Ambient Sonic-spray Ionization Mass Research Articles

Analyzing Brazilian Vehicle Documents for Authenticity by Easy Ambient Sonic‐Spray Ionization Mass Spectrometry*

Using desorption/ionization techniques such as easy ambient sonic-spray ionization mass spectrometry (EASI-MS), it is possible to analyze documents of Brazilian vehicles for authenticity, providing a chemical profile directly from the surface of each document. A method for the detection of counterfeit documents is described, and the falsification procedure is elucidated. Forty authentic and counterfeit documents were analyzed by both positive and negative ion modes, EASI(±)-MS. EASI(+)-MS results identified the presence of (bis(2-ethylhexyl)phthalate plasticizer and of dihexadecyldimethylammonium biocide in both types of documents. For EASI(-)-MS results, the 4-octyloxybenzoic acid additive ([M + H](+): m/z 249) is present only in counterfeit documents. It was also found that counterfeit vehicle documents are produced via Laserjet printers. Desorption/ionization techniques, such as EASI-MS, offer therefore, an intelligent way to characterize the counterfeiting method.

Direct monitoring of drug degradation by easy ambient sonic-spray ionization mass spectrometry: the case of enalapril

Using enalapril maleate as a test case, the ability of ambient mass spectrometry, namely, via easy ambient sonic-spray ionization mass spectrometry (EASI-MS), to perform direct monitoring of drug degradation has been tested. Two manufacturing processes were investigated (direct compression and wet granulation), and the formation of degradation products was measured via both EASI-MS and high-performance liquid chromatography with ultraviolet detection for a total period of 18 months. Both techniques provide comparable results, which indicate that direct analysis by ambient mass spectrometric techniques presents a viable alternative for drug degradation monitoring with superior simplicity, throughput, and reliability (no sample manipulation), and comparable quantitative results. In terms of qualitative monitoring, the full mass spectra with intact species provided by EASI-MS allow for comprehensive monitoring of known and unknown (or unexpected) degradation products.

Distinct hepatic lipid profile of hypertriglyceridemic mice determined by easy ambient sonic-spray ionization mass spectrometry

Easy ambient sonic-spray ionization mass spectrometry (EASI-MS) was used to interrogate the hepatic lipid profiles of hypertriglyceridemic and control normotriglyceridemic mice. The analyses of ex vivo complex lipid mixtures were made directly with EASI-MS without accompanying separation steps. Intense ions for phosphatidylcholines and triacylglycerols were observed in the positive ion mode whereas the spectra in the negative ion mode provided profiles of phosphatidylethanolamines and phosphatidylinositol. EASI-MS was coupled to high-performance thin-layer chromatography for analysis of free fatty acids. Fourier transform-ion cyclotron resonance-mass spectrometry was also employed to confirm the identity of the detected lipids. We demonstrated higher incorporation of oleic acid in phosphatidylcholine and triacylglycerol composition, higher relative abundance of arachidonic acid containing phosphatidylinositol, and overall distinct free fatty acid profile in the livers of genetic hypertriglyceridemic mice. We propose that these alterations in liver lipid composition are related to the higher tissue and body metabolic rates described in these hypertriglyceridemic mice.

Easy Ambient Sonic-Spray Ionization Mass Spectrometric of Olive Oils: Quality Control and Certification of Geographical Origin

Herein, we show that easy ambient sonic spray ionization mass spectrometry in the negative ion mode [EASI(-)-MS] of water:methanol extracts of olive oil samples from 5 different countries (Portugal, Italy, Spain, Lebanon, and Greece) provides very characteristic profiles of chemotaxonomic markers, that is, free fatty acids and phenols. These EASI(-)-MS fingerprints, acquired with great speed and simplicity after minimal sample preparation, permits secure identification of the samples as olive oils via their unique profiles of fatty acids plus phenolic constituents as well the certification of geographical regions via characteristic features of the profiles of phenolic constituents.

Chemical profile of meta-chlorophenylpiperazine (m-CPP) in ecstasy tablets by easy ambient sonic-spray ionization, X-ray fluorescence, ion mobility mass spectrometry and NMR

Meta-chlorophenylpiperazine (m-CPP) is a new illicit drug that has been sold as ecstasy tablets. Easy ambient sonic-spray ionization mass spectrometry (EASI-MS) and X-ray fluorescence spectrometry (XRF) are shown to provide relatively simple and selective screening tools to distinguish m-CPP tablets from tablets containing amphetamines (mainly 3,4-methylenedioxymethamphetamine (MDMA)). EASI-MS detects the active ingredients in their protonated forms: [m-CPP + H](+) of m/z 197, [MDMA + H](+) of m/z 194, and [2MDMA + HCl + H](+) of m/z 423 and other ions from excipients directly on the tablet surface, providing distinct chemical fingerprints. XRF identifies Cl, K, Ca, Fe, and Cu as inorganic ingredients present in the m-CPP tablets. In contrast, higher Cl concentrations and a more diverse set of elements (P, Cl, Ca, Fe, Cu, Zn, Pt, V, Hf, Ti, Pt, and Zr) were found in MDMA tablets. Principal component analysis applied to XRF data arranged samples in three groups: m-CPP tablets (four samples), MDMA tablets (twenty three samples), and tablets with no active ingredients (three samples). The EASI-MS and XRF techniques were also evaluated to quantify m-CPP in ecstasy tablets, with concentrations ranging from 4 to 40 mg of m-CPP per tablets. The m-CPP could only be differentiated from its isomers (o-CPP and for the three isomers p-CPP) by traveling wave ion mobility mass spectrometry and NMR measurements.

Química forense: perspectivas sobre novos métodos analíticos aplicados à documentoscopia, balística e drogas de abuso

In this review recent methods developed and applied to solve criminal occurences related to documentoscopy, ballistic and drugs of abuse are discussed. In documentoscopy, aging of ink writings, the sequence of line crossings and counterfeiting of documents are aspects to be solved with reproducible, fast and non-destructive methods. In ballistic, the industries are currently producing ''lead-free'' or ''nontoxic'' handgun ammunitions, so new methods of gunshot residues characterization are being presented. For drugs analysis, easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is shown to provide a relatively simple and selective screening tool to distinguish m-CPP and amphetamines (MDMA) tablets, cocaine and LSD.

Analysis of Cocaine and Crack Cocaine via Thin Layer Chromatography Coupled to Easy Ambient Sonic-Spray Ionization Mass Spectrometry

Cocaine and crack cocaine are usually seized with a great diversity of adulterants, such as benzocaine, lidocaine, caffeine, and procaine. The forensic identification of cocaine in these drug mixtures is normally performed using colorimetric testing kits, but these tests may suffer from interferences providing false-positive or false-negatives. In this work, we describe the use of thin layer chromatography coupled to easy sonic-spray ambient ionization mass spectrometry (TLC/EASI-MS) for rapid and secure analysis of cocaine and crack cocaine. Fifteen cocaine samples were analyzed, and all of them revealed positive TLC/EASI-MS results for cocaine, but other drugs and adulterants were also detected such as lidocaine, caffeine, benzocaine, lactose, benzoylecgonine, and ecgonidine. False positives and false negatives, as judged by the TLC Rf values, were identified via on-spot characterization by EASI-MS. The TLC/EASI-MS combination seems therefore to provide an appropriate technique for secure forensic investigations of illicit drugs.

A Highly Effective Antioxidant and Artificial Marker for Biodiesel

Biodiesel is composed of saturated and unsaturated methyl esters of fatty acids formed via transesterification of vegetable oil or animal fat. This chemical nature makes biodiesel much more susceptible to oxidation or autoxidation during long-term storage than conventional petrodiesel. Increasing resistance to oxidation therefore requires the use of antioxidants. This paper investigates the effectiveness of the N,N′-di-sec-butyl-p-phenylenediamine (1) as a antioxidant to improve the oxidative stability of soybean, sunflower and canola biodiesel. Results indicate that the induction period for oxidation of soybean and canola biodiesel is significantly improved with the addition of only 0.2 ppm of the 1, reaching the oxidative stability specification (6 h by the Rancimat test). For sunflower biodiesel, 2.0 ppm of the 1 was necessary. This additive is also shown to be efficiently detected by the easy ambient sonic-spray ionization mass spectrometry technique, indicating that 1 and its analogues and derivative...

Real‐time monitoring of the progress of polymerization reactions directly on surfaces at open atmosphere by ambient mass spectrometry

The progress of an on-surface polymerization process involving alkyl and perfluoroalkyl silanes and siloxanes was monitored in real-time via easy ambient sonic spray ionization mass spectrometry (EASI-MS). When sprayed on surfaces, the organosilicon compounds present in commercially available nanofilm products (NFPs) react by condensation to form a polymeric coating. A NFP for coating of floor materials (NFP-1) and a second NFP for coating tiles and ceramics (NFP-2) were applied to glass, filter paper or cotton surfaces and the progress of the polymerization was monitored by slowly scanning the surface. Via EASI(+)-MS monitoring, significant changes in the composition of hydrolysates and condensates of 1H,1H,2H,2H-perfluorooctyl triisopropoxysilane (NFP-1) and hexadecyl triethoxysilane (NFP-2) were observed over time. The abundances of the hydrolyzed species decreased compared with those of the non-hydrolysed species for both NFP-1 and NFP-2 and the heavier oligomers became relatively more abundant over a period of 15-20 min. A similar tendency favouring the heavier oligomers was observed via EASI(-)-MS. This work illustrates the potential of ambient mass spectrometry for the direct monitoring of polymerization reactions on surfaces.

Petroleomics by EASI(±) FT-ICR MS

An ambient ionization/desorption technique, namely, easy ambient sonic-spray ionization mass spectrometry (EASI), has been applied to crude oil samples. From a single droplet of the sample placed on an inert surface, EASI(+/-) is shown to promote efficient desorption and ionization of a myriad of polar components via the action of its cloud of very minute supersonic bipolar charged droplets. The gaseous [M + H](+) and [M - H](-) ions concurrently formed by EASI(+/-) were analyzed by Fourier transform mass spectrometry (FT-ICR MS), and a total of approximately 6000 acidic and basic components have been attributed. EASI(+/-) FT-ICR MS of crude oils is show to be almost as fast as ESI(+)/ESI(-) FT-ICR MS, providing similar compositional information of polar components and spectral quality comparable to that of a commercial nonochip-based robotic ESI device. EASI(+/-) requires no sample workup thus eliminating risks of contamination during sample manipulation and memory effects because of carry over in pumping ESI lines. More importantly, EASI(+/-) is a voltage-free ionization technique therefore eliminating risks of redox processes or duality of ionization mechanisms that can be observed in voltage-assisted processes. Data visualization via typical petroleomic plots confirms the similarity of the compositional information provided by EASI(+/-) compared to ESI(+)/ESI(-). The ambient EASI(+/-) FT-ICR MS method requires no voltage switching in changing the ion polarity mode, offering a workup, heating and voltage-free protocol for petroleomic studies performed at open atmosphere directly on the undisturbed crude oil sample.

Molecularly imprinted polymers as analyte sequesters and selective surfaces for easy ambient sonic-spray ionization

The use of a molecularly imprinted polymer (MIP) as a selective surface for ambient mass spectrometry is demonstrated. The MIP is used to sequester target analytes from urine and easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is shown to be able to efficiently desorb the analytes from the MIP surface and then transfer them in protonated forms to the gas phase for MS analysis. A set of five phenothiazines (chlorpromazine, perphenazine, triflupromazine, thioridazine and prochlorperazine) were chosen from a proof-of-principle class of drug samples. A chlorpromazine-imprinted methacrylic polymer was synthesized and used to prepare a MIP probe. The MIP-EASI-MS technique using acidified methanol as solvent has been shown to allow quantification of all five drugs in urine with LOQ of ca. 1 micromol L(-1).

Fingerprinting and aging of ink by easy ambient sonic-spray ionization mass spectrometry

Using easy ambient sonic-spray ionization mass spectrometry (EASI-MS), fast and non-destructive fingerprinting identification and aging of ballpoint pen ink writings have been performed directly from paper surfaces under ordinary ambient conditions. EASI-MS data obtained directly from the ink lines showed that pens from different brands provide typical ink chemical profiles. Accelerated ink aging has also been monitored by EASI-MS revealing contrasting degradation behaviors for six different common ink dyes. As demonstrated for Basic Violet 3, some dyes display a cascade of degradation products whose abundances increase linearly with time thus functioning as 'chemical clocks' for ink aging. Analysis of questionable documents has confirmed the ink aging capabilities of EASI-MS. The order of superimposition at a crossing point has also been determined by EASI-MS. For two superimposed ink lines, continuous EASI-MS analysis has also shown that the EASI spray is able to penetrate through the layers and therefore both ink layers could be characterized.

Instantaneous characterization of vegetable oils via TAG and FFA profiles by easy ambient sonic-spray ionization mass spectrometry

A fast and reliable method is presented for the analysis of vegetable oils. Easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is shown to efficiently desorb and ionize the main oil constituents from an inert surface under ambient conditions and to provide comprehensive triacylglyceride (TAG) and free fatty acid (FFA) profiles detected mainly as either [TAG + Na](+) or [FFA-H](-) ions. EASI(+/-)-MS analysis is simple, easily implemented, requires just a tiny droplet of the oil and is performed without any pre-separation or chemical manipulation. It also causes no fragmentation of TAG ions hence diacylglyceride (DAG) and monoacylglyceride (MAG) profiles and contents can also be measured. The EASI(+/-)-MS profiles of TAG and FFA permit authentication and quality control and can be used, for instance, to access levels of adulteration, acidity, oxidation or hydrolysis of vegetable oils in general.

Fingerprinting of propolis by easy ambient sonic-spray ionization mass spectrometry

Chemical profiles of a representative set of 49 propolis ethanolic extracts collected worldwide (North and South America, Europe, Asia and Oceania) were obtained via easy ambient sonic-spray ionization mass spectrometry (EASI-MS). This simple and easily implemented fingerprinting technique analyses directly (without any pre-separation or sample manipulation) a tiny droplet of the ethanolic extract placed on a inert surface under ambient conditions. Data acquisition took about a minute per sample with no substantial sample carry-over. Extraction of propolis with ethanol by using an ultrasonic bath method gave EASI-MS data similar to the traditional maceration method, reducing total analysis time for the crude propolis resin from a week to just ca 1h. Principal component analysis of the EASI-MS data is shown to group samples according to the plant sources of their resins, which characterizes their geographical origin.

Fabric softeners: nearly instantaneous characterization and quality control of cationic surfactants by easy ambient sonic‐spray ionization mass spectrometry

A tiny droplet of typical samples of fabric softeners from different commercial brands placed on a smooth paper surface was subjected to easy ambient sonic-spray ionization mass spectrometry (EASI-MS). With no need for sample-preparation or pre-separation procedures, EASI-MS and EASI-MS/MS identify nearly instantaneously the main surfactants and the homologous series employed in their formulations. Adulterated and low quality samples containing no or less efficient softeners are also easily recognized.

Analysis of biodiesel and biodiesel–petrodiesel blends by high performance thin layer chromatography combined with easy ambient sonic-spray ionization mass spectrometry

High performance thin layer chromatography (HPTLC) combined with on-spot detection and characterization via easy ambient sonic-spray ionization mass spectrometry (EASI-MS) is applied to the analysis of biodiesel (B100) and biodiesel-petrodiesel blends (BX). HPTLC provides chromatographic resolution of major components whereas EASI-MS allows on-spot characterization performed directly on the HPTLC surface at ambient conditions. Constituents (M) are detected by EASI-MS in a one component-one ion fashion as either [M + Na](+) or [M + H](+). For both B100 and BX samples, typical profiles of fatty acid methyl esters (FAME) detected as [FAME + Na](+) ions allow biodiesel typification. The spectrum of the petrodiesel spot displays a homologous series of protonated alkyl pyridines which are characteristic for petrofuels (natural markers). The spectrum for residual or admixture oil spots is characterized by sodiated triglycerides [TAG + Na](+). The application of HPTLC to analyze B100 and BX samples and its combination with EASI-MS for on-spot characterization and quality control is demonstrated.

Single-Shot Biodiesel Analysis: Nearly Instantaneous Typification and Quality Control Solely by Ambient Mass Spectrometry

Using a simple and easily implemented desorption/ionization mass spectrometry technique, a tiny droplet of biodiesel placed on the surface of a sheet of paper is analyzed directly and nearly instantaneously under ambient conditions. No pre-separation or sample preparation is required, and clean mass spectra are obtained with great simplicity. In the positive ion mode, easy ambient sonic-spray ionization mass spectrometry, EASI(+)-MS, provides typical profiles of the major components of biodiesel samples, that is, either methyl esters (FAME) or ethyl esters (FAEE) of the natural fatty acids and triglycerides (TAG) from residual oil or oil from adulteration. Each FAME (FAEE) or TAG molecule is detected as a single sodiated molecule, [M + Na] (+) with relative intensities that correlate well with the known fatty acid profiles of the oil. Using EASI(-)-MS, typical and complementary profiles of free fatty acids (FFA) are obtained, which are detected in their deprotonated forms [FAA - H] (-). A general, single-shot approach for biodiesel analysis is therefore described, and samples from different feedstocks, from blends with petrodiesel, or from either methanol or ethanol trans-esterification are readily typified and major parameters of quality accessed.

Easy Ambient Sonic-Spray Ionization Mass Spectrometry Combined with Thin-Layer Chromatography

On-spot detection and analyte characterization on thin-layer chromatography (TLC) plates is performed via ambient desorption/ionization and (tandem) mass spectrometry detection, that is, via easy ambient sonic spray ionization mass spectrometry (EASI-MS). As proof-of-principle cases, mixtures of semipolar nitrogenated compounds as well as pharmaceutical drugs and vegetable oils have been tested. The technique has also been applied to monitor a chemical reaction of synthetic importance. EASI is the simplest and gentlest ambient ionization technique currently available, assisted solely by N2 (or air). It uses no voltages, no electrical discharges; no UV or laser beams, and no high temperature and is most easily implemented in all API mass spectrometers. TLC is also the simplest, fastest, and most easily performed chromatographic technique. TLC plus EASI-MS therefore provide a simple and advantageous combination of chromatographic separation and sensitive detection of the TLC spots as well as on-spot MS or MS/MS characterization. The favorable characteristics of TLC-EASI-MS indicate advantageous applications in several areas such as drug and oil analysis, phytochemistry and synthetic chemistry, forensics via reliable counterfeit detection, and quality control.

Easy Ambient Sonic-Spray Ionization-Membrane Interface Mass Spectrometry for Direct Analysis of Solution Constituents

Using a cellulose dialysis membrane and aqueous solutions of common drugs as a proof-of-principle example, we demonstrate that solid but permeable and flexible membranes can be used as interfaces for the direct analysis of solution constituents via easy ambient sonic-spray ionization mass spectrometry. This new combination of MS techniques, herein termed EASI-MIMS, promotes droplet pick up of the analyte from the external surface of the membrane from where the analyte has selectively permeated for proper mass spectrometry characterization and quantitation. Possible application of EASI-MIMS such as the environmental analyses of effluents, on-line monitoring of fermentation and biotransformations and on-line pharmacokinetic blood analysis are discussed.