Airflow Direction Research Articles

Climate warming detected in caves of the European Alps

Cave air temperatures in four caves in the European Alps show statistically significant warming trends of about 0.2 °C per decade over the last two decades (2000–2020). These trends are about half as large as those observed outside and are characterized by a remarkable spatial and temporal consistency. The investigated caves represent different types in terms of their ventilation regime and one of them also hosts perennial ice. Key observation sites are located in cave sections where the temporal variability of air temperature is strongly attenuated compared to outside conditions and data from different cave sections show that the main results are valid for large parts of the investigated caves. Continued warming will lead to broad changes in alpine cave environments, including changes in strength and direction of air flow in caves, karst hydrology and subsurface ecosystems. The observed subsurface warming has a particular strong effect on the long-term preservation of perennial ice present in some of these caves. This is shown for an ice cave in the Austrian Alps, where enhanced melt of ice correlates with the observed warming. This cave (and similar ones) will not be able to hold perennial ice beyond the next decade.

Recent Patents on Long Distance Pneumatic Conveying Technology

Background: Pneumatic conveying is the use of air flow energy to transport granular materials in the direction of airflow in a closed pipeline, which involves the disadvantages of low conveying efficiency and easy deposition of particles. Objective: It is necessary to develop pneumatic conveying devices to reduce particle deposition, promote particles to enter the flow field again to accelerate, and achieve the effect of extending the pneumatic conveying distance. Method: The anti-settling device re-accelerates the particles so that the particles return to the flow field, which effectively reduces the probability of settlement blockage of material particles during transportation. The pneumatic conveying pressurized separator uses a pot-shaped housing to generate an internal rotating flow field to screen particles, and the light dust adheres to the filter, reducing the possibility of pipeline dust explosion. Results: The anti-settling device can quickly replace the anti-settlement block according to the parameters of the conveying pipeline, which can effectively reduce the probability of settlement blockage of material particles during transportation. The pressurized separator can use the air compressor to cooperate with the return air pipe to effectively remove the dust in the pneumatic conveying pipe and carry out secondary pressurized transportation of the materials in the pneumatic conveying pipe, which improves the safety of pneumatic conveying. Conclusion: The above technology improves the efficiency of pneumatic conveying and gas utilization, enhances the speed of particle conveying, reduces particle settlement and collision, extends the distance of pneumatic conveying, and ensures the safety of pneumatic conveying and the feasibility of industrial applications.

Simulation Analysis of 3-D Airflow and Temperature Uniformity of Paddy in a Laboratory Drying Oven.

This study analyzed the effects of airflow characteristics on the temperature distribution and drying uniformity of paddy during convective drying. Simulations of the drying process with varying airflow inlet and outlet positions were conducted using COMSOL Multiphysics 6.1 software. The determination coefficient (R2) between the simulated data and experimental values of Sample1 (S1), Sample2 (S2), and Sample3 (S3) was calculated, and its average values were 0.964, 0.963, 0.963, and 0.967, respectively. This study demonstrates that the airflow direction and outlet location have a significant impact on the temperature uniformity of the paddy. The vortex structure generated by the obstruction of the sidewalls and paddy influences both the airflow and temperature distribution within the drying chamber. When the outlet was on the left side and the inlet airflow was in a vertical orientation (VO), the temperature distribution of the paddy exhibited higher temperatures in the edge regions and lower temperatures in the center, with a maximum temperature difference of around 16 °C. The time required for the temperature to reach equilibrium with the outlet positioned on the left was 28.6% shorter than with the outlets positioned in the center or on both sides. Moreover, the temperature uniformity of the three paddy samples was better under this condition. The developed model accurately reflected the paddy drying process. It could also be used to analyze the optimal heating uniformity, providing a technical basis for the design of grain dryers.

Avian-inspired embodied perception in biohybrid flapping-wing robotics

Avian feather intricate adaptable architecture to wing deformations has catalyzed interest in feathered flapping-wing aircraft with high maneuverability, agility, and stealth. Yet, to mimic avian integrated somatic sensation within stringent weight constraints, remains challenging. Here, we propose an avian-inspired embodied perception approach for biohybrid flapping-wing robots. Our feather-piezoelectric mechanoreceptor leverages feather-based vibration structures and flexible piezoelectric materials to refine and augment mechanoreception via coupled oscillator interactions and robust microstructure adhesion. Utilizing convolutional neural networks with the grey wolf optimizer, we develop tactile perception of airflow velocity and wing flapping frequency proprioception. This method also senses pitch angle via airflow direction and detects wing morphology through feather collisions. Our low-weight, accurate perception of flapping-wing robot flight states is validated by motion capture. This investigation constructs a biomechanically integrated embodied perception system in flapping-wing robots, which holds significant promise in reflex-based control of complex flight maneuvers and natural bird flight surveillance.

Evaluation of Ventilation Strategies to Mitigate Airborne Infection Risk in a Dental School: A Three-Dimensional CFD Analysis of Airflow Patterns and Ventilation Efficiency

Infection prevention and control is a crucial element in providing a safe environment for dental clinics and reducing airborne infections risks during dental procedures. In response to the prevailing COVID-19 situations, the clinical space in the dental school was operated with ventilation strategies, increasing air exchanges and incorporating supply and return air arrangement based on seating positions. This study evaluated airflow patterns to examine personal exposure to airborne infection risk under these strategies. The three-dimensional computational fluid dynamics technique using computational fluid dynamics (CFD) analysis was performed in 50 multi-units of the dental school of the university in Bangkok, Thailand. The results revealed substantial improvements in indoor ventilation. Improvement of airflow patterns and directions surpassed conventional design of the pre-existing building’s system and helped reduce airborne contaminant concentrations. The further discussion of occupant-based design in dental schools is needed to optimize ventilation systems and engineering controls concerning indoor airborne infections.

Development and tests of the novel configuration of the solar chimney with sensible heat storage

Heating, ventilation, and air conditioning systems account for a significant part of the energy usage in buildings and are primarily responsible for greenhouse gas emissions and operating costs. These can be lowered by the adoption of solar energy. This paper presents the developing and testing of a novel solar chimney with sensible heat storage. The thermal performance and potential contribution of the developed thermal chimney to decreasing residential buildings energy consumption in Polish climate conditions is investigated. The developed solar air chimney is composed of a novel accumulation material that allows for sensible heat storage. Solar radiation can heat the accumulation layer during the day and the stored energy can be used to preheat the ventilation air. The prototype of the solar chimney was tested in laboratory conditions using a dedicated experimental rig. Furthermore, numerical calculations were performed using TRNSYS software, where a validated dynamic numerical model was developed to simulate the performance of the device. The results show that airflow direction, volume, and the number of heated walls significantly impact the power transferred from the solar chimney walls to the air. The maximum power transferred from the solar chimney walls to the air per unit of surface varied from 360.2 W/m2 (when all walls were heated) to 672.4 W/m2 (when only one wall was heated). The validated model underestimates the outlet air temperature of the solar chimney by a maximum of 0.39 °C on average basis and shows that the increase of air temperature between −10 and 20 °C at 1000 W/m2 determines a decrease of 12.5 % of the thermal output. The obtained results allow one to highlight that the proposed solution can be considered as a replacement for typical brick chimneys located on roofs or as a thermal storage wall.

Dynamic diffusion characteristics of airflow and coal dust during the mining process based on MRF: A numerical simulation study

Turbulence generated by rotation of shearer has a great impact on the distribution of dust. The MRF method of multiple reference frame was employed to simulate airflow and dust distribution during mining process. The distribution of cutting dust under different airflow velocities, cutting speeds, and cutting direction (against or follow the direction of airflow) were compared and analyzed. Results show that the generated cutting dust using MRF method tends to move horizontally and vertically. As the speed of airflow increases, vertical characteristics diminish. Simultaneously, horizontal dissipation rises with the deviation of airflow speed. The increase of rotational speed augments the distance covered by cutting airflow, including vertical offset and windward motion. Moreover, the elevated drum speed amplifies airflow speed in the sidewalk and the primary influence range is approximately 80 m. When cutting in the downwind direction, the airflow exhibits a pronounced vertical and horizontal offset behind the drum. Conversely, when cutting in the upwind direction, these characteristics are less evident, resulting in a more uniform spatial distribution of cutting dust in the downwind direction. The majority of dust generated when cutting against the airflow tends to move in the low-altitude area, contributing to a more disordered pattern.

Experimental study on energy storage characteristics of packed bed using different solid materials

The packed bed energy storage system can solve the mismatch between solar energy supply and demand at a low cost. The physical properties of storage materials have a decisive impact on the performance of storage systems. Different scenarios may require different storage materials. Studying the impact of storage materials on storage characteristics is crucial. However, the comparative analysis and research on different TES materials are focused on characterization and numerical simulation but less on packed bed TES experiments. This paper evaluates the thermal durabilities of three materials, including sintered ore particles, alumina balls, and rock particles, through thermal cycling tests. Through packed bed heat storage experiments, the energy storage characteristics and thermocline evolution characteristics of three beds under different operating conditions are compared and analyzed. The results indicate that all materials exhibit excellent thermal durabilities. A larger bed voidage and smaller bed heat capacity are beneficial for thermal diffusion in the bed. When reverse charging, the natural convection of air in the bed enhances the convective heat transfer effect, resulting in a higher charging power. The existence of natural convection promotes the mixing of cold air and hot air in the tank, increases the irreversibility of the process, and leads to a significantly lower efficiency in reverse flow compared to that in forward flow. When changing the airflow direction, the system overall exergy efficiencies of SOP, alumina, and rock bed decrease from 74.1 %, 72.4 %, and 77.2 % to 47.0 %, 39.9 %, and 45.8 %, respectively. Regardless of the airflow direction, the smaller the bed voidage and the larger the bed heat capacity, the better the maintenance characteristics of the thermocline.

Temperature distribution in the crevasse-drainage systems of the Antarctic glaciers: A case study of the Perunika Glacier

Discovered only about 200 years ago, Antarctica is the poorest and most isolated ecosystem on Earth. Its thinner atmosphere, due to the centrifugal forces of Earth’s rotation, the ozone hole, and stronger solar radiation, creates a natural laboratory that provides information about the state and trajectory of Earth’s climate condition. This study aimed to determine the depth of heat penetration from the surface of the glacier into the crevasses in the ablation zone and establish the zone of constant temperatures in the glacier. It explored the relationship between the air temperature at the glacier surface and the temperature distribution in the crevasses, including the temperature gradient at different levels and the direction of the airflow. We used autonomous data loggers for measuring and recording temperature and relative humidity. The measured depth reached 18 m in the central part of the glacier and 9 m in the periphery. An ultrasonic anemometer was installed in the deepest crevasse in to the center of the glacier to determine the size and direction of air flows. Meteorological parameters such as air temperature, humidity, atmospheric pressure, and solar radiation were measured on-site using autonomous sensors and recording devices mounted on installations on the glacier surface and at depth using alpine techniques. The results show a temperature gradient through 3-meter layers, a relatively clear boundary of the constant temperature zone, and a significant infiltration of cold air through the crevices driven by turbulent wind processes. Additionally, a weak negative correlation was found between solar activity and temperatures in the crevasses. It appears that as solar activity increases, the temperature decreases. There are also weak but consistently positive correlations with air movement both upward and downward. The temperature becomes constant with the increase of the depth until a zone of constant temperatures is determined and the temperature variance becomes insignificant. This zone varies in different crevаsses, meaning it is influenced by the specific characteristics of each crevasse location. At shallow depths, temperature is influenced by external temperature, but with the depth increasing this influence decreases. On windy days, the zone of constant temperature expands. During higher solar activity, air circulation accelerates—both upward and downward. The relationship between solar activity and climatic processes in glacier drainage systems adds new insights to solar-terrestrial physics.

Solar air heater energy and exergy enhancement using a v-corrugated wire mesh absorber: An experimental comparison

In this paper, the energy and exergy performance of a double-pass solar air heater (SAH) using a novel model of a v-corrugated wire mesh absorber (CM-SAH) is investigated experimentally. The v-corrugated wires are adjacent to each other in one layer along the airflow direction to reduce the hydraulic resistance. Simultaneously, this arrangement increases the surface absorptance rate of solar radiation and expands the heat exchange area. To evaluate the performance of CM-SAH, a standard SAH having a v-corrugated absorber plate (CP-SAH) and the same configuration dimensions is compared with CM-SAH. The comparison is achieved under the same operating conditions and using different air mass flow rates of (0.01, 0.02, and 0.03 kg/s). The results show that the CM-SAH outperformed the CP-SAH in terms of thermal efficiency, exergy efficiency, and output air temperature. The maximum thermal efficiencies reach 87.3 % and 65.1 %, while the maximum exergy efficiencies reach 4.4 % and 3.4 %, for CM-SAH and CP-SAH, respectively. In addition, the thermal efficiency of CP-SAH decreased after midday while that of CM-SAH continuously increased.

Investigation of temperature field variations induced by the air thermodynamic behavior when trains pass through a high-speed railway tunnel in cold regions

High-speed railway tunnels in the cold region, whose numbers are increasing, are widely exposed to the threat of frost damage caused by extremely negative temperatures. The operation of high-speed trains has made this problem even more pronounced. But there are fewer studies focusing on the dynamic changes in temperature during train operation. In this paper, the air thermodynamic behavior of trains passing through a tunnel and its consequences were investigated with the help of the CFD method. In numerical simulations, conditions of different natural airflows, different train speeds, different blockage ratios, as well as two trains intersecting in the tunnel were involved. The following valuable results were obtained. In cold environments, train-induced pressure wave effects will affect the air thermodynamic behavior, but the overall trend in air temperature is mainly influenced by the heat transfer between cold and warm air. The high-speed train will lead to massive cold air being carried into the tunnel and some warm air inside being pushed out. Heat transfer between cold and warm air will cause a significant decrease in tunnel air temperature. This air thermodynamic behavior is particularly prominent in the case of large blockage ratios. When there are same-direction natural airflows, they will be coupled with train-induced airflows, causing a greater decrease in tunnel air temperature. In contrast, opposite-direction natural airflows can reduce the negative effects of the train. Taking the case of opposite-direction natural airflow velocity of 5 m/s as an example, the temperature changes of the three cross-sections are only 16.7 %, 14.8 %, and 42.1 % of those in the case of no natural airflow. Whatever the direction of natural airflows, coupling effects between them and train-induced airflows will be more significant as the natural airflow speed increases. Greater train speed means more cold air entering the tunnel and stronger heat transfer between cold and warm air, causing a more significant temperature decrease. When two trains intersect through the tunnel, airflows caused by them will be coupled. As a result, only a little air enters the tunnel from the entrance and exit, and the heat transfer between air with different temperatures is weak. In this case, the air temperature doesn't decrease but slightly increases as the air is compressed.

Experimental and theoretical study on the ceasing motion of a droplet manipulated by air-blowing nozzle

In this study, the dynamic process of a droplet moving with a substrate until blocked by air flow is investigated experimentally and theoretically. A sequence of experiments has been conducted to investigate the impacts of wetting properties, droplet volumes, air flow velocities, and droplet velocities. The substrate is driven by a linear motion motor to ensure the droplet moves at a certain velocity alongside the substrate. The air flow that is vertically injected from the nozzles toward the substrate is known as an impinging jet. After the air flow impacts the substrate, it will blow horizontally. When the direction of air flow is opposite to that of the droplet movement, a force will be exerted on the surface of the droplet. This action incurs the deformation of the droplet and the cessation of its movement, eventually resulting in an equilibrium state. The droplet shape and motion processes are recorded by a high-speed camera. A mathematical model considering the effect of droplet contact angle, droplet size, droplet moving velocity, and air flow velocity is established in the state of equilibrium. Correlation factors are used in the model for the drag coefficient and air average velocity acting on the droplet. It is found that the air flow rate required to stop the motion of the droplet increases with the droplet moving velocity and the droplet size but reduces with the increase in the static contact angle. The mathematical model, when equipped with suitable correlation factors, exhibits good agreement with experimental data and could potentially be utilized as a predictor of critical velocity for the cessation of the droplet motion.

Simulation of ambient temperature and humidity distribution in eight-span greenhouse under different wind conditions and corn height

The greenhouse environment suitable for crop growth usually depends on reasonable ventilation, and outdoor air flow state and indoor crop height are important factors affecting the ventilation effect. This study conducted simulation and experimental research on corn cultivation in an eight-span plastic greenhouse, analyzing the effects of outdoor wind speed, wind direction, and indoor crop height variations on the uniformity of temperature and relative humidity distribution as well as the air flow dynamics within the greenhouse. The study shows that as outdoor wind speed increases from 0.5 m/s to 2.5 m/s, for every 1 m/s increment, temperatures decrease by 2.2 °C and 0.9 °C, respectively. The increase in outdoor wind speed resulted in uniformity of greenhouse temperature and humidity along the vertical height, but exacerbated the degree of inhomogeneity in the east-west direction. The change in outdoor wind direction leads to differences in airflow direction and ventilation volume. On the south side of the greenhouse, while temperature is lower, the relative humidity is higher, with maximum differences in temperature and humidity between the north and south sides being 0.6 °C and 1.5 %, respectively, when the northeast wind blows. The east wind has the best cooling effect. The uneven degree of temperature and humidity distribution in the east and west direction of the greenhouse is positively correlated with crop height. This study can provide valuable insights for adjusting and optimizing natural ventilation strategies in large multi-span greenhouses.

Investigations on thermal profiles and flow structures in a square channel equipped with staggered vortex turbulators

Given the escalating energy demands today, improving the efficiency of engineering equipment is crucial for optimizing energy use. This study focuses on enhancing heat exchanger performance through passive methods, particularly by installing vortex turbulators. Passive techniques can effectively manage energy costs while enhancing efficiency.The research examines thermal profiles and airflow structures within a square channel heat exchanger (SCHE) equipped with staggered vortex turbulators (SVTs). SVTs feature a unique design combining rectangular winglets and V-pattern baffles. The installation of SVTs aims to intensify vortex strength, thereby increasing SCHE efficiency, convective heat transfer coefficients, and overall heat transfer potential. The study investigates the effects of SVT dimensions (b1/H and b2/H), airflow directions (+x and -x), installation patterns (pattern no. 1 and 2), pitch to height ratios (P/H = 1, 1.5, and 2), and flow attack angles (α = 20°, 30°, and 45°). Computational simulations using the finite volume method with a commercial code (FLUENT) under laminar flow conditions (Reynolds number of 100–2000) provide insights into thermal profiles, fluid temperature distributions, and flow configurations within the SCHE. Staggered arrangement and gap spacing are employed to reduce pressure loss and enhance airflow strength. The results highlight flow structures and heat transfer characteristics in the heat exchanger channels, elucidating the underlying mechanisms of the heat exchange process. Understanding these behaviors is crucial for developing more efficient heat exchangers and vortex generators in the future. Simulation findings demonstrate that SVTs significantly enhance convective heat transfer over smooth channels due to increased vortex strength. Notably, pattern no. 2 SVTs (b1/H = b2/H = 0.20) achieve the highest Nu/Nu0 of 19.21 in the +x flow direction at Re = 2000, α = 30°, and P/H = 1. In conclusion, the study identifies a maximum thermal enhancement factor of 4.38. It underscores the potential of pattern no. 2 SVTs for optimizing heat exchanger performance, offering valuable insights for future developments in thermal management technologies.

Personalized air curtain optimized to reduce fine particle exposure in industrial environments with different indoor airflow conditions

Recently, personalized air curtains combined with safety helmets have shown great potential in reducing particle inhalation exposure of workers in industrial settings. In this study, the helmet of the basic air curtain (BA) was optimized. One optimization method was to add a mask to the helmet of the basic air curtain (BAF), and the other optimization method was to add a face shield and sealing cloth to the helmet of the basic air curtain (BAFS). Computational fluid dynamics (CFD) method was used to compare the protective effect (PE) of the air curtain helmets with BA, BAF, and BAFS configurations. The impacts of the air supply velocity (0.05, 0.1, 0.2, 0.3, 0.4, and 0.5 m/s) of the air curtain in a static wind environment, and the direction and speed of the indoor airflow (0.1, 0.3, 0.5, 0.7 and 1 m/s) on the PE of the helmets were also investigated. Results showed that the BAFS helmet had the best respiratory protection, followed by the BAF and the BA helmet, regardless of indoor airflow conditions. The directional diversion effect of the face shield and the bidirectional blocking effect of the sealing cloth strengthened the PE. In the static indoor airflow environment, air supply velocity and helmet configurations had a remarkable impact on the PE. With the increase of the air supply velocity, the PE of the BA and optimized helmets showed S-shape and C-shape trends. When the air supply velocity reached 0.5 m/s, the PE of the BA, BAF, and BAFS helmets were close to 0.844, 0.985, and 1, respectively. In the uniform indoor airflow environments, the PE of the BAFS helmet was close to 1 and was almost undisturbed by the indoor airflow. This work may help inspire the development of respiratory protective equipment to reduce particulate exposure in industrial settings.

Experimental study on heat storage characteristics of an air-sand moving bed heat exchanger

The air-sand moving bed heat exchanger, designed for storing fluctuating medium-temperature gas waste heat, offers significant potential for energy conservation and carbon reduction in industrial settings. However, its operational characteristics are insufficiently explored. This study investigates the heat storage process involving direct contact and cross-flow of air and quartz sand within a rectangular heat exchanger chamber. Comprehensive analyses were conducted to explore flow resistance characteristics, temperature response, and heat storage performance. Results indicate that pressure drop increases with higher air velocity and temperature, and lower air pressure, particle diameter. The relative discrepancy between fitted pressure drops and experimental data is below 10%. The primary heat transfer zone exists during particle descent. As the air-particle mass flow ratio increases, the descent rate of this zone along the airflow direction slows. Additionally, higher air temperatures elevate the optimal air-particle mass flow ratio. With inlet temperatures for air and particles set at 350 °C and 30 °C respectively, and a mass flow ratio of 0.81, an exergy efficiency of 58.93% and a power density of 600.64 kW·m−3 are achieved. These findings offer crucial insights for air-sand moving bed heat exchangers for medium-temperature gas waste heat recovery.

A study on the uniformity of hot air drying quality for stacked flake materials based on multi-physical coupling fields

To improve the uniformity of the hot air drying quality for stacked flake materials, a heat and mass transfer study of stacked flake materials drying process based on multi-physical field coupling is carried out. A numerical simulation model of the stacked flake materials is developed based on the multi-physical field coupling theory, and the accuracy of the numerical simulation model is verified by the bidirectional alternating hot air drying test bed. The segmented hot air drying method is used to analyze the influence mechanism of single airflow direction and alternate airflow direction on the heat and mass transfer for stacked flake materials, and the optimization of drying parameters is studied. The results indicate that a single airflow direction may cause excessive drying, and the uneven stacking density significantly affects the drying quality. The increase of air flow direction change number will lead to the improvement of drying uniformity and moisture content of drying results, and at the same time, the flake material absorbs moisture significantly after changing the air flow direction. By adopting the down-down-up-up airflow direction and optimizing the parameters, the moisture content uniformity of the drying results is improved by 19%, while energy consumption is reduced.

Spray characteristics of elliptical orifice spray in diesel engine under air movement conditions

The development of high-quality mixture is a critical requirement for achieving high-efficiency and low-emission diesel engines, and fuel injection system performance improvement and in-cylinder airflow organization are crucial ways for achieving high-quality mixture. The elliptical nozzle is used as the research object in this research, and numerical simulation is utilized to investigate the effect of different airflow speeds and directions on the atomization characteristics of the elliptical nozzle jet, in order to provide a theoretical basis for the engineering application of the elliptical nozzle in diesel engines. The results show that under the same airflow conditions, the vertical penetration distance of the spray decreases while the horizontal penetration distance increases with the use of elliptical orifices, the surface wave perturbation on the windward side is more violent, and reduce spray field the Sauter Mean Diameter (SMD). The spray projected area grew by 13.5%, the spray SMD dropped by 14.8%, and the vertical penetration distance of the spray with elliptical orifices fell by 18% with an increase in airflow velocity from 0 to 20 m/s. When the airflow direction and the spray direction were at a 90° angle and the SMD was lower than that of the circular orifice by 12.9%. The angle between the airflow direction and the short axis of the elliptical orifice was 30°when the spray projection area was larger, the perturbation of the spray body was more intense, and the surface wave amplitude was larger.

Regional differences in the grain size characteristics of surface sediments from typical barchan dunes in arid zones

The grain size characteristics of aeolian sediments are the combined result of sand sources, regional airflow regimes, dune morphology, etc., and are essential for understanding the formation and evolution of barchan dunes. Based on field investigations and laboratory experimental data, in this paper, we explored differences in the grain size characteristics of the surface sediments of barchan dunes at the southeastern edge of the Taklimakan Desert (TKLM-SE), the western (QB-W) and southern parts of the Qaidam Basin Desert (QB-S), the sand belt connecting the Badain Jaran Desert and the Tengger Desert (BT-B), and their responses to sand sources, dune morphology, and wind regimes. The main results were as follows: (i) The mean grian size distribution patterns of the windward slope toe to the leeward slope toe through the dune crest/ridge varied with different transects of the barchan dunes and different deserts, showing four types including gradually fining (GF), gradually coarsening (GC), coarsening followed by fining (CF), and fining followed by coarsening (FC). The patterns were GF and CF in the TKLM-SE; GF, GC, and FC in the BT-B; GF, GC, and CF in the QB-W; and GF in the QB-S. (ii) The interdune sediments provided the source material for the formation and development of barchan dunes and their grain size varied in different deserts. The interdune sediments were composed of gravel and very fine sand in the TKLM-SE, while they were composed of medium and fine sand in the QB-W, QB-S, and BT-B. (iii) The windward side of the barchans varied with different wind directions, and dune height affected dune surface airflow velocity and direction, changing the pattern of grain size distribution on the dune surface. The wind regime over a ten-day or half-month scale could explain the variance in the grain size distribution patterns better than that on an annual scale. (iv) Grain size characteristics of dune surface sands changed with dune shape due to changes in the surface airflow velocity and direction and the sediment-carrying capacity of the airflow. With an increasing ratio of dune height to dune width, the grain size of the dune crest sands became coarser. These results help advance our understanding of the grain size characteristics of barchan dunes and regional variabilities in their patterns.

Interfacial exchange of airflow and bacteria-carrying particles induced by door opening and foot traffic in an operating room

Maintaining high air cleanliness in operating rooms (ORs) can reduce surgical site infections (SSIs). However, door openings and foot traffic during surgery may allow the intrusion of contaminated air and increase microbial contamination in ORs. In this study, numerical methods were applied to investigate the dynamic airflow and bacteria-carrying particle (BCP) dispersion during sliding door opening and foot traffic in an OR. The door movement and realistic human walking were modeled by the dynamic mesh technique. The interfacial exchange of airflow and BCPs was evaluated as the medical staff entered and exited the OR under fixed supply air temperatures and various differential pressures, respectively. Results showed that walking across the door interface caused a sharp increase in airflow exchange between the OR and the anteroom (ANT). An average walking speed of 1.2 m/s induced a maximum inflow rate of approximately 1.32 times greater when entering the OR than when leaving the OR. Once the door was open, the temperature difference convection effect was more significant than the pressure difference outflow effect. Differential pressure outflow indirectly affected airflow exchange at the door interface by changing the direction and temperature of airflow in the ANT. Whether entering or leaving the OR, the BCP intrusion ratios were on average 1.5 times higher at high pressure differentials (15 and 20 Pa) than at low pressure differentials (5 Pa and 10 Pa). This study is expected to improve the understanding of the impact of door opening and foot traffic on OR air quality during surgery.