Acicular Ferrite Transformation Research Articles

Evolution of inclusions in Ti-Ce-Mg deoxidized steel and its effect on acicular ferrite transformation in simulated welding HAZ

The characteristics of non-metallic inclusions in Ti-Ce-Mg deoxidized steel and their influence on the microstructure and toughness of welding heat-affected zone (HAZ) were studied. Results showed that Ti-Ce-Mg deoxidation led to a refined inclusion size and an increase in the number of inclusions below 1 μm. The highest acicular ferrite fraction was obtained in the HAZ of Ti-Ce-Mg steel, and the impact toughness was significantly improved. Ti-Ce deoxidation enhanced the stability of Ti-containing oxide, while Mg treatment promoted its fine dispersion. The final formation of composite inclusions of Ti-Ce-Mg oxide with TiN and MnS enhanced the ability to induce acicular ferrite transformation.

Effect of Mo on acicular ferrite transformation and interphase precipitation of Nb–V–N microalloyed steel during a continuous cooling process

Effect of Mo on acicular ferrite transformation and interphase precipitation of Nb–V–N microalloyed steel during a continuous cooling process

Ultrastrong and ductile steel welds achieved by fine interlocking microstructures with film-like retained austenite

The degradation of mechanical properties caused by grain coarsening or the formation of brittle phases during welding reduces the longevity of products. Here, we report advances in the weld quality of ultra-high strength steels by utilizing Nb and Cr instead of Ni. Sole addition of Cr, as an alternative to Ni, has limitations in developing fine weld microstructure, while it is revealed that the coupling effects of Nb and Cr additions make a finer interlocking weld microstructures with a higher fraction of retained austenite due to the decrease in austenite to acicular ferrite and bainite transformation temperature and carbon activity. As a result, an alloying design with Nb and Cr creates ultrastrong and ductile steel welds with enhanced tensile properties, impact toughness, and fatigue strength, at 45% lower material costs and lower environmental impact by removing Ni.

Effects of Mn-Depleted Zone Formation on Acicular Ferrite Transformation in Weld Metals under High Heat Input Welding

In this present work, during high heat input welding of the weld metal, different types of Mn-depleted zones were achieved by different cooling rates. The effects of cooling rates on Mn-depleted zone formation and acicular ferrite (AF) transformation were analyzed. The Mn-depleted zone around the inclusions, as well as the interface concentration of Mn atoms, are found to be significantly different with different cooling rates. When the cooling rate is 10 °C/s, the interface concentration of Mn atoms around the inclusions is the lowest, the area of Mn-depleted zone is the smallest, and the proportion of AF in the weld metal is the highest. As the cooling rate decreases further, the interface concentration of Mn begins to rise, the area of the Mn-depleted zone gradually expands, and the proportion of AF decreases. However, when the cooling rate reaches 100 °C/s, only a very small amount of MnS precipitates, no Mn-depleted zone forms around the inclusions, and acicular ferrite cannot be produced effectively in the weld metal.

Extremely high temperature carbide precipitation induced intragranular acicular ferrite transformation of M2 steel during semi-solid cooling

Intragranular acicular ferrite (IAF) transformation of M2 steel occurred at extremely high temperature (1180 ∼ 960 °C) during semi-solid cooling. The uncommon IAF transformation was observed in situ via confocal laser scanning microscope. Small VC carbide particles precipitated explosively during semi-solid cooling and they acted as the preferential site for the nucleation of IAF due to the low lattice misfit with ferrite. The length of ferrite lath showed a bimodal behavior that long primary ferrite laths and short secondary ferrite laths both existed. The acicular laths intersected with each other and terminated at the solid boundary or interface. The prior solid austenite grain was filled with acicular ferrite. The IAF might help refine the effective grain size and improve the strength of semi-solid M2 steel.

A Comparative Study of Acicular Ferrite Transformation Behavior between Surface and Interior in a Low C–Mn Steel by HT-LSCM

In this study, the acicular ferrite transformation behavior of a Ti–Ca deoxidized low carbon steel was studied using a high-temperature laser scanning confocal microscopy (HT-LSCM). The in situ observation of the transformation behavior on the sample surface with different cooling rates was achieved by HT-LSCM. The microstructure between the surface and interior of the HT-LSCM sample was compared. The results showed that Ti–Ca oxide particles were effective sites for acicular ferrite (AF) nucleation. The start transformation temperature at grain boundaries and intragranular particles decreased with an increase in cooling rate, but the AF nucleation rate increased and the surface microstructure was more interlocked. The sample surface microstructure obtained at 3 °C/s was dominated by ferrite side plates, while the ferrite nucleating sites transferred from grain boundaries to intragranular particles when the cooling rate was 15 °C/s. Moreover, it was interesting that the microstructure and microhardness of the sample surface and interior were different. The AF dominating microstructure, obtained in the sample interior, was much finer than the sample surface, and the microhardness of the sample surface was much lower than the sample interior. The combined factors led to a coarse size of AF on the sample surface. AF formed at a higher temperature resulted in the coarse size. The available particles for AF nucleation on the sample surface were quite limited, such that hard impingement between AF plates was much weaker than that in the sample interior. In addition, the transformation stress in austenite on the sample surface could be largely released, which contributed to a coarser AF plate size. The coarse grain size, low dislocation concentration and low carbon content led to lower hardness on the sample surface.

Transformation stasis phenomenon and overall transformation kinetics of low-carbon, Nb-bearing ferrous alloy

To illuminate the overall transformation kinetics of low-carbon, Nb-bearing ferrous Alloy (Nb ferrous alloy), a novel method was proposed to investigate the overall transformation behavior on the basis of bainitic transformation stasis theory. The stability and transformation behavior of austenite were controlled by choosing different isothermal temperatures nearby or away from the transformation start temperature (Ts), and the dilatometric variation discipline and microstructural features corresponding to different processes were investigated. Nucleation mechanisms throughout the overall transformation process were further discussed on the basis of the classical J-M-A model. Results indicate the overall transformation kinetics concerning to studied Nb ferrous alloy can be nearly separated into two stages in terms of the dilatometric variation discipline together with microstructural features, they are (a) Acicular ferrite (AF) transformation stage with relative high transformation rate at initial transformation stage, and (b) Conventional bainite (CB) transformation stage with low transformation rate in the late stage. The possible nucleation is the diffusion-controlled mechanism with regard to studied Nb ferrous alloy during isothermal temperature from 580 ℃ to 440 ℃. At the initial stage, AF nucleates on the parent austenite grain boundary or sub-grain boundary and grows in the mode of arbitrary dimensional, and the nucleation rate is decreased gradually. At the second stage, the formed AF impingements each other, and new phase nucleus attached to parent austenite grain boundary, sub-grain boundary or AF boundary begin to grow in the mode of incrassation and transform into CB, and the nucleation rate is almost zero throughout the secondary transformation stage.

A novel process involving multiple strengthening mechanisms for production of low-residual stress X80 pipe steel based on ultra-fast cooling

Abstract This work aims at developing low-residual stress heavy gauge X80 pipe steel. A novel processing route involving combined mechanisms of precipitation strengthening and refining grain was first proposed based on ultra-fast cooling. Compared with conventional laminar cooling process, the high cooling rate of ultra-fast cooling and the induced re-reddening could promote the acicular ferrite transformation and nano precipitations, which ensured the toughness and strength at the same time. With ultra-fast cooling, the X80 pipe steel could be prepared at high coiling temperature instead of low coiling temperature less than 400 °C and the X80 pipe steel exhibited low-residual stress. Besides, this work also indicated a wide processing widow under ultra-fast cooling.

Effect of austenite grain size on acicular ferrite transformation in a HSLA steel

Austenite grain size is well known to have a significant influence on various phase transformations in steels. Although the effects of many thermomechanical processing parameters on acicular ferrite (AF) transformation in HSLA steels have been investigated, little attention has been paid to the influence of austenite grain size. Therefore, in this research, different parameters of solid-solution heat treatment and rough deformation were adopted to generate austenite with different grain sizes and the effects of austenite grain size before deformation on the AF transformation and grain refinement were investigated. It was found that the reduction of prior-austenite grain size (PAGS) from 62.8 μm to 37.0 μm before austenite deformation promotes the AF transformation and simultaneously refines and homogenises the transformed microstructures. A reciprocally increased density of deformation induced dislocations with the reduction of PAGS was proposed to account for these results, which not only increase the nucleation sites of AF but also suppress the lengthening of BF laths. Further reducing PAGS from 37.0 μm to 22.3 μm, the fraction of AF is not increased and the transformed microstructure is not refined. Possible differences in the type, distribution, and density of austenite deformation substructures between austenite with PAGSs of 37.0 μm and 22.3 μm were argued to be responsible for the cease of grain refinement. The relationship between effective grain sizes and the Sv parameter was investigated and an equation relating effective grain sizes with processing parameters was also proposed.

Microstructural Evolution and the Precipitation Behavior in X90 Linepipe Steel During Isothermal Processing

Thermomechanical controlled processing of 560-MPa (X90) linepipe steel was simulated in the laboratory using a thermomechanical simulator to study the microstructural evolution and precipitation behavior during isothermal holding. The results indicated that martensite was obtained when the steels were isothermally held for 5 s at 700 °C. Subsequently, granular bainite and acicular ferrite transformation occurred with increased holding time. Different amount of polygonal ferrite formed after isothermally holding for 600-3600 s. Pearlite nucleated after isothermally holding for 3600 s. Precipitation occurred after isothermal holding for 5 s and continuous precipitation occurred at grain boundaries after isothermally holding for 600 s. After isothermally holding for 3600 s, large Nb/Ti carbide precipitated. The presence of MX-type precipitates was confirmed by diffraction pattern. The interphase precipitation (IP) occurred between 5 and 30 s. Maximum hardness was obtained after isothermally holding for 600 s when IP occurred and rapidly decreased to a low value, mainly because polygonal ferrite dominated the microstructure after isothermally holding for 3600 s.

Formation mechanism and control methods of acicular ferrite in HSLA steels: A review

High strength low alloy (HSLA) steels have been widely used in pipelines, power plant components, civil structures and so on, due to their outstanding mechanical properties as high strength and toughness, and excellent weldability. Multi-phase microstructures containing acicular ferrite or acicular ferrite dominated phase have been proved to possess good comprehensive properties in HSLA steels. This paper mainly focuses on the formation mechanisms and control methods of acicular ferrite in HSLA steels. Effect of austenitizing conditions, continuous cooling rate, and isothermal quenching time and temperature on acicular ferrite transformation was reviewed. Furthermore, the modified process to control the formation of multi-phase microstructures containing acicular ferrite, as intercritical heat treatments, step quenching treatments and thermo-mechanical controlled processing, was summarized. The favorable combination of mechanical properties can be achieved by these modified treatments.

Conditions for the occurrence of acicular ferrite transformation in HSLA steels

For the class of steels collectively known as high strength low alloy (HSLA), an acicular ferrite (AF) microstructure produces an excellent combination of strength and toughness. The conditions for the occurrence of the AF transformation are, however, still unclear, especially the effects of austenite deformation and continuous cooling. In this research, a commercial HSLA steel was used and subjected to deformation via plane strain compression with strains ranging from 0 to 0.5 and continuous cooling at rates between 5 and 50 °C s−1. Based on the results obtained from optical microscopy, scanning electron microscopy and electron backscattering diffraction mapping, the introduction of intragranular nucleation sites and the suppression of bainitic ferrite (BF) laths lengthening were identified as the two key requirements for the occurrence of AF transformation. Austenite deformation is critical to meet these two conditions as it introduces a high density of dislocations that act as intragranular nucleation sites and deformation substructures, which suppress the lengthening of BF laths through the mechanism of mechanical stabilisation of austenite. However, the suppression effect of austenite deformation is only observed under relatively slow cooling rates or high transformation temperatures, i.e., conditions where the driving force for advancing the transformation interface is not sufficient to overcome the austenite deformation substructures.

Effect of heat input and M-A constituent on microstructure evolution and mechanical properties of heat affected zone in low carbon steel

Microstructure evolution and impact toughness of simulated heat affected zone (HAZ) in low carbon steel have been investigated in this study. Thermal simulator was used to simulate microstructure evolution in HAZ with heat input of 10 – 100 kJ / cm welding thermal cycle. Results indicated that microstructure of HAZ mainly consisted of acicular ferrite (AF) inside grain and high volume fraction of grain boundaries ferrite (GBF) at prior austenite boundaries; the size of GBF and effective grain size increased with increasing heat input. Excellent impact toughness (more than 150 J at −40 °C) was obtained in HAZ with heat input less than 50 kJ / cm. When heat input was 100 kJ / cm, the impact toughness of HAZ decreased to 18 J because of the presence of large M-A constituent with lath-form in HAZ, assisting the micro-crack initiation and decreasing the crack initiation energy seriously. Effect of inclusions on acicular ferrite transformation in HAZ was also discussed.

Effect of Dissolution and Precipitation of Nb on Phase Transformation, Microstructure, and Microhardness of Two High-Nb Pipeline Steels

Niobium (Nb) as an important microalloying element is widely applied in high strength pipeline steels. In this work, the continuous cooling transformation diagrams of two high-Nb steels with and without hot deformation were studied using a Gleeble 3500 thermal simulator. The amounts of dissolved Nb, undissolved Nb, and precipitated Nb were determined by inductively coupled plasma-atomic emission spectrometry. Results show that the increasing of Nb content in the high-Nb steels can restrain the prior austenite grain growth, dynamic, and/or static recrystallization; moreover, it can suppress polygonal ferrite transformation and promote acicular ferrite and bainite transformation, refining the microstructure and increasing the microhardness as a consequence. Nevertheless, the amplified Nb content in steels escalates trends of strain-induced Nb(C,N) precipitation. The increase in the amount of Nb(C,N) precipitates promote the polygonal ferrite and acicular ferrite transformation, while also decrease the microhardness. The results from this work show that the higher Nb content of 0.13% in the tested steel is unnecessary.

In situ observation of austenite grain growth and transformation temperature in coarse grain heat affected zone of Ce-alloyed weld metal

Laser scanning confocal microscopy (LSCM) was used to study the inhibition of austenite grain growth by the inclusions and the effect of cerium on the trend of acicular ferrite (AF) and ferrite side plate (FSP) transformation temperature in coarse grain heat affected zone (CGHAZ) of Ce-alloyed weld metals. The results showed there were lots of tiny cerium oxides and sulfides inclusions in the CGHAZ of Ce-alloyed weld metals. When the concentration of Ce was 0.021%, the volume fraction of inclusions in weld metal CGHAZ was higher and the inclusion size was smaller, therefore austenite grain size was smaller with the increase of high-temperature residence time. Cerium tended to segregate at austenite grain boundaries, so FSP transformation temperature decreased and FSP transformation was suppressed. On the contrary, AF transformation temperature increased because AF transformation was promoted in CGHAZ of the Ce-alloyed weld metal, especially when the concentration of Ce was 0.021%.

Role of Lanthanum Addition on Acicular Ferrite Transformation in C–Mn Steel

Acicular ferrite formation in C–Mn steel after rare earth La addition and the potency of different La-containing inclusions inducing the formation of acicular ferrite have been investigated. It was found that there would be a large amount of acicular ferrite in quenched steel after 0.020 mass% La additions. The size of effective inclusion for acicular ferrite nucleation is mainly 1–4 µm. The best single La-containing effective inclusion is La2O2S. When MnS attached to the surface of La2O2S forming complex inclusion, the potency of inclusion on nucleating acicular ferrite is enhanced significantly. Low lattice mismatch between α–Fe and La2O2S plays an important role on acicular ferrite nucleation. When patches of MnS precipitated on the surface La2O2S forming the complex inclusion, the main mechanism for that inclusion is the combine of low degree of lattice mismatch and existing of Mn-depleted zone.

Acicular ferrite formation during isothermal holding in HSLA steel

Microstructural observation and high-resolution dilatometry were employed to investigate acicular ferrite formation during isothermal holding in the HSLA steel. A decrease in isothermal temperature suppresses formation of polygonal ferrite and promotes formation of acicular ferrite. Island-like martensite/austenite constituents are dispersed inside of the acicular ferrite grain. The displacive model assuming autocatalytic nucleation was developed to describe the incomplete transformation phenomenon well. Decrease of isothermal temperature lowers the activation energy, and thus enhances the formation of acicular ferrite. Increase of amount of polygonal ferrite and acicular ferrite both results in decrease of M s. Formation of polygonal ferrite causes diffusion of solute alloying atoms into the untransformed austenite, which lowers M s. Acicular ferrite transformation suppresses martensitic transformation by diffusion of solution atoms during isothermal holding, and introduction of internal stress resulting from volume expansion during FCC → BCC transformation.

Phase transformation mechanism of low-carbon high strength low alloy steel upon continuous cooling

The transformation characteristics of low-carbon high strength low alloy steel for various cooling rates were systematically investigated by means of dilatometric measurements and microstructure observations. According to the results, it is recognised that the increase of the cooling rate could lead to microstructure evolution from a mixture of polygonal ferrite, acicular ferrite and bainite ferrite to the dual phase of acicular ferrite and bainite ferrite. The kinetics mechanism of the phase transformation was further studied by a modified analytical phase transformation model, which involves site saturation, diffusion/interface-controlled growth, impingement correction for randomly distributed growing particles. It is demonstrated that diffusion-controlled polygonal ferrite and acicular ferrite phase transformation precedes the interface-controlled bainite ferrite phase transformation. For the diffusion-controlled growth, the transformation is slowed down with the increase of the cooling rate, which prevents the diffusion process to some degree and increases the diffusion activation energy QD. For the interface-controlled growth, the interface migration activation energy shows a declining trend with the increase of cooling rate, thus promoting the transformation.

Microstructure Control of Non-quenched and Tempered CT80 Grade Coiled Tubing Steel

Complex working condition of coiled tube (CT) steel demands high strength and low ratio of yield strength (YS) to tensile strength (TS). Reasonable microstructure control is a key problem of CT steel. Controlled rolling and controlled cooling experiments were carried out by two kinds of tested steels with different chemical compositions to develop the non-quenched and tempered CT80 steel. Mechanical properties of the tested steels at different processes are all in good agreement with the properties requirement of CT80. Increasing of Mo and Nb contents improves transformation of acicular ferrite and martensite–austenite (M–A) islands. 4 vol% of fine M/A islands increase TS and decreases ratio of YS/TS. Cooling rate increasing also improves acicular ferrite transformation and enhances TS, but has little effect on ratio of YS/TS. To meet the requirement of high strength and low ratio of YS/TS, optimized complex microstructure of the CT80 steel is composed of acicular ferrite, about 30 vol% of bainite and 4 vol% of M–A islands.

Continuous Cooling Transformation Behavior of X70 Pipeline Steel

The continuous cooling transformation behaviors were researched on X70 pipeline steel through two pass deformation and non-deformed austenite using Gleeble-3500 thermal mechanical simulator, and static continuous cooling transformation curve and dynamic continuous cooling transformation curve were measured through thermal dilation method and metallographic method. The influence of cooling rate and deformation parameters on microstructure was analyzed. The results show that the hot deformation accelerates the acicular ferrite and polygonal ferrite phase transformation, increases the starting transformation temperature and the finishing transformation temperature significantly, and shifts the CCT curve moving upward to the left side corner. Acicular ferrite is obtained in practice using accelerated cooling rate after deformation Acicular ferrite can be obtained in wider range of cooling rates, and microstructure and island structure is finer through hot deformation.