Addition Of Oil Research Articles

Development and Characterization of Novel Green Cutting Fluids with Nano-additives

In this current investigation, novel cutting fluids developed through a unique combination of food grade emulsifiers, plant based additives (EA) and nano particles (NP) as cutting fluid additives in corn oil (CO) based vegetable oil. Five dissimilar corn-based green cutting fluids (CBGC1, CBGC2, CBGC3, CBGC4, CBGC5) were prepared by varying the weight percentages (wt.%) of EAs (5, 10, 15, 20, 25) with CO, and their thermo-physical properties were meticulously analyzed. Among these formulations, CBGC2 demonstrated superior lubrication performance, making it the most promising oil for further investigation. Subsequently, the effect of different NP was investigated by adding alumina (Al2O3), graphene (Gr) and multi walled carbon nanotubes (MWCNT) NPs in the CBGC2 solution in the ratio of 0.4, 0.8 and 1.2 in weight percent (wt.%) and the experimental results reveal substantial enhancements in thermophysical properties. Among various samples, the nanofluid containing 0.8 wt.% concentration of Al2O3 nanoparticles in CBGC2 exhibited the highest viscosity. Additionally, the thermal conductivity of the nanofluid enhanced by 24.82% when 1.2 wt.% of Gr nanoparticles added oil compared to CBGC2. Furthermore, in tribological tests, CBGC2 with 0.4% Al2O3 exhibited the lowest frictional force among the prepared cutting fluids. The contact angle reduced to a maximum extent by 11.14% for cutting fluids containing 1.2% alumina nanoparticles. These findings suggest that these innovative green cutting fluid formulations with nano-additives hold great potential for improving machining processes in various industrial applications towards sustainability.

Alkali activated steel slag – oil composites: Towards resource efficiency and CO2 neutrality

This study describes advances in high-performance construction material development using a minimum of primary resources while enabling simultaneous CO2 sequestration capacities. Two so far unutilized Austrian steel slags were combined with metakaolin and vegetable oil to produce alkali-activated materials exhibiting high compressive and flexural strength of up to 94 MPa and 13 MPa, respectively. This approach enabled a reduction in primary mineral resources of up to 82 wt%, with an average reduction in global warming potential (GWP) of 52 % compared to a traditional high-performance Portland cement material. Oil addition led to the formation of mainly water unsolvable metal soap phases precipitating within the pore spaces without significantly altering the phase assemblage and chemistry of the binder matrix, but further reducing the GWP by 74 %. The (heavy metal) leaching behavior coincides with that of traditional concrete materials and was even further reduced by the addition of oil.

Lemongrass essential oil in silage and as a feed additive has limited effect on animals feed intake and rumen fermentation

ABSTRACT This study aimed to evaluate the effects of lemongrass essential oil (LEO) addition during the ensiling and subsequent sheep feed intake, particle selection, in vitro rumen fermentation, total-tract apparent digestibility and nitrogen balance. Eight Dorper lambs 19.4±2.40 (mean±SD) kg of body weight were used in a trial using a 4 × 4 Latin Square design to evaluate: I. LEO addition during the whole-plant sorghum ensiling: 0 (EN−) and 4 (EN+) mL per kg of sorghum dry matter (DM); and II. LEO supply during the animals feeding: 0 (F−) and 1.6 (F+) mL per kg of diet DM. Treatments showed no effect on feed intake and particle size selection. Ensiling with LEO increased ammonia-N when LEO was not added during incubation. LEO addition during incubation decreased neutral detergent fibre (NDF) degradation when LEO was not added during the ensiling. In addition, LEO addition increased fermentation gas production and decreased digestibility. LEO addition in sheep feeding tended to decrease crude protein digestibility. Treatments did not affect nitrogen balance and the average daily gain. Thus, LEO supply during ensiling and sheep feeding does not affect feed intake, particle selection and nitrogen balance.

Comparison of the effect of vegetable oil and oleogels with different unsaturation on gel properties of Nemipterus virgatus surimi

The effect of oleogels prepared using γ-oryzanol, β-sitosterol and vegetable oils with different unsaturation on the gel properties of surimi was compared. The findings from SEM and optical microscopy demonstrated that direct addition of vegetable oils caused loose surimi gel three-dimensional network structure, which negatively impacted the water holding capacity (WHC) and texture properties. However, oleogels increased the hydrophobic interaction and disulfide bond content, facilitated the transition from α-helix to β-sheet, improving the WHC and gel strength of surimi. Among them, the surimi containing oleogels prepared by linseed oil with the highest polyunsaturated fatty acid (PUFA) content had the highest gel strength and WHC, which were 3936.067 g·mm and 66.77 %, respectively. The results of microstructure showed that linseed oil based oleogels were able to fill the gaps of gel network more uniformly with smaller holes. Therefore, oleogels enriched with PUFA were more effective in enhancing the gel properties of surimi.

RESEARCH ON THE INFLUENCE OF ONION OIL AS ADDITIVE ON THE OPERATION OF DIESEL ENGINE POWERED BY BIODIESEL

The conventional fuel used to produce electrical energy and the burning of the conventional fuel causes global warming. Also, there is a depletion of these fuel and hence there is a need of alternative fuels. The biodiesel is a renewable fuel and it is a sustainable fuel. The biodiesel can be derived from waste cooking oil (WCO) as it increases the commercial value of the WCO. The biodiesel has lower oxidation stability and hence onion oil which has good anti oxidation value was added with WCO biodiesel. The engine tests were carried with WCO biodiesel added with onion oil shows that the addition of onion oil improves the thermal efficiency and improvement in cylinder pressure and heat release rate. We conclude that the onion oil can be used as additive to the WCO biodiesel.

Supramolecular structure and thermal transformations of modified resinous-asphaltene substances

A detailed study of the supramolecular structure of high molecular weight resinous-asphaltene substances (RAS) and the study of their stability to thermal-oxidative degradation processes in the presence of surfactants is a promising scientific direction and can become the basis for the development of additional oil treatment processes and, as a result, the intensification of thermal transformations of oil dispersed systems (ODS). In the work it has been established that the maximum modifying effect, which consists in reducing the amount of asphaltenes by 8–11 % and increasing the concentration of resins, saturated and aromatic hydrocarbons in the composition of the dispersion medium, is achieved by the interaction of ODS with octadecylpropylenediamine, alkyldiamine with the content of ethoxylated groups n = 3–6 and butyl coconut fatty alcohol ester with n = 10. This fact is due to a change in the geometric parameters of asphaltene nanoaggregates due to the adsorption of these surfactants on their surface. Thus, against the background of an increase in the interplanar distances of condensed aromatic layers dm from 3.66 to 3.85 Å and values of the intrachain distance from 5.71 to 5.80 Å, the average diameter of aromatic layers decreases by 0.67–2.36 Å and the average height of their pack by 1.52–2.64 Å, while the average number of layers in a pack is 5. Estimation of the results of thermal analysis indicates that the RAS thermograms have a similar form with three endoeffects with minima in the ranges of ~ 34.7–37.7 °C (I); 325.7–339.3 (II) and 434.8–438.7 °С (III) and one exoeffect with a maximum of ~ 460.5–475.3 °С (IV). With a decrease in the factor of crystallinity and aromaticity of RAS, their resistance to the processes of thermo-oxidative degradation in the temperature region of coke formation increases. The energy of thermal-oxidative destruction for modified systems by surfactants exceeds by 21.6 kJ/mol of this indicator for unmodified RAS and is 62.07 ÷ 66.13 kJ/mol.

Superlubricity of multilayer titanium doped DLC coatings by using low SAPS organic additives in base oil

This study systematically investigates the tribological performance of titanium doped diamond-like carbon monolayer and multilayer coatings with superior mechanical properties. The coatings were lubricated in poly alpha olefin grade 4 (PAO4) base oil, containing three concentrations of two organic, ashless, and sulfur free (low SAPS) antiwear, and extreme pressure additives with different amounts of phosphorus and nitrogen (Duraphos® 178 and Duraphos® OAP). The multilayer Ti-doped DLC coatings exhibited superior tribological performance compared to uncoated steel, undoped DLC, and monolayer Ti-DLC coatings. They exhibited coefficient of friction values which were in the range of 0.013 and 0.006 (superlubricity) for formulations with Duraphos® OAP. Duraphos® 178 significantly lowered the specific wear rates of both the monolayer and multilayer coatings.

CO 2 geological storage potential in the Croatian part of the Pannonian Super Basin

In the continental part of Croatia oil and gas were discovered in more than 60 locations. Most reservoirs are in the Neogene/Quaternary basin infill, but the largest ones are found in the basement rocks. Decades of exploration left a significant vintage data set and substantial knowledge of the subsurface geology and reservoir properties. Since 2005 the research efforts were redirected to CO 2 geological storage capacity estimates and the first results were obtained relatively quickly. All identified potential storage objects: the deep saline aquifers (DSA), depleted hydrocarbon fields (DHF) and the oil reservoirs that are suitable for CO2-EOR can be regarded as prospective. DSAs are defined on a regional scale and their estimated capacity is the highest (2,584 Gt), but this is “theoretical capacity” that can only be used to outline the total resource base. The storage capacity estimated for the selected 14 DHFs sums up to 143,6 Mt and this is a viable capacity that might be developed as soon as particular field stops with production, but the most promising storage objects are the 7 fields that have reservoirs suitable for CO2-EOR operations. The most recent models have revealed that 7 active EOR fields operating in parallel between 2025-2040 could store up to 12.4 Mt CO2/year, while producing approximately 12.4 Mt/year of additional oil. This is very high for a country with only 5.5 Mt CO2/year in point sources.

A low-cost, antimicrobial aloe-alginate hydrogel film containing Australian First Nations remedy ‘lemon myrtle oil’ (Backhousia citriodora) – Potential for incorporation into wound dressings

Chronic wounds pose a global public health challenge, particularly in remote settings where access to specialised wound care and dressings can be limited and cost-prohibitive. First Nations communities in Australia are at a significantly higher risk for developing chronic wounds and this risk further increases for people living in remote regions. There is an urgent need to develop inexpensive but effective wound dressings to improve wound outcomes. Over the past decade, sodium alginate (SA)-based hydrogel polymers have emerged as a cost-effective and biocompatible component in wound dressings, and many have been successfully commercialised. In this study, we have developed and evaluated various prototypes of SA-based hydrogels with the addition of another low-cost component, aloe vera (AV) to further tailor the physicochemical properties of the hydrogel. Since the presence of microbes is a major contributor to the pathophysiology of chronic wounds, we also evaluated the antimicrobial activity of lemon myrtle oil (LMO) (Backhousia citriodora) incorporated into the hydrogel, a remedy used traditionally by First Nations Australians. Novel formulations of AV-SA-LMO hydrogel prototypes in the absence and presence of lemon myrtle oil (at a concentration of 5 μg/mL) were assessed for their physicochemical and antimicrobial properties and compared to a commercially available hydrogel-based dressing. The addition of lemon myrtle oil imparted viscoelastic behaviour for improved processability of AV-SA-LMO hydrogel prototypes, while increasing protein adhesion, enhancing physical properties, and demonstrating antimicrobial activity against the common wound-infecting microbes Staphylococcus epidermidis and Candida albicans. Fourier transmission infrared (FTIR) spectra confirmed the molecular structures of the hydrogel prototypes as predicted. The prototypes also demonstrated biocompatibility with the HaCaT human keratinocyte cell line. This study has provided preliminary evidence that a 25:75 aloe vera:sodium alginate hydrogel with 5 μg/mL lemon myrtle oil has comparable physicochemical characteristics to a commercial hydrogel-based wound dressing and antimicrobial properties against S. epidermidis and C. albicans.

Shape memory and mechanical properties of ESO modified epoxy/polyurethane semi-interpenetrating polymer networks for smart plaster

While numerous studies have explored the potential of shape memory materials in medical applications, the current research output is not enough for significant productivity in industrial products. In this research, a type of shape memory orthopedic plaster was fabricated by using epoxy/polyurethane interpenetrating networks modified with epoxidized soybean oil (ESO) and then compared with some commercial plasters. Polymer networks that were produced could be tailored to have glass transition temperatures (Tgs) within the range of 70–90 °C by changing the percentage composition of polyurethane and soybean oil. Shape recovery and fixity ratios in all samples were above 95 and 97 %. DMA results showed that IPNs with variable amount of soybean oil had lower glass transition temperature (Tg) and cross-link densities compared to IPNs without soybean oil. Based on the tensile test results, most samples exhibited an elastic modulus in the range of 280–400MPa, a level deemed somewhat acceptable when compared to commercial samples. Light microscope images had shown that the increase of polyurethane led to the phase separation of polymers, which was improved by the addition of soybean oil.

ФИЗИКО-ХИМИЧЕСКИЕ СВОЙСТВА МОДИФИЦИРОВАННЫХ БИТУМНЫХ ПРАЙМЕРОВ ДЛЯ ПРОТИВОКОРРОЗИОННОЙ ЗАЩИТЫ СЕЛЬСКОХОЗЯЙСТВЕННОЙ ТЕХНИКИ И ОБОРУДОВАНИЯ

Compositions based on bitumen primers can be used for anti-corrosion protection of agricultural machinery and equipment. Their physicochemical properties were studied. It has been shown that the thickness of coatings, which is responsible for the effectiveness of barrier protection, increases as expected with an increase in the number of applied coating layers, and decreases even with a slight increase in temperature and with an increase in the amount of solvent in the case of coating by dipping. Increasing the amount of solvent added to the bitumen primer from 40 wt. % up to 67 wt. % leads to a reduction in coating thickness by 55 times. Brush application produces thinner finishes than dip application. Moisture absorption for modified BP with 67 wt. % solvent is 1-2 orders of magnitude higher than that of BP with 40 wt. % white spirit, therefore, a decrease in protective effectiveness can be expected for these materials. According to experimental studies, the contact angles for the original BP exceed 900C, which indicates the presence of hydrophobic properties. The type and concentration of additives affect the contact angles. Introduction 5 wt. % of modifying additives, paraffin P2 and Emulgin, reduces the contact angle of BP, the addition of KO-SZhK, on the contrary, increases it, improving hydrophobic properties. BP with 40 wt. % white spirit, including those with additives, shows good adhesion to carbon steel 0.8 kp. At 67 wt. % solvent in the presence of drying oil and unrefined sunflower oil additives, adhesion worsens. Viscosity-temperature dependences in semi-logarithmic coordinates for modified BP are close to linear in the temperature range 20 -60 0C with a high approximation reliability index R2 = 0.9543 - 0.9833. Based on the physicochemical properties, high anti-corrosion properties can be assumed.

The tribological properties and synergistic lubrication mechanism of MoS2/AlOOH nanosheets as lubricant additives

The MoS2/AlOOH nanocomposites were prepared through a facile one-pot hydrothermal method and subsequently employed as lubricating oil additives to improve the tribological properties of PAO4 base oil. The structure, composition, morphology, tribological properties, and lubrication mechanism of the MoS2/AlOOH nanocomposites have been investigated. The results demonstrated that the in-situ assembly of MoS2 on the surface of AlOOH change their microstructure, resulting in enhanced dispersion and a reduction in friction and wear. At 0.5 wt% concentrations of MoS2/AlOOH nanocomposites, the average COF, WSD, and wear volume were decreased by 50.47 %, 42.34 %, and 86.57 % compared to base oil, respectively. Moreover, the tribological behaviors of the PAO4 containing MoS2/AlOOH nanocomposites under various conditions were explored as well. Furthermore, based on the analysis of micromorphology and composition of wear surfaces, a synergistic lubrication mechanism for MoS2/AlOOH nanocomposites has been proposed, which involves the formation of a tribochemical film composed of Fe2O3, Fe3O4, MoS2, and Al2O3 and demonstrates remarkable capabilities in reducing friction and wear. This research might provide new insight into enhancing the tribological properties of MoS2-based additives through the composite method and promote the application of MoS2/AlOOH nanocomposites as additives.

Films of polylactic acid with graphene oxide-zinc oxide hybrid and Mentha longifolia essential oil: Effects on quality of refrigerated chicken fillet

This study was conducted to investigate the morphological, thermal, mechanical, FTIR, physicochemical (thickness, humidity, solubility in water and water vapor permeability) and antimicrobial properties of polylactic acid film (PLA) containing hybrid graphene oxide‑zinc oxide (GO-ZnO: 1.5 % w/v) and Mentha longifolia essential oil (ML:1 % v/v) on chicken fillet kept in the refrigerator. The studied groups were microbially (total count of mesophilic aerobic bacteria, psychrotrophic bacteria, Enterobacteriaceae, Staphylococcus aureus, and lactic acid bacteria), chemically (pH, TVB-N) and sensory (color, odor, and taste) evaluated at 8-day interval (0, 2, 5 and 8). In the examination of the morphological characteristics, the PLA film had a smooth and uniform surface and the addition of ML essential oil created a discontinuous structure and the addition of GO-ZnO led to the production of a denser and more homogeneous film. The presence of GO-ZnO increased the thickness, decreased moisture content and solubility in water, and added ML essential oil increased moisture content and decreased solubility in water (p˂0.05). The results of the mechanical evaluation showed that the addition of ML essential oil and GO-ZnO reduced elongation at break and tensile strength (p˂0.05). The addition of ML essential oil increased the thermal resistance and the addition of GO-ZnO decreased the thermal resistance compared to the film containing ML essential oil. The antimicrobial effect of films containing ML essential oil was confirmed in this study (p˂0.05). The addition of GO-ZnO did not change the count of any of the microbial groups. TVB-N showed that groups containing ML essential oil had lower levels of volatile nitrogenous bases than the control group (p˂0.05). Sensory evaluation of the studied groups showed that chicken fillets packed with films containing ML essential oil had the highest score in terms of color, smell and taste. The results of the present study showed that PLA film containing GO-ZnO and ML essential oil can be used to increase the shelf life and maintain the sensory characteristics of chicken fillets, and it can be used as a suitable packaging to increase the shelf life of food products.

Effect of beeswax and coconut oil as natural coating agents on morphological, degradation behaviour, and water barrier properties of mycelium-based composite in modified controlled environment

Non-degradable coatings made of petroleum-based plastics hinder the degradation performance of products. This highlights the urgent need to develop biodegradable, bio-based coatings derived from renewable resources to create a more sustainable and greener world with a smaller environmental footprint. This study endeavours to examine the effects of beeswax and coconut oil additions on the morphological, degradation, and water-barrier properties of mycelium-based composite (MBC). Coconut oil is supplemented with varying amounts of beeswax, comprising 0, 20, 40, 60, 80, and 100 wt%. Dip coating is applied to prepare coated-MBC at 65 °C for 2 min. The coated-MBC is characterized by water absorption test, water loss measurement, density measurement, yeast and mould test, shrinkage measurement, weight loss measu rement, soil burial test, Scanning Electron Microscopy (SEM) and macroscopic appearance. Findings revealed that a higher composition of beeswax (80 BW) leads to lower water absorption ability (26.25 %) and no fungal growth for 36 days, in contrast to uncoated-MBC (0 BW), which are used as a reference sample.

Rapid and accurate detection of cinnamon oil adulteration in perilla leaf oil using atmospheric solids analysis probe-mass spectrometry

Perilla leaf oil (PLO) is a global premium vegetable oil with abundant nutrients and substantial economic value, rendering it susceptible to potential adulteration by unscrupulous entrepreneurs. The addition of cinnamon oil (CO) is one of the main adulteration avenues for illegal PLOs. In this study, new and real-time ambient mass spectrometric methods were developed to detect CO adulteration in PLO. First, atmospheric solids analysis probe tandem mass spectrometry combined with principal component analysis and principal component analysis-linear discriminant analysis was employed to differentiate between authentic and adulterated PLO. Then, a spectral library was established for the instantaneous matching of cinnamaldehyde in the samples. Finally, the results were verified using the SRM mode of ASAP-MS/MS. Within 3 min, the three methods successfully identified CO adulteration in PLO at concentrations as low as 5% v/v with 100% accuracy. The proposed strategy was successfully applied to the fraud detection of CO in PLO.

Dual surface-modification by oleic acid and epoxy-based silane coupling agent providing cerium oxide nanoparticles as additive in pentaerythritol oleate with improved high-temperature adsorption performance and tribological properties

An epoxy-based silane coupling agent (KH560) was grafted onto the surface of oleic acid-modified cerium oxide (CeO2-OA) nanoparticles in order to improve the competitive adsorption ability of the anti-wear additives in ester oils and simultaneously hinder the additive desorption owing to thermal disturbance under high-temperature condition. The as-prepared oleic acid-epoxy silane co-modified cerium oxide (CeO2-OA/E) nanoparticles were characterized. The effect of temperature on the adsorption behavior of trityl phosphate (TCP, a commercial high-temperature antifriction agent), CeO2-OA and CeO2-OA/E in PETO was studied using a dissipative quartz microbalance. Their tribological properties as the additives in pentaerythritol oleate (PETO), a polar ester base oil, were evaluated with a four-ball machine and a ball-on-block friction and wear tester; and their tribomechanism was explored with respect to their adsorption behavior on rubbed steel surfaces at elevated temperatures. It was found that the secondary surface-capping of CeO2-OA by the KH560 silane coupling agent resulted in great increases in the surface potential (from 54 mV to 396 mV) and thermal stability as well (the thermal decomposition temperature rose from 185 °C to 254 °C). Among the tesetd lubricant additives, CeO2-OA/E exhibited the highest adsorption mass, because of the highest surface potential the chemisorption ascribed to the epoxy group of the silane coupling agent. Particularly, CeO2-OA/E added in PETO exhibited better friction reduction and anti-wear properties at 150 °C than CeO2-OA and TCP, because CeO2-OA/E added in PETO formed tribofilm composed of CeO2 and SiO2 with excellent thermal stability as well as friction-reduction and antiwear effects through stable chemical adsorption and tribochemical reaction at elevated temperatures.

A green approach to synthesize polybutene lubricants from mixed C4 monomers using supported dendritic ionic liquids

Lubricants, composed of a base oil and various additives, reduce friction and abrasion between moving surfaces. High-performance lubricants, especially in the automotive and space industries, have driven advancements in synthetic oils like polyalphaolefins (PAOs), known for their high viscosity index and stability. Low molecular weight polyisobutylenes (PIBs) are used in multiple applications, including as viscosity improvers. PIBs are produced via cationic polymerization of isobutylene using Lewis acid initiators and co-initiators, often conducted at low temperatures with harmful substances like BF3. Efforts are being made to develop more eco-friendly processes, such as using AlCl3 and ionic liquids (ILs). In this research, boehmite-supported dendritic ILs (Gen1 and Gen2) were synthesized and tested as co-initiators in Raffinate-1 polymerization. The ILs improved the stability of the catalytic system, allowing for reduced AlCl3 usage, and produced PIBs with desirable molecular weight and viscosity characteristics. Density Functional Theory calculations unveiled the importance of the interaction of AlCl3 with the ionic liquids.

Oil Adulteration Evaluation Using High Performance Thin Layer Chromatography

Assessment of food authenticity from upstream in the supply chain is critical for the food industry. Environmental challenges and geo-political situations are causing shortages of raw materials resulting in a potential risk for food fraud. An example of this issue is the adulteration of edible oils by the addition of low-price oil, frying oil, or even non-edible grade oils mixtures threatening foods industries, consumer safety, and trust. Reliable screening tools to assess raw materials authenticity are therefore needed. Assessment of an improved alternative approach using high performance thin layer chromatography (HPTLC) is shown as a tool to evaluate edible oil authenticity and adulteration. Two methods were tested including an untargeted method based on fingerprints profiling for detection of adulteration with vegetable oil and a targeted method for mineral oil adulteration detection (e.g., paraffin wax). Statistical analysis was applied to determine acceptance criteria range to assess variability, limit of adulteration detection, and reproducibility. The robustness of the method was tested within an interlaboratory study using palm oil. Detection of adulteration with edible oils was achieved at levels from 5 to 25% while < 5% was predicted for mineral oils adulteration. Both methods showed promising results in terms of adulteration detection capability making this approach a reliable, and efficient tool to assess and monitor edible oils quality with added value in the field.

Comparison of Eco-Friendly Ionic Liquids and Commercial Bio-Derived Lubricant Additives in Terms of Tribological Performance and Aquatic Toxicity.

Approximately half of the lubricants sold globally find their way into the environment. The need for Environmentally Acceptable Lubricants (EALs) is gaining increased recognition. A lubricant is composed of a base oil and multiple functional additives. The literature has been focused on EAL base oils, with much less attention given to eco-friendly additives. This study presents the tribological performance and aquatic toxicity of four short-chain phosphonium-phosphate and ammonium-phosphate ionic liquids (ILs) as candidate anti-wear and friction-reducing additives for EALs. The results are benchmarked against those of four commercial bio-derived additives. The four ILs, at a mere 0.5 wt% concentration in a synthetic ester, demonstrated a 30-40% friction reduction and >99% wear reduction, superior to the commercial baselines. More impressively, all four ILs showed significantly lower toxicity than the bio-derived products. In an EPA-standard chronic aquatic toxicity test, the sensitive model organism, Ceriodaphnia dubia, had 90-100% survival when exposed to the ILs but 0% survival in exposure to the bio-derived products at the same concentration. This study offers scientific insights for the future development of eco-friendly ILs as lubricant additives.

Physicochemical characterization of novel okra mucilage/hyaluronic acid-based oral disintegrating films for functional food applications

Oral disintegrating films (ODFs) offer a patient-friendly approach with enhanced convenience and rapid onset of action over various health benefits. ODFs are fabricated for geriatric, pediatric, and individuals facing swallowing challenges. The present work aims to fabricate and characterize ODFs mainly composed of okra mucilage (OM), hyaluronic acid (HA), vitamin-C-loaded bioactive glass nanoparticles (VBG NPs), and clove essential oil. A bio-inspired method was employed to synthesize VBG NPs using fructose template. The nutrient analysis of OM depicted that it is a rich source of protein, carbohydrates, magnesium, and flavonoids (quercetin), accounting for its antioxidant activity. The physicochemical characteristics of the ODFs studied using contact angle measurement, surface pH, opacity, and in vitro disintegration time revealed that ODFs disintegrated rapidly in simulated saliva. The neutral surface pH of ODFs indicates their non-irritant behaviour to the oral mucosa. VBG NPs and essential oil (EO) addition enhance the thermal and mechanical properties. Further, EO infusion in the film matrix resulted in the porous and antibacterial nature of the functional film as revealed by FE-SEM micrographs and antibacterial disk diffusion assay respectively. The obtained novel nutrient-rich ODF is hemocompatible with a hemolysis rate (HR%) <5 % and suitable for functional food applications.