Alginate Gel Research Articles

Preparation of KHA/SA/MMT composites and their adsorption properties for Rhodamine B.

Two natural adsorbent materials, potassium humate (KHA) and montmorillonite (MMT), were successfully prepared by embedding them in sodium alginate (SA) gel spheres through physical cross-linking with CaCl2. And CaCO3 was used as a porogenic agent to prepare the porous composites, KHA/SA/MMT. The materials were characterized by using XRD, TGA, SEM, and N2 adsorption/desorption equipment. The results showed that MMT and KHA were successfully embedded in the SA gel; the introduction of MMT increased the thermal stability of the composites and the embedding of MMT, and the porogenic effect of CaCO3 increased the specific surface area of the composites substantially, which provided favorable conditions for adsorption and treatment of pollutants. In addition, a one-way exploratory experiment yielded a higher removal rate of Rhodamine B (RhB) at D = 0.6 g/L, pH = 5, C0 = 100 mg/L, and t = 360 min. The adsorption kinetics and adsorption isotherm conformed to the secondary kinetic model and Langmuir model, respectively, and the maximum adsorption of RhB by KHA/SA/MMT could reach up to 884.96 mg/g at 303 K. The adsorption mechanism for RhB was shown by FT-IR and XPS analyses to be possibly bound by non-covalent bonding forces. After seven consecutive adsorption-desorption cycles, the adsorption of RhB by KHA/SA/MMT still reached 80.75%. Therefore, the prepared gel spheres have the advantages of easy regeneration and efficient reuse and great potential for application in purifying RhB from wastewater.

Experimental Investigation of Excitation Strategies for Erosion by Cavitation Histotripsy

Abstract Cavitation histotripsy has been applied to the disintegration on the surface of soft tissue in a well-controlled manner. Its performance was assumed to be determined by the acoustic pressure alone. Long pulse duration with low pulse repetition frequency (PRF) can also successfully generate erosion. This study was designed to investigate the excitation strategies for cavitation histotripsy-induced erosion. The erosion area and volumes produced by cavitation histotripsy on the alginate gel phantom using single-frequency, dual-frequency, and two pulsed excitations at the same power output at the PRF of 1 Hz and 200 Hz were compared. Dual-frequency excitation can improve the erosion at all PRFs, while pulsed excitations decrease it at the PRF of 200 Hz. Using both pulsed and dual-frequency excitations has more erosion areas than using single-frequency at a PRF of 1 Hz. In comparison, although the induced erosion areas using the pulsed excitations are larger than those of single-frequency at the PRF of 200 Hz, the erosion volumes are much lower than those of dual-frequency excitation. It suggests that a sufficient long pulse duration is another important factor for the performance of cavitation histotripsy. Dual-frequency excitation or amplitude modulation by the low-frequency sinusoidal envelope can achieve more erosion than that produced by single-frequency excitation at the same power output in a wide range of PRFs.

Standardization of Formulation and Application Approaches for Field Implementation of EPNs

Entomopathogenic nematodes (EPNs) live parasitically inside the infected insect host, and so they are termed as endoparasitic. They infect different types of insect living in the soil like the larval forms of moths, butterflies and beetles as well as adult forms of beetles, grasshoppers and crickets. The present experiment was conducted under both laboratory and field conditions at CCS Haryana Agriculture University, Hisar. Two most virulent strains of EPNs, Metarhabditis amsactae strain HAR-St-II and HAR-Ht-III were taken and their formulations were standardized using six different media i.e. cadaver based formulation, water, alginate gel, foam chips, clay chips and water dispersible granules. Among these formulations, cadaver based formulation was found to be best. Maximum numbers of active IJs after 90 days were obtained from this formulation were 3370 and 2728 /Petri plate in strain HAR-St-II and HAR- Ht-III of M. amsactae, respectively. Further this, experiment was conducted at field level for EPNs suspension was standardized using different size of nozzle opening i.e. 25 µm, 50 µm, 75 µm and 100 µm on knapsack sprayer. Spodoptera litura was selected as a test insect in okra crop for foliar application of EPNs and results revealed that 100 µm nozzle opening size gave maximum larval mortality of S. litura. Per cent mortality of S. litura was increased with increase in size of nozzle and period of observation

A new bacteria-based self-healing system triggered by sulfate ion for cementitious material

Concrete in complex environments is prone to cracking due to its own brittle and porous characteristics. When environmental sulfate ions intrude into concrete, the formation of gypsum and ettringite can lead to unrestricted expansion and subsequent cracking of the concrete, so a self-healing system that responds to environmental ions is necessary. In this study, barium-doped calcium alginate gels that could be triggered by sulfate ions were used to encapsulate microbial-based repairing agents. Experimental results showed that Bacillus spores of up to 40% mass were encapsulated in a modified alginate hydrogel, which had good compatibility with bacteria and concrete. Meanwhile, the sensitivity of microcapsules to sulfate at different concentrations was also verified. The new self-healing system introduces two response modes, namely sulfate triggering and mechanical stimulation, to address concrete cracks at various ages. Even for cracks that emerge 60 days later, the crack healing ratio can still reach 80%. Additionally, the new system can provide organic-inorganic composite repairing products to maintain the stability of the repaired structures at the crack site. The repair system demonstrates good uniformity and compatibility, and the negative impact on mechanical performance can be alleviated by reducing particle size. To conclude, the new self-healing system has great potential for concrete applications in saline or marine environments.

Development of antioxidant sodium alginate gel beads encapsulating curcumin/gum Arabic/gelatin microcapsules

In this study, we developed a sodium alginate gel bead (Sbs-Mcs-Cur) encapsulating curcumin microcapsules (Mcs-Cur) to protect the bioaccessibility of curcumin in the gastrointestinal tract and enhance its edible efficiency. Structural characterization indicated that curcumin was successfully encapsulated in Sbs-Mcs-Cur. Antioxidant capacity experiments demonstrated that Sbs-Mcs-Cur successfully eliminated over 90% of DPPH and ABTS free radicals. The release behavior of Sbs-Mcs-Cur was evaluated using a simulated gastrointestinal model. Release rate in vitro measurements showed that Sbs-Mcs-Cur had a low release rate (<0.5%) in simulated gastric fluid (SGF), while more than 97.2% were released in simulated intestinal fluid (SIF), indicating that Sbs-Mcs-Cur could mitigate inhibition of microcapsule solubilization caused by the gastric environment, and effectively enhancing the release rate of curcumin in the intestine. These present findings demonstrated that the sodium alginate hydrogel system equipped with gum Arabic/gelatin microcapsules could be used as an ideal carrier for delivering hydrophobic bioactive substances like curcumin in functional food systems.

Slow-sculpting graphene oxide/alginate gel loaded with platelet-rich plasma to promote wound healing in rats.

Wounds, especially chronic wounds, have become an important problem that endangers human health. At present, there are many repair methods, and among them combines materials science and biology is one of the important repair methods. This study explored the preparation method, physicochemical properties, biological activity and safety of Platelet-Rich plasma (PRP)-loaded slow-sculpting graphene oxide (GO)/alginate gel, and applied it to acute full-thickness skin defect wounds in rats to observe its role in wound healing. The results show that the slow-sculpting GO/alginate gel has excellent plasticity and is suitable for a variety of irregularly shaped wounds. At the same time, its porous structure and water content can maintain the activity of platelets and their released growth factors in PRP, thereby promoting wound collagen synthesis and angiogenesis to accelerate wound healing. This indicates that the slow-sculpting GO/alginate gel is an excellent loading material for PRP, and the combination of the two may become one of the methods to promote wound repair.

Aspherical, Nano-Structured Drug Delivery System with Tunable Release and Clearance for Pulmonary Applications.

Addressing the challenge of efficient drug delivery to the lungs, a nano-structured, microparticulate carrier system with defined and customizable dimensions has been developed. Utilizing a template-assisted approach and capillary forces, particles were rapidly loaded and stabilized. The system employs a biocompatible alginate gel as a stabilizing matrix, facilitating the breakdown of the carrier in body fluids with the subsequent release of its nano-load, while also mitigating long-term accumulation in the lung. Different gel strengths and stabilizing steps were applied, allowing us to tune the release kinetics, as evaluated by a quantitative method based on a flow-imaging system. The micro-cylinders demonstrated superior aerodynamic properties in Next Generation Impactor (NGI) experiments, such as a smaller median aerodynamic diameter (MMAD), while yielding a higher fine particle fraction (FPF) than spherical particles similar in critical dimensions. They exhibited negligible toxicity to a differentiated macrophage cell line (dTHP-1) for up to 24 h of incubation. The kinetics of the cellular uptake by dTHP-1 cells was assessed via fluorescence microscopy, revealing an uptake-rate dependence on the aspect ratio (AR = l/d); cylinders with high AR were phagocytosed more slowly than shorter rods and comparable spherical particles. This indicates that this novel drug delivery system can modulate macrophage uptake and clearance by adjusting its geometric parameters while maintaining optimal aerodynamic properties and featuring a biodegradable stabilizing matrix.

Facile preparation of sodium alginate gel beads enhanced by polyamino-modified 3D carbon for efficient remediation of organic dyes in wastewater

The existence of organic dyes wastewater had caused serious harm to the environment and human beings. Herein, in this study, a simple and efficient method was selected to synthesize sodium alginate gel beads adsorbent (CPS-Bead) with porous structure and high adsorption performance. Interestingly, the addition of polyamino-modified 3D carbon materials (GO-CNT) enhanced the related properties of gel beads. Moreover, the well-designed adsorbent was used to remove methylene blue (MB), malachite green (MG), crystal violet (CV), and congo red (CR) from dyes wastewater. The results showed that the adsorption capacity of CPS-Bead on MB, MG, CV and CR could reach the highest of 2191.39 mg/g, 2201.69 mg/g, 1669.11 mg/g and 2096.04 mg/g at 318 K, respectively. The kinetic behavior and the isotherm behavior of CPS-Bead was more consistent with the nonlinear model of pseudo-second-order dynamics and the Langmuir isotherm model, and the thermodynamic data showed that the adsorption process of the four dyes was automatic. In addition, CPS-Bead also demonstrated excellent adsorption performance in cyclic experiments, selectivity experiments and adsorption column experiments, which could selectively and continuously adsorb different dyes. Overall, the prepared gel beads not only showed outstanding adsorption capacity, but also the had an excellent reusability, besides, CPS-Bead had great potential industrial applications.

Developing a transcatheter injectable nanoclay- alginate gel for minimally invasive procedures

Shear-thinning materials have held considerable promise as embolic agents due to their capability of transition between solid and liquid state. In this study, a laponite nanoclay (NC)/alginate gel embolic agent was developed, characterized, and studied for transcatheter based minimally invasive procedures. Both NC and alginate are biocompatible and FDA-approved. Due to electrostatic interactions, the NC/alginate gels exhibit shear-thinning properties that are desirable for transcatheter delivery. The unique shear-thinning nature of the NC/alginate gel allows it to function as a fluid-like substance during transcatheter delivery and as a solid-like embolic agent once deployed. To ensure optimal performance and safety in clinical applications, the rheological characteristics were thoroughly investigated to optimize the mechanical properties of the NC/alginate gel, including storage modulus, yield stress/strain, and thixotropy. To improve physicians' experience and enhance the predictability of gel delivery, a combination of experimental and theoretical approaches was used to assess the injection force required for successful delivery of the gel through clinically employed catheters. Overall, NC/alginate gel exhibited excellent stability and tunable injectability by optimizing the composition of each component. These findings highlight the gel's potential as a robust embolic agent for a wide range of minimally invasive procedures.

Transmembrane stem factor nanodiscs enhanced revascularization in a hind limb ischemia model in diabetic, hyperlipidemic rabbits

Therapies to revascularize ischemic tissue have long been a goal for the treatment of vascular disease and other disorders. Therapies using stem cell factor (SCF), also known as a c-Kit ligand, had great promise for treating ischemia for myocardial infarct and stroke, however clinical development for SCF was stopped due to toxic side effects including mast cell activation in patients. We recently developed a novel therapy using a transmembrane form of SCF (tmSCF) delivered in lipid nanodiscs. In previous studies, we demonstrated tmSCF nanodiscs were able to induce revascularization of ischemia limbs in mice and did not activate mast cells. To advance this therapeutic towards clinical application, we tested this therapy in an advanced model of hindlimb ischemia in rabbits with hyperlipidemia and diabetes. This model has therapeutic resistance to angiogenic therapies and maintains long term deficits in recovery from ischemic injury. We treated rabbits with local treatment with tmSCF nanodiscs or control solution delivered locally from an alginate gel delivered into the ischemic limb of the rabbits. After eight weeks, we found significantly higher vascularity in the tmSCF nanodisc-treated group in comparison to alginate treated control as quantified through angiography. Histological analysis also showed a significantly higher number of small and large blood vessels in the ischemic muscles of the tmSCF nanodisc treated group. Importantly, we did not observe inflammation or mast cell activation in the rabbits. Overall, this study supports the therapeutic potential of tmSCF nanodiscs for treating peripheral ischemia.

Green magnetic carbon/alginate biocomposite beads from iron scrap waste for efficient removal of textile dye and heavy metal

The circular economy can help enhance the value of industrial waste and remediate the environment. This study considers the application of iron scrap from steel production as a free resource to produce magnetic adsorbent beads to remove methylene blue dye and lead (II) ions from wastewater. Composite beads were prepared by incorporating iron scrap and activated carbon into a calcium alginate gel using a simple ‘mix and drop’ synthesis. The optimized magnetic beads were stable and offered a large specific surface area. The maximum adsorption capacity of the adsorbent, calculated from the Langmuir isotherm model, was 476.19 mg g−1 for methylene blue and 163.93 mg g−1 for lead (II) ions. This study places emphasis upon the zero-waste principle and employs a scalable synthetic approach for the conversion of waste iron scrap into an adsorbent material capable of delivering significant environmental benefits.

Alginate Gel Encapsulated with Enzybiotics Cocktail Is Effective against Multispecies Biofilms.

The development of new and effective antibacterials for pharmaceutical or cosmetic skin care that have a low potential for the emergence and expansion of bacterial resistance is of high demand in scientific and applied research. Great hopes are placed on alternative agents such as bactericidal peptidoglycan hydrolases, depolymerases, etc. Enzybiotic-based preparations are being studied for the treatment of various infections and, among others, can be used as topical formulations and dressings with protein-polysaccharide complexes. Here, we investigate the antibiofilm properties of a novel enzybiotic cocktail of phage endolysin LysSi3 and bacteriocin lysostaphin, formulated in the alginate gel matrix and its ability to control the opportunistic skin-colonizing bacteria Staphylococcus aureus, Pseudomonas aeruginosa, and Klebsiella pneumoniae, as well as mixed-species biofilms. Our results propose that the application of SiL-gel affects different components of biofilm extracellular polymeric substances, disrupts the matrix, and eliminates the bacteria embedded in it. This composition is highly effective against biofilms composed of Gram-negative and Gram-positive species and does not possess significant cytotoxic effects. Our data form the basis for the development of antibacterial skin care products with a gentle but effective mode of action.

Invasive plant-derived biochar for sustainable bioremediation of pesticide contaminated soil

Managing invasive plant presents a significant challenge to both the environment and the economy. There is an opportunity to address this issue by utilizing invasive plants as a sustainable and cost-effective source of valuable functional materials for environmental remediation. In this study, a promising Mikania micrantha biochar (MB) was synthesized by pyrolyzing an invasive plant, which was utilized for bacterial immobilization and adsorption of contaminants. By embedding Proteus terrae ZQ02-MB within a polyvinyl alcohol-sodium alginate gel to create a biochar-modified bacterial microsphere (BBM), the superior degradation of pesticide contaminants was observed. Taking chlorothalonil (CHT) as an example, field experiments demonstrated that BBM achieved a removal efficiency of 59.8% by the third day. Additionally, BBM not only improved the richness and diversity of soil bacteria but also enhanced the microbial community structure by the seventh day. On this basis, the adsorption capacity of MB, biofilm growth promoting ability of BBM, and the CHT mineralization ability of strain ZQ02 were validated as a joint mechanism to promote efficient CHT removal. Overall, this study proposes a composite model of invasive plant-derived biochar loaded microorganisms, which has great potential in eliminating pollutant residues and paves new paths to develop strategies for reusing invasive species resources.

Development of alginate macroporous hydrogels using sacrificial CaCO3 particles for enhanced hemostasis

Polymeric hydrogels have increasingly garnered attention in the field of hemostasis. However, there remains a lack of targeted development and evaluation of non-dense polymeric hydrogels with physically incorporated pores to enhance hemostasis. Here, we present a facile route to macroporous alginate hydrogels using acid-induced CaCO3 dissolution to provide Ca2+ for alginate gelation and CO2 bubbles for subsequent macropore formation. The as-prepared pore structure in the hydrogels and its formation mechanisms were characterized through microscopic imaging and nitrogen adsorption/desorption tests. Functional analyses revealed that the macroporous hydrogels exhibited improved rheology, blood absorption, coagulation factor delivery, and platelet aggregation. Ultimately, the introduction of pores significantly enhanced the hemostatic effectiveness of alginate hydrogels in vivo, as demonstrated in rat tail amputation and liver injury models, leading to a reduction in blood loss of up to 77 % or a decrease in bleeding time of up to 88 %. Notably, hydrogels with higher porosity achieved with a CaCO3 to alginate ratio of 40 % outperformed those with lower porosity in the aforementioned properties. Furthermore, these improvements were found to be biocompatible and elicited minimal inflammation. Our findings underscore the potential of a simple porous hydrogel design to enhance hemostasis efficacy by physically incorporating macropores.

A novel “microbiota-host interaction model” to study the real-time effects of fermentation of non-digestible carbohydrate (NDCs) on gut barrier function

In this study, an in vitro co-culture model using an electric cell-substrate impedance sensing system (ECIS) for testing the impact of real-time fermentation of non-digestible carbohydrates (NDCs) by the intestinal microbiota on gut barrier function was established. We applied Lactobacillus plantarum WCFS1 as a model intestinal bacterium and alginate-pectin as immobilization polymers as well as a source of NDCs to determine the impact of pectin fermentation on the barrier function of T84 gut epithelial cells. In the first design, L. plantarum WCFS1 was encapsulated in an alginate capsule followed by embedding in an agar layer to mimic a firm mucus layer that might be present in the colon. In this experimental design, the presence of the agar layer interfered with the transepithelial electrical resistance (TEER) measurement of T84 cells. Subsequently, we removed the agar layer and used encapsulated bacteria in an alginate gel and found that the TEER measurement was adequate. The encapsulation of the L. plantarum WCFS1 does avoid direct contact with cells. Also, the encapsulation system allows higher amounts of packing densities of L. plantarum WCFS1 in a limited space which can limit the oxygen concentration within the capsule and therefore create anaerobic conditions. To test this design, T84 cells were co-incubated with L. plantarum alginate-capsules supplemented with graded loads of fermentable pectin (0, 4, and 8 mg/ml per capsule) to investigate the effect of pectin fermentation on gut barrier function. We observed that as the pectin content in the L. plantarum capsules increased, pectin showed a gradually stronger protective effect on the TEER of the gut epithelium. This could partly be explained by enhanced SCFA production as both lactate and acetate were enhanced in L. plantarum containing alginate capsules with 8 mg/ml pectin. Overall, this newly designed in vitro co-culture model allows for studying the impact of bacteria-derived fermentation products but also for studying the direct effects of NDCs on gut barrier function in a relatively high-throughput way.

Protein Isolation from 3D Hydrogel Scaffolds.

Protein isolation is an essential tool in cell biology to characterize protein abundance under various experimental conditions. Several protocols exist, tailored to cell culture or tissue sections, and have been adapted to particular downstream analyses (e.g., western blotting or mass spectrometry). An increasing trend in bioengineering and cell biology is to use three-dimensional (3D) hydrogel-based scaffolds for cell culture. In principle, the same protocols can be used to extract protein from hydrogel-based cell and tissue constructs. However, in practice the yield and quality of the recovered protein pellet is often substantially lower when using standard protocols and requires tuning of multiple steps, including the selected lysis buffer and the scaffold homogenization strategy, as well as the methods for protein purification and reconstitution. We present here specific protocols tailored to common 3D hydrogels to help researchers using hydrogel-based 3D cell culture improve the quantity and quality of their extracted protein. We focus on three materials: protease-degradable PEG-based hydrogels, collagen hydrogels, and alginate hydrogels. We discuss how the protein extraction procedure can be adapted to the scaffold of interest (degradable or non-degradable gels), proteins of interests (soluble, matrix-bound, or phosphoproteins), and downstream biochemical assays (western blotting or mass spectrometry). With the growing interest in 3D cell culture, the protocols presented should be useful to many researchers in cell biology, protein science, biomaterials, and bioengineering communities. © 2024 The Authors. Current Protocols published by Wiley Periodicals LLC. Basic Protocol 1: Isolating proteins from PEG-based hydrogels Basic Protocol 2: Isolating proteins from collagen hydrogels Basic Protocol 3: Isolating proteins from alginate hydrogels Alternate Protocol: Isolating protein from alginate gels using EDTA to dissolve the gel Support Protocol: Isolating protein and RNA simultaneously from the same samples.

Improved application of immobilized Enterobacter cloacae into a bio-based polymer for Reactive Blue 19 removal, an eco-friendly advancement in potential decolorizing systems.

The widespread use of highly complex synthetic dyes like reactive dyes in the textile industry has some adverse environmental impacts and deserves close attention. Biological treatment of these effluents utilizing various species of bacteria with remarkable efficiency in dye removal is still considered promising. Our current study deals with immobilizing an isolated bacterial strain into calcium alginate (Ca/Alg) gel beads and using it to treat pernicious pollutants like synthetic dyes. A potential Reactive Blue 19 (RB19)-degrading Enterobacter cloacae strain A1 was isolated from the Kashan textile industry and was characterized by 16S rDNA gene sequencing. The decolorization ability of strain A1 was assessed by time-based studies using free bacterial cells/immobilized in Ca/Alg. Based on the results of the 16S rDNA gene sequencing, it appears that strain A1 belonged to E.cloacae, with a 99.74% similarity. The findings suggest that immobilized strain A1 accomplished maximum decolorization activity compared with the free cells. The immobilized strain could utterly decompose and decolorize 0.05 mg/mL of RB19 within 48 h, while the free bacterial strain decolorized RB19 within 5 days. Moreover, Ca/Alg gel beads can maintain their efficiency for over three decolorization cycles. Further infrared spectroscopy (FTIR) and gas chromatograph mass spectrometer (GC/MS) investigation declared complete RB19 decomposition on reaction products. Artemia salina was used to investigate the toxicity of dye and its degraded metabolites. The LC50 values signified the pure dye as very toxic with 0.01 mg/mL concentration, while after-treatment products showed no toxic effect on larvae. This immobilization technique increased the applicability of bacterial strain for dye removal. It was beneficial for the decolorization of RB19 from textile wastewater due to a remarkable reduction in time. Notably, strain A1-immobilized beads can maintain their activity for three consecutive decolorization cycles without a considerable decrease in efficiency. PRACTITIONER POINTS: The remarkable capacity of immobilized Enterobacter cloacae strain A1 for Reactive Blue 19 (RB19) removal Immobilized A1 strain showed two-fold higher removal than free one over 48 h A promising method for enhancing RB19 decolorization Decolorization was due to degradation based on UV-Vis, FTIR, and GC/MS analysis Non-toxic posttreatment products for Artemia.

High-efficiency and conveniently recyclable g-C3N4/diatomite/calcium alginate composite gel bead photocatalysts

Graphitic carbon nitride (g-C3N4) is considered an encouraging photocatalyst with visible light activity. However, the utilization of g-C3N4 nanosheets in powdered form in wastewater treatment presents difficulties in the recovery and recycling of photocatalysts. Consequently, supported g-C3N4 photocatalysts have been developed for practical applications. In the present work, a novel, conveniently recyclable composite gel bead photocatalyst, comprised of g-C3N4/diatomite/calcium alginate, has been fabricated using a dropwise addition strategy. The systematic investigation of photocatalytic activity and photochemical stability of the composite gel beads was conducted through the degradation of methylene blue (MB) under visible light exposure (λ > 420 nm). As a result, g-C3N4/diatomite/calcium alginate gel beads show a high photocatalytic effectiveness of 95% when MB solution is disintegrated at 120 minutes.

Rheology of bolus as a wet granular matter – Influence of saliva on rheology of polysaccharide gel beads

In the present work, the rheological properties of model boli were analysed based on the granular matter physics. Polysaccharide microgels mixed with artificial saliva were prepared as model boli. The storage modulus G′ of alginate gel beads increased and then decreased with increasing content of artificial saliva. Surface of alginate gel beads prepared by dripping into calcium chloride solution were wiped to remove the moisture to mimic the oral condition of the Sjögren's syndrome. G′ decreased monotonically with increasing artificial saliva beyond a certain amount of the added saliva, which is similar to the widely observed characteristic of wet granular materials. Although the analysis is limited to a model bolus at a certain stage of oral processing mimicked by instrumentally prepared microgels of uniform size and shape, it revealed some fundamental aspects highlighting the implication of a wet granular matter as a useful concept for further understanding of the bolus rheology.

Terbium alginate encapsulated CsPbI3@Pb-MOF: a ratiometric fluorescent bead for detection and adsorption of Fe3.

Halide perovskite nanocrystals are innovative luminescent materials for fluorescent probes with high quantum yield and narrow emission bandwidth. However, the limited stability, single-signal response, and separation challenges obstruct their widespread use in water ion detection. Herein, a ratiometric fluorescence sensor based on terbium alginate gel beads (green fluorescent, namely Tb-AG) embedded with powdered CsPbI3@Pb-MOF (red fluorescent) was prepared for fluorescent determination and adsorption of Fe3+. Pb-MOF's protection notably enhances the water stability of CsPbI3, while the energy transfer between CsPbI3@Pb-MOF and Tb3+ elevates the optical performance of CsPbI3@Pb-MOF@Tb-AG. Significantly, Fe3+ markedly suppresses CsPbI3@Pb-MOF red fluorescence at 647 nm, while not noticeably affecting Tb-AG green emission at 528 nm. The sensor exhibited a strong linear response to Fe3+ concentrations ranging from 0 to 90 μM, with a detection limit of 0.44 μM and high selectivity. The CsPbI3@Pb-MOF@Tb-AG-based sensor has been effectively validated through its successful use in detecting Fe3+ in tap and river water samples. Furthermore, CsPbI3@Pb-MOF@Tb-AG demonstrates a notable adsorption capacity of 325.4 mg g-1 Fe3+. Finally, the mechanism of Fe3+ detection and adsorption was determined.