Atmospheric Radiation Measurement Mobile Facility Research Articles

Simulating Mixed‐Phase Open Cellular Clouds Observed During COMBLE: Evaluation of Parameterized Turbulence Closure

AbstractMarine cold‐air outbreaks, or CAOs, are airmass transformations whereby relatively cold boundary layer (BL) air is transported over relatively warm water. To more deeply understand BL and mixed‐phase cloud properties during CAO conditions, the Cold‐Air Outbreaks in the Marine Boundary Layer Experiment (COMBLE) took place from late 2019 into early 2020. During COMBLE, the U.S. Department of Energy's first Atmospheric Radiation Measurement Mobile Facility (AMF1) was deployed to Andenes, Norway, far downstream (∼1,000 km) from the Arctic pack ice. This study examines the two most intense CAOs sampled at the AMF1 site. The observed BL structures are open cellular with high (∼3–5 km) and cold (−30 to −50 C) cloud tops, and they often have pockets of high liquid water paths (LWPs; up to ∼1,000 g ) associated with strong updrafts and enhanced turbulence. We use a high‐resolution mesoscale model to explore how well four turbulence closure methods represent open cellular clouds. After applying a radar simulator to model outputs for direct evaluation, cloud top properties agree well with AMF1 observations (within ∼10%), but radar reflectivity and LWP agreement is more variable. Results suggest that the turbulent Prandtl number may play an important role for the simulated BL and cloud properties. All simulations produce enhanced precipitation rates that are well‐correlated with a cloud transition. Finally, the eddy‐diffusivity/mass‐flux approach produces the deepest cloud layer and therefore the largest and most coherent cellular structures. We recommend the use of a non‐local turbulence closure approach to better capture turbulent processes in intense CAOs.

Hyperspectral Infrared Observations of Arctic Snow, Sea Ice, and Non-Frozen Ocean from the RV Polarstern during the MOSAiC Expedition October 2019 to September 2020

This study highlights hyperspectral infrared observations from the Marine-Atmospheric Emitted Radiance Interferometer (M-AERI) collected as part of the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) deployment on the icebreaker RV Polarstern during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition from October 2019 to September 2020. The ARM M-AERI directly measures the infrared radiance emission spectrum between 520 cm−1 and 3000 cm−1 (19.2–3.3 μm) at 0.5 cm−1 spectral resolution. These ship-based observations provide a valuable set of radiance data for the modeling of snow/ice infrared emission as well as validation data for the assessment of satellite soundings. Remote sensing using hyperspectral infrared observations provides valuable information on sea surface properties (skin temperature and infrared emissivity), near-surface air temperature, and temperature lapse rate in the lowest kilometer. Comparison of the M-AERI observations with those from the DOE ARM meteorological tower and downlooking infrared thermometer are generally in good agreement with some notable differences. Operational satellite soundings from the NOAA-20 satellite were also assessed using ARM radiosondes launched from the RV Polarstern and measurements of the infrared snow surface emission from the M-AERI showing reasonable agreement.

Vertical Structure and Ice Production Processes of Shallow Convective Postfrontal Clouds over the Southern Ocean in MARCUS. Part I: Observational Study

Abstract A study of the vertical structure of postfrontal shallow clouds in the marine boundary layer over the Southern Ocean is presented. The central question of this two-part study regards cloud phase (liquid/ice) of precipitation, and the associated growth mechanisms. In this first part, data from the Measurements of Aerosols, Radiation, and Clouds over the Southern Ocean (MARCUS) field campaign are analyzed, starting with a 75-h case with continuous sea surface-based thermal instability, modest surface heat fluxes, an open-cellular mesoscale organization, and very few ice nucleating particles (INPs). The clouds are mostly precipitating and shallow (tops mostly around 2 km above sea level), with weak up- and downdrafts, and with cloud-top temperatures generally around −18° to −10°C. The case study is extended to three other periods of postfrontal shallow clouds in MARCUS. While abundant supercooled liquid water is commonly present, an experimental cloud-phase algorithm classifies nearly two-thirds of clouds in the 0° to −5°C layer as containing ice (cloud ice, snow, or mixed phase), implying that much of the precipitation grows through cold-cloud processes. The best predictors of ice presence are cloud-top temperature, cloud depth, and INP concentration. Measures of convective activity and turbulence are found to be poor indicators of ice presence in the studied environment. The water-phase distribution in this cloud regime is explored through numerical simulations in Part II. Significance Statement Climate models generally predict a lower albedo than observed over the Southern Ocean, and this is largely attributed to a lack of cloudiness, especially in the postfrontal cold sector of midlatitude cyclones. This in turn may be due to an excess of ice in these simulated clouds, resulting in rapid precipitation fallout and an overly brief cloud lifespan. The objective of this study is to examine whether shallow postfrontal clouds over the Southern Ocean are dominated by supercooled drops, or by snow and ice, using data collected by a U.S. Department of Energy Atmospheric Radiation Measurement Mobile Facility deployed aboard an Australian Antarctic supply vessel. We find that these clouds contain much supercooled liquid, even though cloud-top temperatures generally are around −18° to −8°C, and that about two-thirds of the clouds just above the freezing level contain ice. Much of the precipitation appears to grow through cold-cloud processes above the freezing level, rather than drizzle/rain. Updrafts and/or turbulence in convection or in cloud-top generating cells do not initiate much ice, compared to observations elsewhere in a similar temperature range. This may be attributable to the extremely low concentration of ice nucleating particles in this environment. Ultimately, the deepest clouds with the coldest cloud tops are most likely to be ice dominated.

Surface-based observations of cold-air outbreak clouds during the COMBLE field campaign

Abstract. Cold-air outbreaks (CAOs) are characterized by extreme air–sea energy exchanges and low-level convective clouds over large areas in the high-latitude oceans. As such, CAOs are an important component of the Earth's climate system. The CAOs in the Marine Boundary Layer Experiment (COMBLE) deployment of the US Department of Energy Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) provided the first comprehensive view of CAOs using a suite of ground-based observations at the northern coast of Norway. Here, cloud and precipitation observations from 13 CAO cases during COMBLE are analyzed. A vertical air motion retrieval technique is applied to the Ka-band ARM Zenith-pointing Radar (KAZR) observations. The CAO cumulus clouds are characterized by strong updrafts with magnitudes between 2–8 m s−1, vertical extents of 1–3 km, and horizontal scales of 0.25–3 km. A strong relationship between our vertical air velocity retrievals and liquid water path (LWP) measurements is found. The LWP measurements exceed 1 kg m−2 in strong updraft areas, and the vertical extent of the updraft correlates well with the LWP values. The CAO cumulus clouds exhibit eddy dissipation rate values between 10−3 and 10−2 m2 s−3 in the lowest 10 km of the atmosphere, and using a radar Doppler spectra technique, evidence of secondary ice production is found during one of the cases.

Intercomparison of airborne and surface-based measurements during the CLARIFY, ORACLES and LASIC field experiments

Abstract. Data are presented from intercomparisons between two research aircraft, the FAAM BAe-146 and the NASA Lockheed P3, and between the BAe-146 and the surface-based DOE (Department of Energy) ARM (Atmospheric Radiation Measurement) Mobile Facility at Ascension Island (8∘ S, 14.5∘ W; a remote island in the mid-Atlantic). These took place from 17 August to 5 September 2017, during the African biomass burning (BB) season. The primary motivation was to give confidence in the use of data from multiple platforms with which to evaluate numerical climate models. The three platforms were involved in the CLouds–Aerosol–Radiation Interaction and Forcing for Year 2017 (CLARIFY-2017), ObseRvations of Aerosols above CLouds and their intEractionS (ORACLES), and Layered Atlantic Smoke and Interactions with Clouds (LASIC) field experiments. Comparisons from flight segments on 6 d where the BAe-146 flew alongside the ARM facility on Ascension Island are presented, along with comparisons from the wing-tip-to-wing-tip flight of the P3 and BAe-146 on 18 August 2017. The intercomparison flight sampled a relatively clean atmosphere overlying a moderately polluted boundary layer, while the six fly-bys of the ARM site sampled both clean and polluted conditions 2–4 km upwind. We compare and validate characterisations of aerosol physical, chemical and optical properties as well as atmospheric radiation and cloud microphysics between platforms. We assess the performance of measurement instrumentation in the field, under conditions where sampling conditions are not as tightly controlled as in laboratory measurements where calibrations are performed. Solar radiation measurements compared well enough to permit radiative closure studies. Optical absorption coefficient measurements from all three platforms were within uncertainty limits, although absolute magnitudes were too low (<10 Mm−1) to fully support a comparison of the absorption Ångström exponents. Aerosol optical absorption measurements from airborne platforms were more comparable than aircraft-to-ground observations. Scattering coefficient observations compared adequately between airborne platforms, but agreement with ground-based measurements was worse, potentially caused by small differences in sampling conditions or actual aerosol population differences over land. Chemical composition measurements followed a similar pattern, with better comparisons between the airborne platforms. Thermodynamics, aerosol and cloud microphysical properties generally agreed given uncertainties.

The COMBLE Campaign: A Study of Marine Boundary Layer Clouds in Arctic Cold-Air Outbreaks

Abstract One of the most intense air mass transformations on Earth happens when cold air flows from frozen surfaces to much warmer open water in cold-air outbreaks (CAOs), a process captured beautifully in satellite imagery. Despite the ubiquity of the CAO cloud regime over high-latitude oceans, we have a rather poor understanding of its properties, its role in energy and water cycles, and its treatment in weather and climate models. The Cold-Air Outbreaks in the Marine Boundary Layer Experiment (COMBLE) was conducted to better understand this regime and its representation in models. COMBLE aimed to examine the relations between surface fluxes, boundary layer structure, aerosol, cloud, and precipitation properties, and mesoscale circulations in marine CAOs. Processes affecting these properties largely fall in a range of scales where boundary layer processes, convection, and precipitation are tightly coupled, which makes accurate representation of the CAO cloud regime in numerical weather prediction and global climate models most challenging. COMBLE deployed an Atmospheric Radiation Measurement Mobile Facility at a coastal site in northern Scandinavia (69°N), with additional instruments on Bear Island (75°N), from December 2019 to May 2020. CAO conditions were experienced 19% (21%) of the time at the main site (on Bear Island). A comprehensive suite of continuous in situ and remote sensing observations of atmospheric conditions, clouds, precipitation, and aerosol were collected. Because of the clouds’ well-defined origin, their shallow depth, and the broad range of observed temperature and aerosol concentrations, the COMBLE dataset provides a powerful modeling testbed for improving the representation of mixed-phase cloud processes in large-eddy simulations and large-scale models.

Utilizing a Storm-Generating Hotspot to Study Convective Cloud Transitions: The CACTI Experiment

AbstractThe Cloud, Aerosol, and Complex Terrain Interactions (CACTI) field campaign was designed to improve understanding of orographic cloud life cycles in relation to surrounding atmospheric thermodynamic, flow, and aerosol conditions. The deployment to the Sierras de Córdoba range in north-central Argentina was chosen because of very frequent cumulus congestus, deep convection initiation, and mesoscale convective organization uniquely observable from a fixed site. The C-band Scanning Atmospheric Radiation Measurement (ARM) Precipitation Radar was deployed for the first time with over 50 ARM Mobile Facility atmospheric state, surface, aerosol, radiation, cloud, and precipitation instruments between October 2018 and April 2019. An intensive observing period (IOP) coincident with the RELAMPAGO field campaign was held between 1 November and 15 December during which 22 flights were performed by the ARM Gulfstream-1 aircraft. A multitude of atmospheric processes and cloud conditions were observed over the 7-month campaign, including numerous orographic cumulus and stratocumulus events; new particle formation and growth producing high aerosol concentrations; drizzle formation in fog and shallow liquid clouds; very low aerosol conditions following wet deposition in heavy rainfall; initiation of ice in congestus clouds across a range of temperatures; extreme deep convection reaching 21-km altitudes; and organization of intense, hail-containing supercells and mesoscale convective systems. These comprehensive datasets include many of the first ever collected in this region and provide new opportunities to study orographic cloud evolution and interactions with meteorological conditions, aerosols, surface conditions, and radiation in mountainous terrain.

An Observational Comparison of Level of Neutral Buoyancy and Level of Maximum Detrainment in Tropical Deep Convective Clouds

AbstractTropical deep convective clouds are important drivers of large‐scale atmospheric circulation representing the main vertical transport pathway through the depth of the troposphere for heat, momentum, water, and chemical species. The strength and depth of this transport are impacted by the convective updraft size and intensity that are driven by buoyancy, dynamical forcing, and mixing of environmental air, that is, entrainment. In this study, we identify tropical deep convective systems with well‐defined forward anvils using Atmospheric Radiation Measurement (ARM) ground‐based profiling radars, at three ARM fixed sites in the Tropical Western Pacific (TWP; i.e., Manus, Nauru, and Darwin) and three ARM Mobile Facility deployments in Niamey, Niger; Gan Island, Maldives; and Manacapuru, Brazil. We use the difference between the level of neutral buoyancy (LNB) and the level of maximum detrainment (LMD) as a proxy for the effective bulk convective entrainment (εproxy). The LNB, the theoretical height that a parcel raised above the level of free convection would reach with no mixing, is calculated based on preconvection radiosonde measurements using parcel theory. The LMD is the height of the maximum reflectivity observed in forward anvil clouds by profiling radars. Deep convective systems over the TWP show higher LNBs that extend to 16.3 km on average and larger εproxy (median value of LNB minus LMD up to 6.5 km) compared to their continental counterparts in the Amazon and West Africa. Oceanic conditions show larger convective available potential energy (CAPE) coupled with higher moisture at low levels, which favors larger εproxy. In contrast, continental cases initiate and develop, under high convective inhibition, steeper environmental lapse rate, and high wind shear conditions, which show smaller offset between LNB and LMD. Deep convective cases that promote significant cold pools at the surface experience less εproxy. Using a Random Forest regression algorithm, CAPE is associated with the highest feature importance score for predicting convective εproxy, followed by low‐level relative humidity. For continental cases, the low‐level wind shear also indicates higher importance.

Intercomparison of Integrated Water Vapor Measurements at High Latitudes from Co-Located and Near-Located Instruments

Data from global positioning system (GPS) ground-based receivers, ground-based microwave radiometers (MWRs), and radiosondes (RS) at two high-latitude sites were compared. At one site, the North Slope of Alaska (NSA), Barrow, Alaska (USA), the instruments were co-located, while at the other site, the second ARM Mobile Facility (AMF2), Hyytiälä, Finland, the GPS receiver was located about 20 km away from the MWRs and RS. Differences between the GPS-derived integrated water vapor (IWV) and the other three instruments were analyzed in terms of mean differences and standard deviation. A comparison of co-located and near-located independently calibrated instruments allowed us to isolate issues that may be specific to a single system and, to some extent, to isolate the effects of the distance between the GPS receiver and the remaining instruments. The results showed that at these two high-latitude sites, when the IWV was less than 15 kg/m2, the GPS agreed with other instruments within 0.5–0.7 kg/m2. When the variability of water vapor was higher, mostly in the summer months, the GPS agreed with other instruments within 0.8–1 kg/m2. The total random uncertainty between the GPS and the other systems was of the order of 0.6–1 kg/m2 and was the dominant effect when the IWV was higher than 15 kg/m2.

Combining airborne in situ and ground-based lidar measurements for attribution of aerosol layers

Abstract. Understanding the distribution of aerosol layers is important for determining long-range transport and aerosol radiative forcing. In this study we combine airborne in situ measurements of aerosol with data obtained by a ground-based high spectral resolution lidar (HSRL) and radiosonde profiles to investigate the temporal and vertical variability of aerosol properties in the lower troposphere. The HSRL was deployed in Hyytiälä, southern Finland, from January to September 2014 as a part of the U.S. DOE ARM (Atmospheric Radiation Measurement) mobile facility during the BAECC (Biogenic Aerosols – Effects on Cloud and Climate) Campaign. Two flight campaigns took place in April and August 2014 with instruments measuring the aerosol size distribution from 10 nm to 5 µm at altitudes up to 3800 m. Two case studies with several aerosol layers present were selected from the flight campaigns for further investigation: one clear-sky and one partly cloudy case. During the clear-sky case, turbulent mixing ensured small temporal and spatial variability in the measured aerosol size distribution in the boundary layer, whereas mixing was not as homogeneous in the boundary layer during the partly cloudy case. The elevated layers exhibited larger temporal and spatial variability in aerosol size distribution, indicating a lack of mixing. New particle formation was observed in the boundary layer during the clear-sky case, and nucleation mode particles were also seen in the elevated layers that were not mixing with the boundary layer. Interpreting local measurements of elevated layers in terms of long-range transport can be achieved using back trajectories from Lagrangian models, but care should be taken in selecting appropriate arrival heights, since the modelled and observed layer heights did not always coincide. We conclude that higher confidence in attributing elevated aerosol layers to their air mass origin is attained when back trajectories are combined with lidar and radiosonde profiles.

A Bird’s-Eye View: Development of an Operational ARM Unmanned Aerial Capability for Atmospheric Research in Arctic Alaska

AbstractThorough understanding of aerosols, clouds, boundary layer structure, and radiation is required to improve the representation of the Arctic atmosphere in weather forecasting and climate models. To develop such understanding, new perspectives are needed to provide details on the vertical structure and spatial variability of key atmospheric properties, along with information over difficult-to-reach surfaces such as newly forming sea ice. Over the last three years, the U.S. Department of Energy (DOE) has supported various flight campaigns using unmanned aircraft systems [UASs, also known as unmanned aerial vehicles (UAVs) and drones] and tethered balloon systems (TBSs) at Oliktok Point, Alaska. These activities have featured in situ measurements of the thermodynamic state, turbulence, radiation, aerosol properties, cloud microphysics, and turbulent fluxes to provide a detailed characterization of the lower atmosphere. Alongside a suite of active and passive ground-based sensors and radiosondes deployed by the DOE Atmospheric Radiation Measurement (ARM) program through the third ARM Mobile Facility (AMF-3), these flight activities demonstrate the ability of such platforms to provide critically needed information. In addition to providing new and unique datasets, lessons learned during initial campaigns have assisted in the development of an exciting new community resource.

The Ascension Island Boundary Layer in the Remote Southeast Atlantic is Often Smoky

AbstractObservations from June to October 2016, from a surface‐based ARM Mobile Facility deployment on Ascension Island (8°S, 14.5°W) indicate that refractory black carbon (rBC) is almost always present within the boundary layer. The rBC mass concentrations, light absorption coefficients, and cloud condensation nuclei concentrations vary in concert and synoptically, peaking in August. Light absorption coefficients at three visible wavelengths as a function of rBC mass are approximately double that calculated from black carbon in lab studies. A spectrally‐flat absorption angstrom exponent suggests most of the light absorption is from lens‐coated black carbon. The single‐scattering‐albedo increases systematically from August to October in both 2016 and 2017, with monthly means of 0.78 ± 0.02 (August), 0.81 ± 0.03 (September), and 0.83 ± 0.03 (October) at the green wavelength. Boundary layer aerosol loadings are only loosely correlated with total aerosol optical depth, with smoke more likely to be present in the boundary layer earlier in the biomass burning season, evolving to smoke predominantly present above the cloud layers in September–October, typically resting upon the cloud top inversion. The time period with the campaign‐maximum near‐surface light absorption and column aerosol optical depth, on 13–16 August 2016, is investigated further. Backtrajectories that indicate more direct boundary layer transport westward from the African continent is central to explaining the elevated surface aerosol loadings.

Retrieving Mean Temperature of Atmospheric Liquid Water Layers Using Microwave Radiometer Measurements

AbstractA remote sensing method to retrieve the mean temperature of cloud liquid using ground-based microwave radiometer measurements is evaluated and tested by comparisons with direct cloud temperature information inferred from ceilometer cloud-base measurements and temperature profiles from radiosonde soundings. The method is based on the dependence of the ratio of cloud optical thicknesses at W-band (~90 GHz) and Ka-band (~30 GHz) frequencies on cloud liquid temperature. This ratio is obtained from total optical thicknesses inferred from radiometer measurements of brightness temperatures after accounting for the contributions from oxygen and water vapor. This accounting is done based on the radiometer-based retrievals of integrated water vapor amount and temperature and pressure measurements at the surface. The W–Ka-band ratio method is applied to the measurements from a three-channel (90, 31.4, and 23.8 GHz) microwave radiometer at the U.S. Department of Energy Atmospheric Radiation Measurement Mobile Facility at Oliktok Point, Alaska. The analyzed events span conditions from warm stratus clouds with temperatures above freezing to mixed-phase clouds with supercooled liquid water layers. Intercomparisons of radiometer-based cloud liquid temperature retrievals with estimates from collocated ceilometer and radiosonde measurements indicated on average a standard deviation of about 3.5°C between the two retrieval types in a wide range of cloud temperatures, from warm liquid clouds to mixed-phase clouds with supercooled liquid and liquid water paths greater than 50 g m−2. The three-channel microwave radiometer–based method has a broad applicability, since it requires neither the use of active sensors to locate the boundaries of liquid cloud layers nor information on the vertical profile of temperature.

First surface-based estimation of the aerosol indirect effect over a site in southeastern China

The deployment of the U.S. Atmospheric Radiation Measurement mobile facility in Shouxian from May to December 2008 amassed the most comprehensive set of measurements of atmospheric, surface, aerosol, and cloud variables in China. This deployment provided a unique opportunity to investigate the aerosol–cloud interactions, which are most challenging and, to date, have not been examined to any great degree in China. The relationship between cloud droplet effective radius (CER) and aerosol index (AI) is very weak in summer because the cloud droplet growth is least affected by the competition for water vapor. Mean cloud liquid water path (LWP) and cloud optical depth (COD) significantly increase with increasing AI in fall. The sensitivities of CER and LWP to aerosol loading increases are not significantly different under different air mass conditions. There is a significant correlation between the changes in hourly mean AI and the changes in hourly mean CER, LWP, and COD. The aerosol first indirect effect (FIE) is estimated in terms of relative changes in both CER (FIECER) and COD (FIECOD) with changes in AI for different seasons and air masses. FIECOD and FIECER are similar in magnitude and close to the typical FIE value of ∼ 0.23, and do not change much between summer and fall or between the two different air mass conditions. Similar analyses were done using spaceborne Moderate Resolution Imaging Spectroradiometer data. The satellite-derived FIE is contrary to the FIE estimated from surface retrievals and may have large uncertainties due to some inherent limitations.

Cloud characteristics, thermodynamic controls and radiative impacts during the Observations and Modeling of the Green Ocean Amazon (GoAmazon2014/5) experiment

Abstract. Routine cloud, precipitation and thermodynamic observations collected by the Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) and Aerial Facility (AAF) during the 2-year US Department of Energy (DOE) ARM Observations and Modeling of the Green Ocean Amazon (GoAmazon2014/5) campaign are summarized. These observations quantify the diurnal to large-scale thermodynamic regime controls on the clouds and precipitation over the undersampled, climatically important Amazon basin region. The extended ground deployment of cloud-profiling instrumentation enabled a unique look at multiple cloud regimes at high temporal and vertical resolution. This longer-term ground deployment, coupled with two short-term aircraft intensive observing periods, allowed new opportunities to better characterize cloud and thermodynamic observational constraints as well as cloud radiative impacts for modeling efforts within typical Amazon wet and dry seasons.

Atmospheric Ice Particle Shape Estimates from Polarimetric Radar Measurements and In Situ Observations

AbstractA remote sensing approach to retrieve the degree of nonsphericity of ice hydrometeors using scanning polarimetric Ka-band radar measurements from a U.S. Department of Energy Atmospheric Radiation Measurement (ARM) Program cloud radar operated in an alternate transmission–simultaneous reception mode is introduced. Nonsphericity is characterized by aspect ratios representing the ratios of particle minor-to-major dimensions. The approach is based on the use of a circular depolarization ratio (CDR) proxy reconstructed from differential reflectivity ZDR and copolar correlation coefficient ρhυ linear polarization measurements. Essentially combining information contained in ZDR and ρhυ, CDR-based retrievals of aspect ratios are fairly insensitive to hydrometeor orientation if measurements are performed at elevation angles of around 40°–50°. The suggested approach is applied to data collected using the third ARM Mobile Facility (AMF3), deployed to Oliktok Point, Alaska. Aspect ratio retrievals were also performed using ZDR measurements that are more strongly (compared to CDR) influenced by hydrometeor orientation. The results of radar-based retrievals are compared with in situ measurements from the tethered balloon system (TBS)-based video ice particle sampler and the ground-based multiangle snowflake camera. The observed ice hydrometeors were predominantly irregular-shaped ice crystals and aggregates, with aspect ratios varying between approximately 0.3 and 0.8. The retrievals assume that particle bulk density influencing (besides the particle shape) observed polarimetric variables can be deduced from the estimates of particle characteristic size. Uncertainties of CDR-based aspect ratio retrievals are estimated at about 0.1–0.15. Given these uncertainties, radar-based retrievals generally agreed with in situ measurements. The advantages of using the CDR proxy compared to the linear depolarization ratio are discussed.

Areal-Averaged Spectral Surface Albedo in an Atlantic Coastal Area: Estimation from Ground-Based Transmission

Tower-based data combined with high-resolution satellite products have been used to produce surface albedo at various spatial scales over land. Because tower-based albedo data are available at only a few sites, surface albedos using these combined data are spatially limited. Moreover, tower-based albedo data are not representative of highly heterogeneous regions. To produce areal-averaged and spectrally-resolved surface albedo for regions with various degrees of surface heterogeneity, we have developed a transmission-based retrieval and demonstrated its feasibility for relatively homogeneous land surfaces. Here, we demonstrate its feasibility for a highly heterogeneous coastal region. We use the atmospheric transmission measured during a 19-month period (June 2009–December 2010) by a ground-based Multi-Filter Rotating Shadowband Radiometer (MFRSR) at five wavelengths (0.415, 0.5, 0.615, 0.673 and 0.87 µm) at the Department of Energy’s Atmospheric Radiation Measurement (ARM) Mobile Facility (AMF) site located on Graciosa Island. We compare the MFRSR-retrieved areal-averaged surface albedo with albedo derived from Moderate Resolution Imaging Spectroradiometer (MODIS) observations, and also a composite-based albedo. We demonstrate that these three methods produce similar spectral signatures of surface albedo; however, the MFRSR-retrieved albedo, is higher on average (≤0.04) than the MODIS-based areal-averaged surface albedo and the largest difference occurs in winter.

Inter-comparisons of marine boundary layer cloud properties from the ARM CAP-MBL campaign and two MODIS cloud products.

From April 2009 to December 2010, the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) program carried out an observational field campaign on Graciosa Island, targeting the marine boundary layer (MBL) clouds over the Azores region. In this paper, we present an inter-comparison of the MBL cloud properties, namely, cloud liquid water path (LWP), cloud optical thickness (COT) and cloud-droplet effective radius (CER), among retrievals from the ARM mobile facility (AMF) and two Moderate Resolution Spectroradiometer (MODIS) cloud products (GSFC-MODIS and CERES-MODIS). A total of 63 daytime single-layer MBL cloud cases are selected for inter-comparison. Comparison of collocated retrievals indicates that the two MODIS cloud products agree well on both COT and CER retrievals, with the correlation coefficient R>0.95. despite their significant difference in spatial sampling. In both MODIS products, the CER retrievals based on the 2.1 µm band (CER2.1) is significantly smaller than that based on the 3.7 µm band (CER3.7). The GSFC-MODIS cloud product is collocated and compared with ground-based ARM observations at several temporal-spatial scales. In general, the correlation increases with more precise collocation. For the 63 selected MBL cloud cases, the GSFC-MODIS LWP and COT retrievals agree reasonably well with the ground-based observations with no apparent bias and correlation coefficient R around 0.85 and 0.70, respectively. However, GSFC-MODIS CER3.7 and CER2.1 retrievals have a lower correlation (R~0.5) with the ground-based retrievals. For the 63 selected cases, they are on average larger than ground observations by about 1.5 µm and 3.0 µm, respectively. Taking into account that the MODIS CER retrievals are only sensitive to cloud top reduces the bias only by 0.5 µm.

The performance of the EarthCARE Cloud Profiling Radar in marine stratiform clouds

AbstractMarine stratiform clouds are a challenging target for spaceborne radars due to their proximity to Earth's surface, limited vertical extent, and low radar reflectivity. The joint European‐Japanese Earth Clouds, Aerosol and Radiation Explorer (EarthCARE) mission is scheduled for launch in 2019 and features the first atmospheric Cloud Profiling Radar (CPR) with Doppler capability in space. Here the performance of the CPR in (i) detecting these clouds and their boundaries and (ii) measuring the Doppler velocities of drizzle particles is evaluated. Extensive observations from the Atmospheric Radiation Measurement Mobile Facility in marine stratus regimes are used as input to an EarthCARE CPR simulator and to compare the resulting reflectivity factors, Doppler velocities, and cloud detections. Cloud detection of the CPR is 70–80% that of the ground‐based radars, depending upon integration length and feature mask configuration. For clouds entirely contained within the surface clutter, detection is limited but is predicted to be an order of magnitude greater for the EarthCARE CPR than for CloudSat due to the improved range sampling rate of the former. The EarthCARE‐CPR range resolution is found to introduce cloud top height and reflectivity biases of +100 m (equal to the range sampling rate) and +1.3 dB; by applying a constrained linear inversion to the range resolution, these are reduced to 30 m and 0.1 dB, respectively. The analysis indicates that a velocity uncertainty of 0.5 ms−1 is achievable through either a 5 km along‐track integration or a combination of matched spatial filters and 1 km along‐track integration.

Quantifying cloud base updraft speeds of marine stratocumulus from cloud top radiative cooling

AbstractMarine stratocumulus clouds play a significant role in the Earth's radiation budget. The updrafts at cloud base (Wb) govern the supersaturation and therefore the activation of cloud condensation nuclei, which modifies the cloud and precipitation properties. A statistically significant relationship between Wb and cloud top radiative cooling rate (CTRC) is found from the measurements of the Department of Energy's Atmospheric Radiation Measurement Mobile Facility on board a ship sailing between Honolulu and Los Angeles. A similar relation was found on Graciosa Island but with greater scatter and weaker correlation presumably due to the island effect. Based on the relation, we are able to estimate the cloud base updrafts using a simple formula: Wb = −0.44 × CTRC + 22.30 ± 13, where the Wb and CTRC have units of cm/s and W/m2, respectively. This quantification can be utilized in satellite remote sensing and parameterizations of Wb in general circulation models.