Plate Acoustic Waves Research Articles

Features of the Formation of Sensitive Films Based on Mycelium of Higher Fungi for Surface and Plate Acoustic Waves Gas Sensors.

A comparative analysis of the responses of two types of acoustic waves (surface SAW and plate APW) with close frequencies and the same type of waves (SAW) with different frequencies toward various liquid vapors (water, acetone, ethanol) was carried out in this paper. Two types of films based on mycelium of higher fungus Ganoderma lucidum (Curtis) P. Karst (G. lucidum) prepared by various methods were used as sensitive coatings. These films were based on G. lucidum mycelium ethanolic (48% v/v) homogenizate (MEGl) and extract (EGl). A film deposition procedure compatible with acoustic devices technology was developed. Various piezoelectric substrates (YX-LiNbO3, 128 YX-LiNbO3) were used for appropriate acoustic delay lines production. It was found that additional SAW and APW attenuation associated with the appearance of mycelium films on the surface of the acoustic waveguide is two times greater for MEGL than for EGL films in the frequency range of 20-80 MHz The changes in acoustic wave amplitude and phase due to vapor absorption were measured and compared with each other, taking into account the differences in geometry of the samples. It was found that the phase response of the SAW delay lines with EGL films is three times higher than one with the presence of MEGL films for water and ethanol vapors. The films used are demonstrated good reproducibility and long-term stability for at least 2 months. Based on the results obtained, it was concluded that MEGl film is not appropriate for use in high frequency SAW delay lines as a sensitive coating. However, both types of the films (MEGl and EGl) could be used as sensitive coatings for low frequency SAW and APW sensors based on corresponding delay lines. Additionally, it was found that the films used are not sensitive to acetone vapor. As a result of the work carried out, a technique for creating sensitive films based on the mycelium of higher fungi compatible with the planar technology of acoustoelectronic delay lines was developed. The possibility of using such films for the development of gas SAW and APW sensors was shown.

Backward Acoustic Waves in Piezoelectric Plates: Possible Application as Base for Liquid Sensors

Backward acoustic waves are characterized by oppositely directed phase and group velocities. These waves can exist in isotropic and piezoelectric plates. They can be detected using a set of interdigital transducers with different spatial periods located on the same piezoelectric substrate. In this paper, the effect of a nonviscous and nonconductive liquid on the characteristics of a first-order backward antisymmetric wave in a YX plate of lithium niobate is studied theoretically and experimentally. It is shown that the presence of liquid does not lead to the transformation or disappearance of this wave. It is shown that these waves are close to the cutoff frequency and are characterized by the presence of a point with zero group velocity. The design of a liquid sensor based on these waves is proposed.

High-Q Resonator–Inductor Using LiNbO₃ Plate for Frequency Tuning in 1–5 GHz

In this article, a new high quality factor ( Q ) inductor with piezoacoustic plate acoustic wave (PAW) resonators is presented. As indicated by the investigation of the acoustic wave propagation characteristics and transducer materials, the coupling coefficient ( k2 ) of the shear-horizontal plate (SH0) mode that propagates in the LiNbO3 plate increases to 55.7%, which leads to a wide inductive bandwidth of 29%. The longitudinal and transversal spurious modes are inhibited through novel edge reflector design and transducer engineering. The peak inductor quality factor ( [Formula: see text]) of the acoustic resonator-inductor is obtained as 347, and a large range of inductance values are achieved to be up to 49 nH by regulating the interdigital transducer (IDT) number of fingers (NF). It is noteworthy that a larger inductance is realized in a more miniaturized device. Furthermore, the wavelength-scaling-induced physics is investigated for frequency tuning in 1-5 GHz, which reveals the multifrequency ability on a single chip of the SH0 acoustic resonator-inductor.

Selective Detection of Liquid Viscosity Using Acoustic Plate Waves with In-Plane Polarization.

Using plates of weak piezoeletcric crystal (quartz) loaded with various liquids, it is shown that along with common modes, whose sensitivity towards different liquid parameters comparable with each other, there are some uncommon modes, whose amplitude responses towards viscosity η are much larger than towards temperature T and electric conductivity σ. The search of the modes with the selective properties is accomplished by varying plate thickness h, crystal orientation, wave length λ, and mode order n. It is found that all modes possessing the property are characterized by small surface-normal displacement, avoiding wave radiation into adjacent liquid, large in-plane displacements, enhancing viscous coupling the modes and liquids, and small electro-mechanical constant, reducing electro-acoustic interaction. Basing on the modes, the sensor prototypes with selective operation are developed and tested for η from 1 to 1500 cP, σ from 0 to 1.2 S/m, and t from 0 to 55 °C. Because of operation at ultrasonic frequency (tens MHz) the prototypes have different sensitivities in various η-ranges: 0.3 dB/cP for 1–20 cP, 0.12 dB/cP for 20–100 cP, and 0.015 dB/cP for 100–1500 cP. Viscosity responses of the prototypes become comparable with their electric outputs only for η < 2 cP. Temperature responses are almost zero in air, but when plate is coated with liquid they increase depending on liquid properties, allowing measurements of the temperature dependence of the liquid viscosity.

An Artificial Intelligence Approach to Fatigue Crack Length Estimation from Acoustic Emission Waves in Thin Metallic Plates

The acoustic emission (AE) technique has become a well-established method of monitoring structural health over recent years. The sensing and analysis of elastic AE waves, which have involved piezoelectric wafer active sensors (PWAS) and time domain and frequency domain analysis, has proven to be effective in yielding fatigue crack-related information. However, not much research has been performed regarding (i) the correlation between the fatigue crack length and AE signal signatures and (ii) artificial intelligence (AI) methodologies to automate the AE waveform analysis. In this paper, this crack length correlation is investigated along with the development of a novel AE signal analysis technique via AI. A finite element model (FEM) study was first performed to understand the effects of fatigue crack length on the resulting AE waveforms and a fatigue experiment was performed to capture experimental AE waveforms. Finally, this database of experimental AE waveforms was used with a convolutional neural network to build a system capable of performing automated classification and prediction of the length of a fatigue crack that excited respective AE signals. AE signals captured during a fatigue crack growth experiment were found to match closely with the FEM simulations. This novel AI system proved to be effective at predicting the crack length of an AE signal at an accuracy of 98.4%. This novel AI-enabled AE signal analysis technique will provide a crucial step forward in the development of a comprehensive structural health monitoring (SHM) system.

Higher-order Lamb waves with quasi-zero surface displacement components on a GaAs piezoelectric plate

Higher-order Lamb waves with quasi-zero surface displacement components are reported on (100)-cut GaAs propagating along the <110> direction where the total displacement at the surface of the plate is less than 10% of the maximum total displacement. The dispersion curves and the displacement component profiles show the reduction of total displacement at the surface of the plate starting when the phase velocities of the higher-order modes are crossing the shear bulk acoustic wave velocity to the value as low as 5%. Due to the concentration of acoustic energy inside the plate, the reported quasi-zero plate acoustic waves (QZ-PAW) further reduce the radiation of acoustic energy when the plate surface is in contact with liquid. The experimental results validate the occurrence of QZ-PAW with a reduction of viscous damping insertion loss compared to previously reported quasi-longitudinal Lamb waves. The results demonstrate the potential QZ-PAW mode for emerging applications such as dual-mode PAW sensors, PAW devices with integrated sensor and actuator, thin-film and ultra-high frequency PAW sensors in highly viscous liquid media.

An approach to adhesive bond characterisation using guided acoustic waves in multi-layered plates

Abstract An approach for the non-destructive characterisation of adhesive bonds using guided ultrasonic waves is presented. Pulsed laser radiation is used to thermoacoustically excite broadband ultrasonic waves in a multi-layered sample, consisting of a metal plate adhesively joined to a polymeric layer using synthetic resin. The resulting signals are received by a purpose-built piezoelectric transducer. Varying the distance between excitation and detection yields spatio-temporal measurement data, from which the dispersive properties of the propagating waves can be inferred using a two-dimensional Fourier transform, assuming the plates to act as coupled waveguides. Coupled multi-layered waveguides show an effect referred to as mode repulsion, where the distance between certain modes in the frequency-wavenumber domain is assumed to be a measure of coupling strength. Measurements at different stages of curing of the adhesive layer are performed and evaluated. A comparison of the results shows changes in the dispersive properties, namely an increased modal bandwidth for the fully cured sample as well as an increased modal distance.

Ultrasonic flow meter using mode coupling transducers

This paper describes the development of an ultrasonic flow meter using a new type of transducer called the mode coupling transducer (MCT). The mode coupling transducer consists of a thin plate of a suitable piezoelectric material on which an interdigital transducer (IDT) is deposited for the generation and detection of plate acoustic waves. The flow meter consists of two such transducers mounted on opposite walls of a pipe through which the fluid is flowing. The transducers used in this work were fabricated on 0.5 mm thick plates of lithium niobate and had a center frequency of 1 MHz. The prototype device developed here can measure flow rates over a range from less than 0.2 lpm (liters per minute) to greater than 100 lpm.

Effects of surface impedance on current density in a piezoelectric resonator for impedance distribution sensing

We study the relationship between the surface mechanical load represented by distributed acoustic impedance and the current density distribution in a shear mode piezoelectric plate acoustic wave resonator. A theoretical analysis based on the theory of piezoelectricity and trigonometric series is performed. In the specific and basic case when the surface load is due to a local mass layer, numerical results show that the current density concentrates under the mass layer and is sensitive to the physical as well as geometric parameters of the mass layer such as its location and size. This provides the theoretical foundation for predicting the surface impedance pattern from the current density distribution, which is fundamental to the relevant acoustic wave sensors.

Investigating peculiarities of piezoelectric detection methods for acoustic plate waves in material characterisation applications

Abstract Acoustic waves in plates have proven a viable tool for testing and material characterisation purposes. There are a multitude of options for excitation and detection of theses waves, such as optical and piezoelectric systems. While optical systems, with thermoelastic excitation and interferometric detection, have the benefit of being contactless, they usually require rather complex and expensive experimental setups. Piezoelectric systems are more easily realised but require direct contact with the specimen and usually have a limited bandwidth, especially in case of piezoelectric excitation. In this work, the authors compare the properties of piezoelectric and optical detection methods for broad-band acoustic signals. The shape (e. g. the displacement) of a propagating plate wave is given by its frequency and wave number, allowing to investigate correlations between mode shapes and received signal strengths. This is aided by evaluations in normalised frequency and wavenumber space, facilitating comparisons of different specimens. Further, the authors explore possibilities to utilise the specific properties of the detection methods to determine acoustic material parameters.

Influence of plate acoustic waves on electronic transport in nanowires

The acoustoelectric effect is the generation of a acoustoelectric current in a non-biased device by a piezoactive acoustic wave. This effect has recently attracted the attention of researchers as a possible method to control the motion of massive objects in the quantum regime. We suggest using this effect for development of highly sensitive nanoelectronic sensors. The sensitivity could be increased through the use of modulation mode of operation based on the acoustic pilot signal and the transition from quasi-stationary measurement to measurement at the modulation frequency. The acoustic delay line based on shear-horizontal acoustic wave of zero order (SH0) with resonant frequency 3.25 MHz in Y-X LiNbO3 plate was produced. The nanostructure consisting of nanowire with size 20 nm × 180 nm was placed in the center between IDTs. The current–voltage characteristics of this nanowire in the presence and absence of the acoustic wave were meazured by a picoampermeter. The analysis has shown that the presence of piezoactive acoustic wave is influenced by electric current in a nanowire.

Features of the Metallization Influence on Phase Velocities of Acoustic Waves in Piezoelectric Plates

The paper presents an analysis of the influence of the load represented by two metal layers on the change in the phase velocity of the dispersion modes of the elastic Lamb and SH-waves in "Me/ZnO/Me" and "Me/AlN/Me" structures depending on the elastic wave frequency and the ratio of the metal layer to the piezoelectric layer thickness. Aluminum (Al), molybdenum (Mo) and platinum (Pt) are considered as the metal layer materials (Me). Only the elastic Lamb wave modes have localized maxima of the sensitivity curve S for all types of structures. Systems with low values of acoustic impedances for layers and plates materials have maximum values of S for metallization with thin layers, and also have minimal differences in the profiles of the components of the displacement vectors of the elastic wave. Systems with the most different values of acoustic impedances of layers and plates materials have maximum values of S when metallized with thick layers, and also have maximum differences in the profiles of the components of the displacement vectors of the elastic wave. PACS: 43.25.Fe; 43.35.Cg; 77.65.-j

Ultra-Large-Coupling and Spurious-Free SH0 Plate Acoustic Wave Resonators Based on Thin LiNbO3.

This study lays a foundation for the design of the SH0 plate acoustic wave (PAW) resonators based on LiNbO3 plate, and are applicable to the ultra-wideband filters and next-generation tunable filters. The coupling coefficient ( k2 ) of SH0 mode is optimized to as high as 55% and wideband spurious are well controlled by analyzing the propagation characteristics of plate modes in LiNbO3. The SH0 mode is demonstrated to be slowly dispersive and features the superiority of interdigital transducer (IDT)-defining frequency over most other plate modes. On the device level, the transducer types and electrode materials are investigated and compared. In addition, for edge-reflected SH0 resonators, stopband dispersion analysis is provided and the longitudinal ripples are suppressed. For edge-reflected SH0 resonators, a novel perfect edge reflector is proposed with elimination of longitudinal spurious ripples.

Excitation and detection of evanescent acoustic waves in piezoelectric plates: Theoretical and 2D FEM modeling

This paper presents the results of the theoretical and 2D FEM modeling excitation and detection of evanescent acoustic waves in piezoelectric plates. By application of 2D ordinary differential equations derived by Auld, we obtained the dispersion curves of A1 and SH1 waves in YX LiNbO3 and YX KNbO3 plates in proximity to a zero group velocity point. The branches corresponding to evanescent acoustic waves are distinguished. A frequency range where real part of evanescent wave velocity is more than imaginary one was found. In this region evanescent mode is characterized by opposite directions of the phase and group velocities, i.e. this is backward wave. The theoretical analysis was verified in commercial 2D FEM software COMSOL 5.3. By modeling a set of interdigital transducers placed on the surface of Y-cut LiNbO3 wafer with various values of the spatial period we found the resonant frequencies corresponding to evanescent A1 mode. Due to proximity of this wave to a zero group velocity point its properties should be extremely sensitive to change of waveguide quality and ambient air. This is open the possibility to use these waves for development of high sensitive sensors and for nondestructive waveguide analysis.

AMPLITUDE ATTENUATION LAWS OF ACOUSTIC EMISSION WAVES IN PLATE STRUCTURES

Although acoustic emission technology has been used in the nondestructive testing of various plate structures, its further application and development remain limited because the laws governing the amplitude attenuation of acoustic emission waves in plate structures remain unclear. This study aimed to reveal the amplitude attenuation laws of acoustic emission waves in plate structures. Thus, in this study, the traditional model of amplitude attenuation, which is in the form of an exponential function, was improved in reference to cylindrical waves, and an amplitude attenuation model in the form of a power function suitable for plate structures was proposed. Moreover, an experimental system for the attenuation of acoustic emission waves in aluminum alloy plates was established to experimentally verify the proposed model. Finally, the amplitude attenuation laws of acoustic emission waves within the full field, near field, and far field of plate structures were discussed. Results show that the amplitude attenuation laws of acoustic emission waves within the full field, near field, and far field of plate structures all conform to the power function model and gradually reduce as propagation distance increases. In addition, the improved amplitude attenuation model better corresponds with the actual amplitude attenuation trend within the near-field range of the acoustic emission source than other forms of amplitude attenuation models. Specifically, the traditional model of amplitude attenuation model agrees with the actual attenuation laws of acoustic emission waves only within the far-field range of the acoustic emission source. The results of this study provide valuable references for the profound analysis of the propagation characteristics of acoustic emission waves in plate structures and will help promote the development and application of acoustic emission technology. Keywords: Acoustic emission waves, Amplitude, Attenuation, Laws, Plate

Development of electrode structure for acoustic delay lines by using inject printing method

The results concerning to study of possibility to produce electrode structure of acoustic delay lines by using inject printing method are presented. The investigation of morphologic and structure characteristics of electrode structure produced has been carried out. The possibility of excitation of plate acoustic waves characterized by high value of electro-mechanical coupling coefficient by such acoustic delay lines has been demonstrated.

A Label Free Disposable Device for Rapid Isolation of Rare Tumor Cells from Blood by Ultrasounds.

The use of blood samples as liquid biopsy is a label-free method for cancer diagnosis that offers benefits over traditional invasive biopsy techniques. Cell sorting by acoustic waves offers a means to separate rare cells from blood samples based on their physical properties in a label-free, contactless and biocompatible manner. Herein, we describe a flow-through separation approach that provides an efficient separation of tumor cells (TCs) from white blood cells (WBCs) in a microfluidic device, “THINUS-Chip” (Thin-Ultrasonic-Separator-Chip), actuated by ultrasounds. We introduce for the first time the concept of plate acoustic waves (PAW) applied to acoustophoresis as a new strategy. It lies in the geometrical chip design: different to other microseparators based on either bulk acoustic waves (BAW) or surface waves (SAW, SSAW and tSAW), it allows the use of polymeric materials without restrictions in the frequency of work. We demonstrate its ability to perform high-throughput isolation of TCs from WBCs, allowing a recovery rate of 84% ± 8% of TCs with a purity higher than 80% and combined viability of 85% at a flow rate of 80 μL/min (4.8 mL/h). The THINUS-Chip performs cell fractionation with low-cost manufacturing processes, opening the door to possible easy printing fabrication.

Influence of electrical boundary conditions on profiles of acoustic field and electric potential of shear-horizontal acoustic waves in potassium niobate plates

The profiles of an acoustic field and electric potential of the forward and backward shear-horizontal (SH) acoustic waves of a higher order propagating in X-Y potassium niobate plate have been theoretically investigated. It has been shown that by changing electrical boundary conditions on a surface of piezoelectric plates, it is possible to change the distributions of an acoustic field and electric potential of the forward and backward acoustic waves. The dependencies of the distribution of a mechanical displacement and electrical potential over the plate thickness for electrically open and electrically shorted plates have been plotted. The influence of a layer with arbitrary conductivity placed on a one or on the both plate surfaces on the profiles under study, phase and group velocities of the forward and backward acoustic waves in X-Y potassium niobate has been also investigated. The obtained results can be useful for development of the method for control of a particle or electrical charge movement inside the piezoelectric plates, as well a sensor for definition of the thin film conductivity.

Super high sensitive plate acoustic wave humidity sensor based on graphene oxide film

The changes of density and elastic modules due to water vapor adsorption are measured for graphene oxide film at room temperature. Dominant mechanism for acoustic wave humidity sensing by the film is shown to be related with variation of its electric conductivity. Basing on the data, super high sensitive humidity sensor employing high-order Lamb wave with large coupling constant, standard lithium niobate plate, and graphene oxide sorbent film is developed. The minimal detectable level of the sensor is as low 0.03% RH, response times are 60/120s, and reproducibility is ±2.5%. The sensor is completely selective towards H2, CO, CH4, NO, O2.

Transportation control of microfluidic particles using mode switching between surface acoustic waves and plate waves

In this study, we report the numerical and experimental results of guided acoustic mode switching between surface and plate acoustic waves (SAWs and PAWs) for manipulating microparticles suspended in a microfluidic channel. Numerical results show switchable acoustic pressure and acoustic radiation force fields for controlling particle motion in the microfluidic channel by acoustic mode switching. Acoustic mode switching can be achieved by designing an acoustic-wave device and by changing the frequencies of the input electrical signal. The working mechanisms of acoustic-mode-switchable manipulation are revealed. On the basis of numerical prediction, the feasibility of a mode-switchable acoustic microfluidic device is experimentally demonstrated, and the actuation of suspended microparticles using SAWs and PAWs is achieved. We note that this study provides access to mode-switching acoustophoresis.