Power Filter Research Articles

Analysis of partial load loss of the PCS and internal storage battery loss in residential PV power generation and storage battery systems

AbstractThis study aims to quantify the amount of loss due to partial load of power conditioning system (PCS) and internal loss of storage battery in residential photovoltaic (PV) power generation and storage battery system by using home energy management system (HEMS) data. After identifying the configuration of the PV power generation and storage battery system, HEMS data on PV power generation, household demand, storage battery charging, storage battery discharging, purchased power and sold power were extracted and analyzed according to the research purpose. As a result, the loss due to partial load of the PCS and the average internal loss of the storage battery were quantified. In addition, it was confirmed that a more realistic system simulation could be performed by considering the impact of the partial load of the PCS and the average internal loss of the storage battery.

Solar Photo Voltaic Connected Quasi Z Source Inverter for Grid and utility Application

This paper discusses the use of quasi-Z-source inverters, in utility grid systems. These inverters enhanced dependability and one-stage buck and boost abilities make them appropriate for photovoltaic power conditioning applications. The small signal sate space method utilized for the proposed system using Quasi ZSI for utility and grid integration application. Shoot through state also implemented on dc side to enhanced the voltage gain. The Controlling of dc side and ac side also implemented in MATLAB using state space transfer function. A two-stage controlling technique implemented on two level 6 switch inverters with SPWM with P & O MPPT and PI controller. The proposed system has solar PV array rating of 5.5kW and utilized in distribution purpose. A simple boost controlling technique has been implemented to obtained the desired gain and less ripples are present in the current due to the presence of inductor in the QZSI impedance network. During light loading the surplus power injected to the grid with the help of PLL system and when load demand increases the power take from the grid smoothly without loss of synchronism. The system has better stability and fast dynamic response during transient. The THD has been observed at the inverter and load side with LC filter, THD within the permissible limit as per IEEE std 1547.

Smart Home Powered by Solar: IoT-based SEPIC Converter Control

Background: In this article, an IOT solution for managing and controlling a PV system with applications for the home is presented. A DC-DC SEPIC converter, a bidirectional converter, a PWM generator, and a single-phase voltage source inverter with active clamping are used for power conditioning. An output voltage control loop is implemented, and real-time online communication with an internet server is accomplished using the PIC microcontroller. Methods: The ESP8266MOD WIFI IOT module works with the Blynk mobile app. Experimental findings showing the proper operation of IOT features demonstrate the effectiveness of voltage regulation. In this article, frequency is taken into consideration as solar power is integrated with the grid. A user may easily control the DC-DC converter, load batteries, and monitor battery voltage through our userfriendly GUI interface. Results: In this paper, an IOT (Internet of Things) application was used to control and track the output of a modest PV power plant. The study shows the efficiency of the digitally controlled system developed to regulate the output voltage of the SEPIC DC-DC converter. Practical Significance: They further argue that the ESP8266 and microcontroller's versatility make them an appropriate instrument for remote and real-time monitoring and control of the proposed model from around the world. The energy that is produced by the sun is added to the grid so that it may be put to effective use and contribute to satisfying the rising demand for energy. Solar energy is the input that SEPIC uses to charge the batteries and for all of its other processes. In the event that solar photovoltaic (PV) panels are not available, the SEPIC DC-DC converter will derive its energy from AC power. Conclusion: In this article, an IOT (Internet of Things) application was used to control and track the output of a modest PV power plant. The research demonstrates the effectiveness of the digitally controlled system created to manage the output voltage of the SEPIC DC-DC converter. They further argue that the ESP8266 and microcontroller's versatility make them an appropriate instrument for allowing remote and real-time monitoring and control of the proposed model from any part of the world. The energy that is produced by the sun is added to the grid so that it may be put to effective use and contribute to satisfying the rising demand for energy. Solar energy is the input that SEPIC uses to charge the batteries and for all of its other processes. In the event that solar photovoltaic (PV) panels are not available, the SEPIC DC-DC converter will derive its energy from AC power.

Evolving Power Factor Correction in Solar Water Pumping Systems through Zeta Converter-Based BLDC Motor Drives

The aim of this paper is to present the design and implementation of a new power conditioning system for a stand-alone solar-powered water pumping system. The system integrates a Brushless DC (BLDC) motor drive with a Power Factor Correction (PFC) Zeta converter to improve energy efficiency and reliability. In order to power BLDC motors for water pumping applications—which are essential for irrigation in isolated locations without access to the grid—the suggested solution attempts to overcome the difficulties related to the direct use of variable solar power. The PFC Zeta converter, which is the system's central component, is made to maximize power extraction from photovoltaic (PV) panels under fluctuating solar irradiation, guarantee high power factor, and reduce harmonic distortion in the electrical grid. A BLDC motor that powers a water pump is efficiently operated by this converter, which also optimizes the DC link voltage. A BLDC motor is especially well-suited for solar-powered applications due to its increased efficiency, dependability, and longer lifespan when compared to traditional induction motors. In order to continuously modify the PV panels' operating point to the maximum power point and maximize the amount of energy they capture, a Maximum Power Point Tracking (MPPT) algorithm is incorporated into the PFC Zeta converter's control strategy. The BLDC motor drive control strategy is carefully designed to guarantee seamless operation and flexibility in response to the fluctuating output from the solar panels, upholding the best possible pumping action in any solar situation. The system's capacity to sustain high efficiency and power factor under a variety of operating circumstances is demonstrated by the experimental findings. When the PFC Zeta converter is used, the solar-powered water pumping system performs much better overall. It shows a notable increase in energy conversion efficiency and lowers total harmonic distortion, which prolongs the pumping system's lifespan. By offering a solid method for raising the effectiveness and dependability of solar-powered water pumping devices, this study advances the sector and holds the possibility of a long-term water supply option for agricultural irrigation in isolated locations. In addition to utilizing renewable solar energy's environmental advantages, the suggested solution tackles the real-world difficulties associated with putting dependable and effective water pumping equipment into off-grid applications.

Performance analysis of three-phase solar PV, BESS, and Wind integrated UPQC for power quality improvement

UPQC (Unified Power Quality Conditioner) is indeed a Versatile power conditioner which could be utilized to adjust for a variety of power supply voltage disturbances, rectify voltage fluctuation, and minimize harmonic load current in accessing the power source. To ensure a continuous power supply. We are making use of UPQC technology in combination with shunt and series AFC (Active filter compensators) to counteract power quality problems resulting from grid harmonics and nonlinear loads. Therefore, the focus of this research is to analyze the UPQC's system performance under swell and sag with the variation of solar irradiation and temperature. To achieve these two distinct cases of PV system like temperature-25 °C, irradiance-700 W/m2, and temperature-45 °C, irradiance-800 W/m2, are considered respectively. The implementation of the FOPI controller purposes to bolster power quality of 3-phase HESS (hybrid energy storage system), which includes an integrated UPQC for outstanding performance. In order to manage harmonics resulting from non-linear loads and reduce grid power quality issues, the UPQC model integrates both shunt and series AFC. In the case of extended voltage interruptions, the integrated UPQC with BESS, wind and PV can effectively resolve power quality concerns. The UPQC shunt compensator efficiently harnesses power from HES (hybrid energy systems), whereas the series compensator acts as a guardian, protecting the load from power quality issues originating in the grid. In order to regulate the voltage of the DC connection at a desired level, the aim of this article is to develop a FOPI controller with isodamping properties. In particular, a novel hybrid algorithm called the Enhanced Seagull with Rooster Update (ES-RU) Algorithm, which combines the ideas of Chicken Swarm Optimization (CSO) and Seagull Optimization algorithm (SOA), optimally tunes the gain of the FOPI controller. For optimal performance, the FOPI controller's gain parameters (Kp, Ki, λ) are finely tuned using an Enhanced Seagull with Rooster Update (ES-RU) Algorithm. As a consequence, the performance of the adopted and extant models is examined during sag and swell conditions with respect to source voltage and load voltage and compared with other conventional models like PI, FF, CS and SG, respectively for both cases like temperature-25 °C, irradiance 700 W/m2, and temperature-45°C, irradiance-800 W/m2, correspondingly. The overshot and total harmonic distortion (THD) of the proposed ES-RU is superior to the existing models like PI, FF, CS and SG.

ABC-WOA Optimization Strategy for UPQC Fuzzy PI Tuning

Growing numbers of power electronics-based non-linear loads have raised worries about power quality (PQ) problems, which include equipment failures, overheating, and unplanned shutdowns. Power filters have traditionally been used for harmonics elimination, but their limitations in dynamic compensation and size present challenges. The present research presents a new methodology using the Artificial Bee Colony - Whale Optimizations Algorithm (ABC-WOA) to optimize the Unified Power Quality Conditioner (UPQC) controller. Assignment aims to tackle obstacles that come with it. The suggested algorithm's efficacy is clear, as shown from the stabilization of objective function values. Highlighting the expertise of the Proportional-Integral (PI) controller in effectively regulating the DC-link voltage, this study successfully addresses power quality concerns. The analysis of voltage injection emphasizes the significant influence of the controller on the power system, showcasing seamless integration and enhanced power quality. This research provides valuable insights into the application of advanced control algorithms in power systems, specifically in addressing challenges related to non-linear loads and transient conditions.

Integration of Piezoelectric Energy Harvesting Systems into Building Envelopes for Structural Health Monitoring with Fiber Optic Sensing Technology

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHSs) into building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective of leveraging structural health monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into a ventilated façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHSs is defined to provide a complete system for façade monitoring. This integrated system includes the piezoelectric generator (PEG), supercapacitor (SC), Power Conditioner Circuit (PCC), Fiber Optic Sensing (FOS) interrogator, and the IoT gateway transmitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector but raise issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHSs for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of piezoelectric energy harvesting technology in building envelope monitoring.

Design of Onboard Avionics Based on Commercial Off-the-Shelf Parts for TianQi-2 Nanosatellite

With the development of modern small satellite technology, short development cycles, low cost, and high reliability have become trends in the era of New Space. To achieve the above goals, an integrated centralized architecture of onboard avionics for an internet of things CubeSat was proposed, and CAN, I2C, and 1-wire buses were employed for telemetry collection and command sending. The implementation of onboard computers (OBCs) and the power conditioning and distribution unit (PCDU) was introduced based on the PC104 industrial standards. An arbitration switching strategy between the primary and backup OBCs was proposed so that the primary OBC had priority to be on duty. Over 98% of commercial off-the-shelf (COTS) parts were used to decrease costs, so a procedure for COTS part selection and a qualified method were presented for reliable application. The onboard avionics, including OBC and PCDU, were developed in six months, and the satellite has been in orbit for more than three years and still works well. The reliability of the onboard avionics developed using the philosophy of New Space is demonstrated by the three-year flight in orbit.

Optimal configuration of energy storage system capacity in traction power supply system considering photovoltaic consumption

In order to achieve energy savings and promote on-site integration of photovoltaic energy in electrified railways, a topology structure is proposed for the integration of photovoltaic (PV) and the energy storage system (ESS) into the traction power supply system (TPSS) based on a railway power conditioner (RPC). This paper analyzes the composition and operation principles of this structure. To assess the economic benefits brought by the integration of photovoltaic and energy storage systems, a bilevel optimization model is established, with the objectives of optimizing energy storage capacity configuration and photovoltaic energy integration. The KKT (Karush–Kuhn–Tucker) method is employed to transform the model into a single-layer mixed-integer linear programming model, which is then solved using the CPLEX solver in MATLAB. The research findings indicate that, with the configuration of the ESS, the optimal PV consumption rate achieved is 96.8749%. Compared to a 100% PV consumption rate, the ESS capacity configuration is reduced by 13.14%, and the overall operational cost of the TPSS is at its lowest. The study suggests that the proposed bilevel optimization algorithm can more effectively consider PV consumption, leading to enhanced economic performance of the TPSS operation.

An Algorithm for a Space-Vector Pulse Width Modulation with a Hybrid Switching Sequence for a Three-Level Neutral Point Clamped Voltage Source Inverter

This paper proposes a new algorithm for a space-vector pulse width modulation (SVPWM) with a hybrid switching sequence (SS) designed to control a three-level (3L) neutral point clamped (NPC) voltage source inverter (VSI). Based on the advantages of five-stage and seven-stage SS, we designed a hybrid SS to improve four key parameters in the system: inverter output current quality, neutral point (NP) and common-mode (CM) voltage levels, and switching losses of power switches. The proposed algorithm flexibly regulates meeting the four criteria depending on the system operating conditions by changing the regulation coefficient. The paper obtained an approximate dependence to determine the optimal regulation coefficient for any values of the inverter modulation coefficient when operating jointly with an active-inductive load. The effectiveness of the proposed algorithm is confirmed by computer simulation in the MatLab+Simulink environment, as well as the results of experimental studies. The paper presents the experimental dependences of static state spaces, including the distortion coefficient of higher current harmonics at the inverter output, the maximum error of the NP voltage, the number of switching pairs of power switches, and the pulse duty factor of CM voltage, depending on the inverter modulation coefficient and the regulation coefficient of the hybrid SS. The results showed that in the algorithm for a SVPWM with a hybrid SS, the number of switchings of power switches is reduced by an average of 13.5 % while maintaining the NP voltage balance and the quality of the curve at the inverter output at an acceptable level, close to a seven-stage SS (the deviations do not exceed 0.5 % and 0.2 %, respectively). The average CM voltage coefficient decreased by no more than 4.5 %. The indicators improve the energy saving, the weight-size parameters, and the operational reliability of the 3L NPC VSI. The application area of the algorithm is much wider and includes the control of power switches of active front ends, grid converters for electricity storage systems, active power filters, and power conditioners. DOI: https://doi.org/10.52783/pst.237

CVaR Quantitative Uncertainty-Based Optimal Dispatch for Flexible Traction Power Supply System

The flexible traction power supply system (FTPSS) integrating a photovoltaic (PV) generation system, an energy storage system (ESS), and a railway power conditioner (RPC) is a promising solution for future railways. However, the volatilities and random uncertainties of PV and traction load negatively impact the ability of FTPSS to operate safely and economically. A dispatch method combining conditional value-at-risk (CVaR) and probabilistic scenarios is proposed for FTPSS to quantify uncertainties into the risk cost. To reconcile economy and robustness, a flexible optimization dispatch model that considers the economic expense and risk cost is built. Finally, this optimization problem is formulated as a mixed integer quadratically constrained programming (MIQCP) model and solved by the GUROBI solver. Based on a genuine instance in China, the method’s validity has been demonstrated. The validity of the method is verified based on a real case in China. The essence of the proposed method is to mitigate the risks related to PV and traction load changes to some extent during the day-ahead dispatch stage by taking into account potential fluctuations in the real-time operating stage. The proposed method can help dispatch decision-makers create effective dispatch strategies and is conducive to FTPSS energy savings and risk avoidance.

Research on DC Voltage Stability Control of Railway Power Conditioner Based on Impedance Matching Principle

When the Railway Power Conditioner (RPC) is used to solve the power quality problem of the electrified railroad, the DC impedance will have a negative impedance characteristic during the bidirectional transmission of RPC power, and this negative impedance characteristic will affect the accuracy of RPC power compensation, cause the fluctuation of RPC DC bus voltage, and affect the effect of negative sequence current management on the grid side. In view of the above problems, this paper proposes an RPC control strategy based on the impedance matching principle, which optimizes the negative impedance characteristics into positive impedance characteristics by the cooperative control of DC voltage and power, increases the phase angle margin of the system, improves the stability and dynamic performance of DC voltage under the bidirectional flow of RPC power, and improves the effect of grid-side negative sequence current management. Firstly, this paper performs small-signal modeling of the DC-side port impedance and analyzes its impedance characteristics. Secondly, the working principle of the RPC control strategy based on the impedance matching principle is analyzed. Finally, the proposed control strategy is effectively verified by building a simulation model and an experimental platform.

Fault-Tolerant Method of Modular Railway Power Conditioner Based on DC Bus Voltage Regulation

With the development of high-speed electrified railway, many serious power quality problems have arisen and caused widespread concern. In order to achieve comprehensive management of power quality, modular railway power conditioner (MRPC) has been applied to traction systems. However, due to the presence of multiple sub-modules (SMs). The reliability of the equipment is threatened as the number of SMs increases. In medium-voltage applications, system reliability can be improved by adding redundant SMs. However, when the redundant SMs are run out, the reliability of the whole system cannot be guaranteed. Therefore, a fault-tolerant method based on DC bus voltage regulation is proposed to improve the reliability of MRPC by modulation signal reconstruction. The proposed method not only achieves fault ride-through to maintain normal operation and improves the SMs voltage stress on the opposite converter, but also effectively improves the over-modulation. The effectiveness of the proposed method is verified by down-scale experiments.

State of the Art on Power Conditioning for Piezoelectric Energy Harvesters

State of the Art on Power Conditioning for Piezoelectric Energy Harvesters

Enhancing grid‐connected solar PV systems with a novel three‐phase hybrid multilevel inverter

SummaryThis paper presents a novel three‐phase hybrid multilevel inverter (TPHMLI) designed for grid‐connected solar photovoltaic (SPV) systems. The TPHMLI combines series‐connected bridge topologies of half and full circuits to generate 11 stages of line load voltages, reducing the need for DC sources. It also introduces an improved pulse width modulation (PWM) approach, addressing computational challenges and high‐frequency triggering issues. Practical validation in a laboratory setting demonstrates the MLI's functionality and effectiveness. Furthermore, the advanced MLI topology successfully addresses design issues in grid‐integrated SPV structures, including power quality, efficiency, and reliability. It excels in managing reactive power and fault obstructive capabilities. Extensive simulations using MATLAB/Simulink confirm its superior performance, making it a promising solution for power conditioning units in grid‐connected solar PV systems. This research contributes to clean and sustainable energy conversion technologies, enhancing power quality and cost‐effectiveness, with significant potential for practical applications in the renewable energy sector.

Analysis of single phase ZSI fed PV system in weak grids using fractional order sliding mode control technique

Nowadays, Photovoltaic (PV) system’s contribution to the power grid is increasing immensely. The PV system is linked with power grid through one or more inverters and a power conditioning unit to ensure smooth power delivery while also maintaining system voltage and frequency stability. However, due to grid load expansion, weak power grids have emerged as the dominant one today. As a result, the voltage and frequency of the grid got distorted. It may cause serious damage to the entire system in some cases. A single phase ZSI with the proposed Fractional order SMC technique is used to address these issues. The single phase ZSI consists of only two power switches and perpetuates the voltage transfer ratio like full bridge inverter. It also corroborates the sharing of power, regulatesactivepower,voltage, frequency, reactive powerand alleviates the harmonics in current. The input voltage of inverter is boostedby using theshoot through state and it also improvesthe reliability of inverter. The execution of the single phaseZSI withproposed FOSMCtechnique is assessed in MATLAB/Simulink to bear out the magnificent features of the proposed FOSMC in weak grid.

An adaptive controller for power quality control in high speed railway with electric locomotives with asynchronous traction motors

Introduction. Power quality in an electric railway system pertains to the dependability, consistency, and purity of the electrical power provided to different components and systems within the railway infrastructure. Assessing power quality offers considerable opportunities to improve the efficiency of railway systems. Problem. Managing the flow of active and reactive power effectively, decreasing harmonic currents, and addressing the negative sequence component are all critical parts of improving power quality for electrified rail systems. As a result, flexible AC transmission systems are the major means of minimizing or decreasing these difficulties. Purpose. This study describes a half-bridge reactive power railway power conditioner (HB-RPC) with a novel Ynev balancing transformer. HB-RPC is made up of four switching devices and two DC capacitors and the compensator’s stability is determined by the operating voltage of the DC-link. Any variations or imbalances in the DC voltage might cause the compensator to operate in an unstable manner. Novelty. Of a novel balanced transformer with HB-RPC in a high-speed railway system with two scenarios. Methods. The study utilized MATLAB/Simulink software for simulation purposes. The system integrates a fuzzy logic controller (FLC) and a PI controller to optimize DC voltage, ensuring its constancy and balance, with the objective of improving the overall stability of the system. Results. The simulation outcomes illustrate the efficacy of the control approach. Through a comparison of results between scenarios (two and four trains) with the PI-based-HB-RPC and the FLC-based-HB-RPC, the system exhibits enhanced stability for the proposed railway system when employing the FLC-based-HB-RPC, compared to a controller based on PI. Practical value. The proposed configuration elucidates its role in enhancing both the dynamic performance of the system and the power quality of the three-phase rail traction chain.

Assessment of unbalance and distortion in power systems that include active power line conditioners.

This paper presents a decomposition of the apparent power of a system that allows to separate the contribution to the unbalance of the whole set of harmonics of voltages and currents. From this set of power terms, the unbalanced fundamental, balanced harmonics and unbalanced harmonic indices are derived, that allow to evaluate separately the distortion and the unbalance. This procedure gives a more appropriate way to characterize the mitigation obtained using modern equipments with active compensation. These new indicators of the electric power quality have been applied here to a system with unbalance and distortion in the supply and the load, before and after the connection of a parallel active compensator, and with the connection of a series-parallel active compensator. The results obtained with a dedicated experimental platform have allowed to verify the validity of the new proposed indices.

Smart Grid Operation with Hybrid Renewable Resources and Electric Vehicle

The utilization of renewable energy resources will significantly increase to achieve clean and sustainable electricity generation. The management of the continuous growth share of variable renewable resources, integration of electric vehicles (EVs) and regulation of grid frequency require effective communication facilities of recent smart grids. In this respect, smart converters can provide efficient power conditioning devices to extract maximum power from renewable resources. In addition, the batteries of EVs could be used as distributed storage and discharge power back into the grid to compensate power deficit and flactuation. Modeling and controlling of the hybrid resources within smart grid were carried out in this paper. The smart converter is switched to track the maximum power point MPPT of the solar panels. In addition, the pitch angle control and DFIG regulation are used to extracte the maximum power under different wind speed and tidal stream velocities. The deployment of EVs can compensate power fluctuations and regulate the frequency deviations in the grid based on the proposed PID controller. In this paper, the integral minimization of time-weighted absolute error (ITAE) is used for on-line tuning of the PID controller parameters. Using Matlab/Simulink package, the smart grid is modeled and simulated using the weather data of Kuwait and then the grid performance is assessed under system disturbances and load excursions.

A Method for Power Conditioning with Harmonic Reduction in Microgrids

This paper presents a control method of Renewable Energy Sources (RES) to reduce the harmonic content of the distribution system to which are connected, such as a Microgrid. By this method the RES is acting as a Power Conditioner and its supplying system consists of a buck-boost converter connected back-to-back to a polarity swapping inverter. A RES or a Distributed Generator (DG) such as a microturbine is synchronized to the distribution system, which is assumed to be distorted by a high-order voltage harmonic. Utilizing the proposed method, the RES not only exports its output power to the grid, but also reduces the existing harmonic distortion, improving voltage quality at the Point of Common Coupling (PCC). Simulations in Matlab/Simulink platform have been performed in order to verify the effectiveness of the suggested approach to reduce harmonic content.