Ambient Temperature Research Articles

Experimental study on exhaust internal circulation desiccant wheel evaporative cooling chiller

Evaporative cooling chillers reduce the water temperature by absorbing heat during the evaporation of water without the need for compressor assistance or refrigerants. It is an energy-saving and environmentally friendly cooling technology but it needs necessary improvements in the applicable environmental area and refrigeration performance due to ambient air wet-bulb temperature limitations. To obtain chilled water below the dew-point temperature of the ambient air, an exhaust internal circulation desiccant wheel evaporative cooling chiller is proposed and experimentally investigated. A combination of a heat pipe exchanger, a desiccant wheel, an air cooler and an air heater are applied to reduce the wet-bulb temperature of the ambient air before it passes through the direct evaporative cooler. At the same time, the low-temperature and low-humidity exhaust air from the direct evaporative cooler is used to circulate to improve chiller performance. The experimental results show that the average chilled water temperature of the proposed chiller is 10.2 ℃ lower than that of the direct evaporative cooling chiller under five typical environmental conditions. The wet-bulb efficiency of the proposed chiller is the highest at high temperatures and high humidities (36 ℃ and 80% RH), which is 6 times greater than that of direct evaporative cooling chillers. Therefore, the proposed chiller expands the application range of evaporative cooling technology, which is especially suitable for humid areas with low-grade heat utilization such as solar energy.

Modeling of micron-sized aluminum particle combustion in hot gas flow

This paper presents a model for micron-sized aluminum (Al) particle combustion in hot oxidizing environments, forming hollow spheres. The model comprises four sub-models describing the physical and chemical processes during Al combustion: melting of the solid core, ejection of liquid Al droplets from the breaking solid shell, vaporization of liquid droplets, and ignition and establishment of vapor flame surrounding the solid particles. The model is of critical importance when the ambient gas temperature is higher than the melting point of the Al core, Tc,m, but lower than the alumina (Al2O3) shell’s melting point, Ts,m. In the model, the Al core is assumed to be surrounded by a thin, compact alumina shell that blocks the diffusion of oxidizer into the core and prevents surface reactions. The alumina shell’s cracking and liquid Al’s eruption are triggered by thermal expansion and pressure buildup in the liquid core. The splashed liquid Al droplets vaporize quickly and initiate gas-phase reactions, followed by the vaporization of the liquid Al core as the particle temperature Tp increases. Al vapor combustion heat is redistributed to simulate the gaseous flame near the particle. The model is implemented using the Lagrangian particle tracking method and is validated through simulations of micron-sized Al particle combustion in hot gas and comparison with experiments. The results can explain the formation of the sharp-edged holes on hollow aluminum oxide spheres and the ignition behavior observed in the experiments.

ANFIS-based improved GWO: Rapid prototyping of low-power solar energy system under fast-changing solar radiation conditions

The increasing need for energy, coupled with progress in technology, has emphasized the importance of renewable energy sources around the world. Solar energy systems harness the power of sunlight to generate electricity, offering a renewable and environmentally friendly alternative to conventional energy sources. Maximum Power Point Tracking (MPPT) algorithms are employed to achieve optimal efficiency from the PV systems. This paper introduces a new method for controlling Maximum Power Point (MPP) in battery charging systems using an Adaptive Neuro-Fuzzy Inference System (ANFIS)-based improved Grey Wolf Optimization (ANFIS-GWO) algorithm. The study involves the application and evaluation of the IGWO algorithm under fast-changing solar radiation conditions (1000 w/m2, 600 w/m2, 800 w/m2) and constant ambient temperature (25 °C). An analysis was performed to evaluate the behavior of the system in the laboratory environment using rapid prototyping. The proposed IGWO algorithm demonstrates improved accuracy compared to traditional methods in the current literature. The study aims to enhance the efficiency of MPPT control in photovoltaic (PV) systems, offering a potential solution for optimizing performance in different solar radiation conditions.

Improved ammonia sensitivity and broadband photodetection by using PBTTT-C14/WS2-QDs nano-heterojunction based thin film transistor

An ambient temperature broadband photo-detector and ammonia (NH3) gas sensor devices are developed with PBTTT-C14/WS2-QDs heterojunction thin film. This composite thin film of PBTTT-C14 conjugate polymer and hydrothermally synthesized WS2-QDs have been deposited by high yield and cost-effective ‘floating film transfer method’ (FTM), which works as a channel (p-type) of the thin film transistor (TFT). To determine the NH3 sensing behavior of the TFT, different concentrations of analyte (0.5–20 ppm) have been exposed on the channel of the TFT, which shows the response of ∼ 50 % at 10 ppm ammonia concentration that is significantly higher than PBTTT-C14 only TFT. This improvement is made possible by the NH3-responsive depleted layer of polymer/QDs heterojunction, which varies widely in the presence of ammonia. As a consequence, the ON/OFF ratio, carrier mobility and threshold voltage (Vth) of the device changes in a wider range. Besides, this TFT based gas sensor is also highly selective to the other interfering gases. In addition to NH3 gas sensitivity, This TFT also shows very high photosensitivity under white light illumination that enhances ‘ON’ and ‘OFF’ current of the device by ∼ 2.2 and 70 times, respectively under one sun white light illumination, whereas Vth of the device is shifted by ∼ 22 V. Besides, the device shows quite fast response/ recovery time under NH3 gas exposure and light illumination.

Convolutional denoising for large-volume Seebeck calorimeter

Ambient temperature fluctuations can affect the thermal noise and sensitivity of a large-volume Seebeck calorimeter. This paper proposes that a reference cell considerably smaller than the sample cell in the apparatus can effectively neutralize this noise. It is found that the thermal signals from both the reference and sample cells exhibit a convolution relationship. By deconvolving two distinct thermal pulses generated by abrupt changes in cooling fluid temperature, one from the reference cell and one from the sample cell, a corresponding response function is derived. And using this function, the noise is canceled out by subtracting the convoluted signal of the reference cell from that of the sample cell during isothermal calorimetry. Experimentally, utilizing this technique with two calorimeters, one with a 17.6-liter capacity and the other with a 27-liter capacity, has been shown to reduce noise by at least 5 % and 6 % from their initial values, respectively.

Heat Effects during the Operation of Lead-Acid Batteries

Thermal events in lead-acid batteries during their operation play an important role; they affect not only the reaction rate of ongoing electrochemical reactions, but also the rate of discharge and self-discharge, length of service life and, in critical cases, can even cause a fatal failure of the battery, known as “thermal runaway.” This contribution discusses the parameters affecting the thermal state of the lead-acid battery. It was found by calculations and measurements that there is a cooling component in the lead-acid battery system which is caused by the endothermic discharge reactions and electrolysis of water during charging, related to entropy change contribution. Thus, under certain circumstances, it is possible to lower the temperature of the lead-acid battery during its discharging. The Joule heat generated on the internal resistance of the cell due to current flow, the exothermic charging reaction, and above all, the gradual increase in polarization as the cell voltage increases during charging all contribute to the heating of the cell, overtaking the cooling effect. Of these three sources of thermal energy, Joule heating in polarization resistance contributes the most to the temperature rise in the lead-acid battery. Thus, the maximum voltage reached determines the slope of the temperature rise in the lead-acid battery cell, and by a suitably chosen limiting voltage, it is possible to limit the danger of the “thermal runaway” effect. The overall thermal conditions of the experimental cell are significantly affected by the ambient temperature of the external environment and the rate of heat transfer through the walls of the calorimeter. A series of experiments with direct temperature measurement of individual locations within a lead-acid battery uses a calorimeter made of expanded polystyrene to minimize external influences. A hitherto unpublished phenomenon is discussed whereby the temperature of the positive electrode was lower than that of the negative electrode throughout the discharge, while during charging, the order was reversed and the temperature of the positive electrode was higher than that of the negative electrode throughout the charge. The authors relate this phenomenon to the higher reaction entropy change of the active mass of the positive electrode than that of the negative electrode.

Temperature influence on the natural and forced vibrations of laminate plates with fractional Zener viscoelastic layers

The paper is devoted to the analysis of the influence of ambient temperature on the linear free and non-linear harmonic vibrations of laminate plates with viscoelastic layers. The Zener fractional material model is adopted. The plate kinematics is described using the refined zig-zag theory. The formulation of vibrations of the plate is based on the physical law with the separation of deviatoric and volumetric deformation. The temperature influence is included using the frequency-temperature superposition principle. The shift factor applied to modify the damping properties of the viscoelastic material is computed using the Willams-Landel-Ferry formula.The paper contains the results of several analyses of laminate plates with various viscoelastic materials for which the material data were available in the literature. In particular, the analyses focus on determination of the properties characteristic for the plates with Zener fractional model under the influence of the ambient temperature.

Effects of pre-exercise glycerol supplementation on dehydration, metabolic, kinematic, and thermographic variables in international race walkers.

Due to the increase in global temperature, it is necessary to investigate solutions so that athletes competing in hot conditions can perform in optimal conditions avoiding loss of performance and health problems. Therefore, this study aims to evaluate the effect of pre-exercise glycerol supplementation during a rectangular test at ambient temperature mid (28.2ºC) on dehydration variables in international race walkers. Eight international male race walkers (age: 28.0 years (4.4); weight: 65.6 kg (6.6); height: 180.0 cm (5.0); fat mass: 6.72% (0.66); muscle mass: 33.3 kg (3.3); VO2MAX: 66.5 ml · kg-1·min-1 (1.9)) completed this randomized crossover design clinical trial. Subjects underwent two interventions: they consumed placebo (n = 8) and glycerol (n = 8) acutely, before a rectangular test where dehydration, RPE, metabolic, kinematic, and thermographic variables were analyzed before, during and after the test. After the intervention, significant differences were found between groups in body mass in favor of the placebo (Placebo: -2.23 kg vs Glycerol: -2.48 kg; p = 0.033). For other variables, no significant differences were found. Therefore, pre-exercise glycerol supplementation was not able to improve any dehydration, metabolic, kinematic, or thermographic variables during a rectangular test at temperature mid in international race walkers. Possibly, a higher environmental temperature could have generated a higher metabolic and thermoregulatory stress, generating differences between groups like other previous scientific evidence.

Structural Investigation of Orthoborate-Based Electrolytic Materials for Fuel Cell Applications

The paper presented delivers the proof for one of the possible solutions to the so-called medium-temperature gap—the lack of electrolytic systems able to efficiently work in a temperature range spanning from 200 to 450 °C. Regardless of the progress made in this field, the commercially available systems are still operating either at close to ambient temperatures, where hydrogen purity requirements are a significant limit, or above ca. 600 °C, where they suffer from increased corrosion and excessive thermal stresses occurring during startup and shutdown. Alkali metal orthoborates (M3BO3 M = Li, Na, K, or the mixture of these), in contrast to commercially used tetra-(M2B4O7) and meta-(MBO2) borates of these metals, are compounds with relatively poorly understood structure and physicochemical properties. The possibility of their application as an electrolyte in a fuel cell is a relatively new idea and has been preliminary reported. Therefore, an extended phase-focused analysis of the materials applied was needed to re-optimize both the synthetic strategy and the application route. Results of PXRD and FT-IR investigations showed, on the one hand, a complicated multi-phase structure, including the main orthoborate phase, as well as the presence of additional borate-based phases, including boric oxoacid. On the other hand, DTA tests proved not only that their melting temperatures are lower than these characteristics for the tetra- and meta-counterparts, but also that cation mixing leads to a subsequent decrease in this important functional parameter of the materials studied.

Experimental studies of a remote device for biometric identification of the pre-mastitis state of the udder of dairy cows

Analysis of development of dairy cattle breeding in the Republic of Belarus is presented. The problems of reducing milk productivity and the period of economic use of dairy cows as a result of mastitis disease are noted. The importance of timely detection of sick animals, as well as treatment of the inflammatory process of the udder in the early stages is noted. The results of theoretical and experimental studies of a mock-up sample of a biometric identification device for the pre-mastitis state of udder of dairy cows are presented. In the course of experimental studies, a significant influence of ambient temperature on the thermal imaging picture was revealed, based on which the values of the radiation coefficient for cows were determined. The final adjustment of the previously established temperature ranges was made when determining one or another form of mastitis, namely, within 32.0−36.3 ℃ – the range of normal temperatures, 36.4−37.7 ℃ – “Subclinical mastitis”, 37.8−39.0 ℃ – “Clinical mastitis”. The most significant factors and optimization parameter have been determined. The percentage of the useful area of the studied object is selected as the optimization parameter. Based on the processing of experimental data, a mathematical model is obtained, described by a regression equation in the form of a polynomial of the second degree. The rational parameters of the device for biometric identification of the pre-mastitis state of the udder of dairy cows were obtained, namely: the angle of inclination of the thermal imaging module αо – 2,7o, the focal length to the object l – 794 mm, installation height of the thermal imaging module h – 495 mm. Also, based on the conducted research, priority areas and opportunities for development of the domestic agro-industrial complex through creation of integrated systems for monitoring the physiological state of animals within the framework of development of digital automated technologies of a “smart” farm have been identified.

Size effect of compressive performance of concrete under elevated temperatures: Tests and meso-scale analysis

This study investigates the size effect of concrete under ambient and elevated temperatures through tests and numerical simulations. Compressive performance of prismatic and cylindrical concrete specimens with varying dimensions were tested at temperatures ranging from ambient temperature to 600°C. Meso-scale finite element analysis (FEA), assuming that the mechanical properties of matrix and interfacial transition zones (ITZ) followed Weibull distribution, was employed to simulate the tested specimens and to conduct parametric analysis on specimens with larger or smaller sizes and under temperatures up to 800°C. Both experimental and numerical results showed that the cracks on the specimen surface became finer and denser as an increase of specimen sizes under elevated temperatures. A noticeable decrease in concrete compressive strength with increasing specimen dimensions was observed below 600°C, but peak strain and elastic modulus did not exhibit significant size effect. Size effect on strength diminished at temperatures exceeding 800°C. Classic Size Effect Laws (SEL), such as Weibull's and Bažant's SEL, were applicable to characterize the size effect on strength of specimens within common lab test dimensions under elevated temperatures. Based on the results from experiments, FEA and Bažant's SEL, a stress-strain model under elevated temperatures considering size effect was proposed. The predicted results from this model showed good agreement with test results.

Optomechanical industrial-level camera modifications forrepeatable thermal image drift

Thermal image drift is observed in prevalent industrial-level cameras because their optomechanical design is not optimised to reduce this phenomenon. In this paper, the effect of temperature on industrial-level cameras is investigated, focusing on the thermal image drift resulting from ambient temperature changes and warming-up process. Standard methods for reducing thermal image drift are reviewed, concentrating on the lack of repeatability aspect of this drift. Repeatable thermal image drift is crucial for applying a compensation model as random thermal deformations in sensors cannot be compensated. Moreover, the possible cause of this issue is explored, and novel optomechanical camera modifications are proposed that maintain the thermal degrees of freedom for the deforming sensor, limiting the lack of repeatability aspect of thermal image drift to a low level. The improvement is verified by conducting experiments using a specialised test stand equipped with an invar frame and thermal chamber. Considering the results from the application of the polynomial compensation model, the standard deviation of the central shifts of image drift is reduced by ×3.99, and the absolute range of image drift is reduced by ×2.53.

Greenspaces And Cardiovascular Health.

Accumulating evidence suggests that living in areas of high surrounding greenness or even brief exposures to areas of high greenery is conducive to cardiovascular health, which may be related to the environmental, social, psychological, and physiological benefits of greenspaces. Recent data from multiple cross-sectional, longitudinal, and cohort studies suggest that living in areas of high surrounding greenness is associated with a lower risk of all-cause and cardiovascular mortality. High levels of neighborhood greenery have been linked also to a decrease in the burden of cardiovascular disease risk factors as reflected by lower rates of hypertension, dyslipidemia, and diabetes. Those who live in greener environments report better mental health and more frequent social interactions, which can benefit cardiovascular health as well. In this narrative review, we discuss evidence linking greenspaces to cardiovascular health as well as the potential mechanisms underlying the beneficial effects of greenspaces, including the impact of vegetation on air, noise and light pollution, ambient temperature, physical activity, mental health, and biodiversity. We review literature on the beneficial effects of acute and chronic exposure to nature on cardiovascular disease risk factors, inflammation and immune function, and we highlight the potential cardiovascular effects of biogenic volatile organic compounds that are emitted by trees and shrubs. We identify current knowledge gaps in this area and underscore the need for additional population studies to understand more clearly and precisely the link between greenness and health. Such understanding is urgently needed to fully redeem the promise of greenspaces in preventing adverse environmental exposures, mitigating the effects of climate change, and creating healthier living environments.

Stability of serum placental growth factor (PlGF) and soluble fms-like tyrosine kinase 1 (sFlt-1)

Placental growth factor (PlGF) and soluble fms-like tyrosine kinase 1 (sFlt-1) are biomarkers used for diagnosis and risk estimation of preeclampsia. Stability in room temperature (RT) may affect the usefulness of these analyses, as shipping at ambient temperature is the most practical and suitable way to ship samples. To date, scientific studies of such stability are lacking. We aimed to assess the stability of PlGF and sFlt-1 at RT in serum from pregnant women. In addition, a smaller study of stability at 4 °C was performed. Serum was collected from 69 pregnant women and stored at RT or at 4 °C for up to 192 h. Analytes were considered stable if the mean percent change ± 90 confidence interval of the mean was within the baseline concentration ± allowable bias. Allowable bias was calculated from data on biological variation. In addition, an instability equation was calculated to assess loss of stability, in line with recent European Federation of Clinical Chemistry and Laboratory Medicine (EFLM) recommendations. The mean percent change was <3.5% for PlGF, <1% for sFlt-1 and <4.5% for sFlt-1/PlGF ratio up to 192 h. PlGF was considered stable for 168 h, and sFlt-1 and sFlt-1/PlGF ratios were considered stable for 192 h at RT. At 4 °C, PlGF was considered stable for 120 h, sFlt-1 for 168 h and sFlt-1/PlGF ratio for 120 h. Both PlGF and sFlt-1 as well as sFlt-1/PlGF ratio show sufficient stability (minimum 168 h) for samples to be shipped at RT.

A thermostable ionic liquid-methacrylate-based polymer electrolyte for energy storage application

In recent years, gel polymer electrolytes (GPEs) incorporating ionic liquids (ILs) have been explored extensively for lithium-ion batteries due to their favourable thermal stability and high ionic conductivity. Gel polymer electrolytes can also improve the safety of lithium-ion batteries by eliminating the flammable organic solvents which are often used in traditional electrolyte systems. Herein, we report an efficient synthesis of a thermostable ionic liquid-methacrylate-based polymer gel electrolyte via a photo-initiated phase separation (PIPS) process in an inert environment. Anionic liquid phase of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIMTFSI), coupled with a low molecular weight polyethylene glycol dimethyl ether (PEGDME), was combined with a solid phase of bisphenol A ethoxylate dimethacrylate (BEMA) at varying solid to liquid ratios to produce a thermally stable gel electrolyte. The highest ionic conductivity of 1.9 × 10−3 S cm−1 (at 30 °C) was achieved for the electrolyte with a solid-to-liquid ratio of 1:3 by weight. The Lithium metal cells utilizing these electrolytes and LiFePO4 as cathode active material exhibited the initial discharge capacity of 144 mAh g−1 with capacity retention of 85 % over 100 cycles in ambient temperature. The thermal stability of the cells was significantly improved upon increasing the EMIMTFSI content. This study illustrates the potential application of the IL-methacrylate gel polymer electrolyte system in enhancing the safety of Li-ion batteries through careful tuning of the composition. Their versatile properties also make them suitable for quasi-solid-state batteries with high energy density and safety.

Design of a two-renewable energy source-based system with thermal energy storage and hydrogen storage for sustainable development

A renewable energy-based system, including an energy storage subsystem, is designed within the scope of this proposed study to meet the fresh water and electricity demands of a community. The city of Imperial in the state of California is, in this regard, considered for a case study. The energy storage solutions are incorporated into the system to enhance the flexibility and efficiency of energy systems since solar and wind energy resources fluctuate. These energy storage options help offset the mismatch between demand and supply to provide feasible solutions practically. The current system employs storage technologies, such as thermal energy storage (TES) and hydrogen, to efficiently store excess energy for usage during peak demand periods. The parabolic through solar collector (PTSC) and wind turbine in the system are modelled using the System Advisor Model (SAM). Furthermore, the energy and exergy aspects of thermodynamic are considered when performing the thermodynamic analysis of the entire system. The Engineering Equation Solver (EES) is employed to construct the programming codes and perform a thermodynamic analysis of the overall system and its components. The effects of varying numerous parameters on the system performance are studied in this proposed study using a parametric investigation which is carried out through the changes in the ambient temperature, source temperatures, and mass flow rate of the current system. The results of this study show that the annual net amount of electricity generated by the proposed system is 74.90 GWh, which meets 11.7 % of the residential electricity needs of the Imperial City. The desalination unit in the system is also able to produce fresh water from seawater, meeting the needs of 4708 families. The current system further produces a total of 3379.53 tons of fresh water and 226.98 tons of H2 annually. As a result of the energy and exergy analyses performed for the designed system, the energy and exergy efficiencies for the overall system are found to be 47.5 % and 34.3 %, respectively.

Microstructure and fracture toughness of 850°C quenched and aged Zr-2.5Nb alloy

The Zr-2.5Nb alloy pressure tubes manufactured by Water Quenched and Aged (WQA) fabrication route has reportedly exhibited superior resistance against in-reactor dimensional changes. WQA route comprises three consecutive thermo-mechanical treatments viz., solution heat treatment (SHT), cold working and vacuum aging, which govern the final microstructure and therefore fracture toughness of the pressure tube material. This work describes the influence of SHT soaking duration, degree of cold working and aging temperature on the microstructure and fracture toughness of WQA Zr-2.5Nb alloy. WQA pressure tubes are expected to have better resistance to in-reactor dimensional changes. However, if proper care of hydrogen absorption during thermo-mechanical processing is not taken, though resistance to creep will improve expectedly but fracture toughness at ambient temperature will deteriorate.

Population ecology of the intertidal xanthid crab Leptodius exaratus (H. Milne Edwards, 1834) (Decapoda: Brachyura: Xanthidae) on rocky shores in Kuwait, Arabian (Persian) Gulf

Abstract Leptodius exaratus (H. Milne Edwards, 1834) is an exploited species that has been used as bait for recreational fishing in Kuwait. The biological and ecological aspects of the species required to manage this practice are limited. We investigated the life history and population ecology of L. exaratus in the northwestern Arabian (Persian) Gulf. The spawning season of the crab in Kuwait starts in the late spring and continues through the summer and ends in September. Fecundity is highly correlated to female body size and ranges 2,533–11,991 eggs clutch–1, with a mean number of 7,055 eggs clutch–1. Juveniles are generally recruited between July and September, with lower minor recruitment levels occurring in October and November. Growth is highly seasonal, being slow during the cold season (October-February) and high during the warmer season (March and September), with a higher growth rate in males than in females. The seasonality of growth and reproduction of L. exaratus in the region is strongly related to ambient air and water temperatures. Sexual dimorphism is highly significant between males and females with males, reaching reproductive maturity at 17.43 ± 0.53 mm carapace width (CW) and females at 9.58 ± 1.21 mm CW. The overall sex ratio for the species is 0.8:1 (males:females). Furthermore, the life span of 3–4 yr and an overall mortality slightly higher in males than in females. The results of our study could be used to determine fishery management strategies such as minimum catch sizes and closures periods. The results on life history and dynamics of the complex life cycle of L. exaratus contribute to conservation and sustainable exploitation of the species in Kuwait.

Personal Strategies to Reduce the Cardiovascular Impacts of Environmental Exposures.

Ubiquitous environmental exposures increase cardiovascular disease risk via diverse mechanisms. This review examines personal strategies to minimize this risk. With regard to fine particulate air pollution exposure, evidence exists to recommend the use of portable air cleaners and avoidance of outdoor activity during periods of poor air quality. Other evidence may support physical activity, dietary modification, omega-3 fatty acid supplementation, and indoor and in-vehicle air conditioning as viable strategies to minimize adverse health effects. There is currently insufficient data to recommend specific personal approaches to reduce the adverse cardiovascular effects of noise pollution. Public health advisories for periods of extreme heat or cold should be observed, with limited evidence supporting a warm ambient home temperature and physical activity as strategies to limit the cardiovascular harms of temperature extremes. Perfluoroalkyl and polyfluoroalkyl substance exposure can be reduced by avoiding contact with perfluoroalkyl and polyfluoroalkyl substance-containing materials; blood or plasma donation and cholestyramine may reduce total body stores of perfluoroalkyl and polyfluoroalkyl substances. However, the cardiovascular impact of these interventions has not been examined. Limited utilization of pesticides and safe handling during use should be encouraged. Finally, vasculotoxic metal exposure can be decreased by using portable air cleaners, home water filtration, and awareness of potential contaminants in ground spices. Chelation therapy reduces physiological stores of vasculotoxic metals and may be effective for the secondary prevention of cardiovascular disease.

Lectin binding to pectoral fin of neonate little skates reared under ambient and projected-end-of-century temperature regimes.

The glycosylation of macromolecules can vary both among tissue structural components and by adverse conditions, potentially providing an alternative marker of stress in organisms. Lectins are proteins that bind carbohydrate moieties and lectin histochemistry is a common method to visualize microstructures in biological specimens and diagnose pathophysiological states in human tissues known to alter glycan profiles. However, this technique is not commonly used to assess broad-spectrum changes in cellular glycosylation in response to environmental stressors. In addition, the binding of various lectins has not been studied in elasmobranchs (sharks, skates, and rays). We surveyed the binding tissue structure specificity of 14 plant-derived lectins, using both immunoblotting and immunofluorescence, in the pectoral fins of neonate little skates (Leucoraja erinacea). Skates were reared under present-day or elevated (+5°C above ambient) temperature regimes and evaluated for lectin binding as an indicator of changing cellular glycosylation and tissue structure. Lectin labeling was highly tissue and microstructure specific. Dot blots revealed no significant changes in lectin binding between temperature regimes. In addition, lectins only detected in the elevated temperature treatment were Canavalia ensiformis lectin (Concanavalin A) in spindle cells of muscle and Ricinus communis agglutinin in muscle capillaries. These results provide a reference for lectin labeling in elasmobranch tissue that may aid future investigations.