Displacement Amplitude Research Articles

Enhancing energy harvesting capability through analysis of flow-induced vibrations in double sprung circular cylinders exposed to turbulent flow: Influence of incidence angle

The current study explores the potential for energy harvesting arising from vortex-induced and wake-induced vibrations of two circular cylinders. These cylinders are elastically mounted and exposed to turbulent flow, allowing them to undergo free oscillations. Their relative orientation, determined by the incidence angle, ranges from zero to ninety degrees. To analyze this phenomenon, we employ a finite volume methodology for computational analysis to calculate the Reynolds-averaged governing equations. Additionally, we use the explicit integration method to solve the structural dynamics equations. Our numerical analysis reveals that the upstream cylinder uniquely demonstrates vortex-induced vibration, while the downstream cylinder experiences wake-induced vibration, especially at lower incidence angles. Interestingly, as the incidence angles increase, the wake-induced vibration in the downstream cylinder diminishes, and its vibration response aligns with that of the upstream cylinder. Furthermore, the power profile of the upstream cylinder corresponds to the progression of displacement amplitude. In contrast, for the downstream cylinder, at lower incidence angles, the maximum power increases with rising reduced velocity. However, at higher angles, the power behavior resembles that of the upstream cylinder. We determine that the optimal incidence angle for maximizing harvested power is θ=30°, resulting in a total root mean square (RMS) of 5.83W. This represents a substantial increase of 548% compared to the combined power of two separate cylinders. The second most effective angle is θ=15°, yielding a total RMS of 4.75W and a 375% increase, while θ=0° occupies the third position, providing a total RMS of 3.53W and a 293% increase.

Freezing Hu ram semen: influence of different penetrating cryoprotectants and egg yolk level on the post-thaw quality of sperm.

The Hu sheep is a renowned breed known for its high reproductive rate. It is in estrus all year round, and its breeding population is gradually expanding. However, the current techniques for cryopreserving semen have limited effectiveness, which hinders the continuous development of this species. The purpose of this study is to explore the effects of different penetrating cryoprotectants (CPAs) and egg yolk (EY) concentrations on the cryopreservation of Hu ram semen to determine the most effective combination. In this study, the effects of glycerol (GLY), ethylene glycol (EG), dimethylacetamide, dimethyl sulfoxide, different proportions of GLY and EG, EY on sperm quality after thawing were investigated by detecting sperm total motility (TM), progressive motility (PM), straight-line velocity, curvilinear velocity, average path velocity, amplitude of lateral head displacement, wobble movement coefficient, average motion degree, functional integrity (plasma membrane integrity, acrosome integrity) and reactive oxygen species (ROS) level. When GLY and EG were added together, compared to other concentration groups, 6% GLY significantly (p<0.05) increased TM, PM, plasma membrane integrity, and acrosome integrity of thawed sperm. Additionally, it significantly (p<0.05) decreased the ROS level of sperm. In this study, the TM, PM, and membrane integrity of the 6% EG were significantly (p<0.05) higher than those of the control, 1% GLY+5% EG and 6% GLY+6% EG groups. Compared to other concentration groups, 20% EY significantly (p<0.05) improved the TM, PM, and plasma membrane integrity of thawed sperm. However, the integrity of the acrosome increased with the higher concentration of EY. In conclusion, the post-thawed Hu ram semen diluted with a diluent containing 6% GLY and 20% EY exhibited higher quality compared to the other groups.

Characteristics and energy flux distributions of decayless transverse oscillations depending on coronal regions

It has been proposed that the slope (delta ) of the power-law distribution between the energy flux and oscillation frequency could determine whether high-frequency transverse oscillations make a dominant contribution to the heating ($ A meta-analysis of decayless transverse oscillations revealed that high-frequency oscillations potentially play a key role in heating the solar corona. We aim to investigate whether or not (and, if so, how) the distributions of the energy flux contained in transverse oscillations, and their slopes, depend on the coronal region in which the oscillation occurs. We analysed transverse oscillations from 41 quiet Sun (QS) loops and 22 active region (AR) loops observed by Solar Orbiter/Extreme Ultraviolet Imager (EUI) hrieuv . We estimated the energy flux and energy using analysed oscillation parameters and loop properties, such as periods, displacement amplitudes, loop lengths, and minor radii of the loops. We find that about 71&lt;!PCT!&gt; of QS loops and 86 &lt;!PCT!&gt; of AR loops show decayless oscillations, and that the amplitude does not change depending on different regions, but the difference in the period is more pronounced. Although the power law slope ($ in AR is steeper than that ($ in QS, both of them are significantly less than the critical slope of 1. Our statistical study demonstrates that high-frequency transverse oscillations can heat the QS. For ARs, the total energy flux is insufficient unless yet-unobserved oscillations with frequencies of up to 0.17 Hz are present. Future EUI campaigns will be planned to confirm whether a corresponding high-frequency oscillation exists.

Wind-induced vibration energy harvesters under base excitation: Analytical and numerical analysis

In this paper, analytical analysis of a wind-induced vibration energy harvester used for the bacterial disinfection of water is mainly considered. The complexification-averaging (CA) method is utilized to analytically calculate the results of the harvester, the model equations of the harvester satisfied are reduced into a set of complex variable equations. The relationship between the displacement amplitude and voltage amplitude is derived under the steady-state case. The amplitudes and phases of both the displacement and voltage are obtained. The analytical solutions of the harvester are then verified by direct numerical simulation. The response mechanism under different parameters is discussed. The frequency island and multi-valued phenomena are found. Meanwhile, it is found that a higher wind speed corresponds to a larger displacement amplitude and voltage. In addition, the RMS voltage and average power are studied. Both have the same variation rules under different excitation amplitudes. Under the same coupling coefficient, load resistance and piezoelectric patch capacitance, the lower the frequency, the easier it is to obtain the larger voltage output. However, the load resistance has the opposite effect on both of them. Finally, to obtain maximum output in a wider frequency region, the optimization and choice of the parameters is studied, and the critical boundary can be identified.

Improving frictional state at fretting interfaces through the covalent structure of diamond–graphite–graphene

This study proposes a novel approach based on the covalent structure of diamond–graphite–graphene (CDGG) to integrate the outstanding properties of diamond, graphite, and graphene, synergistically improving frictional behavior of fretting interfaces. The results demonstrated that in-situ CDGG significantly reduced the alternating stress at the contact interface, the friction coefficient decreased by 40–62 % over pristine diamond coatings under gross slip regime, accompanied by a shorter running-in period. The counterpart pair wear corresponding to in-situ CDGG was lower, and no delamination caused by metal adhesion. The surface graphene/graphite exhibited good frictional toughness, effectively absorbing the relative displacement at contact interface, enabling CDGG to exhibit partial slip regime under higher loads and smaller displacement amplitudes.

Probing the effect of displacement on electrical contact tribological behavior at the risk frequency of nuclear safety DCS equipment

Purpose This paper aims to study the tribological characteristics of the electrical contact system under different displacement amplitudes. Design/methodology/approach First, the risk frequency of real nuclear safety distributed control system (DCS) equipment is evaluated. Subsequently, a reciprocating friction test device which is characterized by a ball-on-flat configuration is established, and a series of current-carrying tribological tests are carried out at this risk frequency. Findings At risk frequency and larger displacement amplitude, the friction coefficient visibly rises. The reliability of the electrical contact system declines as amplitude increases. The wear morphology analysis shows that the wear rate increases significantly and the degree of interface wear intensifies at a larger amplitude. The wear area occupied by the third body layer increases sharply, and the appearance of plateaus on the surface leads to the increase of friction coefficient and contact resistance. EDS analysis suggests that oxygen elements progressively arise in the third layer as a result of increased air exposure brought on by larger displacement amplitude. Originality/value Results are significant for recognizing the tribological properties of electrical connectors in nuclear power control systems. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2024-0098/

Effects of Different Diluents and Freezing Methods on Cryopreservation of Hu Ram Semen.

The purpose of this study was to investigate the effects of different diluents and freezing methods on the quality of thawed sperm after cryopreservation and find an inexpensive and practical method for freezing Hu ram semen for use in inseminations under farm conditions. Ejaculates were collected from five Hu rams. In experiment I, ejaculates were diluted with eight different freezing diluents (basic diluents A, B, C, D, E, F, G, and H). After dilution and cooling, the samples were loaded into 0.25 mL straws and frozen using the liquid nitrogen fumigation method. In experiment II, diluent C was used as the basic diluent and the semen was frozen using liquid nitrogen fumigation and two program-controlled cooling methods. For analysis, frozen samples were evaluated in terms of motility parameters (total motility (TM), progressive motility (PM)), biokinetic characteristics (straight-line velocity (VSL), average path velocity (VAP), curvilinear velocity (VCL), amplitude of lateral head displacement (ALH), wobble movement coefficient (WOB), average motion degree (MAD)), reactive oxygen species (ROS) level, and membrane and acrosome integrity. In experiment I, diluent C had higher TM, PM, and acrosome and membrane integrity and lower ROS compared to other extenders (p < 0.05) except diluent A. Diluent C exhibited higher (p < 0.05) VCL, VAP, ALH, WOB, and MAD compared to diluents B, D, E, and F. In experiment II, TM and all biokinetic characteristics did not show significant differences (p > 0.05) amongst the three freezing methods. Liquid nitrogen fumigation resulted in higher (p < 0.05) PM, membrane integrity, acrosome integrity, and lower ROS level compared to the program. In conclusion, the thawed semen diluted with diluent C had higher quality compared to other diluents. The liquid nitrogen fumigation demonstrated superior semen cryopreservation effects compared to the program-controlled cooling method using diluent C.

Investigation of the profile of the blade considering machining vibration based on finite element analysis

Abstract Vibration is a problem that is easy to occur in the manufacturing process of thin-walled parts such as blades. Through the analysis of modal test results, the role of tool response and blade response in machining vibration is analyzed. With the aid of finite element simulation, the effects of damping ratio, cutting force peak, and force exciting position on the amplitude of response displacement are studied. The profile error caused by the machining vibration is simulated and the peak value of the response displacement amplitude is experimentally verified.

Wear Detection of Bridge Sliding Bearing Based on Temporal Variation of Thermally Induced Daily Displacement Amplitude

Wear Detection of Bridge Sliding Bearing Based on Temporal Variation of Thermally Induced Daily Displacement Amplitude

Detuning piezoelectric receivers by resistive load adjustment for electrodynamic wireless power transfer

This article investigates electrical detuning techniques for low-frequency electrodynamic wireless power transfer (EWPT) systems. This study focuses on protecting the receiver from potential damage when quick increases in magnetic fields occur due to transmitter–receiver distance variation or in-rush transmitter coil currents. In the case of such event, to avoid damaging the mechanical receiver, the solution investigated in this article is to adjust the electrical load connected to the receiver. This adjustment enables precise tuning and detuning of the receiver’s resonant frequency and damping characteristics, thereby allowing to reduce its mechanical displacement amplitude and protecting it from damage. Based on well-known models of EWPT systems, we develop an analysis of two key operational modes of the proposed tuning/detuning approach: maximum transmitted power (MTP) mode, where the receiver circuitry’s input impedance is optimized for peak power transfer, and minimum displacement (MD) mode, which involves electrically detuning the receiver’s resonant frequency to limit its mechanical displacement. We establish transition conditions between MD and MTP modes based on the receiver voltage amplitude, enabling automated monitoring and adjustment of the receiver’s detuning. Experimental validation has been conducted with an EWPT experimental setup and a custom piezoelectric receiver. The results, in good agreement with the proposed analytical model predictions, confirm the effectiveness of the proposed detuning algorithm, which successfully reduces the receiver displacement by 60% in response to sudden magnetic field increases.

СТЕПЕНЬ ВЛИЯНИЯ НЕОТЕКТОНИКИНА СЕЙСМИЧНОСТЬ АБИНСКОГО СЕГМЕНТА СЕВЕРО-ЗАПАДНОГО КАВКАЗА

Relief is one of the sources of information about neotectonic activity. Using structural-geomorphological analysis, it is possible to identify weak zones, which often reflect hidden low-amplitude faults and fracture zones under the surface of Quaternary deposits. Using structural-geomorphological analysis, planation surfaces were identified, displacement amplitudes along faults and the magnitude of neotectonic movements were determined for certain periods of time. The results obtained were compared with seismicity and the degree of inheritance was revealed. 3D computer geological modeling of the stress state also helps in identifying zones of increased neotectonic activity, as the most dangerous zones in terms of seismicity. The stress state and directions of the compression axes in the horizontal plane were calculated using the RMS Roxar software. Also, for a more detailed study of the latest geodynamics of the Abinsk segment, the frequencies of earthquakes and the amount of seismic energy released were analyzed, and frequency graphs were plotted. When comparing the growth deformations of neotectonic uplift structures and the values of the latest stress state with seismicity, their significant correlation was revealed.

Effect of bicarbonate and polyvinyl alcohol on in vitro capacitation and fertilization ability of cryopreserved equine spermatozoa.

Factors contributing to the limited success of in vitro fertilization in horses remain to be studied. In this work, we elucidated the effect of different essential capacitation media components, bicarbonate, and bovine serum albumin or polyvinyl-alcohol, and the incubation microenvironment on sperm parameters associated with capacitation, acrosome reaction, and their ability to activate oocytes via heterologous intracytoplasmic spermatozoa injection in equine cryopreserved spermatozoa. Frozen-thawed spermatozoa underwent incubation at different time intervals in either Tyrode's albumin lactate pyruvate medium (non-capacitating; NC) or Tyrode's albumin lactate pyruvate supplemented with bicarbonate, bicarbonate and polyvinyl-alcohol, bicarbonate and bovine serum albumin, polyvinyl-alcohol and bovine serum albumin alone. Protein kinase A-phosphorylated substrates and tyrosine phosphorylation levels, sperm motility, and acrosome reaction percentages were evaluated. After determining the best condition media (capacitating; CAP), heterologous intracytoplasmic spermatozoa injection on pig oocytes was performed and the phospholipase C zeta sperm localization pattern was evaluated. Incubation of frozen-thawed equine spermatozoa with bicarbonate and polyvinyl-alcohol in atmospheric air for 45min induced an increase in protein kinase A-phosphorylated substrates and tyrosine phosphorylation levels compared to NC condition. Sperm incubation in bicarbonate and polyvinyl-alcohol medium showed an increase in total motility and progressive motility with respect to NC (p ≤ 0.05). Interestingly, three parameters associated with sperm hyperactivation were modulated under bicarbonate and polyvinyl-alcohol conditions. The kinematic parameters curvilinear velocity and amplitude of lateral head displacement significantly increased, while straightness significantly diminished (curvilinear velocity: bicarbonate and polyvinyl-alcohol=120.9±2.9 vs. NC=76.91±6.9µm/s) (amplitude of lateral head displacement: bicarbonate and polyvinyl-alcohol=1.15±0.02 vs. NC=0.77±0.03µm) (straightness: bicarbonate and polyvinyl-alcohol=0.76±0.01 vs. NC=0.87±0.02) (p ≤ 0.05). Moreover, the spontaneous acrosome reaction significantly increased in spermatozoa incubated in this condition. Finally, bicarbonate and polyvinyl-alcohol medium was established as CAP medium. Although no differences were found in phospholipase C zeta localization pattern in spermatozoa incubated under CAP, equine spermatozoa pre-incubated in CAP condition for 45min showed higher fertilization rates when injected into matured pig oocytes (NC: 47.6% vs. CAP 76.5%; p ≤ 0.05). These findings underscore the importance of bicarbonate and polyvinyl-alcohol in supporting critical events associated with in vitro sperm capacitation in the horse, resulting in higher oocyte activation percentages following heterologous intracytoplasmic spermatozoa injection. This protocol could have an impact on reproductive efficiency in the equine breeding industry.

Fretting Wear Behaviors of Silicone Rubber under Dry Friction and Different Lubrication Conditions.

The fretting wear behaviors of silicone rubber under dry friction and different lubrication conditions are studied experimentally. Water, engine oil, dimethyl silicone oil (DSO), and dimethyl silicone oil doped with graphene oxide (DSO/GO) are selected as lubricants. Under the liquid lubrication conditions, the silicone rubber samples are always immersed in the same volume of lubricant. The contact model of a 440C steel ball and silicone rubber sample is the sphere-on-flat contact. The reciprocating fretting wear experiments are carried out using the reciprocating friction wear tester. A scanning electron microscope and three-dimensional white-light interference profilometer are used to detect the surface wear morphology and obtain the wear volume, respectively. The influences of normal force, lubrication condition, and displacement amplitude on fretting wear behavior are discussed. The fretting wear performances of silicone rubber under different fretting states and lubrication conditions are compared. The results show that for a small normal force, silicone rubber has the best wear resistance under DSO/GO lubrication. While for a large normal force, silicone rubber has the best wear resistance under engine oil lubrication.

Mechanical Modeling of Viscous Fluid Damper with Temperature and Pressure Coupling Effects

During long-duration dynamic loads, such as wind loads or seismic effects, the internal temperature and pressure of a damping cylinder escalate rapidly, which induce shifts in the mechanical attributes of viscous fluid dampers (VFDs). This study investigated the mechanical performance of VFD considering the coupling effects of temperature and pressure under long-duration loads. First, we analyzed the mechanical and energy-dissipation performances of the dampers based on the dynamic mechanical tests considering different loading frequencies, displacement amplitude, and loading cycles. The experimental results indicated that both temperature and pressure influenced the output of the dampers, and in the sealed environment of the damper pip, temperature and pressure exerted mutual influence. Furthermore, the relationship between the damping coefficient and temperature–pressure coupling effects was obtained. Subsequently, an improved mathematical model for the mechanical performance of a gap-type VFD was proposed by considering the macroscopic energy balance of the entire fluid within the damper. Finally, the accuracy of the mathematical model for VFD under long-duration dynamic loads was validated by comparing the computational results with the experimental data.

Experimental and theoretical investigation on magnetorheological elastomers containing carbonyl iron particles coated with silane coupling agent

Magnetorheological (MR) elastomer composites, comprising soft silicone rubber, various additives, and different weight fractions of carbonyl iron particles (CIPs) coated with silane coupling agent, are produced via a novel manufacturing process in an anisotropic state. This study encompasses both experimental and modeling investigations into the dynamic viscoelastic properties of magnetorheological elastomer (MREs) in shear mode under varying magnetic fields, displacement amplitudes, and frequencies. Two MRE vibration mitigation devices are fabricated to experimentally assess the shear storage modulus and the loss factor of MREs. The experimental findings reveal a pronounced MR effect in the MRE devices, where both the shear storage modulus and the loss factor increase with rising magnetic fields, frequencies, and particle weight fractions, yet decrease with higher displacement amplitudes. A modified fractional-derivative equivalent parametric model, grounded in a magnetic field- and frequency-dependent shear modulus model along with internal variable theory, is proposed to describe the effects of these key influencing factors on the MREs’ dynamic viscoelastic properties. Comparative analysis of experimental and numerical data demonstrates that this refined mathematical model can accurately represent the dynamic viscoelastic properties of MREs.

Rapid Finite-Fault Models for the 2023 Mw 7.8 Kahramanmaraş, Türkiye, Earthquake Sequence

Abstract In the immediate aftermath of devastating earthquakes such as in the 6 February 2023 Kahramanmaraş sequence in southcentral Türkiye, key stakeholders and the public demand timely and accurate earthquake information. Especially for large events, finite-fault models provide important insights into the rupture process and enable interpretation of the observed ground shaking, which can improve situational awareness and facilitate rapid assessment of future hazards. Using strong-motion waveforms recorded during the Kahramanmaraş sequence, we simulate a real-time playback and calculate how a finite-source model computed with the Finite-fault rupture Detector (FinDer) algorithm would evolve for the Mw 7.8 Pazarcık, Mw 7.6 Elbistan, and Mw 6.4 Yayladağı earthquakes. Using template matching FinDer compares observed and predicted ground-motion acceleration amplitudes to determine the orientation and spatial extent of fault rupture. We test both generic crustal and fault-specific templates from ground-motion models and rupture geometries of the east Anatolian and Çardak–Sürgü faults. In the second step, we estimate the seismic slip along the source models from the backprojection of the seismic displacement amplitudes. The algorithms achieve excellent performance for all three earthquakes, and the final source models and slip profiles available within tens of seconds of the rupture nucleation match well with models computed days to weeks after the events occurred. The temporal evolution of the source models for the Pazarcık and Elbistan earthquakes suggests that FinDer can provide insight into the rupture kinematics of large earthquakes. Cascading instrument failures as well as power and data telemetry interruptions during the Pazarcık earthquake led to an early termination of signals at a significant number of near-source stations. We show that FinDer is robust enough to cope with this type of degradation in network performance that can occur in large earthquakes, in general.

Investigating fretting wear mechanisms in Ti-6Al-4V: insights from residual stress and equivalent plastic strain analysis

Purpose The study delves into the influence of wear cycles on these parameters. The purpose of this paper is to identify characteristic patterns of σRS and εPEEQ that discern varying wear situations, thereby contributing to the enrichment of wear theory. Furthermore, the findings serve as a foundational basis for nondestructive and in situ wear detection methodologies, such as nonlinear ultrasonic detection, known for its sensitivity to σRS and εPEEQ. Design/methodology/approach This paper elucidates the wear mechanism through the lens of residual stress (σRS) and plastic deformation within distinct fretting regimes, using a two-dimensional cylindrical/flat contact model. It specifically explores the impact of the displacement amplitude and cycles on the distribution of residual stress and equivalent plastic strain (εPEEQ) in both gross slip regime and partial slip regimes. Findings Therefore, when surface observation of wear is challenging, detecting the σRS trend at the center/edge, region width and εPEEQ distribution, as well as the maximum σRS distribution along the depth, proves effective in distinguishing wear situations (partial or gross slip regimes). However, discerning wear situations based on εPEEQ along the depth direction remains challenging. Moreover, in the gross slip regime, using σRS distribution or εPEEQ along the width direction rather than the depth direction can effectively provide feedback on cycles and wear range. Originality/value This work introduces a novel perspective for investigating wear theory through the distribution of residual stress (σRS) and equivalent plastic strain (εPEEQ). It presents a feasible detection theory for wear situations using nondestructive and in situ methods, such as nonlinear ultrasonic detection, which is sensitive to σRS and εPEEQ. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0005/

Analytical design of non-grounded tuned mass-damper-inerter for base-excited structures

This research contributes new analytical formulae for H∞ optimal tuning of non-grounded tuned mass-damper-inerter (TMDI) for minimizing free-end displacement of base-excited cantilevered structures. The derivation relies on the fixed-point theory, making use of single-mode modelling of the cantilevered structure while accommodating arbitrary TMDI placement along the structural height. Optimal TMDI tuning parameters are derived for given dominant mode shape of structure and TMDI inertial properties (i.e., secondary mass and inertance) under two different types of harmonic excitations with frequency-independent displacement and acceleration amplitudes. The applicability of the derived TMDI tuning formulae for response mitigation of lightly damped cantilevered structures under stationary broadband support excitation is established through comparisons with numerically optimal TMDI properties for a wide range of TMDI inertial properties. Moreover, the analytical TMDI tuning formulae derived in this study achieve enhanced structural performance for base-excited structures compared to those from the literature, derived under various modelling assumptions and optimality criteria. Lastly, the potential of the proposed TMDI tuning for structural response mitigation is numerically evaluated by examining displacement, acceleration, and energy dissipation response history data of an experimentally identified reinforced concrete bridge pier model subjected to 100 earthquake ground motion (GM) records. Overall, reported results demonstrate that the derived analytical formulae can significantly extend the practical application of TMDI as a bona fide dynamic vibration absorber for base-excited structures by circumventing the need for computationally demanding numerical TMDI tuning optimization.

Parametric Dynamic Simulation and Bayesian Design Optimization of a Front-Loading Washing Machine

Abstract Objective This paper presents the dynamic modeling and design optimization of a fully parametrized front-loading washing machine. Methods A thorough mathematical analysis is performed to capture the effect of nine design variables (including rotation speed, spring stiffness, weight balancer mass density, damping coefficient, spring and damper angles) on vibrational characteristics of the washing machine. The parametric simulation reveals a complex relationship between the vibrational dynamics and design variables, entailing a computationally efficient optimization approach. A Bayesian Optimization (BO) framework is developed, in which a Gaussian process model and Genetic Algorithm (GA) are utilized along with carefully selected acquisition functions to enable adaptive sampling and search for optimal design values. The objective function is to minimize the maximum amplitude of the tub displacement inside the washing machine body. Two case studies are performed to consider a different number of design variables and choices of various infill methods. Results Results show that the fully parametrized front-loading washing machine model is applicable for parametric simulation and design optimization. The proposed BO is able to successfully find a set of design variable values corresponding to the lowest maximum displacement for vibration reduction. A comparison analysis is also carried out to exhibit the difference in optimization convergence and computational cost caused by the choice of acquisition functions. Conclusion It is shown that the fully parametrized washing machine model yields a lower maximum displacement than the model with fewer design variables. Of the two acquisition functions studied for optimization, the Expected Improvement function converges more rapidly than the Lower Bound criterion.

Vibration controlling effect of tuned liquid column damper (TLCD) on support structural platform (SSP)

A bidirectional fluid-structure coupling model between tuned liquid column damper (TLCD) and support structural platform (SSP) was developed to study effects of TLCD-SSP mass ratio and tuning ratio on reducing SSP vibration. Laboratory experiments of TLCD interaction with SSP were conducted to validate TLCD-SSP coupling model. Good agreements between numerical results and experimental data are obtained. TLCD/SSP mass ratio increases from 1% to 3%, the maximum amplitude of SSP upper displacement decreases from 43.77% to 78.32%, and the upper acceleration damping rate increases from 43.26% to 77.88%. There is a phase differences between dynamic water pressure offered by sloshing inside TLCD and upper displacement curves, and the damping energy dissipation effect is maximized when the hysteresis phase difference reaches π/2. The larger mass ratio is more effective in suppressing the structural vibration. But it also brings about a fundamental frequency drift. It is advised that the mass ratio of water in TLCD to SSP should be 1.5%, the total mass of water and shell of TLCD should be about 2.5% of the mass of SSP, and the intrinsic frequencies of TLCD and SSP should be tuned the same so that the vibration controlling performance of TLCD can be improved maximally.