Antistatic Properties Research Articles

Flexible and lightweight carbon fiber/silicone resin composites with the “soft-rigid” structural interface for thermostable and antistatic applications

To avoid a large difference in modulus between carbon fiber (CF) and silicone resin (SR) and unstable thermal properties, the “soft-rigid” structural interface is constructed by coating polydopamine-polyethyleneimine@octaphenyl-silsesquioxane (PDA-PEI@octaphenyl-POSS) on the fiber surface. The tensile strength of the CF-AE@3P/SR composite was 24.35 % higher than that of the unmodified CF/SR. The mechanism of mechanical enhancement revealed that the rigid layer with nanoparticles effectively deflected the crack and prolonged the path, and the hydrogen bonds and van der Waals forces helped disperse the stress concentration at the interface. The defects in the soft–rigid structural interface were reduced, and the decomposition of the fibers and composites was effectively inhibited, thereby increasing the heat transmission in the composites. After heating for 20 s on the heating plate at 200 °C, the surface temperature of the CF-AE@3P/SR composite was 155.4 °C, which is higher than that of the unmodified CF/SR (131.4 °C). Therefore, the thermal stability of the CF-AE@3P/SR composites was significantly improved compared to that of unmodified CF/SR after holding at 350 °C for 3 h. Surface resistance analysis showed that the soft–rigid modification maintained the antistatic properties of the composites at room and high temperatures. It was also found that the CF-AE@P/SR composites exhibited good flexibility, lightweight, and hardness for application in sealing and electronic components. This work provides ideas for forming a seamless transition and effective bonding between high-modulus carbon fibers and a low-modulus elastomer matrix, increasing the thermal stability and mechanical properties, and maintaining the flexibility, stiffness, lightweight, and antistatic properties of composites at high temperatures

Flexible and antistatic carbon fiber/silicone rubber composite coating with improved thermal stability, mechanical and wave-transmission properties

The properties of the interface have a significant impact on the application of silicone rubber (SR) composite coating fillers with carbon fiber (CF). The one-step growth of silica nanoparticles on the fiber surface was investigated in terms of the mechanical, electrical, and thermal properties of the CF/SR composite coatings. The results showed that the tensile strength and elongation of the composite with modified fibers were 7.13 ± 0.44 MPa and 690.40 ± 37.04 %, which were 20.44 % and 23.22 % higher than those with unmodified CFs, respectively. The improvement in interfacial adhesion by silica modification effectively disperses stress and avoids stress concentration. Additionally, the introduction of the low-dielectric material SiO2 and the reduction of the interfacial polarization enhanced the wave-transmission properties and weakened the electromagnetic wave-shielding properties of the composites. Meanwhile, the silica modification maintained the antistatic properties of the coatings at room and high temperatures, as well as before and after bending. The weight loss of the composites with modified fibers was lower than that of the composites with unmodified fibers, while the thermal conductivity was higher because of the stable structure of the Si-O-Si bonds and interfacial adhesion. This work provides a simple way to enhance the thermal resistance, thermal conductivity, mechanical and wave-transmission properties, and preserve the antistatic properties as well as the flexibility of CF/SR composite coatings.

Biopolymer-containing formulations to render acrylic fabrics fire resistant and anti-static

Although widely used in textile applications, acrylic fabric (AF) suffers from being hydrophobic, with a surface that has a high tendency to catch fire and create electrostatic charge. Many methods have been adopted to improve the performance attributes of AF; however, theyare either polluting or not durable against repeated washing. Herein, a synergy of phytic acid (PA) and a protein biopolymer, namely keratin or sericin, was adopted to boost the resistance to flame, ultraviolet rays, and electrostatic charges, as well as enhance the hydrophilicity of AF. An efficient flame retardant (FR) was synthesized by reacting calculated amounts of PA and pentaerythritol (PE) to form hexa-pentaerythritolphytate ester (HPP), which in turn reacted with a proteinic biopolymer in the presence or absence of a crosslinking agent to produce a multifunctional FR formulation. The prepared formulation was utilized as a multifunctional textile auxiliary for improving the resistance of alkali-hydrolyzed AF to flame and UV rays and for enhancing its hydrophilic and anti-static properties. The chemical structure of the synthesized functional FR was investigated using FTIR and by determining its phosphorus, nitrogen, and carboxylic contents. The mechanism of reaction between the synthesized FR and the hydrolyzed fabric was proposed. The discrepancy between the topographies of the treated and untreated fabrics was monitored using scanning electron microscopy. The results revealed that the treated AF exhibited a durable and superior resistance to flame, which was not adversely affected by washing up to 20 times. The anti-static property and wettability of the treated fabrics were highly improved, whereas their resistance to the deteriorative action of UV rays was enhanced to an almost an adequate level according to AS/NZS 4399:1996. The proposed process is an additive method for improving some performance and comfort attributes of AF without causing a severe loss in the fabric’s strength.

Preparation of Antistatic Polyester Fiber via Layer-by-Layer Self-Assembly

Polyester fibers tend to generate static electricity during the weaving and application processes, posing a threat to their production. Enhancing the water absorbency and electrical conductivity of polyester fibers themselves is an effective approach to improving their antistatic properties. In this study, multifunctional chitosan (CS), sodium phytate (SP), and Cu2+ were loaded on polyester fibers through layer-by-layer (LBL) self-assembly. The antistatic and water absorption capability of the modified polyester fibers was investigated by designing different process parameters combined with a surface resistance test and water contact angle tests. The antistatic property test results confirmed the positive effect of CS and Cu2+ on discharging electrostatic charge. Within a definite scope, with the increase in the number of assembly layers, assembly duration, and the concentration of the assembly substances, the wettability of the modified polyester fibers became more favorable and the antistatic effect became more remarkable.

Synthesis of Newly Ester Type Gemini Cationic Surfactants: Surface Properties, Fabric Softness and Antibacterial Properties

AbstractFour ester cationic Gemini surfactants (EDQ‐n, n represents the carbon number in the raw fatty acid of 12, 14, 16 and 18) were synthesized from fatty acid, N, N‐dimethylethanolamine and 1, 4‐dibromobutane by two‐step reaction of esterification and quaternization. Their surface activities at air/water interface were investigated. The application performance such as water solubility, antistatic property, fabric softness, fabric whiteness, biodegradability, and antibacterial activities were tested and compared with traditional quaternary ammonium salt. The results showed that the γcmc increases with increasing the hydrophobic chain length and EDQ‐12 presented the highest surface activity. The diffusion coefficients calculated from the Ward‐Tordai equation indicates the adsorption process is a mixed‐diffusion kinetic adsorption mechanism. The water solubility of EDQ‐n is higher than dioctadecyl dimethyl ammonium chloride (D1821) and ester quaternary ammonium salt (Esterquats). The fabric softness and whiteness properties of EDQ‐16 and EDQ‐18 are similar to D1821 and Esterquats, which can significantly reduce the cotton fabric softness and have no significant difference in whiteness retention. EDQ‐n demonstrated more readily biodegradation(>90 %) than D1821(0 %) after seven days. In addition, EDQ‐12 and EDQ‐14 show excellent antibacterial activities against Staphylococcus aureus and Escherichia coli in comparison with conventional bacteriostatic agent didecyl dimethyl ammonium chloride (DDAC).

Research of the anti-static and corrosion resistance of S-ZnO/m-SWCNTs/ FC composite coating

Abstract In order to solve the hazards caused by corrosion and charge accumulation in aircraft, electronic equipment, oil and gas pipelines, the corrosion resistance and anti-static performance of coatings need to be noted. In this study, monodisperse single-walled carbon nanotubes functional slurry (m-SWCNTs) was obtained by the combination of high-energy ultrasonic dispersion and non-covalent amphiphilic dispersant (PVP). In this way, the uniform dispersion of low-content m-SWCNTs in fluorocarbon composite coatings was achieved, and the micronano structured surface of the fluorocarbon composite coating was constructed by using the modified-ZnO in order to achieve superhydrophobicity. The results showed that the corrosion resistance of the fluorocarbon composite coating was further improved and the antistatic property of the composite coating met the use requirements, which was achieved through the synergistic effect of the m-SWCNTs network and the modified-ZnO. The resistivity of S-ZnO/m-SWCNTs/FC coating is 3.15 Ωm, acting as anti-static coating to reduce safety hazards, its corrosion current is 9.66×10−8 A/cm2, which is lower than bare steel by 3 orders of magnitude. Meanwhile, the composite coating owns the self-cleaning, superhydrophobic and organic solvent affinity, acting as oil-water separation coating. This research provides a new idea for the fabrication of multifunctional coating, elucidating the significant potential of its applications.

Long-lasting antistatic hydrophilic polyethylene terephthalate fabric using greener reagents

AbstractPolyethylene terephthalate (PET) is the most common synthetic polymer used in the textile sector by virtue of its unique superior performance attributes. However, the comfort characteristics of PET fabrics, such as their inadequate sweat-absorbing capability, low affinity for most dyestuff classes, and susceptibility to the accumulation of electrostatic charge, make them unfavorable compared to natural fibers. Rendering PET fabrics with hydrophilic and antistatic properties is difficult due to the lack of reactive functional groups. Herein, a long-lasting eco-friendly strategy to impart some desirable properties to PET fabrics was developed. The PET fabric was saponified in an aqueous caustic soda solution, followed by treatment with an amino acid, namely lysine, aspartic acid, serine, tyrosine, or cysteine, as a coupling agent, and eventually, the fabric was finished with the protein biopolymer gelatin using the pad-dry-cure method. The effects of treatment of PET fabric with the aforementioned reagents on its surface hydrophilicity, roughness, antistatic, thermal stability, ultraviolet protection, air permeability, yellowness, bending stiffness, and tensile properties were monitored. The discrepancy between the chemical structures of the untreated and finished fabrics was determined using Fourier transform infrared spectroscopy as well as by determining the carboxylic and nitrogen contents. The morphological and crystal structures of the treated fabrics were examined using scanning electron microscopy and X-ray diffraction pattern, respectively. The results indicate that a maximum add-on was obtained upon treatment of the saponified PET fabrics with 0.5 M lysine followed by 7.5% (on the weight of the fiber) gelatin using the pad-dry-cure method.The finished PET fabrics exhibited improved hydrophilic and antistatic properties with adequate protection against UV rays.Ingeneral, treatment of PET fabrics with gelatin, using a bi-functional amino acid as a coupling agent, is an effective and durable method to improve some performance and comfort features of PET fabric without having a remarkable negative effect on the fabric’s mechanical properties.

Application Properties of Gemini Quaternary Ammonium Salt with Quadra‐cationic Sites and Sodium Fatty Alcohol Polyoxyethylene Ether Carboxylate Mixed Systems

AbstractThe application properties such as foam property, electrolyte tolerance, antibacterial activity and antistatic performance of the mixed systems of a novel Gemini quaternary ammonium salt with quadra‐cationic sites (TC‐GS) and sodium fatty alcohol polyoxyethylene ether carboxylate (AE9CNa) at various molar fraction of TC‐GS (αTC‐GS), were investigated systematically. Results show that TC‐GS/AE9CNa mixed systems with different ratios form a homogeneous and transparent solution, which exhibits excellent foam stability and antibacterial activity. The foam volume of the mixed system remains nearly constant from 400 s to 1000 s, and even when TC‐GS is 10 mg/L in the mixed systems, the antibacterial rates against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) for 2 min. are all exceeded 99 %. The mixed systems of TC‐GS/AE9CNa at various αTC‐GS also demonstrate the superior electrolyte tolerance, their maximum tolerance of NaCl, CaCl2 and MgCl2 is severally beyond 270 g/L, 180 g/L and 180 g/L. In addition, both TC‐GS solution and the mixed systems have good antistatic properties, which can reduce the surface resistance of polyester fabric to ≤1010 Ω.

Direct Ink Writing of Highly Conductive and Strongly Adhesive PEDOT:PSS-EP Coatings for Antistatic Applications

As the information age progresses, the electronics industry is evolving towards smaller and more sophisticated products. However, electrostatic potentials easily penetrate these components, causing damage. This underscores the urgent need for materials with superior antistatic properties to safeguard electronic devices from such damage. Antistatic coatings typically rely on polymers as the primary material, enhanced with conductive fillers and additives to improve performance. Despite significant progress, these coatings still face challenges related to advanced processing technologies and the integration of electrical and mechanical properties. Among various conductive fillers, the conducting polymer PEDOT:PSS stands out for its exceptional conductivity, environmental stability, and long cycle life. Additionally, epoxy resin (EP) is widely utilized in polymer coatings due to its strong adhesion to diverse substrates during curing. Here, we develop highly conductive and strongly adhesive PEDOT:PSS inks by combining PEDOT:PSS with EP using a composite engineering approach. These inks are used to fabricate PEDOT:PSS coatings by direct ink writing (DIW). We systematically evaluate the DIW of PEDOT:PSS-EP coatings, which show high electrical conductivity (ranging from 0.59 ± 0.07 to 41.50 ± 3.26 S cm−1), strong adhesion (ranging from 15.84 ± 2.18 to 99.3 ± 9.06 kPa), and robust mechanical strength (8 MPa). Additionally, we examine the surface morphology, wettability, and hardness of the coatings with varying PEDOT:PSS content. The resultant coatings demonstrate significant potential for applications in antistatic protection, electromagnetic shielding, and other flexible electronic technologies.

A benign synergism of O2 plasma and protein biopolymer for improving some properties of polyester fabrics

Polyester (PET)is the most widely used fiber in the textile and clothing fields by virtue of its cheapness, strength, crease-resistance, stain-resistance, and ease of drying. However, PET fabric lacks the antistatic properties, hydrophilicity, and affinity for most classes of dyes. Here, freshly extracted keratin from poultry feathers and sericin from silkworm cocoons were used for the first time to make oxygen plasma-treated PET fabric surfaces hydrophilic, antistatic, and dyeable with cationic dye. Adopting the pad-dry-cure technique, oxygen plasma-activated PET fabrics were successfully coated with a layer of sericin or keratin as indicated by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The effects of plasma irradiation time as well as curing temperature and duration on the properties of the treated fabric were monitored. The results of this study revealed that the plasma/biopolymer-treated fabrics have become dyeable with the cationic dye C.I. Basic Violet 16. The effect of treatment of PET fabric on some of its physical and mechanical properties, such as wettability, antistatic properties, yellowness index, air permeability, water vapor permeability, ultraviolet protection factor, burst strength, and bending stiffness, was monitored. The durability of the finished sample against repeated washing in terms of the fabric resistivity was examined. The alterations in the chemical, crystal, and morphological structures of the treated fabric were assessed using Fourier transform infrared spectroscopy, XPS, X-ray diffraction, and SEM.

Polysilane–Barium Titanate Polymeric Composite Obtained through Ultrasonication

This work describes the synthesis of a polysilane (PSH)–barium titanate (BT) ferroelectric polymer composite that keeps stable in the presence of ultraviolet light (UV). To evaluate the stability in the presence of UV radiation and the mechanism of interaction between the PSH matrix and BT, FTIR measurements were carried out. The UV/VIS absorption measurement reveals that PSH absorbs strongly in the ultraviolet range, while the composite behaves similarly to BT. Although PSH is a semiconductor, the dielectric spectrometry analysis determined that BT is a ferroelectric material due to its high dielectric constant and low dielectric losses. In contrast to the polymer matrix, the composite polymer has a greater dielectric constant and a lower loss permittivity. PSH is a semiconductor, as indicated by its electrical conductivity of 10−5 S/cm; nevertheless, the UV-irradiated polymer has antistatic properties (10−8 S/cm). Irradiated or not, the polymer composite is a semiconductor, with conductivity of 10−6 S/cm, significantly lower than that of PSH. The interaction with electromagnetic radiation indicates electromagnetic shielding behavior for both BT (highest absorption magnitude of −57 dB) and the polymer composite (maximum absorption magnitudes range from 8.4 to −15.2 dB). Based on these research results, the novel composite with specific characteristics may be used in electronic applications in UV-irradiated conditions.

A comparative study of comprehensive performances for transparent plasticized polyvinyl chloride films with different plasticizers

AbstractFor flexible polyvinyl chloride (PVC) films with excellent mechanical performances and high transparency, the demand for antistatic properties is becoming increasingly urgent in textile and electronic fields. This study compares the effects of 60 phr bis (2‐(2‐butoxyethoxy) ethyl) adipate (DBEEA) with other five equal amounts of plasticizers on the conductivity, electrical stability, transparency, and mechanical properties of plasticized PVC. The infrared spectra of plasticizers indicate that there are unique ether groups exist in DBEEA. Then the calculated solubility parameters suggest the good compatibility between DBEEA and PVC. For conductivity, the volume resistivity and surface resistivity of the PVC sample with DBEEA (PVC/DBEEA) are 107 Ω· m and 1010 Ω, respectively, which are both lower by 3–4 orders of magnitude than that of other plasticized PVC. For electrical stability, the results indicate that PVC/DBEEA placed in air still maintains lowest resistivities. Under 10, 23, and 30°C, PVC/DBEEA keeps high and stable electrical properties. The similar refractive indices of DBEEA and PVC resin prepared by suspension method indicate good transparency for PVC/DBEEA. Moreover, PVC/DBEEA still has good mechanical property.

Toward a Sustainable Approach for Durably Hydrophilic and UV Protective PET Fabric through Surface Activation and Immobilization Integrating Epigallocatechin Gallate and Citric Acid.

Enhancing the hydrophilicity and UV protective property of poly(ethylene terephthalate) (PET) fabric are two significant ways to upgrade its quality and enlarge the applicable area. Biobased finishes are greatly welcomed for the fabrication of sustainable textiles; however, their application on PET fabric is still challenging compared with the case of natural fabric. This study presents a strategy that immobilizes epigallocatechin gallate (EGCG) onto PET fabric using citric acid (CA) for durably hydrophilic and UV-proof properties with negligible color change. A controllable surface-activating method integrating alkaline and deep eutectic solvent (DES) is customized for the PET fabric to promote the reactions among PET, CA, and EGCG. The hydrophilic, antistatic, and UV protective properties of functionalized PET fabric were explored. Results show that the hydrophilicity of the PET fabric after direct EGCG treatment increases but drops sharply after first-round washing due to weak interactions. The combined alkaline/DES pretreatment increases the number of hydrophilic groups and the roughness of PET fibers. After EGCG modification, the moisture regain (MR) of PET fabric increases from 0.41 to 0.64%. The contact angle and electrostatic charge half-life (T1/2) decreases from >120 to 23°, and from >60 to 0.13 s, respectively. The MR and T1/2 are well retained after a 10-cycle washing. In addition, the UV protective factor of the PET fabric increases from 18 to 36. A very slight yellowing phenomenon occurs on the PET fabric after the treatment. In all, this research attempts to integrate a biobased finishing agent and an eco-friendly cross-linker on synthetic fiber for durable functions, which is transferrable to the sustainable fabrication of other polymeric materials such as fibers or films.

Strong and antistatic biomass adhesive for wood-based composites with electrostatic discharge protection function

Soybean protein adhesive, as an aldehyde-free biomass adhesive, has gained significant attention as an environmentally friendly material in recent years. It not only aligns with the objectives of the double carbon strategy but also contributes to the environmental protection strategy of reducing carbon emissions. And the functional modification of soybean protein adhesive and its wood composite hold great importance in expanding its application domains and meeting specialized requirements. This research focused on developing a robust, antistatic adhesive derived from soy protein as an alternative to formaldehyde-based resins, which represents a critical path in the advancement of wood-based composites that are free from formaldehyde and possess functional properties. However, ensuring the bonding strength of soy protein adhesive while developing antistatic adhesives and their wood-based composite materials is of great research value and challenge. Inspired by the organic-inorganic hybrid structure, this study aimed to prepare a strong and durable soy protein adhesive with excellent mechanical strength and multifunctionality by using a self-synthesized crosslinking agent called AP and the loaded two-dimensional MXene, which was stabilized in a dispersion of nanocellulose (CNC). The dry and wet shear strength of the resulting adhesive increased by 103.8 % and 113.8 % to 2.21 MPa and 1.24 MPa, indicating the stable crosslinking structure formed in adhesive system by the covalent bond between self-synthesized crosslinking agent AP and the carboxyl groups on proteins, as well as the hydrogen bond interactions between C-M and the proteins. Furthermore, the adhesive exhibited significant antistatic and self-extinguishing properties, with the particleboard modified by adhesive SPI/C-M/AP having a resistivity of 9.212 × 1011 Ω cm. The resistivity decreased with increasing MXene content, providing potential applications for places such as school computer rooms and factory electronic equipment rooms. This breakthrough in multifunctional biomass-based adhesives and composite materials enriches the preparation of new types of biomaterials with antistatic and flame retardant properties.

Evaluating the efficiency of functionalized zinc oxide based curing system for polychloroprene composites and analyzing its effect on curing, physical, and morphological properties for the application in specialty power transmission belts

Polychloroprene rubber (CR) is one of the most abundantly used elastomer in power transmission belt section due to its excellent oil resistance, weather resistance, antistatic and dynamic properties. However, due to the negative impact of Zinc Oxide (ZnO) used with CR rubber towards marine environment, it is necessary to minimize the use of ZnO in CR based rubber compounds. Functionalized-ZnO(F–ZnO) being emerged as a suitable replacement for regular ZnO in rubber compounding, the effect of F–ZnO on the curing, mechanical and morphological properties of polychloroprene (CR) based composites to use in power transmission belt applications are evaluated in this work. The curing properties of F–ZnO based composites were characterized using various techniques and results were reported as a comparison with the properties of conventional ZnO (C– ZnO) based CR composites. Properties of various ZnO were analyzed using X-ray Diffraction (XRD) analysis and Field-Emission Scanning Electron Microscopy (FESEM) studies. The replacement of C–ZnO with F–ZnO help to reduce 80 % of Zn content from the end products without effecting the cure time and cross-link density of the same. 5 PHR of C– ZnO from regular compound is replaced with 1 and 3 Phr of F–ZnO and its effect on power transmission belt properties were analyzed thoroughly.

Aggregation Behavior and Application Properties of Novel Glycosylamide Quaternary Ammonium Salts in Aqueous Solution.

Amidation of lactobionic acid with N,N-dimethylaminopropyltriamine was conducted to obtain N-(3'-dimethylaminopropyl)-lactamido-3-aminopropane (DDLPD), which was quaternized with bromoalkanes of different carbon chain lengths to synthesize double-stranded lactosylamide quaternary ammonium salt N-[N'[3-(lactosylamide)]propyl-N'-alkyl] propyl-N,N-dimethyl-N-alkylammonium bromide (CnDDLPB, n = 8, 10, 12, 14, 16). The surface activity and the adsorption and aggregation behaviors of the surfactants were investigated via equilibrium surface tension, dynamic light scattering, and cryo-electron microscopy measurements in an aqueous solution. The application properties of the products in terms of wettability, emulsification, foam properties, antistatic, salt resistance, and bacteriostatic properties were tested. CnDDLPB exhibited a low equilibrium surface tension of 27.82 mN/m. With an increase in the carbon chain length, the critical micellar concentration of CnDDLPBD decreased. Cryo-electron microscopy revealed that all products except C8DDLPB formed stable monolayer, multi-layer, and multi-compartmental vesicle structures in an aqueous solution. C14DDLPB has the best emulsification performance on soybean oil, with a time of 16.6 min; C14DDLPB has good wetting and spreading properties on polytetrafluoroethylene (PTFE) when the length of carbon chain is from 8 to 14, and the contact angle can be lowered to 33°~40°; CnDDLPB has low foam, which is typical of low-foaming products; C8DDLPB and C10DDLPB both show good antistatic properties. C8DDLPB and C14DDLPB have good salt resistance, and C12DDLPB has the best antimicrobial property, with the inhibition rate of 99.29% and 95.28% for E. coli and Gluconococcus aureus, respectively, at a concentration of 350 ppm.

Graphene Oxide-Enhanced and Dynamically Crosslinked Bio-Elastomer for Poly(lactic acid) Modification.

Being a bio-sourced and biodegradable polymer, polylactic acid (PLA) has been considered as one of the most promising substitutes for petroleum-based plastics. However, its wide application is greatly limited by its very poor ductility, which has driven PLA-toughening modifications to be a topic of increasing research interest in the past decade. Toughening enhancement is achieved often at the cost of a large sacrifice in strength, with the toughness-strength trade-off having remained as one of the main bottlenecks of PLA modification. In the present study, a bio-elastomeric material of epoxidized soybean oil (ESO) crosslinked with sebacic acid (SA) and enhanced by graphene oxide (GO) nanoparticles (NPs) was employed to toughen PLA with the purpose of simultaneously preserving strength and achieving additional functions. The even dispersion of GO NPs in ESO was aided by ultrasonication and guaranteed during the following ESO-SA crosslinking with GO participating in the carboxyl-epoxy reaction with both ESO and SA, resulting in a nanoparticle-enhanced and dynamically crosslinked elastomer (GESO) via a β-hydroxy ester. GESO was then melt-blended with PLA, with the interfacial reaction between ESO and PLA offering good compatibility. The blend morphology, and thermal and mechanical properties, etc., were evaluated and GESO was found to significantly toughen PLA while preserving its strength, with the GO loading optimized at ~0.67 wt%, which gave an elongation at break of ~274.5% and impact strength of ~10.2 kJ/m2, being 31 times and 2.5 times higher than pure PLA, respectively. Moreover, thanks to the presence of dynamic crosslinks and GO NPs, the PLA-GESO blends exhibited excellent shape memory effect and antistatic properties.

Robust mechanical strength and high colorfastness of amorphous photonic crystals on fabrics with durable antibacterial and anti-static properties

The technique of utilizing structural color dyeing presents a sustainable and energy-conserving approach to textile dyeing. However, the coating with structural coloration always exhibited cracks and inadequate colorfastness attributed to the presence of capillary tension. In this study, we employed a hydrophilic silane called 3-aminopropyltriethoxysilane (KH550) to chemically modify the fabric. This method endowed the fabric with reactive amino groups, thereby augmenting the interfacial bonding strength between polydopamine (PDA)@SiO2@Ag+/Ag NPs and the fabric substrate through metal coordination and covalent bonds. Additionally, by utilizing catechol complexation, we successfully loaded Ag ions onto the PDA coating of composite microspheres. These Ag ions acted as linkers during self-assembly of microspheres. The active amino groups on the surface of chemically modified cotton fabric reacted with PDA at a specific temperature, resulting in the formation of robust covalent bonds simultaneously. The resulting fabric demonstrated excellent water resistance as well as efficient antibacterial and anti-static properties, which were confirmed through various mechanical tests such as washing, folding, and rubbing experiments. This research presents an innovative approach for creating durable structural colored fabrics with multifunctional properties based on metal coordination and covalent bonds that can be effectively applied in textile printing and dyeing.

Preparation of PANI modified hollow microspheres and its application in anti-static buffer foam of OLED under-display

The polyaniline (PANI) modified hollow microspheres (HMs@PANI) was prepared by in-situ polymerization and then applied as both foaming agent and conductive fillers. The coating of PANI on the surface of hollow microspheres (HMs) was studied, and a dense conductive layer was obtained. Moreover, HMs@PANI was co-doped with acrylic acid and hydrochloric acid in order to improve the dispersion. Finally, the as-obtained HMs@PANI-CO was added into the polyacrylate matrix, then the multi-functional syntactic foam with both better anti-static property and buffer property was obtained. When the addition of HMs@PANI was 20 wt%, the surface resistivity of the foam reached 2.32×106 Ω. Furthermore, the better buffer property, lightweight, compression resistance, and thermal conductive property were also presented, which would be important in the practical application of organic light-emitting diode (OLED) under-display.

Multiple birds with one stone: A new type of PPy/Fe3O4/rGO multifunctional composite fabric for wave absorption, UV resistance, anti-static and thermal insulation

To solve the problem of electromagnetic radiation pollution, it is especially important to develop electromagnetic wave-absorbing materials with excellent performance. The preparation of composite multifunctional textile materials with excellent wave-absorbing properties is one of the research hotspots for practical personal protection applications. In this work, PPy/Fe3O4/rGO polyester/cotton composite fabrics were prepared by impregnation, chemical reduction, chemical co-precipitation and in situ polymerization. When the thickness is 0.97 mm, the minimum reflection loss (RLmin) of PPy/Fe3O4/rGO polyester/cotton composite fabric is −12.12 dB, and the effective absorption bandwidth (EAB) is 4.7 GHz, which is excellent in wave absorption. Meanwhile, the PPy/Fe3O4/rGO polyester/cotton composite fabrics have excellent UV resistance (UV transmittance ratio of UVA and UVB bands as low as 0.02 %, UPF value of 100+), antistatic properties (static voltage half-life of 0.2 s), and excellent thermal management properties (thermal conductivity as low as 0.05796 W/(m·K)), and so on. The PPy/Fe3O4/rGO polyester/cotton composite fabrics prepared in this study are suitable for a variety of application scenarios, such as individual electromagnetic protection, individual protection in extremely cold environments, and individual heating physiotherapy, which is of great reference significance for the research of wearable individual protective textile materials.