Ambient Ionization Research Articles

Nuclear spin ratios of deuterated ammonia in prestellar cores

Context. Molecules containing two or more hydrogen or deuterium atoms have different nuclear spin states which behave as separate chemical species. The relative abundances of these species can give clues to their origin. Formation on grains is believed to yield statistical spin ratios whereas gas-phase reactions are predicted to result in clear deviations from them. This is also true for ammonia and its deuterated forms NH2D, NHD2, and ND3. Aims. Here we aim to determine the ortho/para ratios of NH2D and NHD2 in dense, starless cores, where their formation is supposed to be dominated by gas-phase reactions. Methods. The Large APEX sub-Millimeter Array (LAsMA) multibeam receiver of the Atacama Pathfinder EXperiment (APEX) telescope was used to observe the prestellar cores H-MM1 and Oph D in Ophiuchus in the ground-state lines of ortho and para NH2D and NHD2. The fractional abundances of these molecules were derived employing three-dimensional radiative transfer modelling, using different assumptions about the abundance profiles as functions of density. We also ran gas-grain chemistry models with different scenarios concerning proton or deuteron exchanges and chemical desorption from grains to find out if one of these models can reproduce the observed spin ratios. Results. The observationally deduced ortho/para ratios of NH2D and NHD2 are in both cores within 10% of their statistical values 3 and 2, respectively, and taking 3 σ limits, deviations from these of about 20% are allowed. Of the chemistry models tested here, the model that assumes proton hop (as opposed to full scrambling) in reactions contributing to ammonia formation, and a constant efficiency of chemical desorption, comes nearest to the observed abundances and spin ratios. Conclusions. The nuclear spin ratios derived here are in contrast with spin-state chemistry models that assume full scrambling in proton donation and hydrogen abstraction reactions leading to deuterated ammonia. The efficiency of chemical desorption strongly influences the predicted abundances of NH3, NH2D, and NHD2, but has a lesser effect on their ortho/para ratios. For these the proton exchange scenario in the gas is decisive. We suggest that this is because of rapid re-processing of ammonia and related cations by gas-phase ion-molecule reactions.

Arc plasma for high-efficiency ionization and scavenging of plasticizers in wrap films

Herein, ambient electric arc ionization mass spectrometry was used to examine 16 plasticizers in various wrap films, demonstrating high sensitivity (detection limit: <0.2 ng/mg) and precision (intra-/inter-day precision: <12 %). The ease of operation helps in the identification of wrap film and plasticizer analysis. In addition, the introduction of a cold arc plasma treatment presents a practical and innovative method for effectively eliminating plasticizers. This innovative strategy has implications for both environmental protection and food safety.

Sample Injection for Real-Time Analysis (SIRTA) Using GC-MS with Cold EI.

There is a continual demand for advanced methods and instruments for real-time analysis (RTA). Most of the current RTA techniques based on MS involve ambient desorption ionization technology. However, flow injection of liquid extracted samples is another option without added modifications or cost to existing LC-MS instruments. In this work, we introduce a new RTA approach named sample injection for real-time analysis (SIRTA) using GC-MS with Cold EI. In SIRTA, the standard GC column is replaced with a 1 m long 0.1 mm I.D. fused silica capillary that connects the GC injector to the MS transfer-line of Cold EI. Thus, SIRTA with Cold EI imposes no need for any additional instrumentation; hence, it is characterized by zero added cost. Like in flow injection in MS of LC-MS, the sample is dissolved in ∼1 mL methanol or another solvent. Subsequently, the vial is placed in the GC-MS autosampler while using a standard syringe for injection without any GC separation. The analysis takes merely 0.2-0.7 min, ensuring rapid and consecutive analyses. Unlike standard EI, Cold EI enables SIRTA by taking advantage of its fly through open ion source to avoid overwhelming the ion source during the elution of solvents while still providing enhanced molecular ions for nearly all analytes. In this study, we demonstrated SIRTA Cold EI analysis of 12 compounds and 7 mixtures, including various prescription and illicit drugs, cannabis and petroleum samples, and other synthetic organic compounds including those with molecular weight up to 800 g/mol.

Emulsified oil fouling resistant cellulose acetate-MoS2-nanocomposite membrane for oily wastewater remediation

This study evaluated the performance stability of amphiphilic cellulose acetate-MoS2-nanocomposite membranes (CMN) on oil removal and flux, oil fouling trends, as well as MoS2's catalytic peroxidase-like efficiency for oily wastewater treatment. When H2O2 was present in the feed, the membrane consistently achieved oil removal rates as high as 83.12 %, with only <10 % flux decline over an 80-minute filtration. During longer-term filtration of 4–6 h, the CMN membrane also exhibited significantly lower overall flux decline rates compared to the neat membrane with flux decline rates of 16.27 %, which was half of the cellulose membrane flux of 39.38 %. The fouling resistant performance was underpinned by the generation of reactive oxygen species (ROS) via catalytic reactions of MoS2 and H2O2. Coumarin was use as ROS scavenging agent and confirmed that the ROS amount was affected by the MoS2 and H2O2 dosages. The CMN membrane achieved the oil removal to the permissible discharge limit for low concentration wastewater. As a low-pressure membrane, it offered advantages of less energy consumption and continuously operating mode without frequent chemical cleaning and desorption. These findings support the CMN membrane's potential as a promising solution for treating industrial oily wastewater.

Lewis Acidic Metal-Organic Framework Assisted Ambient Liquid Extraction Mass Spectrometry Imaging for Enhancing the Coverage of Poorly Ionizable Lipids in Brain Tissue.

The spatial distribution of lipidomes in tissues is of great importance in studies of living processes, diseases, and therapies. Mass spectrometry imaging (MSI) has become a critical technique for spatial lipidomics. However, MSI of low-abundance or poorly ionizable lipids is still challenging because of the ion suppression from high-abundance lipids. Here, a metal-organic framework (MOF) Zr6O4(OH)4(1,3,5-Tris(4-carboxyphenyl) benzene)2(triflate)6(Zr6OTf-BTB) was prepared and used for selective on-tissue adsorption of phospholipids to reduce ion suppression from them to poorly ionizable lipids. The results show that Zr6OTf-BTB with strong Lewis acidic sites and a large specific surface area (647.9 m2·g-1) could selectively adsorb phospholipids under 1% FA-MeOH. Adsorption efficiencies of phospholipids are 88.4-144.9 times higher than those of other neutral lipids. Moreover, the adsorption capacity and the adsorption kinetic rate constant of the new material to phospholipids are higher than those of Zr6-BTB (242.72 vs 73.96 mg·g-1, 0.0442 vs 0.0220 g·mg-1·min-1). A Zr6OTf-BTB sheet was prepared by a lamination technique for on-tissue phospholipid adsorption from brain tissue. Then, the tissue section on the Zr6OTf-BTB sheet was directly imaged via ambient liquid extraction-MSI with 1% FA-MeOH as the sampling solvent. The results showed that phospholipids could be 100% removed directly on tissue, and the detection coverage of the Zr6OTf-BTB-enhanced MSI method to ceramides (Cers) and hexosylceramides (HexCers) was increased by 5-26 times compared with direct tissue MSI (26 vs 1 and 17 vs 3). The new method provides an efficient and convenient way to eliminate the ion suppression from phospholipids in MSI, largely improving the detection coverage of low-abundance and poorly ionizable lipids.

Utilizing a Metal Inlet Coiled with Copper Wire as the Ion Source for Ambient Ionization Mass Spectrometry.

In ambient ionization mass spectrometry (MS), a customized metal inlet is typically adapted to the orifice of the mass spectrometer for ease of introduction of the sample. We herein explore that the metal inlet coiled with a copper wire (∼50 μm) can be directly used as an ion source to induce corona discharge-like processes for ionization of analytes in the gas phase. When the metal inlet is subjected to a high voltage in the mass spectrometer, the electric field provided by the mass spectrometer enables the generation of corona discharge to ionize volatile/semivolatile analytes derived from the sample in the condensed phase. The limit of detection for azulene derived from the aqueous sample was as low as ∼1 pM. Moreover, we also demonstrated the feasibility of coupling ultraviolet-visible absorption spectroscopy with MS by using the metal inlet coiled with a thin copper wire as the interface. Integration of these two techniques enables the simultaneous acquisition of spectra from both instruments for quantitative and qualitative analysis of the sample. Furthermore, we showed that polar and nonpolar analytes in a mixture can be acquired in the same mass spectrum by simply depositing a sample droplet (∼20 μL) on a dielectric substrate near the copper wire-coiled metal inlet of the mass spectrometer. The ionization processes involved both electrospray ionization and corona discharge. To demonstrate the applicability of our method for detecting nonpolar and polar analytes in complex samples, we spiked a nonpolar analyte, benzo[a]pyrene, to a spice sample and successfully detected analytes with different polarities using our approach.

Simultaneous Detection of Aldehyde Metabolites by Light-Assisted Ambient Ionization Mass Spectrometry.

In the clinic, small-molecule metabolites (SMMs) in blood are highly convincing indicators for disease diagnosis, such as cancer. However, challenges still exist for detection of SMMs due to their low concentration and complicated components in blood. In this work, we report the design of a novel "selenium signature" nanoprobe (Se nanoprobe) for efficient identification of multiple aldehyde metabolites in blood. This Se nanoprobe consists of magnetic nanoparticles that can enrich aldehyde metabolites from a complex environment, functionalized with photosensitive "selenium signature" hydrazide molecules that can react with aldehyde metabolites. Upon irradiation with UV, the aldehyde derivatives can be released from the Se nanoprobe and further sprayed by mass spectrometry through ambient ionization (AIMS). By quantifying the selenium isotope distribution (MS/MS) from the derivatization product, accurate detection of several aldehyde metabolites, including valeraldehyde (Val), heptaldehyde (Hep), 2-furaldehyde (2-Fur), 10-undecenal aldehyde (10-Und), and benzaldehyde (Ben), is realized. This strategy reveals a new solution for quick and accurate cancer diagnosis in the clinic.

Caffeine quantification in dietary supplements using high-throughput on-line solid phase extraction coupled to Venturi easy ambient sonic-spray ionization mass spectrometry.

Caffeine is present in a large number of beverages and is an additive used in dietary supplements. Therefore, the concern about its quality and safety for consumers has been increasing and hence requires faster and simpler analytical methods to determine the caffeine amount. The high-throughput analysis is an appropriate solution to pharmaceuticals, bioanalysis, forensic and food laboratory routines. In this sense, Venturi easy ambient sonic-spray ionization mass spectrometry (V-EASI-MS), a specific ambient ionization source, is suitable to enable direct analysis of sample solutions in real time and is appropriate to be coupled to liquid chromatography (LC). The development of an on-line solid phase extraction system coupled to V-EASI-MS optimizes the advantages of LC-MS hyphenation by enhancing the figures of merit of the analytical method according to AOAC guidelines and simultaneously minimizing the runtime analysis to 1.5 min per sample, as well as sample preparation steps and solvent consumption, which is currently a challenge for quantitative applications of ambient ionization MS.

Rapid detection of aflatoxin B1, zearalenone and ochratoxin A in grains by thermal desorption dielectric barrier discharge ionization mass spectrometry.

Dielectric barrier discharge ionization is increasingly used for rapid detection in ambient mass spectrometry, although more often for gaseous and highly volatile samples than for solids and liquids. In this project, we present a rapid and sensitive method for detecting mycotoxins and demonstrate its capability for the detection of aflatoxin B1, zearalenone, and ochratoxin A in food samples. Our method is based on thermal desorption coupled to dielectric barrier discharge ionization mass spectrometry (TD-DBDI-MS), which we show generates minimal interferences and produces almost exclusively molecular ions. We detected mycotoxins in various food samples, including corn, peanuts, millet, and rice. Our method has a linear dynamic range of 1 μg kg-1 to 100 μg kg-1 for all three mycotoxins and a limit of detection (LOD) of 0.31 μg kg-1, 0.28 μg kg-1 and 0.43 μg kg-1, respectively. It is simple, rapid, reduces the pretreatment steps and has significant potential for practical applications.

Trends in Biopharmaceutical Analysis: A Focus on Integrating Single-Cell Omics with Microfluidic Chips

Biopharmaceutical analysis is a rapidly evolving field that requires the development of new technologies and methods to keep pace with the increasing complexity of biologics. One of the most promising areas of research is the use of single-cell omics and microfluidic chips for the analysis of biopharmaceuticals. Single-cell omics has revolutionized our understanding of cellular heterogeneity, while microfluidic chips have enabled high-throughput analysis of single cells that provide an understanding of the complex biological network that complements the genomics and transcriptomics studies. This article will explore some of the emerging trends and technologies in biopharmaceutical analysis, with a particular focus on single-cell omics and microfluidic chips. We will also discuss the developments in ambient ionization mass spectrometry such as sub nanoampere ionization and the potential of low current ionization in studying cell-to-cell heterogeneity and its role in metabolomics.

Implications for new particle formation in air of the use of monoethanolamine in carbon capture and storage.

Alkanolamines are currently being deployed in carbon capture and storage (CCS) technology worldwide, and atmospheric emissions have been found to coincide with locations exhibiting elevated concentrations of methanesulfonic acid (MSA). It is thus critical to understand the fate and potential atmospheric reactions of these chemicals. This study reports the characterization of sub-10 nm nanoparticles produced through the acid-base reaction between gas phase monoethanolamine (MEA) and MSA, a product of organosulfur compound oxidation in air, using a flow reactor under dry and humid (up to ∼60% RH) conditions. Number size distribution measurements show that MEA is even more efficient than methylamine in forming nanoparticles on reaction with MSA. This is attributed to the fact that the MEA structure contains both an -NH2 and an -OH group that facilitate hydrogen bonding within the clusters, in addition to the electrostatic interactions. Due to this already strong H-bond network, water has a relatively small influence on new particle formation (NPF) and growth in this system, in contrast to MSA reactions with alkylamines. Acid/base molar ratios of unity for 4-12 nm particles were measured using thermal desorption chemical ionization mass spectrometry. The data indicate that reaction of MEA with MSA may dominate NPF under some atmospheric conditions. Thus, the unique characteristics of alkanolamines in NPF must be taken into account for accurate predictions of impacts of CCS on visibility, health and climate.

High-throughput label-free opioid receptor binding assays using an automated desorption electrospray ionization mass spectrometry platform.

The current opioid epidemic has incentivized the discovery of new non-addictive analgesics, a process that requires the screening of opioid receptor binding, traditionally performed using radiometric assays. Here we describe a label-free alternative based on high-throughput (1 Hz) ambient mass spectrometry for screening the receptor binding of new opioid analogues.

Recent developments and applications of ambient mass spectrometry imaging in pharmaceutical research: an overview.

The application of ambient mass spectrometry imaging "MSI" is expanding in the areas of fundamental research on drug delivery and multiple phases of the process of identifying and developing drugs. Precise monitoring of a drug's pharmacological workflows, such as intake, distribution, metabolism, and discharge, is made easier by MSI's ability to determine the concentrations of the initiating drug and its metabolites across dosed samples without losing spatial data. Lipids, glycans, and proteins are just a few of the many phenotypes that MSI may be used to concurrently examine. Each of these substances has a particular distribution pattern and biological function throughout the body. MSI offers the perfect analytical tool for examining a drug's pharmacological features, especially in vitro and in vivo effectiveness, security, probable toxic effects, and putative molecular pathways, because of its high responsiveness in chemical and physical environments. The utilization of MSI in the field of pharmacy has further extended from the traditional tissue examination to the early stages of drug discovery and development, including examining the structure-function connection, high-throughput capabilities in vitro examination, and ex vivo research on individual cells or tumor spheroids. Additionally, an enormous array of endogenous substances that may function as tissue diagnostics can be scanned simultaneously, giving the specimen a highly thorough characterization. Ambient MSI techniques are soft enough to allow for easy examination of the native sample to gather data on exterior chemical compositions. This paper provides a scientific and methodological overview of ambient MSI utilization in research on pharmaceuticals.

Laser capture microdissection and native mass spectrometry for spatially-resolved analysis of intact protein assemblies in tissue.

Previously, we have shown that native ambient mass spectrometry imaging allows the spatial mapping of folded proteins and their complexes in thin tissue sections. Subsequent top-down native ambient mass spectrometry of adjacent tissue section enables protein identification. The challenges associated with protein identification by this approach are (i) the low abundance of proteins in tissue and associated long data acquisition timescales and (ii) irregular spatial distributions which hamper targeted sampling of the relevant tissue location. Here, we demonstrate that these challenges may be overcome through integration of laser capture microdissection in the workflow. We show identification of intact protein assemblies in rat liver tissue and apply the approach to identification of proteins in the granular layer of rat cerebellum.

Present and future perspectives on mass spectrometry for clinical microbiology

In the last decade, MALDI-TOF Mass Spectrometry (MALDI-TOF MS) has been introduced and broadly accepted by clinical laboratory laboratories throughout the world as a powerful and efficient tool for rapid microbial identification. During the MALDI-TOF MS process, microbes are identified using either intact cells or cell extracts. The process is rapid, sensitive, and economical in terms of both labor and costs involved. Whilst MALDI-TOF MS is currently the gold-standard, it suffers from several shortcomings such as lack of direct information on antibiotic resistance, poor depth of analysis and insufficient discriminatory power for the distinction of closely related bacterial species or for reliably sub-differentiating isolates to the level of clones or strains. Thus, new approaches targeting proteins and allowing a better characterization of bacterial strains are strongly needed, if possible, on a very short time scale after sample collection in the hospital. Bottom-up proteomics (BUP) is a nice alternative to MALDI-TOF MS, offering the possibility for in-depth proteome analysis. Top-down proteomics (TDP) provides the highest molecular precision in proteomics, allowing the characterization of proteins at the proteoform level. A number of studies have already demonstrated the potential of these techniques in clinical microbiology. In this review, we will discuss the current state-of-the-art of MALDI-TOF MS for the rapid microbial identification and detection of resistance to antibiotics and describe emerging approaches, including bottom-up and top-down proteomics as well as ambient MS technologies.

Rapid desorption and analysis for illicit drugs and chemical profiling of fingerprints by SICRIT ion source.

Forensic analysis can encompass a wide variety of analytes from biological samples including DNA, blood, serum, and fingerprints to synthetic samples like drugs and explosives. In order to analyze this variety, there are various sample preparation techniques, which can be time-consuming and require multiple analytical instruments. With recent advancements in ambient ionization mass spectrometry (MS), plasma-based dielectric barrier discharge ionization (DBDI) sources have demonstrated to cover a wide range of these analytes. The flow-through design of this source also allows for easy connection to a thermal desorption type of sample introduction. We present an in-house built thermal desorption device where the sample is introduced via a glass slide, which gets heated and transferred to the DBDI-MS with nitrogen for identification and semi-quantification. Using a glass slide as an inexpensive sampling device, detection limits as low as 20 pg for fentanyl are demonstrated. Additionally, a very precise (>96% accuracy) identification of persons based on the chemical profile of their fingerprints is possible, establishing a direct analytical link of the drug trace to the individual in one measurement. We compared the DAG, TAG, sterol, and (semi-)volatile region of the averaged fingerprint spectra over multiple days, showing the best model accuracy for identification based on the DAG region. The combination of thermal desorption and DBDI-MS minimized sample preparation, leading to an ultrasensitive and rapid analysis of illicit drug traces and the identification of underlying personas based on fingerprints.

Designing a Novel Setup for High-Throughput Investigations of Electrochemical Reactions in Real Time

With the great interest in new electrochemical processes, fast screening of various reaction parameters is highly desirable. For this purpose, differential electrochemical mass spectrometry (DEMS) and membrane-inlet mass spectrometry (MIMS) have been established to enable real-time monitoring of volatile compounds. However, the analysis of non-volatile compounds is commonly limited by the temporal resolution of traditional quantification methods such as NMR, GC-MS, or LC-MS. While ambient ionization mass spectrometry (AIMS) generally enables time-resolved monitoring of non-volatile compounds, electrolyte salts can lead to ionization suppression. The latter can decrease the sensitivity of product detection and the reliability of quantitative data. Therefore, a suitable reaction setup and thorough investigations are needed when utilizing AIMS. Nonetheless, in recent efforts, an electrochemical flow cell was coupled with such a technique to provide a method for on-line monitoring of non-voltile reaction products in aqueous electrolytes. To keep up with the increasing interest in electrosynthesis in organic media, we now present a new setup that is also applicable to non-aqueous media. It pairs a novel and versatile electrochemical cell with an AIMS and DEMS for highly sensitive detection of reaction products. Moreover, various reaction parameters such as electrode material, electrolyte, and temperature can be investigated in high-throughput.Key words: Electrocatalysis, Electrosynthesis, Real-time, On-line monitoring, High-throughput

Determination of C═C Positions of Unsaturated Fatty Acids in Foods via Ambient Reactive Desorption Ionization with Water Dimer Radical Cations.

The positions of C═C bonds in unsaturated fatty acids (FAs) are one of the main factors determining the quality of food flavor. Herein, we developed an approach for the determination of C═C bonds of FAs by online epoxidation reaction with water dimer radical cations. The limit of detection for octenoic acid isomers was ∼9 μg/L. The positions of C═C bonds in trans-2/3-hexenoic acid, trans-2/3-octenoic acid, oleic acid, linoleic acid, and linolenic acid in black tea or olive oil samples were directly determined by the established method. These results indicate that the established method allows the rapid determination of unsaturated FAs in black tea and olive oil. The advantages of this approach include the analysis speed (∼1 min per sample), simple device, and no need for complex pretreatment. This study not only provides a strategy for the determination of C═C positions but also offers new possibilities for applications in the field of food chemistry.

Photocatalytic degradation-based ambient mass spectrometry imaging for enhancing detection coverage of poorly-ionizable lipidomes

Localization of lipidomes and tracking their spatial changes in tissues by mass spectrometry imaging (MSI) plays an important role in unveiling the mechanisms of living processes, diseases and therapeutic treatments. However, it is always challenging to achieve direct MSI of poorly-ionizable lipids, such as glycolipids and glycerolipids, due to the strong ion suppression and isobaric peaks interference from high-abundance phosphatidylcholines (PCs) in tissues. Here we developed a photocatalytic degradation-based ambient liquid extraction MSI method to largely enhance the detection coverage of poorly-ionizable lipids by rapid online removal of PCs in MSI. Phospholipids were found to be selectively photodegraded on TiO2 surface in acidic conditions in the presence of water under UV irradiation, while other poorly-ionizable lipids remained. Sulfate ion could largely improve the degradation efficiencies. Anatase nanoparticles-embedded TiO2 monolith was in-situ synthesized in the capillary of ambient liquid extraction system, and rapid online photodegradation of PCs was achieved during MSI with efficiency >80 %, largely reducing ion suppression. The pathway analysis showed that PC was oxidatively degraded starting from hydroxylation of C=C bonds. With intense UV irradiation, PCs were completely degraded into small molecules<200 Da without interference on the detection of endogenous lipids. With the new MSI method, detection coverage to cerebrosides, ceramides and diglycerides was enhanced by 2–9 times comparing with traditional MSI. Clearer localizations were observed for poorly-ionizable lipids via the new method than traditional method. Thus, this work provided a complementary MSI method for traditional MSI to address the issues on direct imaging of poorly ionizable lipids in ambient conditions.

Determination of MCPA in environmental samples using an analytical on-line system based on imprinted poly[2-(3-butenyl)-2-oxazoline] and ambient ionization mass spectrometry

Monitoring and quantifying organic chemicals in the environment play a vital role in understanding their behavior and ensuring environmental safety. MCPA (2-methyl-4-chlorophenoxyacetic acid) is a commonly used phenoxy herbicide that poses potential risks to aquatic life. In this study, we present an innovative analytical approach for MCPA quantification, employing molecularly imprinted polymers (MIPs) for selective extraction and ambient plasma mass spectrometry for direct on-line analysis. To synthesize functional MIPs, we employed a post-polymerization strategy based on a thiol-ene click reaction conducted on a short-chain poly[2-(3-butenyl)-2-oxazoline] (poly(ButenOx)) that allowed attachment of 3-mercaptopropionic acid (MPA) to polymer side chains. The incorporation of MPA groups into polymer structure enabled the attainment of elevated maximum adsorption capacities and enhanced selectivity towards MCPA. Utilizing a specially designed ambient plasma mass spectrometry setup, we successfully quantified MCPA in water samples, achieving significantly improved detection limits compared to conventional solution-based analysis, whereas the quantification of MCPA in real-life river water samples demonstrated excellent recoveries. In conclusion, this novel analytical method employing MIPs and ambient plasma mass spectrometry provides an effective and sensitive approach for accurate MCPA detection in environmental water samples. The technique holds promise for facilitating reliable monitoring and management of MCPA levels in aquatic ecosystems.