Aqueous Dispersions Research Articles

Tuning Local Order in Starch Nanoparticles Exploiting Nonsolvency with "Green" Solvents.

Starch is a renewable biopolymer that can be sourced from agricultural waste and used to produce nanoparticles (SNPs). In particular, amorphous SNPs have potential application in numerous fields, including the consolidation of weakened paintings in the cultural heritage preservation. Starch dissolution followed by nanoprecipitation in nonsolvents is an advantageous synthetic route, but new methodologies are needed to feasibly control the physicochemical properties of the SNPs. Here, we explored nanoprecipitation by nonsolvency using a set of "green" solvents to obtain amorphous SNPs, rather than starch nanocrystals already reported in the literature. The effect of the nonsolvent on the ordering of polymer chains in the obtained SNPs was studied. The recovery of local order (e.g., isolated V-type helices) after dissolution was shown to depend on the type of solvents used in the dissolution and precipitation steps, while long-range order (extended arrays of helices) is lost. Aqueous dispersions of the SNPs provided effective consolidation of powdery painted layers, showing that the selection of particle synthetic routes can be dictated by sustainability and scalability criteria. These "green" formulations are candidates as new consolidants in art preservation, and the possibility of tuning local order in amorphous starch assemblies might also impact fields like food chemistry, pharmaceutics, and nanocomposites, where SNPs with tunable amorphousness are more advantageous than nanocrystals.

Oral Lubrication, Xerostomia, and Advanced Macromolecular Lubricants for Treatment of Dry Mouth

Dry mouth, also known as xerostomia, is a condition in which insufficient or ineffective saliva does not provide sufficient oral lubrication. The severity of this condition can vary from a mild discomfort to a debilitating condition that greatly impairs patients’ lives. Xerostomia arises as a side effect of various medications, diseases, radiation therapy, chemotherapy, or nerve damage. Various aqueous dispersions of macromolecules have been proposed to assist or replace the saliva in these patients. It is vital that these macromolecules have ample lubricity and water retention properties while showing long-lasting efficacy. The emphasis of this review is to provide a general overview on lubricating macromolecules that have been clinically used or reported in the literature as potential replacements for saliva. These include various natural or synthetic polymers, proteins, peptides, and lipids that are used in the form of solutions, gels, emulsions, and colloids. Perspectives into the future of macromolecular oral lubricants in the treatment of xerostomia are also provided.

Aqueous Dispersion of Aramid Nanofibers Achieved by Using Tannic Acid for Ultrahigh Strength Films.

Polymer nanofibers have established a robust foundation and possess immense potential in various emerging fields such as sensors and biotechnology. In this study, aqueous dispersions of aramid nanofibers (ANFs) were successfully prepared by using tannic acid (TA). Morphological analysis revealed that TA effectively prevented self-aggregation of ANFs, and preserved the nanofiber structure during TA-assisted solvent exchange. Subsequently, the ANF and TA/ANF films were fabricated using casting and vacuum-assisted filtration techniques. Notably, the tensile strength of the casting TA/ANF film reached 393.8 MPa, exhibiting a remarkable improvement of 41.3% compared to that of the pure ANF film. These exceptional mechanical properties can be attributed to the well-dispersed nanostructures, hydrogen-bonding interactions, zigzag structures, and fiber-bridging effects. Furthermore, the TA/ANF film demonstrated superior ultraviolet (UV) shielding capabilities, visible transparency properties, and excellent resistance to chemical reagents. The above-mentioned interesting findings demonstrate its potential as a nanofiber-reinforced material for poly(vinyl alcohol) (PVA) composites.

Properties of APTES-Modified CNC Films.

Sulfated cellulose nanocrystals' (CNCs') facile aqueous dispersibility enables producing films, fibers, and other materials using only water as a solvent but prevents using sulfated CNCs in applications that require water immersion. We report that modifying CNCs with 3-aminopropyl-triethoxysilane (APTES) via a simple, single-pot reaction scheme dramatically improves the hydrolytic stability of CNC films. The effects of APTES modification on CNCs' properties were studied using attenuated total reflectance Fourier transform infrared spectroscopy, atomic force and optical microscopy, thermogravimetric analysis, dynamic light scattering, and ultimate analysis. Substituting a mere 12.6% of the CNCs' available hydroxyl groups with APTES dramatically increased the hydrolytic stability of shear cast films while only having minor impacts on their mechanical properties. In addition, quartz crystal microbalance with dissipation monitoring (QCMD) and multiparametric surface plasmon resonance (MP-SPR) studies showed that the CNC-APTES films also had a greater irreversible binding with carbofuran, a pesticide and emerging contaminant. These results highlight that APTES modification is a promising method for increasing the utility of sulfated CNCs in sensors, adsorbents, and other applications requiring water immersion.

Amino acid driven synthesis of gold nanoparticles: A comparative study on their biocompatibility

Gold nanoparticles (GNps) were successfully synthesized via 17 different l-Amino acids (AA-GNps) as reducing agents, in a one-pot reaction. Comparative characterization of AA-GNps revealed variations in their size, morphology, and structure, highly dependent on the nature of the employed amino acid. Aromatic amino acids proved to be fast-reducing agents directing the formation of GNps. Hydroxylic and basic amino acids were the slowest reducing agents for the synthesis of GNps. Aliphatic amino acids produced GNps of similar behavior, except Isoleucine which led to the formation of hollow nanospheres. GNps formulated by aspartic acid and asparagine have comparable properties to citrate-synthesized GNps, which is the golden standard in plasmonic nanoparticles. A new protocol was established for the determination of gold content in GNps’ colloidal solutions via a simple and cost-effective standard curve method employing UV–Vis spectroscopy. Most AA-GNps are colloidally stable, in both aqueous dispersion and simulated body fluid, posing as excellent candidates for in vitro experimentation. Comparative screening for their biocompatibility demonstrated the non-hemolytic and cytocompatible profile of most AA-GNps, via different in vitro assay protocols, performed on blood samples and the healthy cell line of Human Embryonic Kidney cells (HEK-293).

Light‐induced Delivery of Charged Species using Ion‐selective Core–Shell Nanoparticles

AbstractControlled release systems have gained considerable attention owing to their potential to deliver molecules, including ions and drugs, in a customized manner. We present a light‐induced ion‐transfer platform consisting of a dispersion of nanoparticles (NPs, ~300 nm) with the conductive polymer poly(3‐octylthiophene‐2,5‐diyl) (POT) in the core and a potassium (K+)‐selective membrane in the shell. Owing to the photoactive nature of POT, POT NPs can be used for a dual purpose: as a host for positively charged species and as an actuator to trigger the subsequent release. POT0 and doped POT+ coexist in the core, allowing K+ encapsulation in the shell. As POT0 is photo‐oxidized to POT+, K+ is released to the (aqueous) dispersion phase to preserve the neutrality of the NPs. This process is reversible and can be simultaneously assessed using the native fluorescence of POT0 and via potentiometric measurements. The NP structure and its mechanism of action were thoroughly studied with a series of control experiments and complementary techniques. Understanding the NP and its surrounding interactions will pave the way for other nanostructured systems, facilitating sophisticated applications. The delivery of ionic drugs and interference/pollutant catching for advanced sensing/restoration will be considered in future research.

Light-induced Delivery of Charged Species using Ion-selective Core-Shell Nanoparticles.

Controlled release systems have gained considerable attention owing to their potential to deliver molecules, including ions and drugs, in a customized manner. We present a light-induced ion-transfer platform consisting of a dispersion of nanoparticles (NPs, ~300 nm) with the conductive polymer poly(3-octylthiophene-2,5-diyl) (POT) in the core and a potassium (K+)-selective membrane in the shell. Owing to the photoactive nature of POT, POT NPs can be used for a dual purpose: as a host for positively charged species and as an actuator to trigger the subsequent release. POT0 and doped POT+ coexist in the core, allowing K+ encapsulation in the shell. As POT0 is photo-oxidized to POT+, K+ is released to the (aqueous) dispersion phase to preserve the neutrality of the NPs. This process is reversible and can be simultaneously assessed using the native fluorescence of POT0 and via potentiometric measurements. The NP structure and its mechanism of action were thoroughly studied with a series of control experiments and complementary techniques. Understanding the NP and its surrounding interactions will pave the way for other nanostructured systems, facilitating sophisticated applications. The delivery of ionic drugs and interference/pollutant catching for advanced sensing/restoration will be considered in future research.

Aqueous inks for ecofriendly processing of organic solar cells: Investigation of morphological changes

Aqueous dispersions of organic semiconducting nanoparticles (NPs) are particularly attractive as inks for the environmentally friendly preparation of organic solar cells. The internal morphology of the NPs, which depends on their elaboration process, is a key parameter, which has a significant influence on the final morphology of the active layer and therefore its effectiveness. In the present study, core-shell (PF2:PC71BM) NPs were prepared by miniemulsion. Their internal morphology including the composition of the two phases was characterized by scanning transmission X-ray microscopy (STXM) showing a core composed of 77% PC71BM and a shell composed of 75% PF2. It was found that thermal annealing promotes PC71BM diffusion from the core to the shell, increasing its proportion in the shell from 25% to 42%. This annealing, when applied after NPs deposition by spincoating, allows partial coalescence of the NPs, reducing the roughness of the active layer, and increases electron mobility, thus demonstrating the formation of PC71BM percolation paths for electron transport. A PCE of 1.6% could thus be obtained after 10 min of thermal annealing at 100°C. At higher temperature, Grazing-Incidence Wide-Angle X-Ray Scattering (GIWAXS) analyses demonstrate the modification of the PF2 structuration from randomly oriented lamella after deposition to edge-on orientation after annealing, leading to an unfavorable decrease of the hole mobility in the direction perpendicular to the substrate, while increasing the hole mobility in the substrate plane. This study demonstrates the need to systematically characterize the internal morphology of NPs in order to rationalize the morphology of the active layer and optimize its properties.

Enhancing anticorrosive performance of epoxy-based coatings using magnetite/graphene hybrids modified with ionic liquids

Hybrid materials based on magnetite (Fe3O4) and graphene nanoplatelets (GNP) were prepared by the in situ co-precipitation synthesis of Fe3O4 in the presence of GNP aqueous dispersion. Alkyl-phosphonium–based ionic liquids bearing bromide (IL102) and diethyl phosphate (IL169) as the counter-anions were used for the first time to improve the dispersion of GNP. The successful preparation of the hybrids and the final incorporation of the ILs in the hybrids were confirmed by thermogravimetric analysis (TGA) and Fourier transform infrared (FTIR) spectroscopy. The exfoliation of the GNP sheets and the incorporation of Fe3O4 particles on the GNP surface were confirmed by transmission electron microscopy. The effect of different hybrids on the corrosion resistance of the epoxy coatings was evaluated in saline medium using by electrochemical impedance spectroscopy (EIS). Hybrids prepared by the in situ synthesis of magnetite (Mag@GNP) promoted better corrosion resistance than pure magnetite or those hybrids introduced into the epoxy coatings by physical blends, due to better dispersion of the former fillers into the epoxy matrix. The best anti-corrosion response was achieved using 5 % of Mag@GNP 102 due to the better filler dispersion and higher amount of incorporated ionic liquid in the system, which can act as inhibition agent for the corrosion process.

Reversible Stacking and Delamination-Regulation of MXene via Controlled Freezing.

MXene's configuration, whether it is aggregated or dispersed in a monolayer, determines the specific application areas and even greatly influences the intrinsic properties of MXene. However, how to desirably control MXene's configuration is challenging. Here, a simple, additive-free, chemical reaction-free, and scalable strategy to optionally and reversibly regulate MXene's ordered stacking and delamination of MXene aggregates (AM) is reported. Just by controlled freezing of MXene aqueous dispersions, the aggregation percentage, delamination percentage, and interlayer spacing of AM can be finely tuned. Experimental results reveal that the freezing-induced aggregation and delamination effects can be explained by the squeezing action of growing ice grains on the MXene excluded/concentrated between ice grains and the expanding action caused by the ice formation between AM lamellae, respectively. The dominance between them depends on the freezing parameter-influenced ice nucleation sites, numbers, and ice grain sizes. This work not only contributes to the preparation, storage, and practical applications of MXene, but also opens a new and green avenue for controlling materials' assembly structures.

A novel method for the synthesis of solvent‐free and high‐solid‐content waterborne polyurethanes by introducing a small amount of polyethylene glycol

AbstractIn the study, the synthesis process involved the reaction of dimethylolbutyric acid and polytetramethylene ether glycol 1000 (PTMG1000) with hexamethylene diisocyanate (H12MDI), taking advantage of their mutual dissolution at high temperatures. The chain‐extension reaction with 1,4‐butanediol (BDO) was successfully conducted without the use of organic solvents. The emulsification reaction was carried out using the polyurethane prepolymer at 60% solids content, along with aqueous dispersions of polyethylene glycol (PEG) with varying molecular weights and amounts as interfacially active agents. Fourier transform infrared spectroscopy analysis suggested potential hydrogen bonding interactions between the PEG molecular chain and the polyurethane chain. Rheometer analysis demonstrated a significant reduction in viscosity with the addition of 1–5 wt.% PEG, accompanied by an increase in average particle size. This phenomenon was attributed to the formation of a hydrophilic lubrication layer of PEG around the water‐based polyurethane (WPU) microcells. Among them, WPU films containing 4 wt.% PEG4000 not only exhibited soft properties with a mechanical elongation rate exceeding 2000% but also showed excellent storage stability. The addition of long‐chain PEG facilitated the formation of a lubrication layer between the microcells, contributing to spatial stabilization and reducing particle aggregation at high solids content. It is noteworthy that this solvent‐free process, without any organic solvents, together with the adjusted PEG content, successfully synthesized waterborne polyurethanes with low viscosity and high solids content. This provides a new sustainable and environmentally friendly method for the future production of waterborne polyurethanes.

Novel Dry Hyaluronic Acid-Vancomycin Complex Powder for Inhalation, Useful in Pulmonary Infections Associated with Cystic Fibrosis.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavorable drug properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with a high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use in inhalable formulations. A particulate-solid HA-VAN25 complex was obtained by spray drying from an aqueous dispersion. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern was observed by X-ray. The powder density, geometric size and morphology showed the suitable aerosolization and aerodynamic performance of the powder, indicating its capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 h. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

Employing phosphorescent carbon dots@silica for glutathione sensing with low background interference

Glutathione (GSH) has important physiological functions and has been implicated in several diseases. It is therefore of great physiological importance and clinical value to develop simple and efficient methods for measuring GSH levels. However, common used luminescent materials with short lifetimes inevitably generated background signal from the biological samples during light excitation. In this work, a GSH sensing method with ultralow background interference was developed using phosphorescent carbon dots (CDs). Introducing heteroatom and carbonyl group effectively activated the triplet state of phosphorescent CDs. Meanwhile, immobilization of CDs in SiO2 (CDs@SiO2) realized long-lived phosphorescent emission (lifetime of 1.54 s) in aqueous dispersion. Manganese dioxide (MnO2) quenched the phosphorescence of CDs@SiO2 via inner filter effect and triplet energy transfer, yet the phosphorescence was restored when GSH was present. The phosphorescence was recorded when the excitation source was turned off, which successfully eliminated the background fluorescence of biological samples. The work presented here will promote the fabrication of bioprobes with low background.

Noncovalent Functionalization of Graphene Nanoplatelets and Their Applications in Supercapacitors.

We demonstrate a simple noncovalent functionalization technique, which involves graphite exfoliation and subsequent coating of the resulting graphene nanoplatelets (GNPs) with trimellitic anhydride (TMA), using a thermomechanical exfoliation process. TMA adsorbs on the surface of the GNPs, resulting in a reduction of the specific surface area to 312 ± 9 m2/g compared to 410 ± 12 m2/g for the unmodified GNPs. Detailed imaging, thermogravimetric, and X-ray diffraction analysis showed that the modified GNPs (TMA-GNPs) maintain similar structure to the unmodified GNPs. The presence of functional groups, confirmed by X-ray photoelectron spectroscopy analysis, caused an increase in the surface energy from 45.6 mJ/m2 for the GNPs to 57.9 mJ/m2 for TMA-GNPs. The resulting coated TMA-GNPs form stable dispersions in water while maintaining their inherent conductive properties, thus enabling applications, such as the manufacture of conductive films and supercapacitors. As a proof-of-concept, electrodes for supercapacitors are prepared from concentrated aqueous dispersions of the functionalized GNPs. Electrochemical characterization of the supercapacitors using electrochemical impedance spectroscopy, cyclic voltammetry and galvanostatic charge/discharge tests showed a specific capacitance of 22.2 F/cm3 at a scan rate of 1 mV/s from cyclic voltammetry and 17.3 F/cm3 at a current density of 1 A/g from galvanostatic charge/discharge tests, with a 90% capacitance retention after 10,000 cycles.

Biomimetic Dehydrogenation of Non-Conventional Lignin Monomers on Cellulose Ferulate Interfaces.

Cellulose ferulate, synthesized by Mitsunobu reaction, is shaped into thin films and also used as an aqueous dispersion to perform artificial lignin polymerization on anchor groups. This biomimetic approach is carried out in a Quartz crystal microbalance with a dissipation monitoring (QCM-D) device to enable online monitoring of the dehydrogenation, applying H2O2 and adsorbed horseradish peroxidase (HRP). The systematic use of phenylpropanoids with different oxidation states, i.e., ferulic acid, coniferyl aldehyde, coniferyl alcohol, and eugenol allowed to conclude structure-property relationships. Both the deposited material, as well as the surface roughness increased with the hydrophobicity of the monomers. Beyond surface characterizations, py-GC-MS, HSQC NMR spectroscopy and Size exclusion chromatography (SEC) measurements revealed the linkage types β-β, β-5, 5-5, and β-O-4, as well as the oligomeric character of the dehydrogenation products. All samples possessed an antibacterial activity against B. subtilis and can be used in the field of antimicrobialbiomaterials.

Preliminary Assessment of Tara Gum as a Wall Material: Physicochemical, Structural, Thermal, and Rheological Analyses of Different Drying Methods.

Tara gum, a natural biopolymer extracted from Caesalpinia spinosa seeds, was investigated in this study. Wall materials were produced using spray drying, forced convection, and vacuum oven drying. In addition, a commercial sample obtained through mechanical methods and direct milling was used as a reference. The gums exhibited low moisture content (8.63% to 12.55%), water activity (0.37 to 0.41), bulk density (0.43 to 0.76 g/mL), and hygroscopicity (10.51% to 11.42%). This allows adequate physical and microbiological stability during storage. Polydisperse particles were obtained, ranging in size from 3.46 µm to 139.60 µm. Fourier transform infrared spectroscopy characterisation confirmed the polysaccharide nature of tara gum, primarily composed of galactomannans. Among the drying methods, spray drying produced the gum with the best physicochemical characteristics, including higher lightness, moderate stability, smaller particle size, and high glass transition temperature (141.69 °C). Regarding rheological properties, it demonstrated a non-Newtonian pseudoplastic behaviour that the power law could accurately describe. The apparent viscosity of the aqueous dispersions of the gum decreased with increasing temperature. In summary, the results establish the potential of tara gum as a wall material applicable in the food and pharmaceutical industries.

Covalently grafting multihydroxy hyperbranched polymer on the surface of Ti3C2Tx MXene with remarkably enhanced colloidal stability and functionality for photothermal therapy

While MXenes have garnered acknowledgment for their remarkable photothermal properties, their practical usage has been hindered by their limited stability in aqueous mediums and vulnerability to external environmental factors. To address this issue, herein, we propose a simple and feasible method to enhance Ti3C2Tx MXene by utilizing its Ti-OH groups to directly initiate the ring-opening polymerization of glycidol. This process leads to covalently grafting multihydroxy hyperbranched polyglycerol (HPG) on the surface of MXene. The resulting Ti3C2-HPG nanohybrid demonstrates excellent aqueous dispersibility, favorable colloidal stability, and a customizable surface, thanks to the introduction of HPG. Moreover, it can withstand challenging conditions, such as extreme pH levels, high concentrations of electrolyte and bovine serum protein, and long-time storage. The abundant hydroxyl groups allow for easy modification, as demonstrated by the conjugation of rhodamine B. Preliminary in vitro and in vivo studies have unveiled that Ti3C2-HPG exhibits low cytotoxicity and exceptional photothermal performance for effectively destroying cancer cells, thus establishing it as a highly promising photothermal agent for photothermal therapy. This study thus open a new avenue for improving the stability and surface functionality of MXenes, enabling them to meet the specific requirements of practical applications.

The Chemical Reactivity of Membrane Lipids.

It is well-known that aqueous dispersions of phospholipids spontaneously assemble into bilayer structures. These structures have numerous applications across chemistry and materials science and form the fundamental structural unit of the biological membrane. The particular environment of the lipid bilayer, with a water-poor low dielectric core surrounded by a more polar and better hydrated interfacial region, gives the membrane particular biophysical and physicochemical properties and presents a unique environment for chemical reactions to occur. Many different types of molecule spanning a range of sizes, from dissolved gases through small organics to proteins, are able to interact with membranes and promote chemical changes to lipids that subsequently affect the physicochemical properties of the bilayer. This Review describes the chemical reactivity exhibited by lipids in their membrane form, with an emphasis on conditions where the lipids are well hydrated in the form of bilayers. Key topics include the following: lytic reactions of glyceryl esters, including hydrolysis, aminolysis, and transesterification; oxidation reactions of alkenes in unsaturated fatty acids and sterols, including autoxidation and oxidation by singlet oxygen; reactivity of headgroups, particularly with reactive carbonyl species; and E/Z isomerization of alkenes. The consequences of reactivity for biological activity and biophysical properties are also discussed.

Histopathological changes in the spleen of rats exposed to N,N-dimethylhydrazine with the following protective input of Au/Ag/Fe

Colon cancer is one of the leading causes of cancer-related deaths worldwide. Despite the growing number of studies on nanoparticles of different metals, there is still a lack of reliable information about their ability to work together as a composition and their antitumor effects. It has been established that the regulation of genes encoding proteins of the Bcl-2 family changes in cancer. Bcl-2 family proteins can be a potential target in cancer diagnosis and have a prognostic value in treating cancer with chemotherapeutic drugs. The tumor microenvironment includes myeloid suppressor cells, tumor-associated neutrophils, and tumor-associated macrophages that promote cancer progression and are derived from splenic hematopoietic stem cells and progenitor cells. The work aimed to ascertain histological changes and expression of Bcl-2 family proteins in the spleen of rats with N,N-dimethylhydrazine-induced carcinogenesis followed by the protective administration of Au/Ag/Fe nanometal composition. The study was conducted on 72 outbred white male rats. Colon adenocarcinoma was modelled by N,N-dimethylhydrazine hydrochloride administration for 30 weeks. Animals received an aqueous dispersion of Au/Ag/Fe nanoparticles intragastrically once a day for 21 days at a dose of 0.842 mg Ag/0.0526 mg Fe/1.625 μg Au per 1 kg of rat body weight. Paraffin sections of the spleen were stained with hematoxylin and eosin. For immunohistochemical analysis, sections were stained with rabbit monoclonal antibodies to Bcl-2. Under conditions of 30-week exposure to N,N-dimethylhydrazine hydrochloride, blood circulation disorders, stasis, thrombosis, reduction in the size of white pulp lymphatic nodules and loss of their zonation were histologically proved in the rat's spleen. The development of sclerotic processes in the organ was noted. It was indicated that using metal nanoparticles under N,N-dimethylhydrazine hydrochloride-induced colon carcinogenesis leads to less evidenced morphological manifestations of structural changes in the spleen. Immunohistochemically, the expression of Bcl-2 protein in the white pulp of the spleen of animals subjected to correction was lower than in animals without the corrective effect of the composition of nanoparticle metals. Administration of the Au/Ag/Fe metal nanoparticle composition to intact white rats does not cause pathological changes in the spleen morphology. The structural components of the red and white pulp match the typical histological structure of the organ.

Nanoparticle‐Based Cryogels from Colloidal Aqueous Dispersion: Synthesis, Properties and Applications

AbstractCryogels have morphological features that make them interesting for several applications such as catalysis, sensing or tissue engineering. Their interconnected network and open porous structure, build up by primary particles (such as inorganic nanocrystals or polymers), provide these materials with unique physical properties and high specific surface areas. While the library of cryogels is endless, widely used in the polymer chemistry field, in this review we will summarize the structure and properties, applications and challenges of inorganic nanocrystal‐based cryogels obtained by freezing and freeze‐drying an aqueous nanoparticle colloid. This fast, easy and versatile gelation method will be outlined, along with the corresponding macro‐, micro‐ and nano‐structures and gel morphologies that can be obtained, for example, by changing the freezing temperature or by using one nanoparticle system or nanoparticle mixtures. Their applications towards electrocatalysis, photocatalysis and photoelectrochemical sensing will be highlighted, as well as the challenges and prospects of these materials.