Ambient Pollution Research Articles

Global burden of adolescent and young adult cardiovascular diseases and risk factors: Results from Global Burden of Disease Study 2019

<p>Comprehensive research on the global burden of CVDs among adolescents and young adults (15-44 years) is lacking. We analyzed the results from the Global Burden of Disease (GBD), Injuries, and Risk Factors Study 2019, and the incidence, mortality, and disability-adjusted life-years (DALYs) of 13 CVD types in adolescents and young adults were calculated. We also assessed 19 risk factors associated with CVD-related DALYs across 204 countries and territories from 1990-2019. In 2019, there were 5.7 million CVD incidents and 45.4 million DALYs and 761,458 deaths due to CVDs in adolescents and young adults, globally. CVDs remained the first leading cause of death worldwide among 21 causes of death and the fifth leading cause of death and disability combined in 2019. From 1990-2019, the absolute number of CVD incidents and CVD-related deaths and DALYs increased by 45.5%, 21.6%, and 18.0%, respectively. The highest age-standardized DALY, incidence, and mortality rates from CVDs were observed in the low- and low-middle-sociodemographic index (SDI) regions. Ischemic heart disease, stroke, and rheumatic heart disease were the top three CVDs with the highest age-standardized DALYs. The five leading specific risk factors contributing to CVD-related DALYs were high systolic blood pressure, high low-density lipoprotein (LDL) cholesterol, high body mass index (BMI), ambient particulate matter pollution (PM2.5), and smoking. The burden of CVDs in adolescents and young adults increased substantially from 1990-2019. Effective and targeted strategies for the prevention and management of CVDs in this population are needed to reduce the overall CVD burden.</p>

Investigating neighbourhood environmental risk factors associated with childhood acute respiratory infection symptoms in Ethiopia mixed effect and multilevel logistic regression analysis based on EDHS 2016.

Acute respiratory infection is an infectious illness caused by acute viral or bacterial infection. According to a 2018 WHO report, exposures to indoor and ambient air environmental pollution were contributing factors to a higher risk of respiratory problems following 7 million deaths of children under five globally. Housing conditions such as wall material, roof type, kitchen location, sanitation condition, and cooking fuel type are household-level predictors of acute respiratory disease among children under five years of age. This research used EDHS-2016 secondary data, which are nationally representative. The data collection period was from January 18, 2016, to June 27, 2016. Among the 16,650 total surveys, 10,006 households that had children below 5 years of age. The outcome variable for this study was acute respiratory infection symptoms. Analyses were performed using STATA Version 17.1. The data were weighted before performing analysis to reinstate the representativeness of the sample. In the bivariable analysis, a p value <0.2 was used to screen for multivariable. Multicollinearity was checked using the variance inflation factor. Then, a multilevel multivariable regression model was used in this study for the analysis of acute respiratory infection symptoms and possible predictor variables. Variables with a p value <0.05 in multivariable regression analysis were considered statistically significant predictors. Most (95.00%) households commonly used solid fuel for cooking, and household main construction materials: 81.44 and 91.03% of floors and walls of households were constructed with unprocessed natural materials, respectively. The prevalence of acute respiratory infection symptoms among children under five years of age was 7.955% (7.397, 8.551%). The findings indicated that acute respiratory infection symptoms among children under five years of age were significantly linked with the age of the children, diarrhea status, residence, region, fuel type, stool disposal, wall material, and floor material. Interventions should target modifiable factors such as proper stool disposal of the youngest child, informing the health effects of poor housing conditions such as improving wall and floor construction material to reduce acute respiratory infection symptoms among children under five years of age.

Spatial analysis of ambient heavy metal pollutants in the tree leaves in Kanchipuram town, Tamil Nadu, India

Spatial distribution and accumulation of nine harmful heavy metals (Pb, Zn, Mn, Fe, Cr, Cu, Cd, As and Al) on the leaf surfaces of five tree species namely Saraca asoca, Ficus religiosa, Syzygium cumini, Pongamia glabra and Terminalia catappa were analysed to identify the level of contamination of ambient air in Kanchipuram town, TamilNadu. The leaf samples were collected during February-March 2018 from six sites located within the town in the distributed manner and analysed by using inductively coupled plasma mass spectrometry. The results revealed that the concentration of As, Cd, Cr and Pb were invariably found lesser than their detectable limit, Fe (289mg/kg), Al (162mg/kg) was identified to be maximized, Cu, Mn and Zn lower levels. The absorption capacity of Ficus religiosa was poor and other species were shown good responses. The concentrations of Al, Cu, Fe, Mn and Zn were very low in sites 1, 2, 3, 6 where the trees were numerous and found high at sites 4 and 5 may be due to anthropogenic activities and vehicular emission. According to the analysis, the selected species performed as bio indicators and were developed around the industries to maintain greenbelts and enhance air quality.

Mixed-valence Cu-based heterostructures for efficient electrochemical nitrate reduction to ammonia.

The electrocatalytic NO3- reduction reaction (NO3RR) to NH3 provides a promising pathway for ambient NH3 synthesis and environmental pollution treatment. Cu and its oxides are recognized as effective NO3RR electrocatalysts due to their favorable d-orbital energy levels and superior kinetics. In this work, mixed-valence Cu-based catalysts with tunable valence states were constructed via an inorganic salt-induced MOF-derived strategy. Notably, optimized Cu-CuxO/C-0.3 featured a Cu/Cu2O heterostructure and demonstrated the lowest Cu valence state. The resulting Cu/Cu2O heterointerface facilitated electron transfer and increased the density of electrochemically active sites, leading to an enhanced faradaic efficiency of 81.4% and a remarkable yield rate of 13.38 mg h-1 cm-2 (ca. 2.39 mol h-1 gcat.-1) at -0.8 V vs. RHE. This work presents insights for designing multi-phase heterostructured NO3RR catalysts and emphasizes their potential significance in efficient ammonia production.

Measuring the air pollution benefits of public transport projects

We discuss two approaches to estimating the air quality impacts of public transit projects, focusing on Metro projects in the context of developing countries: air quality modeling and reduced-form econometric methods. As we illustrate, pollution reductions due to Metro projects implied by pollutant chemistry, vehicle emissions factors, and modal shifts may differ from econometric estimates of the impact of transit projects on ambient pollution concentrations. We discuss both approaches and illustrate how economics researchers can use estimated emissions reductions associated with a transit project and pollutant chemistry as a check on their estimates of changes in ambient concentrations.

Impact of antioxidants on PM2.5 oxidative potential, radical level, and cytotoxicity

Antioxidants are typically seen as agents that mitigate environmental health risks due to their ability to scavenge free radicals. However, our research presents a paradox where these molecules, particularly those within lung fluid, act as prooxidants in the presence of airborne particulate matter (PM2.5), thus enhancing PM2.5 oxidative potential (OP). In our study, we examined a range of antioxidants found in the respiratory system (e.g., vitamin C, glutathione (GSH), and N-acetylcysteine (NAC)), in plasma (vitamin A, vitamin E, and β-carotene), and in food (tert-butylhydroquinone (TBHQ)). We aimed to explore antioxidants' prooxidant and antioxidant interactions with PM2.5 and the resulting OP and cytotoxicity. We employed OH generation assays and electron paramagnetic resonance assays to assess the pro-oxidative and anti-oxidative effects of antioxidants. Additionally, we assessed cytotoxicity interaction using a Chinese hamster ovary cell cytotoxicity assay. Our findings revealed that, in the presence of PM2.5, all antioxidants except vitamin E significantly increased the PM2.5 OP by generating more OH radicals (OH generation rate: 0.16–24.67 pmol·min−1·m−3). However, it's noteworthy that these generated OH radicals were at least partially neutralized by the antioxidants themselves. Among the pro-oxidative antioxidants, vitamin A, β-carotene, and TBHQ showed the least ability to quench these radicals, consistent with their observed impact in enhancing PM2.5 cytotoxicity (PM2.5 LC50 reduced to 91.2 %, 88.8 %, and 75.1 % of PM2.5's original level, respectively). Notably, vitamin A and TBHQ-enhanced PM2.5 OP were strongly associated with the presence of metals and organic compounds, particularly with copper (Cu) contributing significantly (35 %) to TBHQ's pro-oxidative effect. Our study underscores the potential health risks associated with the interaction between antioxidants and ambient pollutants.

Thermocatalytic oxidation of a binary mixture of formaldehyde and toluene at ambient levels by a titanium dioxide supported platinum catalyst

The thermocatalytic oxidative potential of various supported noble metal catalysts (SNMCs) is well-known for hazardous volatile organic compounds (VOCs), e.g., formaldehyde (FA) and toluene. However, little is known about SNMC performance against ambient VOC pollution with low concentration (subppm levels) relative to industrial effuluents with high concentrations (several hundred ppm). Here, the thermocatalytic oxidation performance of a titanium dioxide (TiO2)-supported platinum catalyst (Pt/TiO2) has been evaluated for a low-concentration binary mixture of FA and toluene at low temperatures and in the dark. A sample of TiO2 containing 1 wt% Pt with thermal reduction pre-treatment under hydrogen achieved 100 % conversion of FA (500 ppb) and toluene (100 ppb) at 130 °C and a gas hourly velocity of 59,701 h−1. Its catalytic activity was lowered by either a decrease in catalyst mass or an increase in VOC concentration, relative humidity, or flow rate. In situ diffuse reflectance infrared Fourier transform spectroscopy, density functional theory simulations, and molecular oxygen (O2) temperature–programmed desorption experiments were used to identify possible VOC oxidation pathways, reaction mechanisms, and associated surface phenomena. The present work is expected to offer insights into the utility of metal oxide-supported Pt catalysts for the low-temperature oxidative removal of gaseous VOCs in the dark, primarily for indoor air quality management.

Associations of long-term exposure to air pollution and physical activity with the risk of systemic inflammation-induced multimorbidity in Chinese adults: results from the China multi-ethnic cohort study (CMEC)

ObjectivePrevious studies proved the effect of long-term exposure to air pollution or physical activity (PA) on the risk of systemic inflammation-induced multimorbidity (SIIM), while the evidence regarding their joint effects was rare, especially in low- and middle-income countries. Therefore, we aimed to examine the extent of interaction or joint relations of PA and air pollution with SIIM.MethodsThis study included 72,172 participants from China Multi-Ethnic Cohort.The average concentrations of ambient particulate matter pollutants (PM1, PM2.5, and PM10) were estimated using satellite-based random forest models. Self-reported information on a range of physical activities related to occupation, housework, commuting, and leisure activities was collected by an interviewer-administered questionnaire. A total of 11 chronic inflammatory systemic diseases were assessed based on self-reported lifetime diagnosis or medical examinations. SIIM was defined as having ≥ 2 chronic diseases related to systemic inflammation. Logistic regression models were used to assess the complex associations of air pollution particulate matter and PA with SIIM.ResultsWe found positive associations between long-term air pollution particulates exposure and SIIM, with odds ratios (95%CI) of 1.07 (1.03 to 1.11), 1.18 (1.13 to 1.24), and 1.08 (1.05 to 1.12) per 10 µg/m3 increase in PM1, PM2.5, and PM10. No significant multiplicative interaction was found between ambient air pollutant exposure and PA on SIIM, whereas negative additive interaction was observed between long-term exposure to PM2.5 and PA on SIIM. The positive associations between low volume PA and SIIM were stronger among those exposed to high-level air pollution particulates. Compared with individuals engaged in high volume PA and exposed to low-level ambient air pollutants, those engaged in low volume PA and exposed to high-level ambient air pollutants had a higher risk of SIIM (OR = 1.49 in PM1 exposure, OR = 1.84 in PM2.5 exposure, OR = 1.19 in PM10 exposure).ConclusionsLong-term (3 years average) exposure to PM1, PM2.5, and PM10 was associated with an increased risk of SIIM. The associations were modified by PA, highlighting PA’s importance in reducing SIIM for all people, especially those living in high-level air pollution regions.

Different VOC species derived from fugitive emissions at various altitudes around petrochemical plant

Volatile organic compounds (VOCs) emitted from fugitive sources are crucial for environmental and health risk assessments. However, monitoring these emissions at ground level, according to traditional technical specifications, has made it challenging to identify polluted air masses and collect purposeful samples. In this study, we focused on utilizing an unmanned aerial vehicle system to obtain air samples around a petrochemical industrial park. We conducted a quantitative analysis of 108 VOC species and compared the results between aerial and ground-level samples. The findings indicated a higher presence of reactive compounds in the aerial samples. The sample pairs exhibited relatively homogeneous compositions of hydrocarbons with fewer than eight carbon atoms, suggesting a well-mixed condition for light compounds. Conversely, the aerial samples exclusively exhibited high mixing ratios of C8–C15 compounds, including branched paraffins and aldehydes. Based on the quantified VOCs, we evaluated the ozone formation potential (OFP) and secondary organic aerosol formation potential (SOAP). The results highlighted aldehydes, alkenes, and aromatics, particularly propanal, 2-butene, m/p-xylene, and benzaldehyde, as priority control compounds. Additionally, the semiquantitative concentrations of these non-quantitative C8–C15 species ranged from 1 to 15 ppbv, with a total content exceeding 150 ppbv, it indicated the significant contribution to ambient secondary pollution. These results provide valuable insights into the identification of potential emission sources and the assessment of environmental repercussions attributed to these intermediate-volatile organic compounds from fugitive emissions around petrochemical plant.

Ambient ozone pollution impairs glucose homeostasis and contributes to renal function decline: Population-based evidence

Particulate matter pollution could increase the risk of kidney disease, while evidence for ozone exposure is less well-established. Here, we aimed to evaluate the effect of ozone pollution on renal function and explore mechanisms. We first conducted a cross-sectional study based on Wuhan Chronic Disease Cohort Study baseline information. We recruited 2699 eligible participants, estimated their residential ozone concentrations, collected fasting peripheral blood samples for biochemical analysis and calculated the estimated glomerular filtration rate (eGFR). The linear regression model was applied to evaluate the long-term association between ozone pollution and eGFR. Then, we recruited another 70 volunteers as a panel with 8 rounds follow-up visits. We calculated the eGFR and measured fasting blood glucose and lipid levels. The linear mixed-effect model along with mediation analysis were performed to confirm the short-term association and explore potential mechanisms, respectively. For the long-term association, a 10.95 μg/m3 increment of 3-year ozone exposure was associated with 2.96 mL/min/1.73 m2 decrease in eGFR (95%CI: −4.85, −1.06). Furthermore, the drinkers exhibited a pronounced declination of eGFR (−7.46 mL/min/1.73 m2, 95%CI: −11.84, −3.08) compared to non-drinkers in relation to ozone exposure. Additionally, a 19.02 μg/m3 increase in 3-day ozone concentrations was related to 2.51 mL/min/1.73 m2 decrease in eGFR (95%CI: −3.78, −1.26). Hyperglycemia and insulin resistance mediated 12.2% and 16.5% of the aforementioned association, respectively. Our findings indicated that higher ozone pollution could affect renal function, and the hyperglycemia and insulin resistance linked to ozone might be the underlying mechanisms.

NH3 absorption line study and application near 1084.6 cm−1

Ammonia (NH3) holds significant importance as an industrial product, ambient trace pollutant, and a promising zero-carbon energy carrier, underscoring the critical need for accurate quantification in various applications. In this study, a mid-infrared quantum cascade laser (Mid-IR QCL) based tunable diode laser absorption spectroscopy (TDLAS) spectrometer was developed. It was coupled with two reactors, namely a gas cell and a shock tube and operated in three modes: low- and high-frequency (140 Hz and 10 kHz) scan modes and fixed-wavelength mode, tailored to the specific needs of each experimental scenario. The primary objects were NH3 line parameters measurement and absolute NH3 quantification. With the 140 Hz low-frequency scan mode, NH3-Ar pressure broadening coefficients of six transition lines near 1084.6 cm−1 were measured in a gas cell at 295 K and 1–11 mbar for the first time. These coefficients were subsequently employed to quantify the initial NH3 mole fraction in shock tube experiments, considering the substantial adsorption effect of NH3. Using the high-frequency scan mode (10 kHz), spectrally resolved NH3 absorption cross-sections were obtained in a shock tube across a pressure range of 1.46–3.25 bar and a temperature range of 1000–1800 K. This data, acquired for the first time, significantly contributes to the understanding of NH3 behavior in high-temperature environments. Additionally, potential interference from high-temperature water absorption near 1084.6 cm−1 was thoroughly examined. The high-temperature water absorption cross-section was measured over a pressure range of 0.99–3.02 bar and a temperature range of 1322–2905 K, utilizing a near-infrared water laser. Leveraging these comprehensive datasets, the study quantified the NH3 mole fraction during the NH3 oxidation process in the shock tube, employing the fixed-wavelength mode to achieve high time resolution. The quantified NH3 mole fraction was then compared to predictions from eleven recent chemical kinetic mechanisms, demonstrating the utility of the developed spectrometer in validating these mechanisms.

Ambient Ozone and Fine Particular Matter Pollution in a Megacity in South China: Trends, Concurrent Pollution, and Health Risk Assessment

Over the past several years, Shenzhen’s air quality has significantly improved despite increased ground-level ozone (O3) and the challenges in reducing fine particulate matter (PM2.5). We investigated concentration trends, concurrent pollution features, and long-term exposure health risks to enhance our understanding of the characteristics of O3 and PM2.5 pollution. From 2016 to 2022, there was a decrease in PM2.5 levels, but an increase in O3. Additionally, the premature mortality attributed to long-term air pollution exposure decreased by 20.1%. High-O3-and-PM2.5 days were defined as those when the MDA8 O3 ≥ 160 μg m–3 and PM2.5 ≥ 35 μg m–3. Significantly higher levels of O3, PM2.5, nitrogen dioxide (NO2), OX (OX = O3 + NO2), and sulfur dioxide (SO2) were observed on high-O3-and-PM2.5 days. Vehicle emissions were identified as the primary anthropogenic sources of volatile organic compounds (VOCs), contributing the most to VOCs (58.4 ± 1.3%), O3 formation (45.3 ± 0.6%), and PM2.5 formation (46.6 ± 0.4%). Cities in Guangdong Province around Shenzhen were identified as major potential source regions of O3 and PM2.5 during high-O3-and-PM2.5 days. These findings will be valuable in developing simultaneous pollution control strategies for PM2.5 and O3 in Shenzhen.

Indoor particulate matter concentrations and air cleaner intervention association with biomarkers in former smokers with COPD

BackgroundIndoor pollutants have been associated with worse clinical outcomes in chronic obstructive pulmonary disease (COPD). Elevated biomarkers are associated with ambient pollution exposure, however the association with indoor pollution remains unclear. MethodsFormer smokers with spirometry-confirmed COPD were randomized to portable air cleaner or placebo. Indoor particulate matter (PM2.5, PM10, and ultrafine particles [UFP; PM<0.1]) and biomarkers were measured longitudinally at pre-specified intervals and course PM fraction (PM10-2.5) was calculated. Biomarkers were categorized based on associations with biologic mechanisms: inflammation (white blood cell count, interleukin [IL]-6, IL-8, IL-1β, tumor necrosis factor-α, interferon-γ, serum amyloid A), platelet activation (P-selectin, CD40 ligand [CD40L], 11-dehdydro-thromboxane-B2 [11dTxB2]), endothelial dysfunction (Vascular Cell Adhesion Molecule [VCAM]-1, Intercellular Adhesion Molecule [ICAM]-1), and oxidative stress (thiobarbituric acid reactive substances [TBARS], 8-hydroxydeoxyguanosine, 8-isoprostane). Associations between PM concentrations and each biomarker were analyzed using multivariable linear mixed models. An intention-to-treat analysis was performed to evaluate the air cleaner intervention on the biomarker levels longitudinally. ResultsFifty-eight participants were randomized to each group. Finer PM was more strongly associated with higher IL-8 (mean difference per doubling: UFP 13.9% [p = 0.02], PM2.5 6.8% [p = 0.002], PM10-2.5 5.0% [p = 0.02]) while interferon-γ was associated with UFP and IL-1β with PM10-2.5. UFP and PM2.5 were associated with elevated levels of the oxidative stress biomarkers TBARS and 8-isoprostane respectively. For platelet activation markers, UFP was associated with higher 11dTxB2 while PM2.5 was associated with higher P-selectin and CD40L. Pollutants were not associated with biomarkers of endothelial dysfunction. In intention-to-treat analysis there was no association of the air cleaner intervention with any of the biomarkers. DiscussionAmong former smokers with COPD, elevated levels of indoor air pollutants, particularly ultrafine particles (PM<0.1), were associated with elevated biomarkers of inflammation, platelet activation, and oxidative stress. However, an air cleaner intervention that reduced PM did not significantly reduce biomarker levels.

Association of long-term ozone air pollution and age-related macular degeneration in older Chinese population

BackgroundAge-related macular degeneration (AMD) is the leading cause of legal blindness. It remains unclear whether and to what extent the ambient ozone pollution could increase the risk of AMD. MethodsA nationwide cross-sectional survey was conducted in 129 major cities in 27 of 31 provincial regions across China from 2018 to 2021. Data in relation to demographics, residential address, and medical histories were collected. The exposure-response relationship between ozone exposure and AMD was explored using the restricted cubic splines. A piecewise logistic regression model was used to examine the magnitudes of the association, after adjusting demographic, social-economic and co-pollutants. Residential ozone exposures were estimated using a satellite-based model. ResultsA total of 624,167 middle-aged and older participants were included in the final analyses, the overall prevalence of AMD was 16.76 %. The risk of AMD was consistently increasing with higher warm-season ozone concentration, and the risk became much larger after the cut-off of 110 μg/m3 (approximately 50 ppb). Every 10 μg/m3 increment in warm-season ozone concentration, the adjusted odds ratio (OR) for AMD were 1.15 (1.13, 1.16) and 1.66 (1.63, 1.69) when the warm-season ozone concentration was below or above 110 μg/m3, respectively. ConclusionThis large-scale nationwide study provides the first epidemiological evidence demonstrating significant associations between long-term residential ozone exposure and AMD prevalence. Based on our findings, in conjunction with WHO global air quality guidelines, we suggest that a warm-season ozone of 110 μg/m3 should be adopted for middle-aged and older populations to reduce the risk of AMD. Ongoing efforts to reduce ozone exposure in communities through improved air quality regulations and public education are essential for the improvement of public health.

Exploratory analysis of the contributing factors of stroke

Stroke is a medical condition that occurs when the blood supply to the brain is interrupted, which causes cell death. Previous studies have shown that the leading risk factors of stroke include elevated systolic blood pressure, poor diet, high body mass index, high fasting plasma glucose, ambient particulate matter pollution, smoking, high low-density lipoprotein, kidney dysfunction, alcohol use, and low physical activity. However, how these factors differentially contribute to the occurrence of stroke remains elusive. In this study, 5110 cases and 11 risk factors were investigated and machine learning models were built to predict the occurrence of stroke and the importance of each of the factors. It was found that the random forest model showed the best performance in predicting stroke and age, glucose level, and body mass index were the top three most important risk factors underlying stroke. These findings shed light on future research in the prevention and diagnosis of stroke.

Analysis of Flow Rate Distribution in Progressive Divider for Reciprocating Compressor Lubrication

Reciprocating compressors require a correct fluid delivery to each lubrication point. Lubricant defeat means higher component wear and damages, whereas lubricant excess leads to undesired contamination of the processed gas, energy waste and ambient pollution. Two main lubrication systems are used for reciprocating compressors, namely “Pump To Point” (PTP) and “Progressive Divider” (PD) systems. In the first one, there are as many pumps as lubrication points and on each pump unit it is possible to adjust the flow rate delivery. In the second one, a single pump delivers the lubricant to a volumetric flow divider, which provides the metered amount to each lubrication point. A Progressive Divider is modelled under lumped parameter approach, with the aim to highlight its sensitivity to the main operating parameters and to provide awareness about its available operating range. The model is built in Amesim environment and validated thanks to a specific experimental activity that allows to relate the distributed amounts to the lubrication points. The model allows to simulate the PD system under the typical conditions of reciprocating compressors, pointing out its sensitivity on the pressure unbalance among the lubrication points and on the fluid properties. The lumped parameter modelling of PD systems is found to provide reliable information on fluid distribution, effective for design and diagnose activities and for research and development in the field of hydraulic progressive dividers.

Temporal trends in disease burden and attributable risk factors for tracheal, bronchus, and lung cancer in Nepal, 1990–2019

BackgroundTracheal, bronchus, and lung (TBL) cancer is one of the most common cancers in Nepal. The aim of this study was to analyze the changing disease burden and risk factors for TBL cancer in Nepal from 1990 to 2019. MethodsTBL cancer burden data were obtained from the Global Burden of Disease Study 2019. A decomposition analysis was used to explore the impact of changes in population size, population age structure, age-specific prevalence, and disease severity on long-term trends of the TBL cancer burden in Nepal. ResultsIn 2019, TBL cancer resulted in the loss of 45.2 thousand (95% uncertainty interval [UI]: 32.3–59.2 thousand) disability-adjusted life years (DALYs) in Nepal, with the age-standardized incidence and prevalence rates increasing by 12.7% (95% UI: −21.0 to 63.9%) and 12.8% (95% UI: −21.1 to 62.0%), respectively, compared with 1990. The proportion of DALYs due to TBL cancer increased significantly among people aged 70 years and older from 1990 to 2019. However, the proportion of DALYs due to TBL cancer still dominated among males and females aged 50–69 years. Population growth, population aging, and increased age-specific prevalence led to an increased disease burden of TBL cancer, while disease severity led to a decreased burden. In 2019, smoking remained the major risk factor for TBL cancer in Nepal, while ambient particulate matter pollution exhibited the most significant rise. ConclusionsThe disease burden of TBL cancer in Nepal has continued to increase over the past three decades, and given the continuing population growth and aging process, TBL cancer is likely to have a considerable impact on health in Nepal in the future. There is a need to further establish effective TBL cancer prevention and control policies.

Application of roadside air purifiers in urban street canyons: A pilot-scale study in Hong Kong

The implementation of roadside air purifiers has emerged as an effective active control measure to alleviate air pollution in urban street canyons. However, technical questions raised under real conditions remain challenging. In this study, we conducted a pilot-scale investigation involving seven units of self-designed roadside air purifiers in an urban street canyon in Hong Kong. The air cleaning effects were quantified with an air quality sensor network after rigorous quality control. The removal efficiencies of Nitrogen dioxide (NO2), Fine suspended particulates (PM2.5), Carbon monoxide (CO), and Nitric oxide (NO) were determined by comparing with simultaneously measured ambient concentrations, with hourly average efficiencies of 14.0 %–16.9 %, 3.5–10.0 %, 11.9 %–18.7 %, and 19.2 %–44.9 %, respectively. Generally, the purification effects presented variations depending on the ambient pollutants' levels. Higher ambient concentrations of NO2, PM2.5, CO correlated with increased purification effects, while NO presented the opposite trend. The influence of interval distance combined with spatial distribution indicated the operation of purifiers will induce local NO2 attenuation even at an interval distance of four meters. Statistical analysis delivered evidence the air cleaning ability exhibited optimal performance when relative humidity level is ranged from 70 % to 90 %, aligning with the prevailing conditions in Hong Kong. Additionally, improved purification effects were observed at the downwind direction, and their performance was enhanced when the wind speed exceeded 2.5 m/s. Moreover, we estimated the operational lifetime of the air purifiers to be approximately 130 days, offering crucial information regarding the filter replacement cycle. This work serves as a pioneering case study, showcasing the feasibility and deployment considerations of roadside air purifiers in effectively controlling air pollution in urban environments.

Breathable and Stretchable Multifunctional Triboelectric Liquid‐Metal E‐Skin for Recovering Electromagnetic Pollution, Extracting Biomechanical Energy, and as Whole‐Body Epidermal Self‐Powered Sensors

AbstractOn‐skin electronics can be conformably deployed on body for health monitoring, assisted living, and human/computer interfaces. However, developing corresponding energy devices is a critical challenge. Herein, a permeable and stretchable multifunctional liquid‐metal electronic skin that can generate electricity by recovering ambient electromagnetic pollution (from surrounding electrical appliances) and biomechanical energy (from body movements) is presented for epidermal energy and self‐powered sensing applications. To the best of the authors' knowledge, this is the first demonstration that a breathable on‐skin device can convert ambient electromagnetic pollution into useful electricity. The device is constructed using two stretchable microfibrous films sandwiching self‐organized mesh‐like and wrinkled liquid‐metal that affords electricity via induced electrification (±9.3 V, ±1.7 µA; 60 Hz) and triboelectricity (205.6 V, ±2.3 µA; 4 Hz). Its applicability in powering electronic devices is demonstrated. Moreover, it can serve as an epidermal self‐powered sensor for continuously monitoring whole‐body physiological signals and motions of the eyelids, face, throat, chest, and limbs, thus demonstrating its potential to remotely collect clinical and biomechanical information. Finally, it is used as an interface in diverse system‐level applications. These results shed light on new directions in on‐skin energy and sensing, enabling to usher electronics toward untethered and diversified applications.

Ambient temperature NO2 removal by adsorption on robust DMOFs: Regulating water stability, acid stability, and NO2 capacity by methyl functionalization

Nitrogen dioxide (NO2) is a dominant contributor to air pollution and urgently needs to be abated. The catalysis-based deNOx technologies can efficiently remove NO2 at elevated temperatures but fail to effectively deal with ambient NO2 pollution. Selective adsorption by solid porous adsorbents, especially metal-organic frameworks (MOFs), emerges as a promising strategy for ambient NO2 removal. To overcome the biggest challenge in developing low-temperature NO2 adsorbents today – poor stability and thus the inferior cyclable capacity, especially in the presence of water vapor, here we investigated the functionalization of a series of DMOFs with nonpolar methyl (–CH3) groups to regulate their water stability and NO2 adsorption capacity. Among these isoreticular DMOFs, the tetramethyl (TM) functionalized one (Ni-TM DMOF) exhibited a two-fold and 60-times increase in NO2 adsorption capacity under dry (2.2 mmol/g) and wet (1.8 mmol/g) conditions, respectively, over its counterpart without the TM groups (Ni-BDC DMOF). Careful structural characterizations attributed the elevated NO2 adsorption performance of DMOFs to the improved hydrophobicity induced by methyl group decoration under the wet condition. The combination of column breakthrough experiment, in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) study, and density functional theory (DFT) calculations revealed the NO2 adsorption mechanism under both dry and wet conditions. This work affords not only promising adsorbents for ambient NO2 removal but also new knowledge to guide the design of porous MOFs as robust adsorbents for acid gases capture.