Absorption Rate Research Articles

Synchrotron-driven Instabilities in Relativistic Plasmas of Arbitrary Opacity

Recent work has shown that synchrotron emission from relativistic plasmas leads the electron distribution to form an anisotropic ring in momentum space, which can be unstable to both kinetic and hydrodynamic instabilities. Fundamental to these works was the assumption that the plasma was optically thin, allowing all emitted radiation to escape. Here, we examine the behavior of these instabilities as the plasma becomes more optically thick. To do this, we extend a recently developed Fokker–Planck operator for synchrotron emission and absorption in mildly relativistic plasmas to ultrarelativistic plasmas. For a given set of plasma parameters, photons emitted by higher-energy electrons tend to be higher frequency, and thus more easily escape the plasma. As a result, the ratio of the photon emission rate (radiative drag) to absorption rate (radiative diffusion) for a given electron is extremely energy dependent. Given this behavior, we determine the critical parameters that control the opacity, and show how the plasma gradually transitions to become more isotropic and stable at higher opacity.

Dopamine‐modified Highly Dispersed ZIF‐8 to Promote CO2 Absorption

AbstractCO2 capture technology has been widely used to reduce CO2 emissions, resulting in a variety of capture methods and materials. Among them, the more widely used is the chemical absorption method. However, the chemical absorption method has problems such as high energy consumption and slow absorption rate. In order to solve the above problems, we prepared an effective catalyst to improve the CO2 absorption rate. ZIF‐8 and hydrophilic ZIF‐8‐DA were prepared by in situ synthesis under ambient conditions. The catalytic effect of the hydration reaction of ZIF‐8 and ZIF‐8‐DA was tested using CO2 absorption regeneration experiments under aqueous and alkaline conditions, respectively. The results showed that the synthesized catalysts could significantly enhance the CO2 absorption in water and alkaline solution. The addition of 0.1 wt % of ZIF‐8 in alkaline solution increased the average CO2 absorption by 1.80–15.84 %, respectively, while the addition of 0.1 wt % of ZIF‐8‐DA increased the CO2 absorption by 7.01–25.36 %. In addition, both catalysts had excellent reusability and maintained high performance even after five absorption and regeneration cycles. Polymer dispersibility index (PDI) results showed that ZIF‐8‐DA dispersed more uniformly in aqueous solution.

Development of Novel Cardanol-Derived Reactive Dispersing Agents for Bio-Based Anionic-Nonionic Waterborne Polyurethane.

This study successfully developed a bio-based, photocurable, anionic-nonionic dual-functional chain extender, and sulfonated cardanol-based polyethylene glycol (SCP), derived from renewable resources-cardanol and polyethylene glycol-for application in waterborne polyurethane dispersions (WPUDs). Utilizing SCP as a chain extender, WPUDs were prepared through a typical acetone process with poly(butylene adipate) (PBA), isophorone diisocyanate (IPDI), and ethylene diamine (EDA) at a constant NCO/OH ratio of 1:1. This research focused on the effects of polyethylene glycol molecular weight and SCP dosage on the particle size, stability, and film-forming properties of the WPUD. Optimal dispersion stability and film-forming performance were achieved with a polyethylene glycol molecular weight of 1500 and a PBA to SCP molar ratio of 4:1, yielding a particle size of 0.326 ± 0.010 μm and excellent storage stability over six months. The resulting WPU coatings exhibited a tensile strength of 11.4 MPa, which increased to 16.8 MPa after UV irradiation owing to the formation of a semi-interpenetrating network via the photopolymerization of cardanol's unsaturated side chains. UV cross-linking also enhanced water resistance, reducing the water absorption rate (WAR) from 18.68% to 4.21% and the water vapor transmission rate (WVTR) from 6.59 × 10-5 g·m⁻¹·Pa⁻¹·d⁻¹ to 2.26 × 10⁻⁵ g·m⁻¹·Pa⁻¹·d⁻¹, while also improving thermal stability. These findings demonstrate that SCP offers a sustainable and effective solution for developing high-performance WPU coatings.

CO2 plasma inducing steel-slag with active sites for efficient growth of carbon nanotubes for the high-performance microwave absorption

As a solid waste generated in the metallurgical process, the highly efficient catalysis of steel-slag for carbon nanotube (CNT) growth remains a huge challenge. Herein, a CO2 plasma-inducing approach for modifying the steel-slag catalyst with rich active sites was developed for CNT growth in the chemical vapor deposition (CVD) process. Furthermore, the high-energy CO2 plasma refines the particles on the steel-slag surface, reducing the particle size on the surface of steel-slag effectively increasing the active sites of the catalyst. In addition, the thermal effect generated by the gas molecule ionization process under CO2 increases the background temperature of the steel-slag, and the interaction between the oxygen-active substances produced and the iron oxide on the surface of steel-slag undergoes an oxidation reaction upon full contact with high-energy particles, which greatly improves the catalytic efficiency of the steel-slag as a catalyst for CNT, and increases the catalytic efficiency by 50 % compared with the non-plasma modified steel-slag as a catalyst for catalyzing CNTs. In addition, catalytically grown CNTs encapsulate magnetic steel-slag catalysts to form a three-dimensional CNT network structure, with high-performance electromagnetic wave absorption. The composite absorbing material with a thickness of only 3.55 mm has a minimum absorption rate of −64.08 dB for electromagnetic waves at a frequency of 7.9 GHz. The dielectric and the magnetic loss of steel-slag lead to enhanced electromagnetic wave absorption. Therefore, this study provides an inexpensive and environmentally friendly idea for the design of high-efficiency CNT growth and solid waste catalyst modification synthesized with high-performance absorbers.

Study on bioequivalence and influence of obesity-related indicators on pharmacokinetics and pharmacodynamics for insulin degludec in healthy subjects

This study aimed to evaluate the bioequivalence between test and reference insulin degludec (IDeg) and the effects of body composition on pharmacokinetics and pharmacodynamics of IDeg in Chinese healthy volunteers. In this randomized, open-label, crossover trial, 30 healthy Chinese males were assigned to receive a single subcutaneous dose (0.4 IU/kg) of each formulation under 24-h euglycemic hyperinsulinaemic clamp. Body compositions were analysed prior to administration and blood samples were collected at specific times. The 90% of primary pharmacokinetic parameters and 95% of primary pharmacodynamic parameters confidence intervals for the ratio of the least-squares geometric means were all in the range of 80–125%. As the fat content level increases, Cmax, AUC0−12 and GIR-AUC0−24 decreased whereas AUC24−96 increased sequentially. Therefore, the equivalence was demonstrated between test and reference, and in healthy Chinese volunteers, higher levels of adiposity are associated with slower rates of insulin absorption and distribution and the poorer glucose-lowering effect.

Super protective effect, ultra-high juice absorption and long-term antibacterial of Ag-2MI@Chitosan biodegradable sponge for fruit preservation and transportation

Plastic foam packaging is often used for the transportation to avoid mechanical damage to the fruit, but it lacks antibacterial properties, water absorption and is non-degradable, leading to fruit decay and safety risks as well as serious environmental pollution. Herein, Ag-2-Methylimidazole@Chitosan (Ag-2MI@CS) was successfully synthesized by in situ synthesis at normal temperature and pressure, and improved the antibacterial performance of Ag-2MI@CS by using green solvent ethanol to adjust the solvent polarity. The results showed that the long-lasting inhibitory performance of Ag-2MI@CS was significantly improved, the long-lasting antibacterial time has been extended from 24 h to 96 h. Furthermore, Ag-2MI@CS can significantly protect fruits and reduce the damage of fruits, even when falling from a height of 60 cm or under extreme transportation conditions. Besides, Ag-2MI@CS had extremely high absorption rates of water and fruit juice, 1447.69 % and 1356.59 %, respectively, which was conducive to absorbing water generated by respiration and juice generated by damage during transportation, so as to avoid the growth of bacteria caused by water and fruit juice. Ag-2MI@CS can achieve fruit preservation in both indoor static and transportation dynamic conditions. This study offers novel insights into new biodegradable packaging material in fruit transportation.

Effect of kaolin ratio on wear, water absorption, acidic resistance, and mechanical properties of thermoset composites

Natural fiber reinforced composites are easy to decompose in nature compared to synthetic fiber reinforced composites. However, due to environmental effects, natural fibers cannot maintain their properties for a long time. This situation has led researchers to search for natural but non-degradable materials. Kaolin is one of the most abundant minerals in nature and is an easy material to obtain. This study investigated the use of kaolin as a potential natural additive for polymer composites. In this direction, different proportions by weight of kaolin were added to two different polymer matrices (polyester and polyvinylester) materials. Mechanical tests were performed on the samples, and a series of tests were carried out to understand the acid resistance, wear resistance and water absorption properties of the samples. Also, SEM images of the fracture surface, wear surface, and surface exposed to the acidic solutions were taken and examined. According to test results, kaolin improved compression strength while reducing tensile and flexural strength. However, serious improvements have been achieved by nearly 45% and 115% in the tensile modulus and nearly 84% and 218% in the flexural modulus of polyester and polyvinylester composites, respectively. Also, kaolin improved acid resistance and wear properties and reduced the water absorption rate of the composites.

Age-specific optimization of the T2-weighted MRI contrast in infant and toddler brain.

In 0-2-year-old brains, the T2-weighted (T2w) contrast between white matter (WM) and gray matter (GM) is weaker compared with that in adult brains and rapidly changes with age. This study aims to design variable-flip-angle (VFA) trains in 3D fast spin-echo sequence that adapt to the dynamically changing relaxation times to improve the contrast in the T2w images of the developing brains. T1 and T2 relaxation times in 0-2-year-old brains were measured, and several age groups were defined according to the age-dependent pattern of T2 values. Based on the static pseudo-steady-state theory and the extended phase graph algorithm, VFA trains were designed for each age group to maximize WM/GM contrast, constrained by the maximum specific absorption rate and overall signal intensity. The optimized VFA trains were compared with the default one used for adult brains based on the relative contrast between WM and GM. Dice coefficient was used to demonstrate the advantage of contrast-improved images as inputs for automatic tissue segmentation in infant brains. The 0-2-year-old pool was divided into groups of 0-8 months, 8-12 months, and 12-24 months. The optimal VFA trains were tested in each age group in comparison with the default sequence. Quantitative analyses demonstrated improved relative contrasts in infant and toddler brains by 1.5-2.3-fold at different ages. The Dice coefficient for contrast-optimized images was improved compared with default images (p < 0.001). An effective strategy was proposed to improve the 3D T2w contrast in 0-2-year-old brains.

Hyaluronic acid-coated iron oxide nanoparticles for magnetic fluid hyperthermia and methylene blue dye removal: Preparation, physicochemical characterization, and enhancing the heating efficiency

We report here the magnetic fluid hyperthermia properties of water-dispersible hyaluronic acid-coated superparamagnetic iron oxide nanoparticles (HA-MNPs), prepared using the coprecipitation technique followed by ligand exchange. The presence of the hyaluronic acid coating is confirmed using Fourier transform infrared spectroscopy. Magneto-calorimetric studies show good field-induced heating efficiency of the HA-MNPs, where a high specific absorption rate (SAR) of ∼ 315 W/gFe is obtained for ∼ 5 wt% MNP concentration when exposed to an alternating magnetic field amplitude of ∼ 33.1 kA/m at ∼ 126 kHz. The heating efficiency is found to decrease by ∼ 33.8 % after immobilization of the MNPs within an agar matrix, which is attributed to the abrogation of Brownian relaxation. When subjected to an external DC magnetic field, the MNPs form linear chain-like structures, which causes the effective anisotropy energy density to increase. Magneto-calorimetric studies on agar-based oriented samples reveal a ∼ 19.5 % enhancement in SAR, thereby partly compensating for the loss in heating efficiency due to an increase in medium viscosity. The orientational ordering-induced enhancement in SAR is also verified using sweeping rate modified Stoner-Wohlfarth model-based calculations. In vitro cyto-toxicity studies on the HeLa cell lines reveal good cyto-compatibility of the MNPs. The negative charge on the surface of HA-coated MNPs is exploited to remove the cationic methylene blue dye from the aqueous medium, where the dye molecules are found to be physisorbed on the surface of the MNPs. The experimental findings clearly show the high induction heating efficiency, cyto-compatibility, and cationic dye-adsorption efficiency of the prepared HA-MNPs, thereby indicating the suitability of these MNPs for multi-functional applications like magnetic fluid hyperthermia and waste-water purification.

Comparisons of computer simulations and experimental data for capacitive hyperthermia using different split-phantoms

Introduction Several positive clinical trials have demonstrated that capacitive hyperthermia (CHT) improves the effectiveness of radiation therapy for the treatment of various cancer entities. However, the ability of CHT to induce significant heating throughout the body is under debate. Objectives To perform a pilot study involving comparisons of computer simulations and experimental data using different split-phantoms to validate hyperthermia treatment modeling for pre-planning for a clinical CHT system and to investigate the feasibility of split-phantom measurements in capacitive hyperthermia. Materials and methods The CHT system EHY-2030 (Oncotherm, Budapest, Hungary) was used. The system provides two electrode sizes, but only the smaller electrode, indicated as D200 electrode, was investigated in this pilot study. Horizontally and vertically splittable, different multi-slice phantoms with dielectric material properties simulating muscle and electrically low conductive fat were produced and heated. During the heating procedure, temperature-time curves were measured, and thermal images were captured. Specific absorption rate values were derived from the temperature rise (TR) values. Concomitantly, computer field simulations utilizing a detailed CAD-based model of the CHT system were performed using the simulation platform Sim4Life and compared with measurements. Results For the investigated electrode D200 the system power of 75 W was applied, which is half of the maximum power of 150 W and lies in the range of usual values for this electrode applied in patient treatments in our clinic. For 75 W, a heating of 3.6 °C in 6 min in a depth of 1 cm in an agar-based, muscle tissue-equivalent phantom was achieved. The addition of a 1 cm thick, synthetic, low dielectric fat layer reduced the TR up until a depth of 8.5 cm by on average around 38% (from 8.5 cm onwards the absolute local TR is similar, deviations are ≤0.1 °C). In terms of point-to-point absolute SAR comparison (without any normalization), up to a depth of 11 cm in the phantoms central vertical plot, the simulation differs from the measured TR points by on average 25% (ranging from 7% to 36%) for the homogeneous phantom and by on average 43% (ranging from 26% to 60%) for the inhomogeneous phantom. Conclusion Computer simulations and experimental data were compared for the CHT system EHY-2030 using the D200 electrode, applying a thermal imaging technique for different vertically splittable phantoms. This pilot study data can be used as a guidance regarding the expected heating for this commonly used electrode size but also to further elucidate the significance of non-thermal anticancer effects. Further studies are needed for different sizes and geometries of electrodes and phantoms.

Enhancing solar flat plate collector efficiency with advanced phase change materials and expanded boron nitride

ABSTRACT Thermal energy storage, particularly through Phase Change Materials (PCMs), is gaining significant attention for its ability to enhance storage capacity and thermal conductivity. PCMs help alleviate the strain on renewable energy sources and stabilize load fluctuations. This study integrates a novel combination of LiNO3-NaSO4·10H2O-NaCl with boron nitride into Flat Plate Collectors (FPCs) to boost system performance. This Composite Phase Change Material (CPCM) increases latent heat value by up to 245.80 kJ, enhancing thermal decomposition and absorption rates while reducing heat losses. Boron nitride improves thermal conductivity by 25%, from 1.378 W/m·K to 5.543 W/m·K, increasing the CPCM's charging rate. The specific heat capacity rises from 4.2 J/g·°C to 5 J/g·°C at a maximum temperature of 90°C. As a result, the collector's efficiency improves by 15%, achieving an overall system efficiency of 88%. Water serves as the heat transfer fluid, and simulations are conducted using Python in Anaconda Jupyter Notebook.

Dynamic behavior and transfer characteristics of CO2-enriched bubbles within Spirulina sp. suspension under various aeration conditions using the high-speed imaging technique

The biological CO2 fixation method through microalgae photosynthesis has received considerable attention to alleviate the trend of global warming. CO2-enriched gas is generally aerated into the microalgae suspension in the form of bubbles through the gas distributors. Dynamic behavior and transfer characteristics of CO2-enriched bubbles are crucial to microalgae cells growth and CO2 bio-fixation. A visual experimental system based on the high-speed camera was constructed in this work to obtain the dynamic behavior and transfer characteristics of CO2-enriched bubbles within Spirulina sp. suspension. CO2-enriched bubbles movement and dissolution characteristics were comprehensively investigated under various CO2 concentrations, gas distributor aperture size, aeration rates, and Spirulina sp. biomass densities. Experimental results indicate that the optimal CO2 dissolution mass transfer and absorption rate were attained under the CO2 concentration of 5 %, gas distributor aperture diameter of 10 μm, and aeration rate of 0.1–0.3 vvm. Moreover, as Spirulina sp. biomass density increased, the bubble average diameter decreased, and rising velocity slowed while the volumetric mass transfer coefficient and CO2 absorption rate elevated. To summarize, this work may guide future efforts to enhance the photobioreactors (PBRs) performance from the perspective of aeration conditions optimization.

Dynamic tunable triple-band terahertz perfect absorber based on graphene metamaterial

This work developed a graphene-based perfect absorber with dynamic tuning capabilities. This absorber consists of a metal substrate, a layer of graphene square rings, a layer of graphene disks, and two layers of SiO2 dielectric sandwiched between them. Simulation results demonstrate absorption peaks at 1.23 THz, 4.2 THz, and 6.38 THz, with respective absorption rates of 99.9 %, 99.8 %, and 98.3 %. By analyzing the distributions of the electric field and surface current at the central frequencies of the three absorption peaks, the excitation mechanism of each absorption peak was discussed. It was found that by adjusting graphene's chemical potential, the absorption spectrum can be actively controlled. Furthermore, the absorber is insensitive to polarization and can sustain the stability of the absorption spectrum within an incident angle range of 0∼35°. This work has the potential to advance the research of multi-band terahertz absorbers, dynamically tunable devices, and other graphene-based photonic devices.

The roles of nanoparticle-enriched biochars in improving soil enzyme activities and nutrient uptake by basil plants under arsenic toxicity

Enriched biochar with improved properties and functionality can play a significant role in providing sustainable solutions for mitigating heavy metal contamination in soil. In this experiment, the effects of solid and enriched biochars (potassium-enriched biochar (BC-K), magnesium-enriched biochar (BC-Mg), both individually and combined) were examined on soil microbial and enzyme activities, as well as nutrient uptake by basil plants cultivated in a soil with three levels of arsenic (nontoxic, 50 mg As kg−1 soil, and 100 mg As kg−1 soil). Biochar-related treatments, increased soil organic matter (65–76%), while decreased availability of arsenic (6–55%) in the soil. The microbial biomass carbon (by about 123%) and soil basal respiration (by about 256%), and soil enzymatic activities (β-glucosidase, urease, alkaline phosphatase, and dehydrogenase) were enhanced by enriched biochars under arsenic toxicity. The solid and particularly enriched biochars decreased arsenic content and improved nitrogen and phosphorus contents of roots and shoots, root length, root activity, and root and shoot biomass in basil plants. Therefore, it is conceivable to suggest that enriched biochars are superior treatments for improving nutrient absorption rates and basil growth under arsenic toxicity through decreasing arsenic mobility and increasing soil microbial activities.

Investigation on CO2 capture performance of low-viscosity diamine non-aqueous absorbents with N-methyldiethanolamine regulation

In recent years, non-aqueous absorbents have attracted increasing attention due to their ability of significantly reducing sensible and latent heats in regeneration processes compared to conventional organic amine aqueous solution. But high viscosity of non-aqueous absorbents after CO2 absorption saturation became an obstacle to their industrial application. Here, a novel low-viscosity diamine non-aqueous absorbent for high-efficiency CO2 capture was proposed, in which N-methyldiethanolamine (MDEA) with steric hindrance effect was introduced as a regulator and dimethyl sulfoxide (DMSO) as a cosolvent. The effects of MDEA on CO2 capture performance of various non-aqueous absorbents and its regulation mechanism on CO2 absorbent viscosity were investigated systematically. Experimental results showed that when 25 wt% 2-(2-aminoethylamino)ethanol (AEEA) was screened as main CO2 absorption component, AEEA/MDEA/DMSO non-aqueous absorbent exhibited a high CO2 absorption capacity of 2.55 mol/kg and a fast CO2 absorption rate. Based on further mass fraction optimisation, it was found that the lowest viscosity of non-aqueous absorbents after CO2 absorption was 13.12 mPa s and the highest CO2 regeneration reached 93.5 % with AEEA and MDEA were 17.5 wt% and 12.5 wt%, respectively. 13C NMR tests showed that two characteristic peaks of carboxylated carbon appeared in CO2 products, which indicated that both amino groups on AEEA molecule were involved in CO2 absorption reaction. DFT calculations indicated that hydrogen bonding strength between MDEA and CO2 products was relatively lower than that of AEEA and CO2 products, which favored reducing absorbent saturation viscosity significantly. Thermodynamic analysis revealed that total regeneration energy consumption for 17.5 wt% AEEA/12.5 wt% MDEA/70 wt% DMSO non-aqueous absorbent was 1.72 GJ/t CO2, which was 53 % lower than that of MEA aqueous solution.

First Principles Study of Electronic and Optical Properties of Al-P Co-Doped ZnO in the Presence of Zn Vacancies.

The BP neural network optimized by the Adam algorithm was used to predict the defect formation energy of Al-P co-doped ZnO systems with different concentrations of P replacing O under the presence of different concentrations of VZn. It was found that the easily formed AlZnPo-1VZn, AlZnPO-2VZn, and AlZn2PO-1VZn systems. The first principles of density function were used to study the geometric, electronic, and optical properties of each system. The simulation results show that the bandgap values of the three systems have decreased relative to the intrinsic ZnO, among which AlZnPO-1VZn and AlZnPO-2VZn is still a p-type conductive system, AlZnPO-2VZn has the highest conductivity. From the analysis of reflectivity, absorption rate, and light transmittance, AlZn2PO-1VZn has the most relatively excellent optical properties, followed by AlznPo-2VZn.

In vivo imaging of the human brain with the Iseult 11.7-T MRI scanner.

The understanding of the human brain is one of the main scientific challenges of the twenty-first century. In the early 2000s, the French Atomic Energy Commission launched a program to conceive and build a human magnetic resonance imaging scanner operating at 11.7 T. We have now acquired human brain images in vivo at such a magnetic field. We deployed parallel transmission tools to mitigate the radiofrequency field inhomogeneity problem and tame the specific absorption rate. The safety of human imaging at such high field strength was demonstrated using physiological, vestibular, behavioral and genotoxicity measurements on the imaged volunteers. Our technology yields T2 and T2*-weighted images reaching mesoscale resolutions within short acquisition times and with a high signal and contrast-to-noise ratio.

Assessing Human Iron Kinetics Using Stable Iron Isotopic Techniques.

Stable iron isotope techniques are critical for developing strategies to combat iron deficiency anemia, a leading cause of global disability. There are four primary stable iron isotope methods to assess ferrokinetics in humans. (i) The fecal recovery method applies the principles of a metabolic balance study but offers enhanced accuracy because the amount of iron isotope present in feces can be directly traced back to the labeled dose, distinguishing it from endogenous iron lost in stool from shed intestinal cells. (ii) In the plasma isotope appearance method, plasma samples are collected for several hours after oral dosing to evaluate the rate, quantity, and pattern of iron absorption. Key metrics include the time of peak isotope concentration and the area under the curve. (iii) The erythrocyte iron incorporation method measures iron bioavailability (absorption and erythrocyte iron utilization) from a whole blood sample collected 2 weeks after oral dosing. Simultaneous administration of oral and intravenous tracers allows for separate measurements of iron absorption and iron utilization. These threemethods determine iron absorption by measuring tracer concentrations in feces, serum, or erythrocytes after administration of a tracer. In contrast, (iv) in iron isotope dilution, an innovative new approach, iron of natural composition acts as the tracer, diluting an ad hoc modified isotopic signature obtained via prior isotope administration and equilibration with body iron. This technique enables highly accurate long-term studies of iron absorption, loss, and gain. This review discusses the application of these kinetic methods and their potential to address important questions in hematology andiron biology.

Silk fibroin/chitosan-based anal fistula scaffolds loaded with curcumin and 5-aminosalicylic acid

The present work describes the development of silk fibroin (SF)/chitosan (CS)-based porous composite anal fistula scaffold (SCAFS) with anti-inflammatory and healing functions. The SCAFS comprises an inner layer made from degummed silk fiber using a vertical braiding machine, and an outer layer created by freeze-drying a mixture of short SF fibers and curcumin (CUR)/5-aminosalicylic acid (5-ASA) loaded SF/CS solution. Results revealed that the SCAFS has high porosity of 42.4 %, remarkable water absorption rate of 370.5 %, robust dry/wet compression resistance of 12.28 ± 2.61 N/3.08 ± 0.43 N. The in vitro &in vivo biocompatibility and anti-inflammatory effect of SCAFS were further examined. The expression of pro-inflammatory cytokine TNF-α, anti-inflammatory cytokine IL-10, CD31 and CD68 was determined by immunohistochemistry (IHC) staining, H&E staining, Immunofluorescence (IF) staining and Masson assay. The results showed that the scaffolds possess a sustainable drug release above 400 h, better biocompatibility and anti-inflammatory effect than the control groups (p < 0.05). Thus, the SCAFS has potential application in the treatment of Crohn's disease.

A broadband tunable THz sensor based on graphene metasurface

In this paper, we design a polarization-independent and angle-insensitive wideband THz graphene metamaterial sensor. The proposed metasurface sensor consists of six layers, which are silicon dioxide substrate, metal reflector, air layer, graphene metasurface with microstructure, ion-gel layer and silicon dioxide dielectric layer from bottom to top. The sensor was simulated by using CST Microwave Studio software, and the absorption and sensing performance were analyzed. The results show that the absorption rate is more than 95 % in the range of 1.05–4.07 THz. In addition, when the Fermi energy level of graphene is changed, the absorption rate can be adjusted from 20 % to more than 95 %. At the same time, the absorptivity of the device can be maintained above 80 % before 60° when the TE and TM waves are incident, and it is insensitive to the polarization angle due to the central symmetry of the graphene surface microstructure. By changing the thickness of the air layer, the device can achieve maximum absorption at h2=30μm, where the maximum frequency shift sensitivity is 2.179 THz/RIU. The influence of structure parameters and incident angle on the absorption spectrum shows that the proposed structure has good stability. The proposed metasurface sensor has potential application prospects in biological detection and medical monitoring, broadening the application range of THz functional devices.