadvantage, the effects of four different combinations of warm forming and artificial ageing at 200 °C on the microstructures and Vickers hardness of Al-5.1Cu-1.0Mg-0.4Ag aluminum alloy have been investigated. Among the four different combinations, the combination of 5% warm forming +1 h ageing yielded the lowest hardness value (154 HV), while that of 40 min ageing + 5% warm forming + 20 min ageing yielded the highest (169 HV). It is presumed that the proper timing of inducing dislocations by warm forming is decisive. The appropriate combination of warm forming and artificial ageing, i.e., 40 min + 5%+20 min treatment, produces a suitable amount of Ω phase during the first-stage ageing (40 min ageing), induces dislocations in the subsequent warm forming (5% deformation), and causes the significant amount of lath-like S phase to form on dislocations during the final-stage ageing (20 min ageing), thus enhancing the overall mechanical strength.

Developing Low Cost Eco-friendly Restoration Mortars for Historic Lime-based Stucco and Building Materials

In this work, three formulations based on hydrated lime and eco-friendly additives of powdered brick, fly ash and silica fume were designed to improve repair mortars for historic lime-based stucco and building materials. The microscopic features, physical-mechanical behavior and the microstructure of the prepared mortars were evaluated before and after artificial ageing (by humidity/drying cycles and salt weathering). However, a significant mechanical enhancement was reported for the studied mixes, but the silica fume mix showed a notable failure after salt ageing. The fly ash mix revealed the highest bulk density ratio (1.172 g/cm3) compared to the lime and silica fume mixes. The silica fume mix recorded the lowest percentage of water absorption (35.56%) and apparent porosity (28.11%). Further, the silica fume mix yielded the highest dry compressive strength value (22.19 kg/cm2), with an increase reached 31% when compared to the standard lime mix. The results demonstrated that the fly ash mortar is more compatible for sustainable restoration procedures of historic lime-based structures in respect of the physical-mechanical properties.

Comparison of the Flexural Strength of Three Different Aged and Nonaged 3D-Printed Permanent Crown Resins.

The aim of this study was to evaluate the flexural strength properties of three different aged and nonaged 3D-printed resins built by different 3D printing systems used in dental applications. Bars (2 × 2 × 25 mm) were additively fabricated using a 3D printer and different dental crown resins (Saremco Crowntec, Senertek P-Crown V2, and Senertek P-Crown V3) per the manufacturers' recommendations. Each subgroup was divided into aged and nonaged subgroups (n = 10 bars per group). Thermocycling procedures (5° to 55°C; 5,000 cycles) were performed under favorable conditions for the aged subgroups from each material. Flexural strength (MPa) was measured in all samples using a universal test machine. When both aged and nonaged resins are compared, significant differences were found in flexural strength measurements (P < .001). The highest flexural strength was observed in the Saremco Crowntec group, while the lowest flexural strength was observed in the Senertek P Crown V2 group. The flexural strength measurements of Saremco Crowntec and Senertek P Crown V3 displayed no significant difference between their aged and nonaged groups (P > .05), while Senertek P Crown V2 (P = .039) showed significant differences between its aged and nonaged groups. Saremco Crowntec showed the highest flexural strength both in aged and nonaged groups, while Senertek P Crown V2 had the lowest strength. The artificial aging process decreased flexural strength values in all 3D-printed resin groups.

Comparative Analysis of Color Stability and Its Impact on Artificial Aging: An In Vitro Study of Bioactive Chitosan, Titanium, Zirconia, and Hydroxyapatite Nanoparticle-Reinforced Glass Ionomer Cement Compared With Conventional Glass Ionomer Cement.

Background Discoloration affects glass ionomer cement (GIC) color stability due to its brittle nature and microporosity. To counter this, incorporating alternative materials is essential for maintainingcolor stability. Aim This study aims to determine the color stability and gloss of GIC modified with bioactive chitosan, titanium, zirconia, and hydroxyapatite nanoparticles before and after artificial aging. Materials and methods The study was conducted at Saveetha Research Centre, Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences, Saveetha University, located in Chennai, India. Green-mediated chitosan, titanium, zirconia, and hydroxyapatite (Ch-Ti-Zr-HA) nanoparticles were synthesized using the one-pot synthesis technique. Forty-eight disc-shaped specimens were prepared by incorporating the obtained nanoparticles (nanocomposite) into the GIC, with a diameterof 5 mm and thicknessof 2 mm. The specimens were prepared in different concentrations (3%, 5%, and 10%) designated as group I, group II, and group III, respectively. Group IV, serving as the control, consisted of conventional GIC without any modifications. Following preparation, scanning electron microscopy (SEM) and energy-dispersive X-ray(EDX)microanalysisconfirmed sample elements, and the specimens were submerged in distilled water for a duration of 24 hours prior to the commencement of testing. Subsequently, the specimens underwent artificial aging (thermocycling),between temperatures of 5°C and 55°C, for a total of 30,000 cycles, with a 30-second dwell time. Color change and gloss characteristics were assessed both after 24 hours and following thermocycling using a spectrophotometer and glossometer, respectively. The average color change parameter (ΔE)was measured using Adobe Photoshop. The data obtained were subjected to statistical analysis using an unpaired t-test. Results Significant color stability variations were observed post thermocycling (P = 0.001). Group 2 (5%) exhibited minimal delta E difference (0.508 ± 0.105), indicating superior color stability, while group 4 (control) had maximum difference (1.15 ± 0.187), indicating lower stability. Gloss tests confirmed GIC's polishability, where there were significant differences among all the groups. Conclusion It can be concluded that 5% nanoparticle-modified GIC has better color stability and gloss than conventional GIC. Further studies are needed to analyze the color stability and gloss through dentifrices and other beverages.

Direct artificial aging of the PBF-LB AlSi10Mg alloy designed to enhance the trade-off between strength and residual stress relief

The AlSi10Mg alloy is one of the most studied alloys processed by the Powder Bed Fusion-Laser Beam (PBF-LB). Many already published works focus on post-process heat treatments to reduce residual stress or improve mechanical strength. Instead, the present study aims to identify direct artificial aging (AA) heat treatment able to optimize both aspects, thus enhancing the trade-off between strengthening and residual stress relief for the PBF-LB AlSi10Mg alloy produced using a no-heated platform. Higher temperatures (190–240 °C) than those typically used in AA heat treatment were selected based on thermal analysis to benefit both residual stress relief and precipitation of reinforcing phases from the supersaturated solid solution of the metastable as-built alloy. The effects of AA heat treatment on mechanical properties (i.e. hardness) and residual stress were evaluated by plotting aging curves and by XRD and Raman analyses and demonstrated that different trade-offs between strengthening and stress relief can be achieved by tuning heat treatment parameters (temperature and time). In particular, the exposure at the lowest temperature (190 °C) induced a partial decrease in residual stress and a slight increase in hardness. By increasing heat treatment temperature and soaking time, the relief was more significant, whilst the decrease in hardness was rather limited. The results are supported by the microstructural changes observed on the samples due to the different heat treatment conditions applied and show the feasibility of designing an AA heat treatment for the PBF-LB AlSi10Mg alloy capable of satisfying the mechanical response required by the final application.