AC Component Research Articles

Coil-Only High-Frequency Lamb Wave Generation in Nickel Sheets

This study presents a novel, coil-only magnetostrictive ultrasonic detection method that operates effectively without permanent magnets, introducing a simpler alternative to conventional designs. The system configuration is streamlined, consisting of a single meander coil, an excitation source, and a nickel sheet, with both the bias magnetic field and ultrasonic excitation achieved by a composite excitation containing both DC and AC components. This design offers significant advantages, enabling high-frequency Lamb wave generation in nickel sheets for ultrasonic detection while reducing device complexity. Experimental validation demonstrated that an S0-mode Lamb wave at a frequency of 2.625 MHz could be effectively excited in a 0.2 mm nickel sheet using a double-layer meander coil. The experimentally measured wave velocity was 4.9946 m/s, with a deviation of only 0.4985% from the theoretical value, confirming the accuracy of the method. Additionally, this work provides a theoretical basis for future development of flexible MEMS-based magnetostrictive ultrasonic transducers, expanding the potential for miniaturized magnetostrictive patch transducers.

Real-time measurement of electron temperature using a coupled centre-tapped emissive probe and a Langmuir probe (CCTELP)

Abstract Conventional electrostatic probes are commonly used for measuring the plasma parameters like plasma density, electron temperature, plasma potential and floating potential respectively in a laboratory plasma to unveil physical processes of relevance to magnetosphere and fusion plasmas. With such probes, real-time measurement of electron temperature and its fluctuating AC component becomes very difficult. These measurements are significant as they directly give the measure of energy flux and hence can be utilized in estimating the turbulence-induced energy loss in any plasma system, especially useful for electron temperature gradient plasmas. Although Triple Langmuir Probe (TLP) diagnostics provide information on real-time measurement of electron temperature, this involves many complications. These complications of TLP are suitably overcome by the proposed diagnostic, which makes use of a combination of a closely separated centre tap emissive probe (CTEP) and Langmuir probe (LP) installed on a single probe head. The coupled centre-tapped emissive and Langmuir probe (CCTELP) provides direct measurement of electron temperature (T_e) and its fluctuations (T ̃_e). The design of the proposed diagnostic is very simple and it is almost free of rigorous control electronics and post-data analysis otherwise needed to estimate the electron temperature. These features make this diagnostic an additional and simple candidate for real-time measurement of electron temperature and its fluctuation. The paper will highlight details on this novel diagnostics, called CCTELP for the measurement in Maxwellian plasmas.

An advanced meta metrics-based approach to assess an appropriate optimization method for Wind/PV/Battery based hybrid AC-DC microgrid

This paper discusses the growing influence of renewable energy and distributed generation, emphasizing the need for smart control systems to maximize benefits and optimize network performance. However, the absence of a standardized evaluation framework makes it challenging to compare different control systems effectively, especially in large-scale hybrid networks with both AC and DC components. While hybrid energy systems show promise for greener and more reliable power networks, they introduce complexity to control methods. Researchers are exploring innovative approaches, including linear and nonlinear techniques, to leverage renewable energy sources effectively in hybrid grids. The paper provides an overview of heuristic evolutionary optimization methods for microgrids (AC, DC, and hybrid AC-DC), highlighting promising techniques such as Crow Search Algorithm, Modified Crow Search Algorithm, Particle Swarm Optimization, and Genetic Algorithms. Comparative analysis suggests that the Modified Crow Search Algorithm performs best across various evaluation criteria, indicating its potential for optimizing microgrids effectively.

Astragali Radix-Curcumae Rhizoma herb pair reduces the stemness of colorectal cancer cells through HIF-2α/β-catenin pathway

BackgroundColorectal cancer (CRC) is one of the most common causes of cancer-related mortality and significantly impairs quality of life. Astragali Radix-Curcumae Rhizoma (AC) is widely employed in the treatment of CRC in Chinese medicine, but the precise mechanisms remain unclear. PurposeThis study aimed to elucidate the mechanisms by which AC inhibits CRC progression. MethodsThe active components of AC were identified using UPLC-MS/MS analysis. An orthotopic transplantation colorectal tumor model was established in BALB/c mice using the CT26-Lucifer cell line to evaluate the effects of AC. Tumor volumes were monitored using IVIS imaging technology. Histological examination of tumor morphology was performed with hematoxylin and eosin (H&E) staining. Transcriptomic sequencing of mouse tumor samples was conducted to identify critical pathways and molecular targets. The impact of AC on cell viability and migration was assessed using CCK-8 and wound healing assays, respectively. To investigate the effects of AC on CRC cells, an in vitro hypoxic model was established using cobalt chloride (CoCl2), a hypoxia inducer. HIF-2α overexpression was achieved by constructing stable lentiviral vectors. Key targets identified from RNA-seq, such as c-Myc, Ki-67, β-catenin, cleaved caspase 3, CD133, and CD44, were evaluated using western blotting, qRT-PCR, and immunofluorescence assays. Epithelial-Mesenchymal Transition (EMT) and spheroid cloning assays were employed to evaluate phenotypic changes in cancer stem cells. ResultsTwelve components of AC were identified. AC effectively inhibited CRC progression in vivo. Transcriptomic analysis highlighted hypoxic signaling as a significantly enriched pathway, implicating its role in suppressing CRC progression by AC. In the hypoxic model, AC inhibited the proliferation and migration of CRC cells in vitro. Furthermore, AC reduced cancer stemness by downregulating stemness markers, inhibiting EMT, and decreasing tumor sphere formation. The downregulation of hypoxic responses and the shift in stemness by AC involved attenuation of HIF-2α and WNT/β-catenin signaling. ConclusionThis study provides the first evidence that AC reduces the stemness of CRC and the inhibition of the transition of CRC to stem-like cells by AC is closely related to the downregulation of the HIF-2α/β-catenin pathway, especially under hypoxic conditions.

AC Loss Estimation Method for REBCO Superconducting Tapes in AC+DC Fields for Field Windings in Fully Superconducting Synchronous Machine for Electric Aircraft

Abstract The estimation of AC loss in REBa2Cu3O y (REBCO; RE = rare earth, such as Y, Eu, and Gd) superconducting tapes within superconducting synchronous motors and generators for electric aircraft is imperative during the design stage phase to optimize efficiency and cooling considerations. Our previous studies clarified the AC loss characteristics, focusing on estimating the AC loss in armature windings. While the magnetic field applied to the armature windings is exclusively as an AC field, the field windings are subject to a composite field comprising both AC and DC components. Notably, the amplitude of the AC component is markedly smaller than the magnitude of DC component. This study experimentally investigated to consider the AC loss properties in field windings. The experimental results were as follows: When subjected to operational conditions of field windings within synchronous motor and generator, the AC loss increased with the DC field strength. This property is attributed to a reduction in the critical current induced by the external field. Hence, we modified the method for estimating AC loss. Subsequently, we validated the effectiveness of the modified method.

Optimizing Maintenance and Repair of Central Air Conditioning on MV. Tanto Bersinar

For a ship to move smoothly from one port to another, it must be supported by various types of appropriate machinery. One of them is Central AC which functions to maintain the environmental temperature around the ship at an ideal temperature so that the crew remains comfortable in their daily activities while working and resting. Therefore, a ship needs to have a cooling machine to support the comfort of the entire crew. As well as the importance of carrying out regular maintenance and repairs on the cooling machines on board the ship. This research uses a qualitative research approach, data collection techniques using direct observation, interviews and documentation or library studies. The data is processed using triangulation, the data obtained tends to be qualitative data, the data analysis is inductive or qualitative, and the results of qualitative research are to understand meaning, understand uniqueness, construct phenomena and find hypotheses. The results of this research are: 1) Factors that cause damage to Central AC so that it cannot be used properly are due to Central AC components such as dirty condensers, disconnected electrical cables, and dirty dryers as well as other factors, namely lack of accuracy in carrying out maintenance and maintenance. Central AC repair; 2) The impact that occurs when the Central AC does not work properly is a decrease in the performance of the ship's crew due to the discomfort of high room temperatures; and 3) The way to overcome problems when repairing the Central AC on a ship is that the ship's crew is on time to check, clean, maintain and repair the Central AC regularly and correctly.

Modulated step-heating thermography for coating thickness measurement

In this paper, the modulated step-heating thermography is proposed for opaque coating thickness measurement. The surface is heated by a modulated heating flux at a frequency that the thermal wave is confined within the coating layer. The DC component of the thermal signal is normalized by the amplitude of the AC component to cancel out the influences from the variations in heating intensity, surface absorptivity and emissivity, resulting in a linear correlation to the coating thickness. Meanwhile, it eliminates the need for tedious frequency trail and the issue of the nonmonotonicity as suffered in conventional thermography. Both theoretical and experimental results confirmed the effectiveness. Specimens with thickness ranging from 100 to 400 μm are measured with a relative error within ±7.9 %.

Finger photopletysmography detects early acute blood loss in compensated blood donors: a pilot study

Objective. Diagnosis of incipient acute hypovolemia is challenging as vital signs are typically normal and patients remain asymptomatic at early stages. The early identification of this entity would affect patients’ outcome if physicians were able to treat it precociously. Thus, the development of a noninvasive, continuous bedside monitoring tool to detect occult hypovolemia before patients become hemodynamically unstable is clinically relevant. We hypothesize that pulse oximeter’s alternant (AC) and continuous (DC) components of the infrared light are sensitive to acute and small changes in patient’s volemia. We aimed to test this hypothesis in a cohort of healthy blood donors as a model of slight hypovolemia. Approach. We planned to prospectively study blood donor volunteers removing 450 ml of blood in supine position. Noninvasive arterial blood pressure, heart rate, and finger pulse oximetry were recorded. Data was analyzed before donation, after donation and during blood auto-transfusion generated by the passive leg-rising (PLR) maneuver. Main results. Sixty-six volunteers (44% women) accomplished the protocol successfully. No clinical symptoms of hypovolemia, arterial hypotension (systolic pressure < 90 mmHg), brady-tachycardia (heart rate <60 and >100 beats-per-minute) or hypoxemia (SpO2 < 90%) were observed during donation. The AC signal before donation (median 0.21 and interquartile range 0.17 a.u.) increased after donation [0.26(0.19) a.u; p < 0.001]. The DC signal before donation [94.05(3.63) a.u] increased after blood extraction [94.65(3.49) a.u; p < 0.001]. When the legs’ blood was auto-transfused during the PLR, the AC [0.21(0.13) a.u.; p = 0.54] and the DC [94.25(3.94) a.u.; p = 0.19] returned to pre-donation levels. Significance. The AC and DC components of finger pulse oximetry changed during blood donation in asymptomatic volunteers. The continuous monitoring of these signals could be helpful in detecting occult acute hypovolemia. New pulse oximeters should be developed combining the AC/DC signals with a functional hemodynamic monitoring of fluid responsiveness to define which patient needs fluid administration.

Small-signal modeling comparison of dual active bridge converter

The dual active bridge (DAB) converter is a versatile DC-DC converter, which has AC components in the high-frequency transformer within the converter topology as well as DC components at the input and output sides. These AC components are constructed from infinite sinusoids of multiples of the converter's switching frequency. Different approaches have been proposed to model the DAB converter. The generalized averaging modeling (GAM) includes only the first order harmonic of the inductor current with the DC components of the input and output voltages and currents. For better model accuracy, harmonic-domain models have been employed, where the model includes all the harmonics of all the model state variables up to an arbitrary harmonic index. While the harmonic model provides a systematic approach to include the harmonics, this increases the model complexity. To avoid this complexity, the flexible harmonic model is used where harmonics can be selected per each state variable without needing to be in successive order. The aforementioned modeling approaches have been implemented on the DAB converter. This paper aims to compare between the dynamic performance of GAM and the harmonic modeling approaches under different disturbances, where the GAM approach provided a simple model with acceptable results that can be used for controller design, while the LTP model provided a more complex model with better accuracy that is suitable for harmonic studies. The models have been validated and compared using simulations executed on MATLAB /Simulink environment.

Evaluating Vascular Depth-Dependent Changes in Multi-Wavelength PPG Signals Due to Contact Force.

Photoplethysmography (PPG) is a non-invasive method used for cardiovascular monitoring, with multi-wavelength PPG (MW-PPG) enhancing its efficacy by using multiple wavelengths for improved assessment. This study explores how contact force (CF) variations impact MW-PPG signals. Data from 11 healthy subjects are analyzed to investigate the still understudied specific effects of CF on PPG signals. The obtained dataset includes simultaneous recording of five PPG wavelengths (470, 525, 590, 631, and 940 nm), CF, skin temperature, and the tonometric measurement derived from CF. The evolution of raw signals and the PPG DC and AC components are analyzed in relation to the increasing and decreasing faces of the CF. Findings reveal individual variability in signal responses related to skin and vasculature properties and demonstrate hysteresis and wavelength-dependent responses to CF changes. Notably, all wavelengths except 631 nm showed that the DC component of PPG signals correlates with CF trends, suggesting the potential use of this component as an indirect CF indicator. However, further validation is needed for practical application. The study underscores the importance of biomechanical properties at the measurement site and inter-individual variability and proposes the arterial pressure wave as a key factor in PPG signal formation.

Optimal Power Flow in Hybrid AC/DC Microgrid using ANN for Cost Minimization

Currently, this work lays the ground work for sophisticated control methods and decision support systems in hybrid microgrid operations by providing insightful information about integrating artificial intelligence for improved microgrid control. In this work, a neural network (NN) method is proposed for power flow analysis in an IEEE 12-bus-based Hybrid AC/DC Microgrid. The study optimizes power dispatch, minimizes expenses, and minimizes losses in both AC and DC components. Simulation is carried using MATLAB software and the results are presented and analysed. The accuracy of the NN’s predictions of active power flows is demonstrated by training it on historical data and validating it on real-time observations. Regression plots comparing anticipated and real values demonstrate the effectiveness of NN-based analysis in reaching the ideal power distribution.

A Novel Current Measurement Offset Error Compensation Method Based on the Adaptive Extended State Observer for IPMSM Drives

Offset error from the measured phase current mostly causes a performance afflicted for interior permanent-magnet synchronous motor (IPMSM) drives, and innovative solutions are eagerly sought. Considering this, this paper proposes an adaptive extended state observer (AESO) to compensate the current measurement offset error (CMOE) without additional hardware. In the proposed scheme, the AESO is designed in a stationary coordinate system to estimate CMOE in DC form. Notably, the proposed AESO possesses a second-order low-pass filtering characteristics. With this, the proposed method shows a high robustness against the disturbances from the AC components caused by motor parameter changes, etc. Furthermore, the adaptive gains enable the proposed scheme to maintain a satisfactory performance under the motor frequency changes. The feasibility of the proposed scheme is thoroughly verified by extensive experimental tests based on the test bench of a 3-kW IPMSM drives.

Spatial frequency domain imaging combining profile correction enables accurate real-time quantitative mapping of optical properties of apples

Spatial frequency domain imaging technology enables non-contact, wide-field quantitative analysis of optical properties in strong turbid media, thereby enhancing bruise detection in fruits based on changes in optical property values. However, precise and real-time measurement of the optical properties of curved biological materials is challenging due to the significant influence of tissue contours. This paper primarily presents a research study on real-time correction method based on the property that DC component diffuse reflectance (Rd_DC) and AC component diffuse reflectance (Rd_AC) are influenced by the contour trend of the tissue in a similar manner. The aim of this method is to eliminate the significant impact of sample contour angle on demodulation and enhance the detection of apple bruise. Sinusoidal illumination at a spatial frequency of 0.2 mm−1 was projected at 730 nm, with the experiments carried out on standard reflector, polytetrafluoroethylene sphere, and non-bruised and bruised apples. The results showed that, the relative error of the planar standard reflector decreased from the maximum value of 52.85–4.74%. The median of the Rd_AC for the polytetrafluoroethylene spherical standard, which fluctuated between 0.6 and 0.8, was corrected to the theoretical value of 1. For normal apples, the maximum fluctuation in the standard deviation of Rd_AC, after median filtering, reduced from 172.94% at 300×300 pixels to 18.69%. The boxplot of Rd_AC for bruised apples became smaller, with the lower fence being corrected from nearly 0–0.1750, which closely matched the theoretical value of 0.17. Additionally, the correlation of reduced scattering coefficient (μs′) in the ideal region of interest (100×100 pixels) remained at 0.9785 before and after correction, while other areas were corrected, making the bruising more pronounced. The correction method did not require additional experiments, with the consumed time in millisecond level.

A Novel Method for Removal of Dual Decaying DC Offsets to Enhance Discrete Fourier Transform-Based Phasor Estimation

This paper presents a novel method for the removal of dual decaying DC offsets (DDCOs) to enhance discrete Fourier transform-based phasor estimation. The method proposed in this paper uses the sum of even samples and the sum of odd samples from the input signal to remove the AC components, thereby precisely estimating the primary and secondary DDCOs. The fluctuations induced by DCCOs present in the output of traditional DFT methods are eliminated by using the estimated DCCOs. The performance of the method was evaluated in terms of both mathematical-generated signals and fault current signals from a 154 kV Korean overhead transmission system. PSCAD/EMTDC was used to generate fault current signals at various fault distances and angles. The results show that the proposed method can estimate the phasor of the fundamental frequency component accurately regardless of the primary and secondary DCCOs. The paper concludes by describing the hardware implementation in a prototype unit that considers the real-world requirements of power system protection.

Research on Residual-Current Measurement System of Substation Considering Magnetic Shielding Effect.

Residual current is an important monitoring quantity of a power system, and a current sensor plays an important role in detecting current. The substation environment is complex. In addition to the power frequency signal, residual current also has AC and DC components. But it is also affected by the stray magnetic field of the substation. Therefore, the accuracy of the current sensor demands higher requirements. The tunnel magnetoresistive sensor has the advantages of a stable operation, high efficiency, and energy saving, but it is easily affected by the external stray magnetic field during measurements, resulting in a large error. Therefore, this paper proposes a residual-current sensing monitoring system considering the magnetic shielding effect. The root mean square error of the magnetic shielding structure is only 0.572 mA, which can effectively reduce the influence of the external magnetic field and improve the detection accuracy. At the same time, the DC measurement error is less than 1%, the AC measurement error is less than 5%, and the hybrid AC/DC error is less than 8%. It has good response ability and can accurately detect residual current.

Discussions on the Instantaneous Reactive Power Theory Terms in the General Case Based on the Symmetric Components

This paper deals with the presentation of different terms of the powers presented in the Instantaneous Reactive Power Theory (IRPT) in the general case of a generic power system voltage. This presentation is based on the use of the symmetric components in the E. Clarke stationary frame, where the instantaneous real active power, the instantaneous imaginary reactive power and the instantaneous zero sequence power are divided into their DC components and AC components function of the symmetric components. The contributions of these terms in the transfer of the energy from the power supply to the load in four wire system are explained, hence, a good choice of the power to be compensated using shunt active power filter can be obtained. Finally, simulation results are presented under unbalanced and distorted generic power system voltages, where different terms of the instantaneous reactive power theory are clarified and presented based on symmetrical components.

Realism of Tactile Texture Playback: A Combination of Stretch and Vibration.

This study investigates the effects of two stimulation modalities (stretch and vibration) on natural touch sensation on the volar forearm. The skin-textile interaction was implemented by scanning three textures across the left forearm. The resulting skin displacements were recorded by the digital image correlation technique to capture the information imparted by the textures. The texture recordings were used to create three playback modes (stretch, vibration, and both), which were reproduced on the right forearm. Two psychophysical experiments compared the texture scans to rendered texture playbacks. The first experiment used a matching task and found that to maximize perceptual realism, i.e., similarity to a physical reference, subjects preferred the rendered texture to have a playback intensity of 1X - 2X higher on DC components (stretch), and 1X - 3.5X higher on AC components (vibration), varying across textures. The second experiment elicited similarity ratings between the texture scans and playbacks and showed that a combination of stretch and vibration was required to create differentiated texture sensations. However, the intensity amplification and use of two stimuli were still insufficient to create fully realistic texture sensations. We conclude that mechanisms beyond single-site uniaxial stimuli are needed to reproduce realistic textural sensations.

Synergism of Light-Induced [4 + 4] Cycloaddition and Electron Transfer Toward Switchable Photoluminescence and Single-Molecule Magnet Behavior in a Dy4 Cubane.

Molecular materials possessing switchable magneto-optical properties are of great interest due to their potential applications in spintronics and molecular devices. However, switching their photoluminescence (PL) and single-molecule magnet (SMM) behavior via light-induced structural changes still constitutes a formidable challenge. Here, a series of cubane structures were synthesized via self-assembly of 9-anthracene carboxylic acid (HAC) and rare-earth ions. All complexes exhibited obvious photochromic phenomena and complete PL quenching upon Xe lamp irradiation, which were realized via the synergistic effect of photogenerated radicals and [4 + 4] photocycloaddition of the AC components. The quenched PL showed the largest fluorescence intensity change (99.72%) in electron-transfer photochromic materials. A reversible decoloration process was realized via mechanical grinding, which is unexpectedly in the electron-transfer photochromic materials. Importantly, an SMM behavior of the Dy analog was observed after room-temperature irradiation due to the photocycloaddition of AC ligands and the photogenerated stable radicals changed the electrostatic ligand field and magnetic coupling. Moreover, based on the remarkably photochromic and photoluminescent properties of these compounds, 2 demos were applied to support their application in information anti-counterfeiting and inkless printing. This work, for the first time utilizing the simultaneous modulation of photocycloaddition and photogenerated radicals in one system, realizes complete PL quenching and light-induced SMM behavior, providing a dynamical switch for the construction of multifunctional polymorphic materials with optical response and optical storage devices.

New single‐stage bidirectional three‐phase ac‐dc solid‐state transformer

AbstractHigh‐power applications with low‐voltage (LV) dc loads, for example, fast charging stations for electric vehicles (EVs), are typically supplied from the medium‐voltage (MV) grid. Aiming for low volume, MVac‐LVdc solid‐state transformers (SSTs) that provide galvanic separation with medium‐frequency transformers (MFTs) are thus considered, which are conventionally realized as two‐stage systems that consist of an ac‐dc power‐factor‐correction (PFC) rectifier and an isolated dc‐dc converter. This letter extends a new single‐stage isolated bidirectional PFC rectifier concept to MV levels, resulting in an SST that performs MVac‐LVdc conversion in a single converter stage and, unlike many modular SST concepts, employs only a single MFT. The SST's primary side operates modular‐multilevel‐converter (MMC) bridge legs, whose input voltages contain large ac components, in the quasi‐two‐level mode to minimize the cell capacitors. The secondary side employs a standard LV three‐phase rectifier, and a dual‐active‐bridge‐(DAB)‐like modulation strategy allows power flow regulation and ensures sinusoidal grid currents. The concept is explained and validated using detailed circuit simulations of an exemplary 1‐MW system operating between a 10‐kV three‐phase grid and an 800‐V dc output. The component stresses are evaluated, and an efficiency of 98.1% and a power density of up to 0.6 kW/dm3 are estimated.

Mitigating AC and DC Interference in Multi-ToF-Camera Environments.

Multi-camera interference (MCI) is an important challenge faced by continuous-wave time-of-flight (C-ToF) cameras. In the presence of other cameras, a C-ToF camera may receive light from other cameras' sources, resulting in potentially large depth errors. We propose stochastic exposure coding (SEC), a novel approach to mitigate MCI. In SEC, the camera integration time is divided into multiple time slots. Each camera is turned on during a slot with an optimal probability to avoid interference while maintaining high signal-to-noise ratio (SNR). The proposed approach has the following benefits. First, SEC can filter out both the AC and DC components of interfering signals effectively, which simultaneously achieves high SNR and mitigates depth errors. Second, time-slotting in SEC enables 3D imaging without saturation in the high photon flux regime. Third, the energy savings due to camera turning on during only a fraction of integration time can be utilized to amplify the source peak power, which increases the robustness of SEC to ambient light. Lastly, SEC can be implemented without modifying the C-ToF camera's coding functions, and thus, can be used with a wide range of cameras with minimal changes. We demonstrate the performance benefits of SEC with thorough theoretical analysis, simulations and real experiments, across a wide range of imaging scenarios.