Metal Adsorption Capacity Research Articles

Development of a composite MoS2/PEI nanofiltration membrane for radionuclides efficient removal from aquatic environments

The simultaneously efficient removal of radionuclides and heavy metals is an important and challenging topic for aquatic environmental protection. In this work, molybdenum disulfide (MoS2) with heavy metal ion adsorption capacity and positively charged polyethyleneimine (PEI) were used to fabricate a novel layer-by-layer (LbL) self-assembly composite membrane by a simple alternating immersion method. The unique structure with positive charge ensures high removal for toxic metals (RCs(I) = 99.83 %, RSr(II) = 100 %, RHg(II) = 99.2 %, RPb(II) = 98.13 %, RAs(III) = 98.5 %). The inherent low resistance channels in MoS2 provided the optimized composite membrane an elevated water flux. Long-term experiments and membrane regeneration also demonstrated that the membrane possesses exceptional stability and reusability in removing low levels of radionuclides Cs(I) and Sr(II) from water. This study confirms the feasibility of the MoS2-PEI composite membrane for the treatment of contaminated waters containing radionuclides and heavy metals.

Enhanced heavy metal adsorption capacity of surface-functionalized Philippine natural zeolite in simulated wastewater

The adsorption efficiency of surface-functionalized Philippine natural zeolite (PNZ) for heavy metal uptake from single and mixed metal ion-simulated wastewater solution is reported in this work. Atomic adsorption spectroscopy (AAS) findings revealed that NaCl-modified PNZ (MPNZ) exhibited the highest zinc ion adsorption of 99.96 % while PNZ yielded an adsorption of 95.61 %. The adsorption isotherms of raw PNZ and MPNZ both show similar shapes that reflect Type IV adsorption-desorption isotherms with Type H2 hysteresis loop which can be observed for micro-mesoporous materials (pore containing 2–50 nm). An increase in PNZ pore size from 10.11 nm to 13.36 nm for NaCl-PNZ and 15.59 for NaOH-PNZ is observed after alkaline treatment. EDS confirmed the decrease in Si/Al ratio from 4.02 to 3.76, indicative of possible higher negative charge in the PNZ framework which is favorable for an enhanced Coulombic or electrostatic interaction with the cationic heavy metals being detected in this study. MPNZ demonstrated an adsorption capacity of 99.96 % for copper in mixed-ion solution while 88.49 % and 86.67 % were obtained for zinc and nickel, respectively. These values are higher compared to PNZ having only 32.21 % uptake for zinc and 38.00 % for nickel. A hierarchy of the average metal adsorption capacity showed the order: copper > nickel > zinc. Rapid adsorption at the first hour of the adsorption reaction was attained in all solutions while samples with pH 9 exhibited the highest Ni2+ and Zn2+ percent removal. Moreover, the increase in initial solution concentration led to lower adsorption efficiency and the maximum uptake was attained at 100 ppm. The equilibrium data of adsorption and mechanism were suitably described by Langmuir isotherm model. With these, surface functionalization of PNZ has further enhanced its cationic adsorption capacity on heavy metals in both single and mixed-ion solution having promising potential for wastewater remediation.

Antibacterial, antioxidant, Cr(VI) adsorption and dye adsorption effects of biochar-based silver nanoparticles‑sodium alginate-tannic acid composite gel beads

Ultrasonic extraction of Osmanthus fragrans was used for reducing Ag+ to prepare AgNPs, which were further loaded on barley distiller's grains shell biochar. By supplementary of sodium alginate and tannic acid, composite gel beads were prepared. The physical properties of biochar-based AgNPs‑sodium alginate-tannic acid composite gel beads (C-Ag/SA/TA) were characterized. SEM, FTIR, and XRD showed that biochar-based AgNPs were compatible with sodium alginate-tannic acid. CAg greatly improved the dissolution, swelling, and expansion of gel beads. Through the analysis by the agar diffusion method, C-Ag/SA/TA gel beads had high antibacterial activity (inhibition zone: 22 mm against Escherichia coli and 20 mm against Staphylococcus aureus). It was observed that C-Ag/SA/TA composite gel beads had high antioxidant capacity and the free radical scavenging rate reached 89.0 %. The dye adsorption performance of gel beads was studied by establishing a kinetic model. The maximum adsorption capacities of C-Ag/SA/TA gel beads for methylene blue and Congo red were 166.57 and 318.06 mg/g, respectively. The removal rate of Cr(VI) reached 96.4 %. These results indicated that the prepared composite gel beads had a high adsorption capacity for dyes and metal ions. Overall, C-Ag/SA/TA composite gel beads were biocompatible and had potential applications in environmental pollution treatment.

Unlocking the potential of phenolated kraft lignin as a versatile feed additive

Lignin, a renewable natural antioxidant and bacteriostat, holds promise as a versatile, cost-effective feed additive. However, traditional industrial lignin faces limitations, including low reactivity, poor uniformity, and unstable properties, necessitating chemical modification. Complex modification methods pose economic and toxicity challenges, so this study adopted a relatively simple alkali-catalyzed phenolization approach, using phenol, catechol, and pyrogallol to modify kraft lignin, and characterized the resulting products using various techniques. Subsequently, their antioxidant, antibacterial, adsorption properties for heavy metal ions and mycotoxins, growth-promoting properties, and antiviral abilities were assessed. The phenolation process led to lignin depolymerization and a notable increase in phenolic hydroxyl content, particularly in pyrogallol-phenolated lignin (Py-L), rising from 3.08 to 4.68 mmol/g. These modified lignins exhibited enhanced antioxidant activity, with over 99 % inhibition against E. coli and S. aureus, and remarkable adsorption capacities for heavy metal ions and mycotoxins. Importantly, Py-L improved the growth performance of mice and reduced influenza mortality. Furthermore, density functional theory calculations elucidated the mechanism behind the enhanced antioxidant properties. This study presents a promising avenue for developing versatile feed additives to address challenges related to animal feed antioxidant supplementation, bacterial control, and growth promotion.

Application and mechanism of carbonate material in the treatment of heavy metal pollution: a review.

Among the many heavy metal pollution treatment agents, carbonate materials show strong flexibility and versatility by virtue of their high adsorption capacity for heavy metals and the characteristics of multiple and simple modification methods. It shows good potential for development. This review summarizes the application of carbonate materials in the treatment of heavy metal pollution according to the research of other scholars. It mainly relates to the application of surface-modified, activated, and nano-sized carbonate materials in the treatment of heavy metal pollution in water. Natural carbonate minerals and composite carbonate minerals solidify and stabilize heavy metals in soil. Solidification of heavy metals in hazardous waste solids is by MICP. There are four aspects of calcium carbonate oligomers curing heavy metals in fly ash from waste incineration. The mechanism of treating heavy metals by carbonate in different media was discussed. However, in the complex environment where multiple types of pollutants coexist, questions on how to maintain the efficient processing capacity of carbonate materials and how to use MICP to integrate heavy metal fixation and seepage prevention in solid waste base under complex and changeable natural environment deserve our further consideration. In addition, the use of carbonate materials for the purification of trace radioactive wastewater and the safe treatment of trace radioactive solid waste are also worthy of further exploration.

Recycling lithium-ion battery graphite: Synthesis of adsorbent materials for highly efficient removal of dye and metal ions from wastewater

The fate of residual graphite derived from hydrometallurgical treatment of spent Lithium-ion batteries remains uncertain. This study dwells on the aim of identifying the potentialities of recycling residual graphite for wastewater treatment. Graphite was recovered hydrometallurgically, and new adsorption materials: graphite oxide (GO) and graphene oxide (GrO) were synthesized from the residual graphite using the chemical oxidization method. Synthesized materials showed higher interlayer spacings (GO = 0.81 nm, GrO = 0.78 nm) than the commercially available similar materials. Adsorption studies revealed higher adsorption capacities for both dye (>550 mg/g in all cases) and metal ions (highest ∼93 mg/g for Ni2+ and lowest ∼68 mg/g for Zn2+). GrO showed superior results than GO due to its high surface area and porosity despite GO having more functional groups. Moreover, produced materials showed about 97 % removal of dye and about 94 % removal of contaminated metals which are higher performance than existing commercial or similar materials. These findings highlight the promising recycling capabilities of waste graphite and suggest its potential as a substitute for natural graphite.

Cellulose-Based Hydrogels for Wastewater Treatment: A Focus on Metal Ions Removal.

The rapid worldwide industrial growth in recent years has made water contamination by heavy metals a problem that requires an immediate solution. Several strategies have been proposed for the decontamination of wastewater in terms of heavy metal ions. Among these, methods utilizing adsorbent materials are preferred due to their cost-effectiveness, simplicity, effectiveness, and scalability for treating large volumes of contaminated water. In this context, heavy metal removal by hydrogels based on naturally occurring polymers is an attractive approach for industrial wastewater remediation as they offer significant advantages, such as an optimal safety profile, good biodegradability, and simple and low-cost procedures for their preparation. Hydrogels have the ability to absorb significant volumes of water, allowing for the effective removal of the dissolved pollutants. Furthermore, they can undergo surface chemical modifications which can further improve their ability to retain different environmental pollutants. This review aims to summarize recent advances in the application of hydrogels in the treatment of heavy metal-contaminated wastewater, particularly focusing on hydrogels based on cellulose and cellulose derivatives. The reported studies highlight how the adsorption properties of these materials can be widely modified, with a wide range of adsorption capacity for different heavy metal ions varying between 2.3 and 2240 mg/g. The possibility of developing new hydrogels with improved sorption performances is also discussed in the review, with the aim of improving their effective application in real scenarios, indicating future directions in the field.

Mesoporous Mg–Al–Ti composite oxide incorporated mixed matrix ultrafiltration membrane with superior multi-heavy metal removal capacity, anti-fouling & anti-microbial property

Mesoporous Mg–Al–Ti ternary composite oxide nano-adsorbents have demonstrated an exceptional performance to remove multiple heavy metals (As, Pb, Cd, Cr). Incorporation of these nanoparticles (NPs) in polysulfone membrane created a multifunctional mixed matrix membrane (MMM) with heavy metal adsorption capacity (both cationic and anionic species), enhanced hydrophilicity, anti-fouling property, and anti-microbial activity. The best heavy metal removal performance was shown by the membrane incorporated with 0.8 wt% NPs. Hydrophilicity improvement was studied through the decrease in water contact angle from 71° to 57° and surface probing using atomic force microscopy (AFM). With a maximum As(III) adsorption capacity of 256.6 mg/g, the membrane had a breakthrough volume of 25L and could provide safe drinking water for 19 h from a real Arsenic (As) contaminated groundwater sample with a flux of 48 l/m2-h. Beyond that, >90 % removal of Cd, Pb & Cr was also observed with maximum adsorption capacity of 652.9 mg/g, 332.5 mg/g, and 89.4 mg/g respectively. 92.5 % flux recovery after filtering a 1000 ppm bovine serum albumin showed the anti-fouling property. Successful inhibition of both gram-positive and gram-negative bacterial growth, and >99.99 % removal of colony forming units (CFU/ml) in the filtration process confirmed the anti-microbial resistance. With its multifunctionality, these membranes hold great potential for practical water treatment applications.

Optimising Low Temperature Pyrolysis of Mesoporous Alginate-Derived Starbon® for Selective Heavy Metal Adsorption.

In response to the ever increasing need to develop more efficient and sustainable methods for removing heavy metal contaminants from aqueous systems, the following article reports on the design of highly mesoporous alginate-derived materials (Starbon®) and their application to the adsorption of heavy metals. Using the Starbon® process to expand, dry and pyrolyse an inherently porous polysaccharide precursor, it was possible to produce mesoporous materials (BJH mesopore volumes 0.81-0.94 cm3 g-1) with large surface areas (157-297 m2 g-1) across a range of low pyrolysis temperatures (200-300 °C). The mechanisms of thermal decomposition were explored in terms of chemical and structural changes using N2-sorption porosimetry, thermogravimetric analysis, titration, FT-IR spectroscopy and 13C NMR spectroscopy. It was found that, as a result of intermolecular dehydration and crosslinking, sufficient chemical stability is obtained by the intermediate temperature of 250 °C, with limited improvement seen at higher temperatures. In addition, the materials retained large metal adsorption capacities (0.70-1.72 mmol g-1) as well as strong selectivity for Cu2+ ions (over Co2+ and Ni2+), as compared to commercial petrochemical-derived cation exchange resin Amberlite™ Mac 3H. Thus, highlighting the potential of Starbon® materials as a sustainable answer to the widespread problem of heavy metal-contaminated wastewaters.

Adsorption mechanism of Cs+ and Pb2+ on the N-A-S-H surface under the different Si/Al ratio and temperature

The application of low-calcium alkali-activated geopolymers has significantly enhanced the removal of Pb2+ and Cs+ from the contaminated soils and water. However, the adsorption mechanisms of Pb2+ and Cs+ influenced by the temperature and Si/Al at the molecular scale remain unclear, which were the two critical factors influencing the adsorption capacity. This study employed molecular dynamics simulation to elucidate the effects of temperature and Si/Al ratio on the adsorption mechanism and behavior of Pb2+ and Cs+ on the N-A-S-H surface. Research findings demonstrate that the adsorption of Pb2+ and Cs+ on the N-A-S-H surface is attributed to chemical adsorption. Increasing temperature can regulate the removal ratio of heavy metal ions by enhancing the quantity of cation exchange (correlation coefficient of 0.88). Temperature also influences the removal ratio by changing in adsorption energy, potential of mean force, and controlling the maximum adsorption capacity, hydration, and diffusion ability of the heavy metals (correlation coefficient of 0.67, 0.55, 0.6, and 0.57). While the Si/Al ratio influences the adsorption of heavy metals by enhancing the negative charge density of N-A-S-H gel and strengthening the interaction between heavy metals and oxygen atoms on the N-A-S-H surface (correlation coefficient of 0.96 and 0.52). Additionally, temperature exhibits a more pronounced effect on enhancing in the removal ratio of heavy metals. The heavy metal removal was maximally increased by 435 % (for Cs+) and 439 % (for Pb2+) via elevated temperature, while it was increased by 63 % (for Cs+) and 98 % (for Pb2+) via decreased Si/Al ratio. This study can not only provide a new perspective on the removal of heavy metals by N-A-S-H gel, but also can contribute to the achievement of green and sustainable development goals.

Ultrafast and highly efficient Cd(II) and Pb(II) removal by magnetic adsorbents derived from gypsum and corncob: Performances and mechanisms

The utilization of gypsum and biomass in environmental remediation has become a novel approach to promote waste recycling. Generally, raw waste materials exhibit limited adsorption capacity for heavy metal ions (HMIs) and often result in poor solid–liquid separation. In this study, through co-pyrolysis with corncob waste, titanium gypsum (TiG) was transformed into magnetic adsorbents (GCx, where x denotes the proportion of corncob in the gypsum–corncob mixture) for the removal of Cd(II) and Pb(II). GC10, the optimal adsorbent, which was composed primarily of anhydrite, calcium sulfide, and magnetic Fe3O4, exhibited significantly faster adsorption kinetics (rate constant k1 was 218 times and 9 times of raw TiG for Cd(II) and Pb(II)) and higher adsorption capacity (Qe exceeded 200 mg/g for Cd(II) and 400 mg/g for Pb(II)) than raw TiG and previous adsorbents. Cd(II) removal was more profoundly inhibited in a Cd(II) + Pb(II) binary system, suggesting that GC10 showed better selectivity for Pb(II). Moreover, GC10 could be easily separated from purified water for further recovery, due to its high saturation magnetization value (6.3 emu/g). The superior removal capabilities of GC10 were due to adsorption and surface precipitation of metal sulfides and metal sulfates on the adsorbent surface. Overall, these waste-derived magnetic adsorbents provide a novel and sustainable approach to waste recycling and the deep purification of multiple HMIs.

Machine learning-based prediction and experimental validation of heavy metal adsorption capacity of bentonite

As a natural adsorbent material, bentonite is widely used in the field of heavy metal adsorption. The heavy metal adsorption capacity of bentonite varies significantly in studies due to the differences in the properties of bentonite, solution, and heavy metal. To achieve accurate predictions of bentonite's heavy metal adsorption capacity, this study employed six machine learning (ML) regression algorithms to investigate the adsorption characteristics of bentonite. Finally, an eXtreme Gradient Boosting Regression (XGB) model with outstanding predictive performance was constructed. Explanation analysis of the XGB model further reveal the importance and influence manner of each input feature in predicting the heavy metal adsorption capacity of bentonite. The feature categories influencing heavy metal adsorption capacity were ranked in order of importance as adsorption conditions > bentonite properties > heavy metal properties. Furthermore, a web-based graphical user interface (GUI) software was developed, facilitating researchers and engineers to conveniently use the XGB model for predicting the heavy metal adsorption capacity of bentonite. This study provides new insights into the adsorption behaviors of bentonite for heavy metals, offering guidance and support for enhancing its application efficiency and addressing heavy metal pollution remediation.

A spherical adsorbent produced from a bagasse biochar chitosan assembly for selective adsorption of platinum-group metals from wastewater

This study addresses the challenge of platinum-group metal scarcity by exploring the adsorption of these metals from industrial wastewater. An inexpensive adsorbent with selective platinum-group metal adsorption capacity, named chitosan/citric acid@diatomaceous earth-sugarcane bagasse (CTS/CA@DE-SBS), was newly synthesized. The material features a double coating of chitosan and diatomite on bagasse biochar, and it exhibits an excellent adsorption performance for platinum-group metals due to the synergistic effects of the biochar and chitosan-diatomaceous earth intercross-linked coatings. CTS/CA@DE-SBS achieved an 81 % adsorption efficiency and a static saturated adsorption capacity of 217 mg/g for Pt (IV) in water. Notably, the material exhibited selective adsorption properties for platinum-group metals dissolved in diverse aqueous solutions. The potential for the secondary recovery of platinum-group metals in complex aqueous bodies further underscores the significance of this adsorbent. In conclusion, this research introduces a promising solution for platinum-group metal shortages, offering a cost-effective and selective adsorbent with potential applications in the secondary recovery of these metals from industrial wastewater.

Machine Learning Application to Optimize Spent Mushroom Compost (SMC) Biochar as Filter Media for Heavy Metal Adsorption in Abandoned Mine Water

AbstractThe surging global population strains resources, escalating pollution, and exacerbating water scarcity. Sustainable water management necessitates alternative sources such as abandoned mine water. However, these sources often contain hazardous heavy metals, like lead, copper, iron, and manganese, posing grave health and environmental risks. Conventional methods struggle to effectively treat these heavy metals in abandoned mining ponds, urging the search for cost‐efficient and sustainable solutions. Biochar, particularly from spent mushroom compost (SMC), emerges as a potent adsorbent due to its high surface area and binding groups. Yet, the variability in its efficiency remains a challenge. Conventional empirical models fail to capture the dynamic nature of adsorption processes accurately. Adopting machine learning, specifically an adaptive neuro‐fuzzy inference system (ANFIS), shows potential in predicting adsorption efficiency. This study aims to employ ANFIS to forecast SMC biochar's performance in a lab‐scale metal retention pond, providing design charts for diverse initial metal concentrations and pH levels. Validation through real cases aims to enhance accuracy and establish a framework for future heavy metal adsorption capacities. This research offers a sustainable approach to removing heavy metals from abandoned mining ponds whereas the computational modeling in optimizing SMC biochar introduces a novel approach for practical applications.

Activated nanosulfur for broad-spectrum heavy metals capture

Current problems of existing heavy metal-removing technologies, especially for nanomaterials-based ones, are typically single metal ion-specific, high-cost and collected difficult. Herein, facile modification of commercial sulfur creates a versatile adsorbent platform to address challenges. The versatile adsorbent can be easily prepared through solvothermal treatment of a saturated commercial sulfur solution, followed by water precipitation on a commercial foam that eliminates the need for separation. Interestingly, the solvothermal treatment endows the resulting nanosulfur with sulfate acid groups (hard Lewis base), sulfur anions (soft base), and sulfite groups (borderline base), promising the coordination of all types of heavy metal ions (Lewis acids). As such, this versatile adsorbent with well-distributed adsorption sites exhibits highly effective heavy metal adsorption capacity towards diverse heavy metal ions for both single-component and multi-component adsorption, including soft, hard, borderline Lewis metal ions, with ultra-high adsorption ability (e.g., 903.79 mg g−1 for Cu2+). These findings highlighted the potential of this low-cost sulfur-based adsorbent to address the arising challenges in ensuring clean water.

The application of machine learning methods for prediction of heavy metal by activated carbons, biochars, and carbon nanotubes

Carbonaceous materials are commonly used as adsorbents for heavy metals. The determination of the adsorption capacity needs time and energy, and the key factors affecting the adsorption capacity have not been determined. Therefore, a new and efficient method is needed to predict the adsorption capacity and explore the decisive factors in the adsorption process. In this study, three tree-based machine learning models (i.e., random forest, gradient boosting decision tree, and extreme gradient boosting) were developed to predict the adsorption capacity of eight heavy metals (i.e., As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn) on activated carbons, biochars, and carbon nanotubes using 3674 data points extracted from 151 journal articles. After a comprehensive comparison, the gradient boosting decision tree had the best performance for a combined model based on all data (R2 = 0.9707, RMSE = 0.1420). Moreover, independent models were developed for three datasets classified by the adsorbent and eight datasets classified by the heavy metals. In addition, a graphical user interface was built to predict the adsorption capacity of heavy metals. This study provides a novel strategy and convenient tool for the removal of heavy metals and can help to improve the removal efficiency of heavy metals to build a healthier world.

Efficiency of green synthesised carbon nanotubes from Moringa oleifera leaf extract as potential toxic metals adsorbent in polluted water

Abstract Among the many drawbacks of the current wastewater treatment systems are their high energy consumption and creation of harmful sludge. Carbon nanotubes (CNTs) are advantageous for the treatment of water due to their strong adsorption capacity and selectivity towards various pollutants. Thus, creating methods for treating water by producing CNTs from Moringa oleifera leaf extract can greatly help with the clean water problem. The synthesised material’s Ultra Visible (260–385 nm), FTIR (764–3295 cm−1) and Scanning Electron Microscope (SEM) characterizations have demonstrated their CNTs characteristics. The repeatability testing yielded the %RSD values for Ca = 0.4, Cu = 0.24, Mg = 0.9, Pb = 1.06 and Zn = 0.36 which suggest that the AES approach demonstrated a high degree of precision. The findings show that the quantity of recovered metals increases with retention period. Mg > Cu > Zn > Ca > Pb was the order of the metal adsorption capacity throughout retention durations of 3, 6, 24, and 48 h. As the initial concentrations of the components under research were doubled and tripled, so were the removal capacities of CNTs increased which may be as a result of an increase in metal ions in the solution. The outcomes show how well the synthetic CNTs can remove heavy metals from wastewater.

Metabolomics-based analysis of the interaction effects and stress response mechanisms in the co-culture system of fungi and microalgae under cadmium stress

Research on the co-culture of fungi and microalgae to harvest microalgae and enhance the adsorption capacity for heavy metals to reduce contamination is well demonstrated, but the study of the correlation mechanism among critical metabolites, system stability, and stress response in the system under cadmium stress based on metabolomics analyses has not been reported in detail. In this study, the co-culture system of Aspergillus allahabadii and Synechocystis sp. PCC6803 was taken as the object of investigation, and isotope labelling (13C–Na2CO3 and 15N-(NH4)2SO4) and nanoscale secondary ion mass spectrometry were used to confirm the existence of carbon and nitrogen nutrient exchange. The adsorption behavior of the system after Cd treatment was investigated by Fourier Transform Infrared Spectroscopy, X-ray Photoelectron Spectroscopy, and Scanning Electron Microscope/Transmission Electron Microscope. The content of extracellular polysaccharides in the system was increased from 40.8 mg/g to 80.12 mg/g, and the content of extracellular proteins was increased from 22.3 mg/g to 55.68 mg/g after 96 h of Cd treatment. Metabolomics results revealed 235 differential metabolites co-expressed after Cd treatment, with 95, 15, and 77 unique differential metabolites. In particular, the synthesis of extracellular polymeric substances was a factor affecting the stability of the symbiotic system, the up-regulation of the expression of the transporter system was one of the reasons for the improvement of the system's tolerance and resistance to heavy metals; and the nutrient metabolism between the fungus and the microalgae was the main defense mechanism to reduce the extent of the impairment of the system's carbon sequestration capacity by Cd. This provides a theoretical basis for the green and economically friendly application of the symbiotic system in microalgae harvesting, efficient carbon dioxide fixation and reduction of heavy metal pollution.

Study on the solidification performance and mechanism of heavy metals by sludge/biomass ash ceramsites, biochar and biomass ash.

Industrial by-products are stored in large quantities in the open, leading to wasted resources and environmental pollution, and the natural environment is similarly faced with phosphate depletion and serious water and soil pollution. This study uses these by-products to produce a new sludge/biomass ash ceramsite that will be used to adsorb nitrogen and phosphorus from wastewater, and solidify heavy metals in the soil while releasing Olsen P. The sludge/biomass ash ceramsites are made using sewage sludge and biomass ash in a certain ratio calcined at high temperatures and modified for the adsorption of nitrogen and phosphorus from wastewater. Sludge/biomass ash ceramsites before and after phosphorus adsorption, biochar and biomass ash were compared to analyze their heavy metal adsorption capacity and potential as phosphate fertilizer. After phosphorus adsorption, the sludge/biomass ash ceramsites released effective phosphorus steadily and rapidly in the soil, with a greater initial release than biochar and biomass ash, and the ceramsites were in a granular form that could be easily recycled. Biochar and biomass residue, due to their surface functional groups, are better at solidifying heavy metals than sludge/biomass ash ceramsites. Biochar, biomass ash and sludge/biomass ash ceramsites significantly reduced the concentrations of Cd, Cu, Pb and Zn in the soil. Correlation analysis demonstrated that there was a synergistic relationship between the increase in soil Olsen P content and the change in pH, with the increase in soil Olsen P content and the increase in pH contributing to heavy metal solidification.

Efficient and Selective Removal of Heavy Metals and Dyes from Aqueous Solutions Using Guipi Residue-Based Hydrogel.

The presence of organic dyes and heavy metal ions in water sources poses a significant threat to human health and the ecosystem. In this study, hydrogel adsorbents for water pollution remediation were synthesized using Guipi residue (GP), a cellulose material from Chinese herbal medicine, and chitosan (CTS) through radical polymerization with acrylamide (AM) and acrylic acid (AA). The characteristics of the hydrogels were analyzed from a physicochemical perspective, and their ability to adsorb was tested using model pollutants such as Pb2+, Cd2+, Rhodamine B (RhB), and methyl orange (MO). The outcomes revealed that GP/CTS/AA-co-AM, which has improved mechanical attributes, effectively eliminated these pollutants. At a pH of 4.0, a contact duration of 120 min, and an initial concentration of 600 mg/L for Pb2+ and 500 mg/L for Cd2+, the highest adsorption capabilities were 314.6 mg/g for Pb2+ and 289.1 mg/g for Cd2+. Regarding the dyes, the GP/CTS/AA-co-AM hydrogel displayed adsorption capacities of 106.4 mg/g for RhB and 94.8 mg/g for MO, maintaining a stable adsorption capacity at different pHs. Compared with other competitive pollutants, GP/CTS/AA-co-AM demonstrated a higher absorption capability, mainly targeted toward Pb2+. The adsorption processes for the pollutants conformed to pseudo-second-order kinetics models and adhered to the Langmuir models. Even after undergoing five consecutive adsorption and desorption cycles, the adsorption capacities for heavy metals and dyes remained above 70% and 80%. In summary, this study effectively suggested the potential of the innovative GP/CTS/AA-co-AM hydrogel as a practical and feasible approach for eliminating heavy metals and dyes from water solutions.