AVIRIS Research Articles

Investigation of spectral bands and sensor parameters for methane emission detection imaging spectrometer

Recently, interest has increased in developing remote sensing (RS) sensor systems with a high spatial and spectral resolution for quantifying methane (CH4) emissions from point sources. Evaluating sensor parameters can lead to a better understanding of technological advancements in CH4 emission estimation. This study addresses several important topics, including the robust algorithm for point source CH4 emission detection, selecting optimum CH4 absorption bands and their sensitivity analysis, and evaluating sensor parameters such as spatial and spectral resolution and signal-to-noise ratio (SNR). Since the matched filter algorithm efficiently detects point source emissions with palpable accuracy, it has been used here for the Airborne Visible InfraRed Imaging Spectrometer – Next Generation (AVIRIS-NG) sensor data acquired over the USA. The optimum band selection for CH4 detection was determined using a normalized sensitivity method to investigate the effects of aerosol, water vapor (WV), and surface albedo variations. The impact of these parameters on the CH4 absorption bands in the short-wave infrared (SWIR) range has been analyzed using MODerate resolution atmospheric TRANsmission (MODTRAN) radiative transfer (RT) model simulations. Using AVIRIS-NG data as a testbed, various methods have been used to reconstruct original data and generate data sets with different sensor specifications. The effects of the sensor parameters, such as spatial and spectral resolution and SNR, on the detection accuracy were analyzed. The results show the significance of SNR over the spatial and spectral resolution for better emission detection. It indicates the reasonable selection of sensor parameters that can help to create an optimal sensor system that will ultimately support the development of an imaging spectrometer suitable for CH4 emission estimation.

A Hyperspectral Change Detection (HCD-Net) Framework Based on Double Stream Convolutional Neural Networks and an Attention Module

Human activities and natural phenomena continually transform the Earth’s surface, presenting ongoing challenges to the environment. Therefore, the accurate and timely monitoring and prediction of these alterations are essential for devising effective solutions and mitigating environmental impacts in advance. This study introduces a novel framework, called HCD-Net, for detecting changes using bi-temporal hyperspectral images. HCD-Net is built upon a dual-stream deep feature extraction process, complemented by an attention mechanism. The first stream employs 3D convolution layers and 3D Squeeze-and-Excitation (SE) blocks to extract deep features, while the second stream utilizes 2D convolution and 2D SE blocks for the same purpose. The deep features from both streams are then concatenated and processed through dense layers for decision-making. The performance of HCD-Net is evaluated against existing state-of-the-art change detection methods. For this purpose, the bi-temporal Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) hyperspectral dataset was utilized to assess the change detection performance. The findings indicate that HCD-Net achieves superior accuracy and the lowest false alarm rate among the compared methods, with an overall classification accuracy exceeding 96%, and a kappa coefficient greater than 0.9.

Unsupervised Wavelet-Feature Correlation Ratio Markov Clustering Algorithm for Remotely Sensed Images

The spectrums of one type of object under different conditions have the same features (up, down, protruding, concave) at the same spectral positions, which can be used as primary parameters to evaluate the difference among remotely sensed pixels. The wavelet-feature correlation ratio Markov clustering algorithm (WFCRMCA) for remotely sensed data is proposed based on an accurate description of abrupt spectral features and an optimized Markov clustering in the wavelet feather space. The peak points can be captured and identified by applying a wavelet transform to spectral data. The correlation ratio between two samples is a statistical calculation of the matched peak point positions on the wavelet feature within an adjustable spectrum domain or a range of wavelet scales. The evenly sampled data can be used to create class centers, depending on the correlation ratio threshold at each Markov step, accelerating the clustering speed by avoiding the computation of Euclidean distance for traditional clustering algorithms, such as K-means and ISODATA. Markov clustering applies several strategies, such as a simulated annealing method and gradually shrinking the clustering size, to control the clustering convergence. It can quickly obtain the best class centers at each clustering temperature. The experimental results of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) and Thermal Mapping (TM) data have verified its acceptable clustering accuracy and high convergence velocity.

Noisy band selection based on the integration of the Stacked-Autoencoder and Convolutional Neural Network approaches for hyperspectral data.

The presence of noise on hyperspectral images causes degradation and hinders efficiency of processing for land cover classification. In this sense, removing noise or detecting noisy bands automatically on hyperspectral images becomes a challenge for research in remote sensing. To cope this problem, an integrated model (SAE-1DCNN) is presented in this study, based on Stacked-Autoencoders (SAE) and Convolutional Neural Networks (CNN) algorithms for the selection and exclusion of noisy bands. The proposed model employs convolutional layers to improve the performance of autoencoders focused on discriminating the training data by analyzing the hyperspectral signature of the pixel. Thus, in the SAE-1DCNN model, information can be compressed, and then redundant information can be detected and extracted by taking advantage of the efficiency of the deep architecture based on the convolutional and pooling layers. Hyperspectral data from the AVIRIS (Airborne Visible/Infrared Imaging Spectrometer) sensor were used to evaluate the performance of the proposed automatic method based on feature selection. The results showed effectiveness to identify noisy bands automatically, suggesting that the proposed methodology was found to be promising and can be an alternative to identify noisy bands within the scope of hyperspectral data pre-processing.
 Keywords: noisy bands; feature selection; convolutional neural network; stacked-autoencoders; hyperspectral data

Hydrocarbon Spectra Slope (HYSS): A Spectra Index for Quantifying and Characterizing Hydrocarbon oil on Different Substrates Using Spectra Data

Many sensors in Optical domain allow for detection of hydrocarbons in oil spills study. However, high resolution laboratory and airborne imaging spectrometers have shown potential for quantification and characterization of hydrocarbon. Available methods in literature for quantifying and characterizing hydrocarbons on these data relies mainly on shapes and positions of hydrocarbon key absorption features, mainly at 1.73 µm and 2.30 µm. Shapes formed by these absorption features are often influenced by spectral features of background substrates, thereby limiting the quality of results. Furthermore, multispectral sensors cannot resolve the shapes of key absorption features, a strong limitation for methods used in previous works. In this study, we present Hydrocarbon Spectra Slope (HYSS), a new spectra index that offers predictive quantification and characterization of common hydrocarbon oils. Slope values for the studied hydrocarbon oils enable clear discrimination for relative quantitative analysis of oil abundance classes and qualitative discrimination for common hydrocarbons on common background substrates. Data from ground-based spectrometers and Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) are resampled to AVIRIS, Advanced Space-borne Thermal Emission and Reflection Radiometer (ASTER) and LANDSAT 7 Enhanced Thematic Mapper’s (ETM+) Full Width at Half Maximum (FWHM), in order to compute spectra slope values for hydrocarbon abundance /hydrocarbon-substrate characterization. Despite limitations of nonconformity of central wavelengths and/or band widths of multispectral sensors to key hydrocarbon band, statistical significance for both quantitative and qualitative analysis at 95% confidence level (P-value ˂0.01) suggests strong potential of the use of HYSS, multispectral and hyperspectral sensors as emergency response tools for hydrocarbon mapping.

Region Expansion of a Hyperspectral-Based Mineral Map Using Random Forest Classification with Multispectral Data

Observation images from hyperspectral (HS) sensors on satellites and aircraft can be used to map minerals in greater detail than those from multispectral (MS) sensors. However, the coverage of HS images is much less than that of MS images, so there are often cases where MS images cover the entire area of interest while HS images cover only a part of it. In this study, we propose a new method to more reasonably expand the mineral map of an HS image with an MS image in such cases. The method uses various mineral indices from the MS image and MS sensor’s band values as the input and HS image-based mineral classes as the output. Random forest (RF) two-class classification is then applied iteratively to determine the distribution of each mineral in turn, starting with the minerals that are most consistent with the HS image-based mineral map. The method also involves the correction of misalignment between HS and MS images and the selection of input variables by RF multiclass classification. The method was evaluated in comparison with other methods in the Cuprite area, Nevada, using the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) and Hyperspectral Imager Suite (HISUI) as HS sensors and the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) as MS sensors. As a result, all of the evaluated region-expansion methods with an HS–MS image pair, including the proposed method, showed better performance than the method using only an MS image. The proposed method had the highest performance, and the inter-mineral averages of the F1-scores for the overlap and non-overlap areas were 85.98% and 46.46% for the AVIRIS–ASTER image pair and 82.78% and 42.60% for the HISUI–ASTER image pair, respectively. Although the performance in the non-overlap region was lower than in the overlap region, the method showed high precision and high accuracy for almost all minerals, including minerals with only a few pixels. Misalignment between the HS–MS images is a factor that degrades accuracy and requires precise alignment, but the misalignment correction in the proposed method could suppress the effect of misalignment. Validation studies using different regions and different sensors will be carried out in the future.

A novel method for detecting soil salinity using AVIRIS-NG imaging spectroscopy and ensemble machine learning

Soil salinization is one of the major land degradation processes spread over millions of hectares of global land. Hyperspectral Remote Sensing (HRS) coupled with modern data mining approaches help in real-time and cost-effective assessment or monitoring of salt-affected soils. This study aimed at predicting soil salinity across five sites in India using the Airborne Visible-Infrared Imaging Spectrometer - Next Generation (AVIRIS-NG) data in low to moderately salt-affected cropland soils. We have identified four unique spectral absorption features having sensitivity towards soil salinity through a hybrid feature selection algorithm. Soil electrical conductivity (EC) was estimated using different machine learning (ML) based models such as random forest (RF), gradient boosting machines (GBM), and deep learning (DL). An ensemble of RF and DL models showed the best performance with the coefficient of determination (R2) of 0.89 and 0.55 and normalized root-mean-squared error of 0.15 and 0.16 in training and test datasets, respectively. We also proposed a new hyperspectral soil salinity index using Shannon entropy-based aggregation of selected absorption features. The newly proposed index outperformed other majorly used remote sensing-based salinity indices. It also showed a strong correlation with measured EC (r = 0.68) and ML-predicted soil EC (r = 0.78), both being significant at 1% level of significance. The index was effective in classifying HRS images into six distinct salinity classes. We also assessed the feasibility of applying the proposed salinity index for future hyperspectral missions through the simulation of various spectral-spatial resampling scenarios and estimated the optimal spectral and spatial resolution for salinity prediction. The hyperspectral salinity index can be directly estimated from HRS data without the need for time-consuming and expensive field samplings and used as a proxy to evaluate soil salinity status under field conditions.

Examining effect of super-resolution on AVIRIS-NG data: A precursor to generation of large-scale urban material and natural cover maps

The two-phase Airborne Visible InfraRed Imaging Spectrometer – Next Generation (AVIRIS-NG) campaign over India has generated datasets of numerous natural and artificial surroundings with high signal-to-noise ratios and higher spatial and spectral consistencies. However, the first phase AVIRIS-NG datasets of urban areas have 8.1 m spatial resolution, which is insufficient for producing level-4 urban material and natural cover maps required to model Earth’s processes at the micro-scale or constantly monitor urban processes. The current work addresses this drawback by demonstrating a part of the proposed proof-of-concept approach on the AVIRIS-NG dataset of Ahmedabad, India, wherein super-resolution (SR) is proposed to enhance the hyperspectral image’s spatial resolution and preserve its rich spectral content at the targeted spatial scale before utilizing it for producing detailed urban land cover maps. A step-wise account of the SR process has been provided herein to aid the reader in reproducing these experiments. Super-resolved products generated using four SR algorithms have been compared and validated using a composite framework based on processing time, qualitative visual investigation of selected image patches and spectral profiles, re-interpretation of Wald’s reduced resolution protocol and full-reference image quality metrics. Results suggest the AVIRIS-NG dataset’s successful spectral and spatial fidelity at a larger spatial scale, albeit varying in each super-resolved output. Sparse regression and natural prior (SRP), and anchored neighbourhood regression (ANR) produce the best and poorest super-resolved outputs among the tested SR algorithms. Although gradient profile prior (GPP) generated super-resolved product is the second best, it is also the most computationally expensive algorithm. An additional yardstick in the form of a spectral similarity analysis of randomly selected unknown spectral signatures on super-resolved output against a reference spectral library has been proposed to ascertain spectral content preservation further before utilizing the super-resolved product for urban information extraction. This exercise’s findings reveal the presence of the target urban land cover feature at the unknown pixels with matching scores of greater than 0.5 in both best and worst super-resolved products, thereby advocating the extension of the proposed proof-of-concept to recently launched spaceborne hyperspectral missions’ datasets.

Satellite Image Processing Using Radiometric Resolution & Spectral Resolution

Abstract: This paper presents a detailed comparison of various image processing techniques for analysing satellite images. The satellite images are large in size, acquired from long distances and are affected by noise and other environmental conditions. Hence it is necessary to process them so that they can be used by the researchers for analysis. Spectral resolution basically is to measure changes in things that impact our environments like water quality or vegetation etc. Satellite images are widely used in many real time applications such as in agriculture land detection, navigation and in geographical information systems. In this paper, a review of spectral resolution requirements for urban mapping evaluated how spectral resolution of high-spatial resolution optical remote sensing data influences detailed mapping of urban land cover. A comprehensive regional spectral library and low altitude data from the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) were used to characterize the spectral properties of urban land cover.

Automatic detection of thin oil films on water surfaces in ultraviolet imagery

AbstractAmong the various remote sensing technologies that have been applied to monitor oil spills on the sea surface, passive ultraviolet (UV) imaging is a controversial one that has raised some disputes in the community of oil spill remote sensing. As a result, the research and applications of oil spill detection using passive UV imaging have not been as developed as other methods. In order to clarify some existing questions on oil spill detection using passive UV remote sensing technology, this paper discusses the needs of thin oil film detection, examines the feasibility of thin oil film detection using passive UV imaging through field experiments under controlled conditions and validates it with the UV imagery derived from the airborne visible/infrared imaging spectrometer (AVIRIS) observation of the Deepwater Horizon oil spill. Two types of fully automatic models are designed to extract the thin oil films on the water surface: (1) a binary classification model based on an adaptive threshold; (2) an unsupervised image segmentation model based on image clustering and greyscale histogram analysis. The two models are tested on the UV imagery obtained through both field experiments and AVIRIS observations. The results indicate that the binary classification model can extract the thin oil films with reasonable accuracy under stable imaging conditions, while the unsupervised image clustering model can robustly detect the thin oil films at the cost of higher computational complexity. These results infer that passive UV imaging is an effective way to detect thin oil films and could be applied to provide early warning at the beginning stage of oil spills and reduce further damage. It may also be applied as a supplementary method for oil spill detection to achieve comprehensive oil spill monitoring.

Radiometric calibration of AVIRIS-NG sensor using Indian desert sites

This manuscript describes reflectance-based vicarious calibration exercise of the Airborne Visible InfraRed Imaging Spectrometer - Next Generation (AVIRIS-NG) sensor during its second phase of observation campaigns over the Indian subcontinent. Vicarious calibration methods are one of the significant approaches that have been practiced successfully for the absolute radiometric calibration of various spaceborne and airborne sensors to ascertain its desired performance in terms of data quality and its accuracy. Calibration campaigns were performed for AVIRIS-NG sensor during its phase-2 campaign overpass at the Desalpar (25th March 2018) and Amarapur (27th March 2018) calibration sites of Gujarat, India. Results from ground-based measurements of atmospheric conditions and surface reflectance including descriptions of the test sites are summarized in this work. Based on the in-situ data and images from the AVIRIS-NG sensor, the at-sensor apparent radiances are simulated using the 6SV radiative transfer model. The comparison shows good agreement between AVIRIS-NG measured radiance and 6SV simulated apparent radiance at the two calibration sites using desert aerosol model. The gains (spectrally) derived agree to within ∼ 2 % each other. Furthermore, an analysis is performed to determine or identify systematic and random errors, and the overall uncertainty is evaluated for reflectance-based method (total uncertainty of less than 4 % spectrally).

Simulating Global Dynamic Surface Reflectances for Imaging Spectroscopy Spaceborne Missions: LPJ‐PROSAIL

AbstractSpectroscopic reflectance data provide novel information on the properties of the Earth's terrestrial and aquatic surfaces. Until recently, imaging spectroscopy missions were dependent mainly on airborne instruments, such as the Next Generation Airborne Visible InfraRed Imaging Spectrometer (AVIRIS‐NG), providing limited spatial and temporal observations. Currently, there is an emergence of spaceborne imaging spectroscopy missions, which require advances in end‐to‐end model support for traceability studies. To provide this support, the LPJ‐wsl dynamic global vegetation model is coupled with the canopy radiative transfer model, PROSAIL, to generate global, gridded, daily visible to shortwave infrared (VSWIR) spectra (400–2,500 nm). LPJ‐wsl variables are cross‐walked to meet required PROSAIL parameters, which include leaf structure, chlorophyll a + b, brown pigment, equivalent water thickness, and dry matter content. Simulated spectra are compared to a boreal forest site, a temperate forest, managed grassland, a dryland and a tropical forest site using reflectance data from tower‐mounted, aircraft, and spaceborne imagers. We find that canopy nitrogen and leaf‐area index are the most uncertain variables in translating LPJ‐wsl to PROSAIL parameters but at first order, LPJ‐PROSAIL successfully simulates surface reflectance dynamics. Future work will optimize functional relationships required for improving PROSAIL parameters and include the development of the LPJ‐model to represent improvements in leaf water content and canopy nitrogen. The LPJ‐PROSAIL model is intended to support missions such as NASA's Surface Biology and Geology and subsequent modeled products related to the carbon cycle and hydrology.

Hyperspectral Remote Sensing Image Synthesis Based on Implicit Neural Spectral Mixing Models

Hyperspectral image (HSI) synthesis, as an emerging research topic, is of great value in overcoming sensor limitations and achieving low-cost acquisition of high-resolution remote sensing HSIs. However, the linear spectral mixing model used in recent studies oversimplifies the real-world hyperspectral imaging process, making it difficult to effectively model the imaging noise and multiple reflections of the object spectrum. As a prerequisite for hyperspectral data synthesis, accurate modeling of nonlinear spectral mixtures has long been a challenge. Considering the above difficulties, we propose a novel method for modeling nonlinear spectral mixtures based on implicit neural representations (INRs) in this article. The proposed method learns from INR and adaptively implements different mixture models for each pixel according to their spectral signature and surrounding environment. Based on the above neural mixing model, we also propose a new method for HSI synthesis. Given an RGB image as input, our method can generate an accurate and physically meaningful HSI. As a set of by-products, our method can also generate subpixel-level spectral abundance as well as the solar atmosphere signature. The whole framework is trained end-to-end in a self-supervised manner. We constructed a new dataset for HSI synthesis based on a wide range of Airborne Visible Infrared Imaging Spectrometer (AVIRIS) data. Our method achieves a mean peak signal-to-noise ratio (MPSNR) of 52.36 dB and outperforms other state-of-the-art hyperspectral synthesis methods. Finally, our method shows great benefits to downstream data-driven applications. With the HSIs and abundance directly generated from low-cost RGB images, the proposed method improves the accuracy of HSI classification tasks by a large margin, particularly for those with limited training samples.

Correction of multi-scale sunglint reflections from the water surface in airborne high-spatial resolution optical images.

Airborne optical images (AOI) are often with complex sunglint reflections, which brings a certain influence to watercolor retrieval. This includes the sunglint reflection with water surface statistical distribution characteristics caused by imaging viewing angles differences, with high spatial resolution surface discrete characteristics sharing similar viewing angles, and the surface Fresnel reflection sunglint differences caused by the skylight difference during the flight of unmanned aerial vehicles. Aiming at the multiscale optical characteristics of sunglint reflection in high spatial resolution AOI, based on multi-path optical radiation transmission, the sunglint reflection interference from three different imaging processes is clarified. We developed a correction method to eliminate these different sunglint reflections on water surfaces and improve the reflectivity accuracy. The comparison with the in situ measured remote sensing reflectance of water indicated that the root mean square error (RMSE) was reduced from 0.0009 sr-1 to 0.0004 sr-1, and the mean relative error (MRE) decreased from 21.8% to 15.7%. This method has also been applied to correct the Airborne Visible Infrared Imaging Spectrometer (AVIRIS) images, showing good applicability. The method is fast, effective, and without auxiliary parameters, which provides a correction reference for different surface sunglint corrections of various AOI.

Multi-label sub-pixel classification of red and black soil over sparse vegetative areas using AVIRIS-NG airborne hyperspectral image

The limited spatial resolution of the hyperspectral (Hx) images corrupts the spectral information of pure materials and their distribution in an image. The accuracy of characterising or classifying the soil using Hx or Mx images decreases when surfaces are covered by vegetation. In the presence of vegetation, a single pixel can be labelled as either vegetation or a specific soil type. In this context, we have studied the usefulness of the multi-label classification (MLC) approach to classify the soil colour in the presence of vegetation cover. We have evaluated its performance on airborne Hx (Airborne Visible InfraRed Imaging Spectrometer - Next Generation, AVIRIS-NG) images acquired over Berambadi catchment, Karnataka, India. The potential of MLC to classify soil types using simulated Sentinel-2 images (Sen-S) was also explored in this study. The surface soil colour in the Berambadi catchment was classified into two soil types (“black” and “red” soils). The proposed MLC approach consists of (1) simulating the mixed spectra of vegetation, red soil, black soil and non-photosynthesis-vegetation (NPV) using linear-mixture-model (LMM) and bi-linear-mixture-model (BLM) to generate a well-balanced calibration data set, and (2) labelling of each pixel into multiple classes using MLC approaches. Performances of classical and deep-neural-network (DNN) based MLC models were compared to identify the best performing model. Our results showed significant performance for the cost-sensitive-multi-label-embedding (CLEMS) model when applied to both AVIRIS-NG (OA=97%) and Sen-S (OA=93%) images. The proposed method requires a limited number of ground-truth samples, and it is operationally practical for large Hx and Mx images.

Monitoring Asbestos Mine Remediation Using Airborne Hyperspectral Imaging System: A Case Study of Jefferson Lake Mine, US

This study investigated an asbestos mine restoration project using Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) hyperspectral data. The distribution of an abandoned asbestos mine (AAM) and treatment area were analyzed before and after the remediation based on the spectral indices for detecting naturally occurring asbestos (NOA) indicators and encapsulation. The spectral indices were developed for NOA, host rock, and encapsulation by logistic regression models using spectral bands extracted from the random forest algorithm. The detection models mostly used VNIR spectra rather than SWIR and were statistically significant. The overall accuracy of the detection models was approximately 84%. Notably, the detection accuracy of non-treated and treated areas was increased to about 96%, excluding the host rock index. The NOA index detected asbestos in the mine area as well as those in outcrops outside of the mine. It has been confirmed that the NOA index can be efficiently applied to all cases of asbestos occurrence. The remote sensing data revealed that the mine area was increased by ~5% by the remediation, and the treatment activity reduced asbestos exposure by ~32%. Moreover, the integrative visualization between the detection results and 3D high-resolution images provided an intuitive and realistic understanding of the reclamation project.

Comparing airborne algorithms for greenhouse gas flux measurements over the Alberta oil sands

Abstract. To combat global warming, Canada has committed to reducing greenhouse gases to be (GHGs) 40 %–45 % below 2005 emission levels by 2025. Monitoring emissions and deriving accurate inventories are essential to reaching these goals. Airborne methods can provide regional and area source measurements with small error if ideal conditions for sampling are met. In this study, two airborne mass-balance box-flight algorithms were compared to assess the extent of their agreement and their performance under various conditions. The Scientific Aviation's (SciAv) Gaussian algorithm and the Environment and Climate Change Canada's top-down emission rate retrieval algorithm (TERRA) were applied to data from five samples. Estimates were compared using standard procedures, by systematically testing other method fits, and by investigating the effects on the estimates when method assumptions were not met. Results indicate that in standard scenarios the SciAv and TERRA mass-balance box-flight methods produce similar estimates that agree (3 %–25 %) within algorithm uncertainties (4 %–34 %). Implementing a sample-specific surface extrapolation procedure for the SciAv algorithm may improve emission estimation. Algorithms disagreed when non-ideal conditions occurred (i.e., under non-stationary atmospheric conditions). Overall, the results provide confidence in the box-flight methods and indicate that emissions estimates are not overly sensitive to the choice of algorithm but demonstrate that fundamental algorithm assumptions should be assessed for each flight. Using a different method, the Airborne Visible InfraRed Imaging Spectrometer – Next Generation (AVIRIS-NG) independently mapped individual plumes with emissions 5 times larger than the source SciAv sampled three days later. The range in estimates highlights the utility of increased sampling to get a more complete understanding of the temporal variability of emissions and to identify emission sources within facilities. In addition, hourly on-site activity data would provide insight to the observed temporal variability in emissions and make a comparison to reported emissions more straightforward.

Evaluation of machine learning techniques with AVIRIS-NG dataset in the identification and mapping of minerals

Identifying valuable mineral resources is obligatory for human development and survival due to their scientific and economic implications. Hyperspectral Remote Sensing (HRS) is an efficient technique that empowers us to precisely identify and map altered minerals based on spectral absorption curves in the VNIR and SWIR range of the electromagnetic spectrum. Machine Learning Algorithms (MLAs) are a subclass of Artificial Intelligence (AI) that improves and automate HRS based lithological mapping using spectra based classification approach. The present study evaluates various MLAs in identifying and mapping hydrothermally altered and weathered minerals such as kaolinite, talc, kaosmec, and montmorillonite. The study was performed with the Airborne Visible Infrared Imaging Spectrometer- Next Generation (AVIRIS-NG) hyperspectral dataset of Jahazpur town of Bhilwara district in the state of Rajasthan, India (75° 9′ 57′' E, 25° 32′ 24″ N). The Spectral Angle Mapper (SAM) algorithm was applied to create a reference mineral distribution map for the target mineral classes. Further, the reference map has been verified with the field validation survey. A total of 828 pixels were identified as end member pixels. The obtained endmember pixels were further used for developing predictive machine learning based models for mapping the mineral resources using eight supervised classifiers, namely Support Vector Machine, k-Nearest Neighbor, Decision Tree, Random Forest, Logistic Regression, Artificial Neural Network, Linear Discriminant Analysis, and Naïve Bayes. The performance of the classifiers was measured using the kappa coefficient, overall accuracy, precision, recall, F1-score, Matthews’s correlation coefficient, and ROC curve. It was observed in the study that the Support Vector Machine outperformed all the classifiers in terms of overall accuracy and AVIRIS-NG data poses an excellent potential for mineral mapping using machine learning based models in a diverse mountainous area.

Airborne imaging spectrometer dataset for spectral characterization and predictive mineral mapping using sub-pixel based classifier in parts of Udaipur, Rajasthan, India

Imaging spectroscopy is used for the mapping of different minerals using their characteristics absorption depths. The present study covers the parts of the Udaipur region for mineral mapping with the help of a Mixture Tuned Matched Filtering (MTMF) soft classifier using the Airborne Visible Infrared Imaging Spectrometer – Next Generation dataset. The preprocessed and classified dataset by MTMF soft classifier identified carbonates, serpentine minerals, and alteration products of ultramafics, clay and mica minerals, and intimate mixture of kaolinite and muscovite in the region. These minerals show the characteristic absorption features at different wavelength positions of the SWIR region. The comparison of the image spectrum was carried out with the reference (mineral library) and laboratory collected reflectance spectral curves. The derived mineral map accurately mapped the minerals and discriminated the minerals belonging to a similar mineral class. Validation was done using field evidences, photomicrographs, XRD, laboratory spectral curves, and already published maps. The accuracy for the generated mineral map is 83.93%.

Crop type discrimination using Geo-Stat Endmember extraction and machine learning algorithms

The identification of crop diversity in today's world is very crucial to ensure adaptation of the crop with changing climate for better productivity as well as food security. Towards this, Hyperspectral Remote Sensing (HRS) is an efficient technique that offers the opportunity to discriminate crop types based on morphological as well as physiological features due to availability of contiguous spectral bands. The current work utilized the benefits of Airborne Visible Infrared Imaging Spectrometer- New Generation (AVIRIS-NG) data and explored the techniques for classification and identification of crop types. The endmembers were identified using the Geo-Stat Endmember Extraction (GSEE) algorithm for pure pixels identification and to generate the spectral library of the different crop types. Spectral feature comparison was done among AVIRIS-NG, Analytical Spectral Device (ASD)-Spectroradiometer and Continuum Removed (CR) spectra. The best-fit spectra obtained with the Reference ASD-Spectroradiometer and Pure Pixel spectral library were then used for crop discrimination using the ten supervised classifiers namely Spectral Angle Mapper (SAM), Spectral Information Divergence (SID), Support Vector Machine (SVM), Minimum Distance Classifier (MDC), Binary Encoding, deep learning-based Convolution Neural Network (CNN) and different algorithms of Ensemble learning such as Tree Bag, AdaBoost (Adaptive Boosting), Discriminant and RUSBoost (Random Under Sampling). In total, nine crop types were identified, namely, wheat, maize, tobacco, sorghum, linseed, castor, pigeon pea, fennel and chickpea. The performance evaluation of the classifiers was made using various metrics like Overall Accuracy, Kappa Coefficient, Precision, Recall and F1 score. The classifier 2D-CNN was found to be the best with Overall Accuracy, Kappa Coefficient, Precision, Recall and F1 score values of 89.065 %, 0.871, 87.565%, 89.541% and 88.678% respectively. The output of this work can be utilized for large scale mapping of crop types at the species level in a short interval of time with high accuracy.