Silicon Photomultiplier Array Research Articles

Novel 4x4 SiPM array readout with integrated preamplification stage, optimized for the PWO detectors of the EIC EEEMCal

We are reporting on a new readout circuit developed for the lead tungstate (PbWO4) scintillation detectors for the Electron Ion Collider (EIC) Electron Endcap Electromagnetic Calorimeter EEEMCal. The high magnetic field region precludes the use of photomultiplier tubes while the detector requirements specify good spectral resolution performance and fast pulse integration over a large dynamic range. We selected a silicon photomultiplier (SiPM) from Hamamatsu and produced a matrix of 4 x 4 sensors to cover the 20 mm × 20 mm scintillator coupling surface. Signal acquisition and amplification electronics boards were designed and integrated with the sensor board to produce a compact high performance readout package. A prototype detector was built and tested at Jefferson Lab with encouraging resolution and timing performance results.

DOI- and TOF-capable PET array detector using double-ended light readout and stripline-based row and column electronic readout.

We investigate a highly multiplexing readout for depth-of-interaction (DOI) and time-of-flight PET detector consisting of an N×N crystals whose light outputs at the front and back ends are detected by using silicon photomultipliers (SiPM). The front N×N SiPM array is read by using a stripline (SL) configured to support discrimination of the row position of the signal-producing crystal. The back N×N SiPM array is similarly read by an SL for column discrimination. Hence, the detector has only four outputs. We built 4×4 and 8×8 detector modules (DM) by using 3.0×3.0×20 mm3 lutetium-yttrium oxyorthosilicates. The outputs were sampled and processed offline. For both DMs, crystal discrimination was successful. For the 4×4 DM, we obtained an average energy resolution (ER) of 14.1%, an average DOI resolution of 2.5 mm, a non DOI-corrected coincidence resolving time (CRT), measured in coincidence with a single-pixel reference detector, of about 495 ps. For the 8×8 DM, the average ER, average DOI resolution and average CRT were 16.4%, 2.9 mm, and 641 ps, respectively. We identified the intercrystal scattering as a probable cause for the CRT deterioration when the DM was increased from 4×4 to 8×8.

Design of the ASIC readout scheme for the JUNO-TAO experiment

The Taishan Antineutrino Observatory (TAO) has been proposed to precisely measure the reactor antineutrino spectrum with an energy resolution better than 2% at 1 MeV. It can provide a reference spectrum to the Jiangmen Underground Neutrino Observatory (JUNO) to enhance its sensitivity to the neutrino mass ordering measurement. In addition, TAO can also provide a benchmark to verify the nuclear database and conduct new physics searches. The TAO detector is a 2.8-ton liquid scintillator detector equipped with a 10 m2 silicon photomultiplier (SiPM) array to collect the light with a coverage of 94%. The TAO detector will be operated at -50 °C to suppress the SiPM dark count rate. In this work, we report on the design of a readout system based on the KLauS6 chip to handle the outputs from the SiPMs, which exhibits advantages of high granularity (potentially good particle identification) and large dynamic range. A dedicated mockup system has been built and its performance carefully evaluated both at room and low temperatures, measuring gain, charge linearity, signal-to-noise ratio, and dead time. The testing results show that the performance of this system can meet the requirements of TAO. However, an abnormal increase in current at 1.8 V analog power of the KLauS6 chip has been observed when operating it at temperatures below -20 °C, resulting in a potential risk on the long-term reliability. Therefore, the KLauS-based readout design is considered as an alternative option for the future upgrading of the TAO's readout system. This study also provides a reference and guidance for other relevant applications.

Scintillation and cherenkov photon counting detectors with analog silicon photomultipliers for TOF-PET

Objective. Standard signal processing approaches for scintillation detectors in positron emission tomography (PET) derive accurate estimates for 511 keV photon time of interaction and energy imparted to the detection media from aggregate characteristics of electronic pulse shapes. The ultimate realization of a scintillation detector for PET is one that provides a unique timestamp and position for each detected scintillation photon. Detectors with these capabilities enable advanced concepts for three-dimensional (3D) position and time of interaction estimation with methods that exploit the spatiotemporal arrival time kinetics of individual scintillation photons. Approach. In this work, we show that taking into consideration the temporal photon emission density of a scintillator, the channel density of an analog silicon photomultiplier (SiPM) array, and employing fast electronic readout with digital signal processing, a detector that counts and timestamps scintillation photons can be realized. To demonstrate this approach, a prototype detector was constructed, comprising multichannel electronic readout for a bismuth germanate (BGO) scintillator coupled to an SiPM array. Main Results. In proof-of-concept measurements with this detector, we were able to count and provide unique timestamps for 66% of all optical photons, where the remaining 34% (two-or-more-photon pulses) are also independently counted, but each photon bunch shares a common timestamp. We show this detector concept can implement 3D positioning of 511 keV photon interactions and thereby enable corrections for time of interaction estimators. The detector achieved 17.6% energy resolution at 511 keV and 237 ± 10 ps full-width-at-half-maximum coincidence time resolution (CTR) (fast spectral component) versus a reference detector. We outline the methodology, readout, and approach for achieving this detector capability in first-ever, proof-of-concept measurements for scintillation photon counting detector with analog silicon photomultipliers. Significance. The presented detector concept is a promising design for large area, high sensitivity TOF-PET detector modules that can implement advanced event positioning and time of interaction estimators, which could push state-of-the-art performance.

Characterization of external optical crosstalk reduction for SiPM-based scintillation detectors with an optical bandpass filter

External optical crosstalk remains a significant source of correlated noise in scintillation detectors optically coupled to silicon photomultiplier (SiPM) arrays and can influence achievable performance by limiting the maximum overvoltage at which a detector can be operated. This study evaluated the potential benefits of incorporating an optical bandpass filter, which is absorptive to optical crosstalk and transmissive for scintillation photons, between the scintillator and SiPM array. Several SiPM and bandpass configurations were characterized, including single-element and SiPM arrays with bare, filter-coupled, crystal-coupled, and crystal-filter-coupled interfaces. Coupling the optical filter between a 4 × 4 array of Broadcom AFBR-S4N44P164 M (NUV-MT) SiPMs and a 12 × 12 × 20 mm3 LYSO crystal decreased the total number of detected optical photon noise by up to 92%. The impact of the filter on crosstalk probability reduction was also characterized by the single-channel measurements with the same SiPM, suppressing external crosstalk up to 64%. With the filter coupled, SiPMs were operable at very high overvoltage. The results of these studies demonstrate that optical filtering is a promising technique to significantly reduce correlated noise in scintillation detectors employing SiPMs.

Development of a compact scintillator-based gamma-ray neutron detector for terrestrial and space applications

We present the development of a gamma ray and neutron detector for possible use in terrestrial and planetary science. The detector is based on a monolithic scintillator coupled to an array of silicon photomultipliers (SiPMs) read out by compact integrated electronics, and it shall allow one to detect gamma-rays and neutrons with energies from 0.025 eV to 1 MeV with energy resolution of < 4% full-width half-maximum (FWHM) at 662 keV (Cs-137). Among the various scintillators studied, we measured the energy resolution of 4.87% FWHM at 662 keV with a monolithic and cylindrical CLLBC and confirmed acceptable sensitivity to thermal neutrons at 3.1 MeV. The results are promising towards our goal to measure the abundance of hydrogen bearing compounds and rock-forming elements for planetary geology research.

A continuous depth encoding PET detector using side readout of dual-layer GAGG crystals with SiPM array

A continuous depth encoding positron emission tomography (PET) detector using a side readout configuration with dual-layer GAGG scintillators of different decay times, coupled to a Silicon Photomultiplier (SiPM) array is proposed. The performance of the detector was evaluated through experimentation. The detector consists of an upper layer with a 1 × 4 fast decay GAGG (GAGG-F) crystal array and a lower layer with another 1 × 4 high-light-yield GAGG (GAGG-HL) crystal array. The 2 × 4 GAGG crystal array is then coupled to the 4 × 6 SiPM array. The SiPM array's sum signal is utilized for layer identification, while 24 individual signals are used to measure the 3D position of the gamma interaction. The experimental measurements demonstrate that the detector effectively resolves all crystal units and provides continuous depth information in the Z-direction. Utilizing the time over threshold method for dual-layer identification in coincidence mode yielded an accuracy of 96.4 %, whereas the pulse decay time method achieved an accuracy of 95.7 %. The average energy resolution was found to be 12.1 % and 11.2 % for the upper and lower GAGG crystal arrays, respectively. Using the maximum value-to-sum ratio method, the upper GAGG-F crystal layer displayed clear distinction and accurate assignment at two height positions, achieving a correct assignment rate of 90.5 %. In contrast, the lower GAGG-HL crystal layer exhibited poorer resolution at each height position, with correct assignment percentages dropping to 71.1 %. Employing the center of gravity position estimation method for the GAGG-F and GAGG-HL layers, the average Z spatial resolution was determined as 3.56 ± 0.33 mm (FWHM) and 3.35 ± 0.28 mm (FWHM).

A Portable Three-Layer Compton Camera for Wide-Energy-Range Gamma-ray Imaging: Design, Simulation and Preliminary Testing

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in the active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy. (2) Methods: To realize gamma-ray imaging in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, is developed using the scintillation detector that consists of an silicon photomultiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on the two interaction events is applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of the detectors is established based on the Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources have been successfully obtained with our prototype in laboratory tests and compared with simulation studies. (3) Results: The proportion of effective imaging events accounts for about 2%, which allows our prototype to realize the reconstruction of the distribution of a 0.05 μSv/h 137Cs source in 10 s. The angular resolution for resolving two 137Cs point-like sources is 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrates the imaging capability for high incident energy. (4) Conclusions: We conclude that the prototype has a good imaging performance in a wide energy range (0.3~7 MeV), which shows potential in several MeV gamma-ray imaging applications.

Development of the front-end electronics for a cost-effective PET-like detector system

Most detector systems used for positron emission particle tracking (PEPT) are very expensive due to the use of inorganic plastic scintillators combined with a high number of readout electronic channels. This work aims to reduce the overall cost of a PEPT-capable detector system by using large and cost-effective plastic scintillators and developing custom 2 × 2 silicon photomultiplier (SiPM) arrays, preamplifiers, and discriminators. The use of long (20mm × 20mm × 1000 mm) plastic scintillator bars read out with photodetectors only at their respective ends allows an overall smaller number of photodetectors and associated readout electronics, which in turn reduces the overall cost of the system. In addition, the development of a custom SiPM array and preamplifier allows a free selection of interconnection and readout, as most commercial producers only offer specific types of interconnections and therefore lack other connections such as serial or hybrid. Thus, several common circuit types for SiPMs and preamplifiers were tested and compared in this work, and it was found that a serial connection implemented in a hybrid interconnection for the SiPMs and an inverting preamplifier based on a high-frequency operational amplifier provided the best results for the proposed detector system. Measured with a 22Na source, the combination of SiPM array and preamplifier led to a rise time of 3.7ns and a signal amplitude of 175 mV.

Development of the scintillating fiber timing detector for the Mu3e experiment

We present the development and discuss the performance of a compact scintillating fiber detector for the Mu3e experiment for accurate time measurements at very high particle rates. Mu3e is a new experiment under preparation at the Paul Scherrer Institut (PSI) to search for charged Lepton Flavor Violation in the neutrinoless muon decay μ+→e+e−e+ with a projected sensitivity of 10−16 using the most intense continuous surface muon beam in the world. A very thin scintillating fiber detector (thickness <0.2% of a radiation length X0) with a time resolution of about 250 ps, efficiency around 97%, and spatial resolution of ∼100μm has been developed. The SciFi detector is read out with multi-channel silicon photomultiplier arrays at both ends to achieve the best timing performance. Different scintillating fiber types have been evaluated and various assembly procedures have been tested to achieve the best performance.

Development and performance of SIAT bPET: a high-resolution and high-sensitivity MR-compatible brain PET scanner using dual-ended readout detectors.

Positron emission tomography/magnetic resonance imaging (PET/MRI) is a powerful tool for brain imaging, but the spatial resolution of the PET scanners currently used for brain imaging can be further improved to enhance the quantitative accuracy of brain PET imaging. The purpose of this study is to develop an MR-compatible brain PET scanner that can simultaneously achieve a uniform high spatial resolution and high sensitivity by using dual-ended readout depth encoding detectors. The MR-compatible brain PET scanner, named SIAT bPET, consists of 224 dual-ended readout detectors. Each detector contains a 26 × 26 lutetium yttrium oxyorthosilicate (LYSO) crystal array of 1.4 × 1.4 × 20 mm3 crystal size read out by two 10 × 10 silicon photomultiplier (SiPM) arrays from both ends. The scanner has a detector ring diameter of 376.8mm and an axial field of view (FOV) of 329mm. The performance of the scanner including spatial resolution, sensitivity, count rate, scatter fraction, and image quality was measured. Imaging studies of phantoms and the brain of a volunteer were performed. The mutual interferences of the PET insert and the uMR790 3T MRI scanner were measured, and simultaneous PET/MRI imaging of the brain of a volunteer was performed. A spatial resolution of better than 1.5mm with an average of 1.2mm within the whole FOV was obtained. A sensitivity of 11.0% was achieved at the center FOV for an energy window of 350-750keV. Except for the dedicated RF coil, which caused a ~ 30% reduction of the sensitivity of the PET scanner, the MRI sequences running had a negligible effect on the performance of the PET scanner. The reduction of the SNR and homogeneity of the MRI images was less than 2% as the PET scanner was inserted to the MRI scanner and powered-on. High quality PET and MRI images of a human brain were obtained from simultaneous PET/MRI scans. The SIAT bPET scanner achieved a spatial resolution and sensitivity better than all MR-compatible brain PET scanners developed up to date. It can be used either as a standalone brain PET scanner or a PET insert placed inside a commercial whole-body MRI scanner to perform simultaneous PET/MRI imaging.

Novel radiation hard position sensitive detector using YAG:Ce fibers for ion beam instrumentation at FRIB

We are investigating the feasibility of a new detector concept for use in the beam line at the Facility for Rare Isotope Beams (FRIB). The detector is designed to withstand the high ion beam intensities and the high radiation environment while providing position, timing, and energy information. Based on the concept of a fiber detector, the device uses YAG:Ce crystals as sensing material, chosen for their extreme radiation tolerance to electromagnetic or hadronic exposure. The crystals are machined into long and thin rods which are laid out in orthogonal horizontal and vertical arrangements to obtain spatial sensitivity to impinging particles. The readout is performed at the extremities of the rods with strip Multi Pixel Photon Counters (MPPC) also referred to as Silicon Photomultipliers (SiPM) arrays model S13552 from Hamamatsu mounted on ribbon cables with connector ends.

Walk-through flat panel total-body PET: a patient-centered design for high throughput imaging at lower cost using DOI-capable high-resolution monolithic detectors

PurposeLong axial field-of-view (LAFOV) systems have a much higher sensitivity than standard axial field-of-view (SAFOV) PET systems for imaging the torso or full body, which allows faster and/or lower dose imaging. Despite its very high sensitivity, current total-body PET (TB-PET) throughput is limited by patient handling (positioning on the bed) and often a shortage of available personnel. This factor, combined with high system costs, makes it hard to justify the implementation of these systems for many academic and nearly all routine nuclear medicine departments. We, therefore, propose a novel, cost-effective, dual flat panel TB-PET system for patients in upright standing positions to avoid the time-consuming positioning on a PET-CT table; the walk-through (WT) TB-PET. We describe a patient-centered, flat panel PET design that offers very efficient patient throughput and uses monolithic detectors (with BGO or LYSO) with depth-of-interaction (DOI) capabilities and high intrinsic spatial resolution. We compare system sensitivity, component costs, and patient throughput of the proposed WT-TB-PET to a SAFOV (= 26 cm) and a LAFOV (= 106 cm) LSO PET systems.MethodsPatient width, height (= top head to start of thighs) and depth (= distance from the bed to front of patient) were derived from 40 randomly selected PET-CT scans to define the design dimensions of the WT-TB-PET. We compare this new PET system to the commercially available Siemens Biograph Vision 600 (SAFOV) and Siemens Quadra (LAFOV) PET-CT in terms of component costs, system sensitivity, and patient throughput. System cost comparison was based on estimating the cost of the two main components in the PET system (Silicon Photomultipliers (SiPMs) and scintillators). Sensitivity values were determined using Gate Monte Carlo simulations. Patient throughput times (including CT and scout scan, patient positioning on bed and transfer) were recorded for 1 day on a Siemens Vision 600 PET. These timing values were then used to estimate the expected patient throughput (assuming an equal patient radiotracer injected activity to patients and considering differences in system sensitivity and time-of-flight information) for WT-TB-PET, SAFOV and LAFOV PET.ResultsThe WT-TB-PET is composed of two flat panels; each is 70 cm wide and 106 cm high, with a 50-cm gap between both panels. These design dimensions were justified by the patient sizes measured from the 40 random PET-CT scans. Each panel consists of 14 × 20 monolithic BGO detector blocks that are 50 × 50 × 16 mm in size and are coupled to a readout with 6 × 6 mm SiPMs arrays. For the WT-TB-PET, the detector surface is reduced by a factor of 1.9 and the scintillator volume by a factor of 2.2 compared to LAFOV PET systems, while demonstrating comparable sensitivity and much better uniform spatial resolution (< 2 mm in all directions over the FOV). The estimated component cost for the WT-TB-PET is 3.3 × lower than that of a 106 cm LAFOV system and only 20% higher than the PET component costs of a SAFOV. The estimated maximum number of patients scanned on a standard 8-h working day increases from 28 (for SAFOV) to 53–60 (for LAFOV in limited/full acceptance) to 87 (for the WT-TB-PET). By scanning faster (more patients), the amount of ordered activity per patient can be reduced drastically: the WT-TB-PET requires 66% less ordered activity per patient than a SAFOV.ConclusionsWe propose a monolithic BGO or LYSO-based WT-TB-PET system with DOI measurements that departs from the classical patient positioning on a table and allows patients to stand upright between two flat panels. The WT-TB-PET system provides a solution to achieve a much lower cost TB-PET approaching the cost of a SAFOV system. High patient throughput is increased by fast patient positioning between two vertical flat panel detectors of high sensitivity. High spatial resolution (< 2 mm) uniform over the FOV is obtained by using DOI-capable monolithic scintillators.

Simulation of a neutron imaging detector prototype based on SiPM array readout

Neutron imaging technology as a means of non-destructive detection of materials is complementary to X-ray imaging. Silicon photomultiplier (SiPM), a new type of optical readout device, has overcome some shortcomings of traditional photomultiplier tube (PMT), such as high-power consumption, large volume, high price, uneven gain response, and inability to work in strong magnetic fields. Its application in the field of neutron detection will be an irresistible general trend. In this paper, a thermal neutron imaging detector based on 6LiF/ZnS scintillation screen and SiPM array readout was developed. The design of the detector geometry was optimized by geant4 Monte Carlo simulation software. The optimized detector was evaluated with a step wedge sample. The results show that the detector prototype with a 48 mm × 48 mm sensitive area can achieve about 38% detection efficiency and 0.26 mm position resolution when using a 300 μm thick 6LiF/ZnS scintillation screen and a 2 mm thick Bk7 optical guide coupled with SiPM array, and has good neutron imaging capability. It provides effective data support for developing high-performance imaging detectors applied to the China Spallation Neutron Source (CSNS).

Optimization With Simulated Annealing and Experimental Study of a Discretized Position Circuit (DPC) Network Using an Array of SiPMs

Arrays of tens or even hundreds of Silicon Photomultipliers (SiPMs) coupled to scintillators to build compact and robust position sensitive radiation detectors are becoming ubiquitous in nuclear medicine devices. In order to reduce the number of read-out electronic channels, and still be able to keep position information, multiplexing the SiPM signals with 2D resistor networks is fairly common. Good results are obtained with the DPC (Discretized Positioning Circuit) configuration. Even though it is a simple topology with a minimum number of discrete components, it yields good peak/valley ratios. However, it has the disadvantage that the network is asymmetric in X and Y directions, leading to different paths for the signal to reach the output depending on the position of the event. This causes the pulse shape to be also dependent on the position of the interaction in the detector, and creates a distortion (pincushion or barrel) of the position determined with center of energy algorithms. This effect can be partially remedied by a non-homogeneous choice of resistors in the network, but finding the best resistor values, in the case of large SiPM aggregations is very time consuming. We have developed a framework to optimize resistor values in DPC configurations to minimize position distortion and then impose that every SiPMs see an impedance to ground as similar as possible. We solved the DPC circuit and employed a simulated annealing algorithm to explore thousands of resistor combinations. The best combinations found in the computer were implemented in the laboratory confirming the results of the simulated annealing algorithm. In addition, we have verified that the optimized DPC network preserves the pulse shape to the extent that pulse shape discrimination makes it possible to disentangle two different scintillator layers (phoswich) of LYSO and GSO.

Low-cost and miniaturized temperature compensation system for nuclear applications

Facilities using nuclear radiation and detectors require stability of detector response irrespective of the ambient conditions. This stability of radiation detector output is crucial for applications requiring precise monitoring of radiation. The paper presents the development and performance validation of an analogue feedback circuit designed to compensate for the effect of temperature variations in Silicon Photomultiplier (SiPM) based detectors and measurement systems. The presented circuit uses feedback from a temperature sensor to enable a linear compensation to control the bias voltage for the charge pump-based bias supply. The circuit was tested using a scintillator coupled to a 2 × 2 array of SiPMs and tested using a Caesium-137 radioactive source for checking the stability of the detector output. The system was tested over a temperature range from 5 to 55 °C. Considering this broad range, this circuit was calibrated for different temperature ranges allowing the user to set the compensation depending on the temperature range of interest.

NEMA NU 1-2018 performance characterization and Monte Carlo model validation of the Cubresa Spark SiPM-based preclinical SPECT scanner

BackgroundThe Cubresa Spark is a novel benchtop silicon-photomultiplier (SiPM)-based preclinical SPECT system. SiPMs in SPECT significantly improve resolution and reduce detector size compared to preclinical cameras with photomultiplier tubes requiring highly magnifying collimators. The NEMA NU 1 Standard for Performance Measurements of Gamma Cameras provides methods that can be readily applied or extended to characterize preclinical cameras with minor modifications. The primary objective of this study is to characterize the Spark according to the NEMA NU 1-2018 standard to gain insight into its nuclear medicine imaging capabilities. The secondary objective is to validate a GATE Monte Carlo simulation model of the Spark for use in preclinical SPECT studies.MethodsNEMA NU 1-2018 guidelines were applied to characterize the Spark’s intrinsic, system, and tomographic performance with single- and multi-pinhole collimators. Phantoms were fabricated according to NEMA specifications with deviations involving high-resolution modifications. GATE was utilized to model the detector head with the single-pinhole collimator, and NEMA measurements were employed to tune and validate the model. Single-pinhole and multi-pinhole SPECT data were reconstructed with the Software for Tomographic Image Reconstruction and HiSPECT, respectively.ResultsThe limiting intrinsic resolution was measured as 0.85 mm owing to a high-resolution SiPM array combined with a 3 mm-thick scintillation crystal. The average limiting tomographic resolution was 1.37 mm and 1.19 mm for the single- and multi-pinhole collimators, respectively, which have magnification factors near unity at the center of rotation. The maximum observed count rate was 15,400 cps, and planar sensitivities of 34 cps/MBq and 150 cps/MBq were measured at the center of rotation for the single- and multi-pinhole collimators, respectively. All simulated tests agreed well with measurement, where the most considerable deviations were below 7%.ConclusionsNEMA NU 1-2018 standards determined that a SiPM detector mitigates the need for highly magnifying pinhole collimators while preserving detailed information in projection images. Measured and simulated NEMA results were highly comparable with differences on the order of a few percent, confirming simulation accuracy and validating the GATE model. Of the collimators initially provided with the Spark, the multi-pinhole collimator offers high resolution and sensitivity for organ-specific imaging of small animals, and the single-pinhole collimator enables high-resolution whole-body imaging of small animals.

Inter-crystal scattering event identification using a novel silicon photomultiplier signal multiplexing method

Objective. Identifying the inter-crystal scatter (ICS) events and recovering the first interaction position enables the accurate determination of the line-of-response in positron emission tomography (PET). However, conventional silicon photomultiplier (SiPM) signal multiplexing methods based on two-dimensional (2D) charge-division circuits do not allow the detection of multiple gamma-ray interaction positions in a scintillation array coupled with a SiPM array. In this study, we propose a novel multiplexing method that can restore all the individual channel data from a smaller number of multiplexed channels using high-pass filters and neural networks. Approach. The number of output channels is reduced by summing the SiPM signals that have passed through high-pass filters with different time constants. Then, the signal amplitude of each SiPM channel is restored from the combined signal using an artificial neural network. This study explains the principle of this method in detail and demonstrates the results using 4:1 multiplexing as an example. The usefulness of this method was also demonstrated by its application in the identification of ICS events in 1-to-1 coupled LSO-SiPM PET detectors. Main results. The artificial neural network enabled accurate energy estimation for each SiPM channel. One of the high-pass filter sets with the lowest Cramér–Rao lower bound provided the best results, yielding R 2 value of 0.99 between the true and estimated signals. The energy and flood histograms generated using the best-estimated signals were in good agreement with the ground truth. Additionally, the proposed method accurately estimated 2D energy deposit distribution in the LSO crystal array, allowing ICS event identification. Significance. The proposed method is potentially useful for ICS event recovery with a reduced number of array signal readout channels from a SiPM array.

A SiPM-based dual and triple coincidence system for positron annihilation lifetime measurement

Positron annihilation lifetime (PAL) spectroscopy is a powerful non-destructive method to study defects in materials. Silicon photomultipliers (SiPMs) have emerged as promising photodetector alternatives for PAL systems. However, further research is needed to fully optimize SiPM arrays for PAL applications. In this study, a dual and triple coincidence system has been developed based on four 1 × 4 SiPM arrays with resistor-chain readout, and initial results of PAL measurement have been obtained. A pixel-by-pixel time shift correction method was proposed and successfully applied using triple γ coincidence for summing 128 PAL spectra in one measurement. The system provides position, timing, and energy information for both 1275 and 511 keV γ-rays. The use of SiPM arrays and the pixel-by-pixel time shift correction method have enabled precise and reliable measurements of PALs in single-crystal silicon and yttria-stabilized zirconia samples. The developed SiPM-array-based PAL system also offers a technical solution to measure angular correlations of positron annihilation radiation, with the potential for further improvements.

Compact Back-End Electronics with Temperature Compensation and Efficient Data Management for In Situ SiPM-Based Radiation Detection.

A compact back-end interface for silicon photomultipliers (SiPMs) implementing Zener diode-based temperature compensation has been developed for the remote detection of beta and gamma radiation. Remote detection is facilitated by the development of an efficient data management system utilising MySQL database storage for recording periodic spectra data for wireless access over a private Wi-Fi network. A trapezoidal peak shaping algorithm has been implemented on an FPGA for the continuous conversation of pulses from the SiPM, signifying the detection of a radiological particle, into spectra. This system has been designed to fit within a 46 mm cylindrical diameter for in situ characterization, and can be attached to one or more SiPMs used in conjunction with a range of scintillators. LED blink tests have been used to optimise the trapezoidal shaper coefficients to maximise the resolution of the recorded spectra. Experiments with an array of SiPMs integrated with a NaI(Tl) scintillator exposed to sealed sources of Co-60, Cs-137, Na-22 and Am-241 have shown that the detector achieves a peak efficiency of 27.09 ± 0.13% for a gamma peak at 59.54 keV produced by Am-241, and a minimum energy resolution (Delta E/E) of 4.27 ± 1.16% for the 1332.5 keV gamma peak from Co-60.