Agricultural Plastic Film Research Articles

Adsorption behavior of nano polyethylene for bensulfuron-methyl in an aqueous environment

Agricultural plastic film, which is widely used to maintain heat and moisture during agricultural production, could gradually degrade into micro- and nano-scale polyethylene plastic fragments when not properly treated. The polyethylene plastic fragments, with ideal properties to carry hydrophobic compounds, interact with pesticide molecules, forming co-exposed residues that persist in the environment. In this work, a small and representative nano-polyethylene particle (PE-NPs, 500 nm) were selected as the adsorption carrier, and bensulfuron-methyl, a commonly used herbicide for crops (e.g. rice and wheat) covered under agricultural plastic films, was chosen as the target analyte to investigate their adsorption behavior. The adsorption equilibrium time of bensulfuron-methyl on PE-NPs increases(6–12 h) with the increase of plastic dosage(500 mg/L-2000 mg/L). The adsorption capacity showed an increasing and then decreasing trend as the dosage of plastic increased, with the highest value achieved at around 500 mg/L. The adsorption behavior was influenced by environmental factors, for example, adsorption was significantly inhibited at pH=9.0 or NaCl concentrations above 0.05 mg/g or dissolved organic matter (oxalic acid) concentrations above 10 mg/L. In addition, The adsorption of bensulfuron-methyl aligned relatively close with pseudo-secondary kinetics and the Freundlich model, suggesting that surface adsorption, intraparticle diffusion, and mass transfer might play a role in the process of non-uniform multilayer adsorption. The adsorption thermodynamics experiment indicated that the adsorption process was spontaneous, heat-absorbing, and mainly physisorption.

The Influence of Rural Ecological Environment Development by China's Industrialization Process

This article aims to solve the problem of heavy pollution load in rural ecological environment at present. This article elaborates on the relevant concepts and theories of rural industrialization and ecological environment protection, mainly using a combination of qualitative and quantitative methods to analyze the current situation of rural ecological environment pollution in the research area. The research results indicate that the current rural ecological environment pollution load in China is heavy and severe, especially the use of fertilizers, pesticides, agricultural plastic films, livestock and poultry breeding, rural life, and township enterprise production, which have caused varying degrees of harm to the regional rural ecological environment. Therefore, effective measures must be taken to achieve the organic combination of rural industrialization and ecological environment protection. This article provides guidance for promoting the optimization and upgrading of rural industrial structure, achieving a win-win situation of economic and ecological benefits.

Enhancing soil gross nitrogen transformation through regulation of microbial nitrogen-cycling genes by biodegradable microplastics

Microplastics (MPs) in agricultural plastic film mulching system changes microbial functions and nutrient dynamics in soils. However, how biodegradable MPs impact the soil gross nitrogen (N) transformations and crop N uptake remain significantly unknown. In this study, we conducted a paired labeling 15N tracer experiment and microbial N-cycling gene analysis to investigate the dynamics and mechanisms of soil gross N transformation processes in soils amended with conventional (polyethylene, PE) and biodegradable (polybutylene adipate co-terephthalate, PBAT) MPs at concentrations of 0 %, 0.5 %, and 2 % (w/w). The biodegradable MPs-amended soils showed higher gross N mineralization rates (0.5–16 times) and plant N uptake rates (16–32 %) than soils without MPs (CK) and with conventional MPs. The MPs (both PE and PBAT) with high concentration (2 %) increased gross N mineralization rates compared to low concentration (0.5 %). Compare to CK, MPs decreased the soil gross nitrification rates, except for PBAT with 2 % concentration; while PE with 0.5 % concentration and PBAT with 2 % concentration increased but PBAT with 0.5 % concentration decreased the gross N immobilization rates significantly. The results indicated that there were both a concentration effect and a material effect of MPs on soil gross N transformations. Biodegradable MPs increased N-cycling gene abundance by 60–103 %; while there was no difference in the abundance of total N-cycling genes between soils without MPs and with conventional MPs. In summary, biodegradable MPs increased N cycling gene abundance by providing enriched nutrient substrates and enhancing microbial biomass, thereby promoting gross N transformation processes and maize N uptake in short-term. These findings provide insights into the potential consequences associated with the exposure of biodegradable MPs, particularly their impact on soil N cycling processes.

Recognition of Plastic Film in Terrain-Fragmented Areas Based on Drone Visible Light Images

In order to meet the growing demand for food and achieve food security development goals, contemporary agriculture increasingly depends on plastic coverings such as agricultural plastic films. The remote sensing-based identification of these plastic films has gradually become a necessary tool for agricultural production management and soil pollution prevention. Addressing the challenges posed by the complex terrain and fragmented land parcels in karst mountainous regions, as well as the frequent presence of cloudy and foggy weather conditions, the extraction efficacy of mulching films is compromised. This study utilized a DJI Mavic 2 Pro UAV to capture visible light images in an area with complex terrain features such as peaks and valleys. A plastic film sample dataset was constructed, and the U-Net deep learning model parameters integrated into ArcGIS Pro were continuously modified and optimized to achieve precise plastic film identification. The results are as follows: (1) Sample quantity significantly affects recognition performance. When the sample size is 800, the accuracy of plastic film extraction notably improves, with area accuracy reaching 91%, a patch quantity accuracy of 96.38%, and an IOU and F1-score of 85.89% and 94.20%, respectively, compared to the precision achieved with a sample size of 300; (2) Different learning rates, batch sizes, and iteration numbers have a certain impact on the training effectiveness of the U-Net model. The most suitable model parameters improved the training effectiveness, with the highest training accuracy achieved at a learning rate of 0.001, a batch size of 10, and 25 iterations; (3) Comparative experiments with the Support Vector Machine (SVM) model validate the suitability of U-Net model parameters and sample datasets for precise identification in rugged terrains with fragmented spatial distribution, particularly in karst mountainous regions. This underscores the applicability of the U-Net model in recognizing plastic film coverings in karst mountainous regions, offering valuable insights for agricultural environmental health assessment and green planting management in farmlands.

Occurrence and potential risks of organophosphate esters in agricultural soils: A case study of Fuzhou City, Southeast China

Fifty agricultural soil samples collected from Fuzhou, southeast China, were first investigated for the occurrence, distribution, and potential risks of twelve organophosphate esters (OPEs). The total concentration of OPEs (ΣOPEs) in soil ranged from 1.33 to 96.5 ng/g dry weight (dw), with an average value of 17.1 ng/g dw. Especially, halogenated-OPEs were the predominant group with a mean level of 9.75 ng/g dw, and tris(1-chloro-2-propyl) phosphate (TCIPP) was the most abundant OPEs, accounting for 51.1% of ΣOPEs. The concentrations of TCIPP and ∑OPEs were found to be significantly higher (P < 0.05) in soils of urban areas than those in suburban areas. In addition, the use of agricultural plastic films and total organic carbon had a positive effect on the occurrence of OPE in this study. The positive matrix factorization model suggested complex sources of OPEs in agricultural soils from Fuzhou. The ecological risk assessment demonstrated that tricresyl phosphate presented a medium risk to land-based organisms (0.1 ≤ risk quotient < 1.0). Nevertheless, the carcinogenic and non-carcinogenic risks for human exposure to OPEs through soil ingestion and dermal absorption were negligible. These findings would facilitate further investigations into the pollution management and risk control of OPEs.

Occurrence Characteristics of Microplastics in Multi-environmental Media and Bellamya aeruginosa of Manao River

Microplastic pollution poses threats to aquatic ecosystems and human health. In this study, in order to investigate the characteristics of microplastic occurrence in different environmental media, the abundance, particle size, shape, color, and composition types of microplastics in the water column, sediment, riparian zone soil, and the benthic snail Bellamya aeruginosa of the Manao River were analyzed using field sampling, microscopic observation, and Fourier infrared spectroscopy. The results showed that the average abundance of microplastics in the surface water of the Manao River was (5.9±0.26) n·L-1; the abundance of microplastics in the upper sediment (by dry weight) was (1.35±0.1) n·g-1, and that in the lower sediment (by dry weight) was (0.93±0.12) n·g-1. The abundance of microplastics in the near riparian zone soil (by dry weight) was (0.68±0.16) n·g-1, and that in the far riparian zone soil (by dry weight) was (0.69±0.14) n·g-1, and the abundance of microplastics in the B. aeruginosa was (2.06±0.25) n·g-1. The analysis results showed that the abundance of microplastics in the upper and lower sediments were positively correlated; the abundance of microplastics in B. aeruginosa was positively correlated with the abundance of microplastics in the upper and lower sediments, respectively; and the abundance of microplastics in the near and far riparian zone soils were also correlated. Most of the microplastics within each environmental medium and B. aeruginosa were <0.1 mm in size, mainly in the form of fibers and fragments, mainly blue and black in color, and mainly composed of polypropylene (PP) and polyethylene (PE). It was found that microplastics in riparian zone soils mainly originated from the fragmentation and decomposition of agricultural plastic films. The results of this study shed light on the accumulation of microplastics in macrobenthic organisms through the investigation of microplastics in multi-environmental media and in the B. aeruginosa, which helps us to understand the potential ecological risk of microplastics in a comprehensive manner.

Selecting reasonable soil moisture-maintaining measures to improve the soil physicochemical properties and achieve high yield and quality of purple garlic in the China Hexi Corridor oasis agricultural area.

Agricultural plastic film, as an important agricultural production material in the China Hexi Corridor oasis agricultural area, is widely used in the intensive production process of purple garlic, which plays an important role in increasing yield, improving quality, ensuring supply, etc. However, the difference in decomposition characteristics between ordinary plastic film and degradable plastic film may affect soil moisture and temperature, thereby affecting soil biochemical properties. Therefore, we conducted a study to solve this problem. Specifically, in the Minle area of the Hexi Corridor, we selected 10 moisture-maintaining measures of ordinary transparent plastic film, transparent oxo-biodegradable plastic film (50-, 80-, and 110-day induction period), ordinary black plastic film, black oxo-biodegradable plastic film (50-, 80-, and 110-day induction period), wheat straw, and aubergine-super absorbent polymers and used the traditional open field without super absorbent polymers as a control. To analyze the effects of different moisture-maintaining measures on soil quality, garlic yield and quality, and water-fertilizer productivity in purple garlic farmland, and conduct a comprehensive evaluation of moisture-maintaining measures using principal component analysis. The results showed that all the moisture-maintaining measures could increase garlic yield, improve bulb quality and water-fertilizer productivity, improve the soil hydrothermal conditions, maintain soil fertility, increase the microbial quantity, and improve enzyme activity. Overall, transparent plastic film mulching was superior to black plastic film mulching, straw mulching, and A-SAP, with 110-day transparent oxo-biodegradable plastic film mulching being the most effective, and was not significantly different from the ordinary transparent plastic film. Compared with other moisture-maintaining measures, the yield, water productivity, irrigation water productivity, and nitrogen fertilizer partial factor productivity of purple garlic were significantly increased by 13.33% to 119.77%, 13.81% to 126.77%, 13.41% to 119.95%, and 13.33% to 119.76%, respectively. Meanwhile, the contents of allicin, soluble sugar, soluble protein, crude fiber, and amino acid content were increased by 1.44% to 14.66%, 4.64% to 36.46%, 0.38% to 28.27%, 1.89% to 26.29%, and 0.38% to 3.74%, and, due to the prolongation of oxo-biodegradable plastic film induction period, the soil microbial community changes from "fungi type" to "bacterium type," reducing the occurrence of soil diseases and improving soil quality. On the basis of the Technique for Order Preference by Similarity to an Ideal Solution (TOPSIS) method, the soil quality was evaluated, and the yield, quality, and water productivity of garlic were comprehensively evaluated under each moisture-maintaining measure using principal component analysis. It was determined that the best soil quality and better bulb quality as well as higher garlic yield and water productivity were obtained when using the 110-day induction period transparent oxo-biodegradable plastic film. It can be used as a more reasonable moisture-maintaining measure and technical reference for the purple garlic industry in the China Hexi Corridor oasis agricultural area, which can ensure the improvement of quality and stabilization of yield and also solve the risk of environmental pollution caused by plastic film mulching at the source.

Machine learning-assisted assessment of key meteorological and crop factors affecting historical mulch pollution in China

Degraded mulch pollution is of a great concern for agricultural soils. Although numerous studies have examined this issue from an environmental perspective, there is a lack of research focusing on crop-specific factors such as crop type. This study aimed to explore the correlation between meteorological and crop factors and mulch contamination. The first step was to estimate the amounts of mulch-derived microplastics (MPs) and phthalic acid esters (PAEs) during the rapid expansion period (1993–2012) of mulch usage in China. Subsequently, the Elastic Net (EN) and Random Forest (RF) models were employed to process a dataset that included meteorological, crop, and estimation data. At the national level, the RF model suggested that coldness in fall was crucial for MPs generation, while vegetables acted as a key factor for PAEs release. On a regional scale, the EN results showed that crops like vegetables, cotton, and peanuts remained significantly involved in PAEs contamination. As for MPs generation, coldness prevailed over all regions. Aridity became more critical for southern regions compared to northern regions due to solar radiation. Lastly, each region possessed specific crop types that could potentially influence its MPs contamination levels and provide guidance for developing sustainable ways to manage mulch contamination.

Effects of plasticizer on removal of antibiotics and antibiotic resistance genes from agricultural soils via soil microbial fuel cells

Soil microbial fuel cells (MFCs), a novel ecosystem technology, have recently been intensively studied for antibiotic-polluted soils. However, actual agricultural soils are always contaminated by mixed pollutants, especially plasticizers from extensively used agricultural plastic films. The aim of this study is to investigate the effect of di-2-ethylhexyl phthalate (DEHP, a representative plasticizer in soil) on the removal of sulfadiazine (SDZ, a frequently detected antibiotic in natural environments), antibiotic resistance genes (ARGs), and the microbial community in soil MFCs. Our results confirmed that soil MFCs maintained a good antibiotic removal ability even under the influence of residual DEHP and achieved a higher removal performance at higher DEHP concentrations due to enhanced power generation. Specifically, a higher DEHP concentration had a favorable effect on antibiotic removal in soil MFCs because the biodegradation efficiency was improved in both the upper (i.e., to 0.268 ± 0.021 mg kg−1 from 4.867 ± 0.221 mg kg−1) and lower layers (i.e., to 0.293 ± 0.047 mg kg−1 from 4.867 ± 0.221 mg kg−1) of polluted soils. Moreover, a high DEHP concentration significantly promoted the abundance of bacteria associated with electricity generation compared with a lower DEHP concentration, resulting in the promotion of extracellular electron transfer, and enhancing SDZ degradation. The increased ARG abundance may have been caused by the enrichment of ARG potential hosts brought about by high DEHP concentrations, likely due to the increased conjugative transfer rates of the RP4 plasmid due to decreased membrane permeability and an increased reactive oxygen species content. The results revealed the ecological risk of residual DEHP in soil that promotes ARG transmission in soil MFCs, although it has the potential to reduce SDZ toxicity through horizontal gene transfer. We also highlight concerns regarding the management of antibiotics and plasticizers in soil. The negative effects of plasticizers on antibiotic removal should be carefully evaluated when using soil MFCs for the in situ remediation of antibiotic-contaminated soil.

Occurrence and characteristics of microplastics in soils from greenhouse and open-field cultivation using plastic mulch film

There is a major knowledge gap concerning the extent of microplastic pollution in agronomic regions of China, which represent a plastic use hotspot. In order to clarify the amendment of agronomic region and plastic film mulching mode to microplastics distribution, the characteristics of microplastics distributed in agricultural soils from three typical regions (Beijing (BJ), Shandong (SD), and Xinjiang (XJ)) with two plastic film mulching modes (greenhouse (G) and conventional field-based film mulching (M)) in China were investigated. Microplastics weight and their response to planting regions were also evaluated in this study. The result showed that the average abundance of microplastics in soils from BJ, SD, and XJ was 1.83 × 104 items kg−1, 4.02 × 104 items kg−1, and 3.39 × 104 items kg−1, and the estimated weight of microplastics per kg of dry soils was 3.12 mg kg−1, 5.63 mg kg−1, and 7.99 mg kg−1, respectively. Microplastics in farmland were mainly of small particle size (50 to 250 μm), with their abundance decreasing with increasing particle size. Among the microplastics detected, polyethylene and polypropylene were the two dominant types present, accounting for 50.0% and 19.7%, respectively. The standard total effect of planting regions on microplastic number and weight was 31.8% and 32.3%, and plastic film mulching modes (G vs. M) could explain 34.4% of the total variation of microplastic compositions with a contribution rate of 65.6% in this study. This research provides key data for an assessment of the environmental risk of microplastics and supports the development of guidelines for the sustainable use of agricultural plastic film. Further, it is necessary to quantify and assess the contribution of other different plastic sources to microplastics in soil. Big data technologies or isotope tracer techniques may be promising approaches.

The Plastic Age: River Pollution in China from Crop Production and Urbanization.

Many rivers are polluted with macro (>5 mm)- and microplastics (<5 mm). We assess plastic pollution in rivers from crop production and urbanization in 395 Chinese sub-basins. We develop and evaluate an integrated model (MARINA-Plastics model, China-1.0) that considers plastics in crop production (plastic films from mulching and greenhouses, diffuse sources), sewage systems (point sources), and mismanaged solid waste (diffuse source). Model results indicated that 716 kton of plastics entered Chinese rivers in 2015. Macroplastics in rivers account for 85% of the total amount of plastics (in mass). Around 71% of this total plastic is from about one-fifth of the basin area. These sub-basins are located in central and eastern China, and they are densely populated with intensive agricultural activities. Agricultural plastic films contribute 20% to plastics in Chinese rivers. Moreover, 65% of plastics are from mismanaged waste in urban and rural areas. Sewage is responsible for the majority of microplastics in rivers. Our study could support the design of plastic pollution control policies and thus contribute to green development in China and elsewhere.

Farmers’ participation into the recovery of waste agricultural plastic film: An application of the Theory of Planned Behavior

This study aims to address the lack of relevant researches in the field of waste recycling using the Theory of Planned Behavior (TPB). A village-scale social survey was conducted to investigate the degree of farmers’ participation in a waste plastic film program, i.e. Old for New in northwest China. The program required farmers to recycle plastic film residues in exchange for new films. Survey results showed that 67.5% of farmers accepted the program, yet only 14.5% of them actually participated. Logistic regression analysis was used to analyze questionnaire data and identify the factors that significantly affected farmers' recycling behavior. Principal component and weight analysis further showed that farmers' participation was mainly influenced by their attitudes (p < 0.01), with a relative weight (RW) of 46.3%. Yet, subjective norms (p < 0.1) and perceived behavior control (p < 0.1) had less effect on the degree of participation, and their RWs were 4.2% and 4.1% only, respectively. Moreover, the RW of plastic film usage characteristics and household characteristics reached up to 13.2% and 6.4%, respectively. Interestingly, environmental awareness (β = 0.083) and compulsory environmental education (β = 0.130) as surface factors strongly affected the farmers' adoption and response, with the RW of 25.7%. As such, the extended TPB model was established to analyze the participation behavior of farmers for stronger explanatory power. This study highlighted a promising strategy based on TPB for waste plastic film recycling and similar environmental management practices.

Mechanical and friction properties of agricultural plastic film during autumn harvest period of cotton in Xinjiang, China.

Agricultural plastic films have caused serious plastic pollution. There are many studies that consider mechanical recycling an appropriate system for the recovery of post-consumption agricultural mulch film. The recovery effect of plastic film depends on the mechanical properties, the level of dirtiness of the post-consumption film, and the recycling process itself. In this study, the mechanical properties of four types of polyethylene plastic films with a thickness of 8, 10, 12, and 10μm, weather-resistant, commonly used in Xinjiang cotton fields, were tested. As well as the friction coefficient between the film and soil, the cotton stalk, boll shell, and leaf with different moisture contents were measured. Then, the self-propelled straw chopping and residual film recycling combined machine collected the four types of mulch films. The results showed that the longitudinal mechanical properties of the plastic film were greater than the transversal ones, with the exception of the nominal tensile strain at break, and the tensile characteristics of the mulching film covered with soil were greater than those without soil. The dynamic or static friction coefficient between the film and the contact material had a linear relationship with the moisture content of the material. During the recycling operation, the better the mechanical properties of the plastic film, the higher the pick-up rate of the mulch film. The maximum longitudinal tensile force of 12-μm plastic film was 3.42 N, and the nominal tensile strain at break was 303.09%. The pick-up rate reached more than 93% when the 12-μm plastic film was recovered in autumn, which effectively reduced the residue of plastic film coverage in the current year. Moreover, the more soil that was present on the much film, the greater the soil content of the recycled film roll, and the stalk content also increased, but the change was small. The research provides a reference for the mechanical and the friction features of agricultural plastic film in Xinjiang, and provides a theoretical basis for the formulation of standards for film thickness and mechanical properties, as well as the design and optimization of a residual film collecting machine in the cotton field.

Analysis and Prediction of the Impact of Socio-Economic and Meteorological Factors on Rapeseed Yield Based on Machine Learning

Rapeseed is one of China’s major oil crops, and accurate yield forecasting is crucial to the growth of the rapeseed industry and the country’s food security. In this study, the data on natural and socio-economic factors from 2001 to 2020 and the yield of rapeseed in China were used as the data basis. The Pearson correlation coefficient was used to analyze the relationship between the influencing factors and the yield of rapeseed, and the prediction effect of four machine learning models (linear regression (LR), decision tree (DTR), random forest (RF), and support vector machine (SVM)) on the yield of rapeseed was compared in China’s main rapeseed-producing area. The results demonstrate that the yield of rapeseed in China showed an increasing trend, but fluctuated greatly. Rural electricity consumption, gross agricultural production, the net amount of agricultural fertilizer application, effective irrigation area, total power of agricultural machinery, and consumption of agricultural plastic film had a positive effect on the increase in rapeseed yield. However, due to the impact of climate change and disasters, the yield of rapeseed has had significant fluctuations. A Pearson correlation analysis showed that socio-economic factors (rural electricity consumption, gross agricultural production, effective irrigation area, total power of agricultural machinery, consumption of agricultural plastic film, etc.) played a dominant role in rapeseed yield changes. The RF model had a good prediction effect on rapeseed yield, and natural factors and socio-economic factors had different effects on spring rapeseed and winter rapeseed. Winter rapeseed yield was mainly affected by socio-economic factors, accounting for as high as 89% of the importance. Among them, the sown area of rapeseed and the effective irrigation area had the greatest impact. The effects of natural factors and socio-economic factors on spring rapeseed yield were similar, accounting for 47% and 53%, respectively, and the mean annual precipitation, sunshine duration, and sown area of rapeseed were the most influential variables.

Release of Additives from Agricultural Plastic Films in Water: Experiment and Modeling.

Globally, more than 6 million metric tons of agricultural plastic films are used to increase crop yields and reduce the use of water and herbicides, resulting in the contamination of soil and water by plastic debris and additives. However, knowledge of the occurrence and release of additives from agricultural films is limited. In this study, suspect screening with high-resolution mass spectrometry, one-dimensional Fickian diffusion models, and linear free energy relationships (LFERs) were used to determine the occurrence and mass transfer of various additives from agricultural plastic films. A total of 89 additives were tentatively identified in 40 films, and 62 of them were further validated and quantified. The aqueous concentrations of 26 released additives reached mg L-1 after a 28 day incubation at 25 °C. Diffusion models and LFERs demonstrated that the film-water partition coefficient and the diffusivity in the polymer, the two critical parameters controlling the mass transfer, could be predicted using Abraham descriptors. The findings of this study highlighted the need for future research on the environmental fate and risk assessment of previously neglected additives in agricultural plastic films and other similar products.

Distribution, Sources, and Behavioral Characteristics of Microplastics in Farmland Soil

Microplastics (MPs) are widely present in farmland soil as an emerging contaminant. This paper serves as a comprehensive and systematic review of research progress on the characteristics of distribution, abundance, sources, shape, polymer composition, size, and migration of MPs in farmland soils around the world. Moreover, research prospects were also proposed. MPs have been detected in farmland soils around the world, mainly coming from agricultural plastic films, organic fertilizers, sludge, surface runoff, agricultural irrigation, atmospheric deposition, and tire wear particles. The morphology of MPs in soil mainly includes debris, fibers, and films. MPs polymer forms mainly include polyethylene, polypropylene, and polystyrene. Farmland land use significantly affects soil MPs abundance. Additionally, the abundance of MPs increase with the reduction in size. MPs in soil can migrate to deep soil through tillage, leaching, bioturbation, and gravity. Research on soil MPs detection methods, database establishment, safety thresholds, migration and transformation laws, potential ecological health risk assessment, and the construction of prevention and control technology systems should be strengthened in the future. The paper can provide a reference for the risk control and governance of farmland soil MPs pollution.

Behavior, Characteristics and Sources of Microplastics in Tea

Microplastics have become a widespread environmental concern because they are found in most tested places, including the air we breathe and the food and beverages we consume. To explore the current status of microplastic pollution and future research trends in tea, we reviewed the distribution, abundance, shape, size and sources of microplastics in tea. Microplastics are plastic particles that are 5 mm in diameter or less. Those found in tea and tea gardens originate from agricultural plastic films, plastic packaging of products and tools used in tea production, organic fertilizers, even atmospheric deposition. The microplastics in tea gardens are typically fragments and fibers, mainly composed of polyethylene, polypropylene and polyethylene terephthalate. The prevention and control of microplastics in tea planting, tea processing and packaging should be strengthened, and reduce the input of products containing microplastics. Future research on microplastic detection methods in tea and determination of safety thresholds should be prioritized to provide a reference for microplastic contamination risk, control, and management in tea.

Design and Test of Stripping and Impurity Removal Device for Spring-Tooth Residual Plastic Film Collector

The residual agricultural plastic film in China is not easily recovered due to the thinness and poor mechanical properties of domestic films, and a large amount of plastic film remaining in farmland soil poses a great threat to soil quality and crop production. A spring-tooth residual plastic film collector (SRPFC) is widely used in domestic residual plastic film (RPF) recycling operations. However, there are two major problems in the current SRPFC: the low recovery rate of the residual film (RRRF) caused by the difficulty of film-stripping and the high impurity rate in the film (IRF). In this paper, a stripping and impurity removal device (SIRD) is designed to address the existing problems of SRPFC, which is mainly composed of film-stripping tooth plates (FTP), two wind-collecting hoods, and two centrifugal fans. The motion and force analysis of the RPF in the film-stripping process was carried out, and the arc FTP was determined to be used for film-stripping. The size parameters of the FTP were obtained by establishing the coordinate system to solve the differential equation. By comparing and analyzing the force of RPF in the airflow field of the test bench for suspension speed and the airflow field of the wind-collecting hood, the RPF equivalent particle was established. The discrete phase model (DPM) in Fluent software was used to simulate the movement of the RPF equivalent particle, and the calculated air volume range of the centrifugal fan was 5501.88~6829.92 m3/h. The effects of forward speed, rotating speed of film conveying chain harrow (FCCH), and rotating speed of the centrifugal fan on RRRF and IRF were studied by orthogonal rotary combination experiment. The test results showed that the best combination of machine operation parameters was when the forward speed was 5 km/h, the rotating speed of the FCCH was 235 r/min, and the rotating speed of the centrifugal fan was 1978 r/min. Under these conditions, the RRRF was 92.53%, and the IRF was 9.31%. Field experiments were carried out with the rounded parameters, and the average RRRF was 92.07%, and the average IRF was 9.56% under the parameter combination, indicating that the optimization scheme of the device was feasible.

Hydrophobic self-cleaning micro-nano composite polyethylene-based agricultural plastic film with light conversion and abrasion resistance

Agricultural plastic film (APF) is extensively used in modern agriculture. However, to the best of our knowledge, the self-cleaning property and light transmittance of APF are still the main factors affecting crop yield at present. To solve these problems, for the first time, we developed polyethylene-based dust-proof composite APF with multi-scale micro-nano structure and light conversion performance. By combining the carbon dots (CDs) and hydrophobic silica nanoparticles (FSi-SiO2) with organically modified montmorillonite (OMMT), composite materials with multi-scale micro-nano structure and low surface energy (SFE) were constructed (FSi-SiO2/CDs@OMMT). After blending with linear low-density polyethylene (LLDPE, PE), a self-cleaning dust-proof APF with “lotus-effect” was synthesized (PE/FSi-SiO2/CDs@OMMT). The PE/FSi-SiO2/CDs@OMMT exhibited excellent hydrophobic property, which had a water contact angle (WCA) of 108.9°. The results of the mechanical properties tests showed that the horizontal and portrait tensile strength of PE/FSi-SiO2/CDs@OMMT improved from 25.08 and 27.41 MPa to 33.14 and 42.21 MPa and that the horizontal and portrait elongation at break improved from 273.53 % and 380.23–369.43 % and 480.73 %, respectively. In addition, the anti-fouling and dust-proof performance were studied, and the results showed that the anti-fouling rate and dust removal efficiency of PE/FSi-SiO2/CDs@OMMT were reached to 99.84 % and 99.58 %, respectively. Additionally, PE/FSi-SiO2/CDs@OMMT also possessed excellent thermal stability, anti-algae and anti-bacterial adhesion properties, and light conversion performance. This work could provide a facile approach and strategy to fabricate functional APF for agricultural application.

Distribution and weathering characteristics of microplastics in paddy soils following long-term mulching: A field study in Southwest China

Agricultural plastic-film residues have been considered as one of the important sources of microplastics in the agroecosystem. However, limited researches were conducted on the accumulation of microplastics in long-term film-mulched paddy soil. This study aims to investigate the distribution and the weathering characteristics of filmy microplastics in a mulched paddy field (non-mulch, four years of mulched, and ten years of continuous mulched soil were investigated) in Southwest China. More than 50 % of the microplastics in the mulched soil were 1–3 mm, whereas the largest percentage of the microplastics in the non-mulched soil was <1 mm (55.3 %). Microplastic compositions in this field mainly consist of polyester (PES) and polyethylene (PE) (82.1 %). The abundance of microplastics increases with the film mulching time, which were 76.2 ± 18.4, 118.6 ± 44.8, and 159.6 ± 23.5 items kg−1 in soil with non-mulching, four years of mulching, and ten years of continuous mulching, respectively. The filmy microplastics accumulated annually in the plough layer is estimated at 18.1 million items ha−1. Weathering characteristics of filmy microplastics extracted from paddy soil were characterized using FTIR, SEM-EDS, AFM, and contact angle meter. The vinyl, carbonyl, and hydroxyl indices calculated from FTIR results showed that the degradation degree of microplastics incereased as mulching time rose; compared with commercial PE films, the oxygen-containing functional groups of soil-extracted PE films were increased. This study revealed the status of microplastic pollution in paddy soil with long-term mulching. It provided primary data and a scientific basis for further study on environmental behavior and ecological impacts of microplastics in agricultural soils.