Absorption Of Microwave Energy Research Articles

Temperature-dependent dielectric properties of the Korean lunar simulant and ilmenite: Lunar microwave processing potential

There is increasing interest in the potential application of microwave sintering technology in the construction of infrastructure on the Moon. This study aimed to characterize the dielectric properties of in situ lunar materials; this information is critical for an understanding of the interaction of these materials with microwave and in the application of microwave sintering technology. Dielectric properties including the real and imaginary permittivity, dielectric loss tangent, penetration depth, and electrical conductivity of Korean Lunar Simulant (KLS-1) and ilmenite (an abundant lunar mineral) were investigated at microwave frequencies as a function of temperature. X-ray dispersion (XRD) analyses confirmed that the lattice expansion of minerals with increasing temperature was consistent with an increasing trend in permittivity. The dielectric loss tangent of ilmenite was 2–36 times higher than that of KLS-1, depending on temperature, indicating that ilmenite has greater ability to absorb microwave energy, converting it to heat. Ilmenite demonstrated rapid heating to 1000°C within a few minutes on exposure to 1 kW microwave (2.45 GHz) irradiation. This study provides important information relevant to the development of microwave technology for future lunar applications.

Microwave responsive copper-ferrite (CuFe2O4) encapsulated in molybdenum-disulfide (MoS2) nanoflower catalyst for antibiotic removal via persulfate oxidation

Microwave (MW) responsive copper-ferrite/molybdenum-disulfide (CuFe2O4/MoS2) nanoflower catalyst was implemented for rapid antibiotic metronidazole (MNZ) degradation via persulfate oxidation under MW irradiation. The catalyst was synthesized via co-precipitation followed by hydrothermal methods, and characterized by XRD, FTIR, SEM, TEM, VSM, XPS, and UV-DRS. As a first step, MW induced MNZ removal was studied at different initial mass of CuFe2O4/MoS2 (2.5–20%), where 5% CuFe2O4 in the nanocomposite performed the best. Within 5 min of MW irradiation, 100% MNZ removal was observed (Kobs ∼ 1.063 min−1) under the optimal reaction conditions (i.e., CuFe2O4/MoS2 dose ∼ 0.4 g/L; PS dose ∼ 100 mg/L; temperature ∼ 90 °C; and MW power ∼ 350 W). The MNZ removal was independent of solution pH 3–11, and the removal was by SO4•−and •OH radicals alongside the limited contribution from O2•−. PS and H2O were thermally decomposed to produce SO4•−and •OH radicals, whereas intrinsic semiconductor CFO/MS with a narrow bandgap of 1.53 eV allowed electrons to jump into conduction band from valance band to create SO4•− and O2•−. However, the performance of MW system was inhibited by the presence of anions in the order of Cl−< NO3− <CO32− <H2PO4−. Robustness of the CuFe2O4/MoS2 was proved via recyclability experiments, and MNZ removal was found to be dropped ∼ 4.89% at the end of 5th cycle. It was proposed that the absorbed MW energy was dissipated through various losses to generate ‘hotspots’ (>1200 °C) for MNZ removal. Synergistically, redox couples of transitional metals contributed to MNZ degradation.

Microwave absorption, thermal and mechanical properties of amorphous nano carbon doped aluminium nitride composite ceramics

Low-cost amorphous nano-carbon (ANC) was employed as an absorbent to modify the microwave performance of AlN ceramics (AlN-4 wt% Y2O3-x wt% C, x = 0, 2.0, 3.8, 3.9, 4.0) via hot-pressing sintering, and the thermal and mechanical properties were also investigated. With the increase of ANC content from 0 to 4.0 wt%, the relative density of AlN composite decreases from 3.28 g cm−3 to 3.16 g cm−3 when sintered at 1800 °C for 2 h, and with the increase of sintering temperature from 1700 °C, the density of the 4.0 wt% ANC doped AlN composite presents trend of increase and reaches the maximum value of 3.16 g cm−3 at 1800 °C and then decreases. The XRD pattern shows that the composites are composed of AlN and Y–Al–O (YAG, YAP, YAM et al.) phases. SEM results indicate that average grain sizes for AlN and secondary phases gradually decrease with increasing carbon content, suggesting inhibited grain growth due to ANC addition. No obvious changes in phase constitution nor intensity changes were detected with the increase in carbon content and sintering temperature. As the carbon content increases from 0 to 4.0 wt%, the dielectric constant gradually increases from ∼9 to 13.89 at 10 GHz, the dielectric loss gradually increases from the vicinity of 10−3 to 0.38 at 10 GHz, and the reflective loss decreases from −27.92 dB to −49.40 dB, the thermal conductivity of the AlN-ANC composite decreases from 116.63 W m−1 K−1 to 50.13 W m−1 K−1. In addition, with 4.0 wt% ANC addition, the dielectric constant, dielectric loss, reflective loss, hardness, elastic modulus, bending strength, and fracture toughness are 13.89, 0.38, 49.40 dB, 6.4 ± 0.4 GPa, 262 GPa, 268.78 MPa, and 1.4 ± 0.1 MPa m1/2, respectively. Its ability to efficiently absorb microwave energy enhances the performance of devices including radar systems, communication equipment, and microwave heating systems, making it a promising candidate for microwave vacuum electronic applications.

Advanced Integration of Microwave Kiln Technology in Enhancing the Lost-Wax Glass Casting Process: A Study on Methodological Innovations and Practical Implications

Lost-wax glass casting, an esteemed yet technically demanding art form, traditionally relies on specialized, costly kiln equipment, presenting significant barriers to artists regarding equipment affordability, energy efficiency, and the technical mastery required for temperature control. Therefore, this study introduces an innovative approach by integrating a microwave kiln with standard household microwave ovens, thus facilitating the lost-wax glass casting process. This methodological adaptation allows artists to employ readily available home appliances for glass creation, significantly reducing the process’s cost and complexity. Our experimental investigations reveal that, by using a 500W household microwave oven for heating, the silicon carbide (SiC) in microwave kilns can efficiently absorb microwave energy, allowing the kilns to reach temperatures exceeding 700 °C, a critical threshold for casting glass softening. We further demonstrate that by adjusting the number of heating cycles, producing high-quality, three-dimensional(3D) glass artworks is feasible, even for large-scale projects. In addition, the microwave kiln can be used as an effective cooling tool to uniformly cool the formed casting glass. This study presents a possible alternative to conventional kiln technology and marks a paradigm shift in glassmaking, offering a more accessible and sustainable avenue for artists and practitioners.

Velocity match between plasma and flame in microwave-assisted spark ignition

As a prospective ignition technique, microwave-assisted spark ignition (MAI) can accelerate flame and thus satisfy the demand for effective ignition. However, its acceleration mechanism on flame velocity is still unclear, which hinders its application and optimizations. Therefore, this research focuses on understanding the flame acceleration mechanism behind MAI. In this paper, MAI is achieved through radiating a microwave pulse after spark ignition. The flame velocity and the precise absorbed energy under different combustion conditions are investigated with flame kernel's Schlieren images and microwave energy diagnostics, respectively. The results show that MAI accelerates flame primarily by the interaction between microwave plasma and flame front, rather than the free electrons within the flame. Specifically, microwave accelerating flame takes two processes: energy absorption, and velocity match. Energy absorption refers to the microwave energy absorbed by residual electrons after ignition to generate and sustain microwave plasma, while velocity match involves the outward plasma with faster velocity propelling the slower flame front. Moreover, the plasma velocity shows a positive relationship with absorbed microwave energy. The velocity match between microwave plasma and flame is important to successful flame acceleration. Besides, the efficiency of energy absorption and flame acceleration varies with plasma type (glow or incandescent). Glow plasma is characterized by effective flame acceleration but relatively low absorption efficiency, and incandescent plasma is in reverse. The maximum absorption efficiency can be elevated to 70 % with incandescent plasma occurring. Ultimately, the plasma velocity declines with its traveled distance, which might impair the flame acceleration.

Superparamagnetic iron oxide nanoparticle enhanced percutaneous microwave ablation: Ex-vivo characterization using magnetic resonance thermometry.

Percutaneous microwave ablation (pMWA) is a minimally invasive procedure that uses a microwave antenna placed at the tip of a needle to induce lethal tissue heating. It can treat cancer and other diseases with lower morbidity than conventional surgery, but one major limitation is the lack of control over the heating region around the ablation needle. Superparamagnetic iron oxide nanoparticles have the potential to enhance and control pMWA heating due to their ability to absorb microwave energy and their ease of local delivery. The purpose of this study is to experimentally quantify the capabilities of FDA-approved superparamagnetic iron oxide Feraheme nanoparticles (FHNPs) to enhance and control pMWA heating. This study aims to determine the effectiveness of locally injected FHNPs in increasing the maximum temperature during pMWA and to investigate the ability of FHNPs to create a controlled ablation zone around the pMWA needle. PMWA was performed using a clinical ablation system at 915MHz in ex-vivo porcine liver tissues. Prior to ablation, 50uL 5mg/mL FHNP injections were made on one side of the pMWA needle via a 23-gauge needle. Local temperatures at the FHNP injection site were directly compared to equidistant control sites without FHNP. First, temperatures were compared using directly inserted thermocouples. Next, temperatures were measured non-invasively using magnetic resonance thermometry (MRT), which enabled comprehensive four-dimensional (volumetric and temporal) assessment of heating effects relative to nanoparticle distribution, which was quantified using dual-echo ultrashort echo time (UTE) subtraction MR imaging. Maximum heating within FHNP-exposed tissues versus control tissues were compared at multiple pMWA energy delivery settings. The ability to generate a controlled asymmetric ablation zone using multiple FHNP injections was also tested. Finally, intra-procedural MRT-derived heat maps were correlated with gold standard gross pathology using Dice similarity analysis. Maximum temperatures at the FHNP injection site were significantly higher than control (without FHNP) sites when measured using direct thermocouples (93.1±6.0°C vs. 57.2±8.1°C, p=0.002) and using non-invasive MRT (115.6±13.4°C vs. 49.0±10.6°C, p=0.02). Temperature difference between FHNP-exposed and control sites correlated with total energy deposition: 66.6±17.6°C, 58.1±8.5°C, and 20.8±9.2°C at high (17.5±2.2kJ), medium (13.6±1.8kJ), and low (8.8±1.1kJ) energies, respectively (all pairwise p<0.05). Each FHNP injection resulted in a nanoparticle distribution within 0.9±0.2cm radially of the injection site and a local lethal heating zone confined to within 1.1±0.4cm radially of the injection epicenter. Multiple injections enabled a controllable, asymmetric ablation zone to be generated around the ablation needle, with maximal ablation radius on the FHNP injection side of 1.6±0.2cm compared to 0.7±0.2cm on the non-FHNP side (p=0.02). MRT intra-procedural predicted ablation zone correlated strongly with post procedure gold-standard gross pathology assessment (Dice similarity 0.9). Locally injected FHNPs significantly enhanced pMWA heating in liver tissues, and were able to control the ablation zone shape around a pMWA needle. MRI and MRT allowed volumetric real-time visualization of both FHNP distribution and FHNP-enhanced pMWA heating that was useful for intra-procedural monitoring. This work strongly supports further development of a FHNP-enhanced pMWA paradigm; as all individual components of this approach are approved for patient use, there is low barrier for clinical translation.

Decreasing the environmental impact of carbon fibre production via microwave carbonisation enabled by self-assembled nanostructured coatings

The use of carbon fibre (CF)-based composites is of growing global importance due to their application in high-end sectors such as aerospace, automotive, construction, sports and leisure amongst others. However, their current high production cost, high carbon footprint and reduced production capability limit their use to high-performance and luxury applications. Approximately 50% of the total cost of CF production is due to the thermal conversion of polyacrylonitrile (PAN) precursor fibre (PF) to CF as it involves the use of high energy consumption and low heating efficiency in large furnaces. Looking at this scenario, this study proposes in the present study to use microwave (MW) heating to convert PF to CF. This is scientifically and technologically challenging since PF does not absorb microwave energy. While MW plasma has been utilised to carbonise fibres, it is the high temperature from the plasma that does the carbonisation and not the MW absorption of the fibres. Therefore, for the first time, this research shows how carbonisation temperatures of >1000 °C can be reached in a matter of seconds through the use of a novel microwave (MW) susceptor nanocoating methodology developed via a layer-by-layer assembly of multiwall carbon nanotubes (MWCNTs) on the PF surface. Remarkably, these CFs can be produced in an inexpensive domestic microwave and exhibit mechanical performance equivalent to CF produced using conventional heating. Additionally, this study provides a life cycle and environmental impact analysis which shows that MW heating reduces the energy demand and environmental impact of lignin-based CF production by up to 66.8% and 69.5%, respectively.Graphical

The Law and Mechanism of the Effect of Surface Roughness on Microwave-Assisted Rock Breaking

In physical engineering, a rock surface, whether naturally or artificially formed, is rough. When irradiating rocks, microwaves produce reflections and diffractions on the surface of rough rocks, which significantly affect the absorption of microwave energy by rocks, thus influencing the result of microwave irradiation. In order to explore the influence of rough rock surfaces on the effect of microwave-assisted rock breaking, microwave irradiation tests were carried out on basalt samples with different values of roughness to test the temperature and P-wave velocity of the samples before and after microwave irradiation. Numerical test methods were used to systematically study the influence of rough rock surfaces on microwave irradiation. The results show that, under the same microwave irradiation conditions, the effect of microwave irradiation on rough surface basalt is more significant than that of flat surface basalt. The surface temperature distribution range of flat surface specimens is narrow, the surface temperature range of rough surface specimens is wider and more inhomogeneous, and the maximum surface temperatures of rough surface specimens are much higher than those of flat surface specimens. After irradiation, new macroscopic cracks were generated on the surface of the samples, and the crack propagation of the rough surface samples was more obvious. The decrease in P-wave velocity before and after the irradiation of flat surface samples is small, and that of rough surface samples is larger. The main factors affecting the effect of microwave irradiation on the rough surface are the refraction and reflection of electromagnetic waves, heat conduction, and stress concentration on the surface.

The 3D Printing of Novel Honeycomb-Hollow Pyramid Sandwich Structures for Microwave and Mechanical Energy Absorption.

Honeycomb sandwich (HS) structures are important lightweight and load-bearing materials used in the aerospace industry. In this study, novel honeycomb-hollow pyramid sandwich (HPS) structures were manufactured with the help of fused deposition modeling techniques using PLA and PLA/CNT filaments. The microwave and mechanical energy absorption properties of the HPS structures with different geometry parameters were studied. Compared with the HS structure, the HPS structure enhanced both microwave absorption and mechanical properties. The HPS structures possessed both broadband and wide-angle microwave absorption characteristics. Their reflection loss at 8-18 GHz for incident angles of up to 45° was less than -10 dB. As the thickness of the hollow pyramid increased from 1.00 mm to 5.00 mm, the compressive strength of the HPS structure increased from 4.8 MPa to 12.5 MPa, while mechanical energy absorption per volume increased from 2639 KJ/m3 to 5598 KJ/m3. The microwave absorption and compressive behaviors of the HPS structures were studied.

Kinetic study of Ni-M/CNT catalyst in methane decomposition under microwave irradiation

Methane catalytic decomposition has been studied with catalysts that can attenuate the energy of electromagnetic waves to heat and drive the reaction. Herein, we report, for the first time, a comprehensive kinetic study of Ni-M (M=Pd, Cu, or Fe)-CNT catalysts under microwave irradiation. These binary metal alloy nanoparticles have been synthesized on multiwalled carbon nanotube support with solvothermal process. These catalysts showed incredible performance for both absorbing microwave energy and catalyzing the reaction to form carbon nanotubes and hydrogen. Ni-M-CNT has a reaction order of 0.74. 10Ni-1 Pd-CNT, 10Ni-1Cu-CNT, and 10Ni-1Fe-CNT have activation energies at 87, 75, and 69 kJ/mol. The investigation was carried out in a differential reactor. The results indicated that 10Ni-1Fe-CNT had the lowest activation energy due to the increase in microwave susceptibility. This work pioneered the microwave catalytic methane decomposition field as well as paving the way for future electrification of COx-free hydrogen production.

The Evolution of Microwave-Induced Thermoacoustic Signals Generated During Pulsed Microwave Ablation in Bovine Liver

The temperature dependence of microwave-induced thermoacoustic signals generated in tissue may be exploited to monitor microwave ablation in real-time. We present an experimental study investigating the evolution of microwave-induced thermoacoustic signals that are generated within an ablation zone during microwave ablation in bovine liver tissue. An X-band interstitial coaxial ablation antenna is used to simultaneously heat liver tissue to temperatures up to 90 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$^{\circ }$</tex-math></inline-formula> C and excite thermoacoustic signals via the absorption of pulsed microwave energy. Thermoacoustic signals are detected using a single-element ultrasound transducer located at the surface of the tissue. Both fresh and boiled liver tissue samples are used in experiments to decouple the influence of temperature and tissue coagulation on thermoacoustic signal characteristics. We identify two thermoacoustic signal characteristics of interest: arrival time of the pulse at the ultrasound receiver and the energy in the pulse. We find that the time difference of arrival over the course of microwave ablation grows in magnitude due to temperature-dependent speed of sound and tissue shrinkage. Thermoacoustic signal energy generally increases throughout microwave ablation, implying an increasing temperature-dependent thermal expansion coefficient of liver tissue. Of the two characteristics, time difference of arrival shows the most promise as a trackable feature for monitoring microwave ablation in real time.

The microwave absorption and anti-corrosion performance of flaky FeSiCr powder coated by silane film

A silane film was prepared on the surface of flaky FeSiCr powder by sol-gel method. The phase and morphology of the samples were observed by X-ray Diffraction (XRD) and Transmission Electron Microscope (TEM), and the valence state and chemical composition of the elements were determined by X-ray Photoelectron Spectroscopy (XPS). The results showed that the observed images of homogeneous silane films confirm the successful preparation of lamellar FeSiCr@PFOTMS composites. The electromagnetic parameters measurement results showed that the complex permittivity of the samples is substantially reduced and the complex permeability changes little, then the balance of electromagnetic parameters is improved and the impedance matching is optimized. When PFOTMS is added in amounts up to 2 mL, the FeSiCr@PFOTMS composites showed the best microwave energy absorption and corrosion resistance. The minimum reflection loss value of the sample reached –32.22 dB at 2.16 GHz. The electrochemical test results showed that the open circuit corrosion potential of FeSiCr@PFOTMS composites with 2 mL PFOTMS increased from –0.217 V to 0.031 V, and the corrosion voltage increased from –0.215 V to 0.028 V. These results provide ideas for the preparation of multifunctional composites with both excellent microwave absorption properties and corrosion resistance in practical applications.

Ultra-fast solvent-free protocol remodels the large-scale synthesis of carbon dots for nucleolus-targeting and white light-emitting diodes

Carbon dots (CDs) provides unprecedented opportunities for optical applications due its unique properties, but the energy-extensive consumption, high-risk factor and time-consuming synthesis procedure greatly hinders its industrialization process. Herein, we proposed an ultra-low energy consumption solvent-free synthetic strategy for fast preparing green/red fluorescence carbon dots (G-/R-CDs) using m-/o-phenylenediamine and primary amine hydrochloride. The involvement of primary amine hydrochloride can improve the formation rate of G-CDs/R-CDs through effectively absorbing microwave energy and providing acid react environment. The developed CDs exhibit good fluorescence efficiency, optical stability and membrane permeability for dexterous bioimaging in vivo. Based on inherently high nitrogen content, the G-CDs/R-CDs possess excellent nuclear/nucleolus targeting ability, and were successfully applied for screening cancer and normal cells. Furthermore, the G-CDs/R-CDs were further applied for fabricating high-safety and high-color rendering index white light-emitting diodes, providing a perfect candidate for indoor lighting. This study opens up new horizons for advancing practical applications of CDs in related fields of biology and optics.

Effect of strong dielectric substances on the damage characteristics of rocks exposed to microwave radiation: Insight from experiments and mechanisms

It has been demonstrated that microwave pretreatment can weaken rocks, reduce tool wear, and improve mechanical rock breaking efficiency. The dielectric properties of rock minerals are a major factor affecting the ability of rocks to absorb microwaves, so it is important to conduct experimental research on rock modification to improve the microwave absorption capacity of rocks. The concept of “microwave-assisted absorbing reagents” has been proposed to increase the microwave absorption capacity of rocks. Sandstone specimens are first pretreated with strong dielectric substances before being exposed to microwave radiation to increase their microwave absorption capacity, then they are exposed to microwave fields and finally conducted to uniaxial compression tests. Enhancement in microwave absorption capacity of sandstone specimens is showed by P-wave velocity, nuclear magnetic resonance, and mechanical tests before and after microwave treatment. The results showed that barium titanate suspension and water are both effective microwave-assisted absorbing agents. The specimens treated with barium titanate suspension exhibited better microwave absorption capacity; in 5 kW microwave power irradiation, its p-wave velocity falls by 14.04%, porosity rises by 25.43%, and uniaxial compressive strength falls by 24.98%. Additionally, the failure form of sandstone specimens changes from brittle to plastic once it has fully absorbed microwave energy.

Differential Evolution Optimization of Microwave Focused Hyperthermia Phased Array Excitation for Targeted Breast Cancer Heating.

Microwave hyperthermia using the phased array applicator is a non-invasive treatment modality for breast cancer. Hyperthermia treatment planning (HTP) is critical to accurately treating breast cancer and avoiding damage to the patient's healthy tissue. A global optimization algorithm, differential evolution (DE) algorithm, has been applied to optimize HTP for breast cancer and its ability to improve the treatment effect was proved by electromagnetic (EM) and thermal simulation results. DE algorithm is compared to time reversal (TR) technology, particle swarm optimization (PSO) algorithm, and genetic algorithm (GA) in HTP for breast cancer in terms of convergence rate and treatment results, such as treatment indicators and temperature parameters. The current approaches in breast cancer microwave hyperthermia still have the problem of hotspots in healthy tissue. DE enhances focused microwave energy absorption into the tumor and reduces the relative energy of healthy tissue during hyperthermia treatment. By comparing the treatment results of each objective function used in DE, the DE algorithm with hotspot to target quotient (HTQ) as the objective function has outstanding performance in HTP for breast cancer, which can increase the focused microwave energy of the tumor and decrease the damage to healthy tissue.

Radio-absorbing properties of (1-x)BiFeO3 – xLaMnO3 (0.1 ≤ x ≤ 0.9) solid solutions

In the frequency range of 3.2–12 GHz, the microwave energy absorption spectra of a series of the (1-x)BiFeO3 – xLaMnO3 solid solutions with a concentration of x = 0.1 − 0.9 were studied. The spectra contain the absorption maxima of the resonant type, the magnitudes, resonant frequencies, and number of which depend on the x concentration and temperature. At different heights from the surface of the samples under study, located on the microstrip line, the emission spectra of the electric and magnetic components of the microwave field were obtained. The X-ray diffraction data and the obtained absorption and emission spectra are interconnected and complement each other. The features of the spectra are discussed from the point of view of the contribution to the emission and absorption of the energy of the dielectric walls of the twins resonating in the electromagnetic field. The features of the magnetic moments of multiferroics are also discussed.

マイクロ波特異効果はあるのか？ 有機合成反応における実験的検証

Highly polar compounds are generally heated by absorbing microwave energy. Since 1986, microwave irradiation has been applied to various organic syntheses as an efficient heating method. On the other hand, an additional effect called “microwave specific effect”, that cannot be explained by the simple heating effect, has been observed. In a solvent that absorbs less microwave, microwave energy can be directly provided to the reaction substrate, and microwave-specific effects can be expected. Some microwave-assisted asymmetric synthetic reactions have been observed to accelerate while maintaining enantioselectivity. Based on this working hypothesis, we experimentally confirmed the microwave-specific effect in several organic synthetic reactions.

Microwave heating of biomass waste residues for sustainable bioenergy and biomass materials preparation: A parametric simulation study

Sustainable bioenergy and biomass materials preparation from biomass waste residues using microwave heating has attracted widespread attention. However, the microwave heating process still has limitations of uneven temperature distribution and low energy conversion efficiency. This study constructed a coupled electromagnetic and heat transfer model for the microwave heating of waste tobacco stem (TS) biomass using COMSOL Multiphysics® software. The microwave heating behavior of TS biomass was predicted using the finite element method for different parameters, and this model has been experimentally verified to be dependable with a maximum relative error of less than 10%. Simulation results show that hot spots caused by interface polarization and standing waves generate inhomogeneous temperature distributions. The microwave cavity design with two waveguides and controlled frequency changes can improve microwave energy absorption and heating uniformity. A suitable microwave power can improve efficiency and reduce energy consumption during heating. Meanwhile, the TS biomass with 30% moisture content and in the cavity's low region (0–10 cm) can make maximum use of microwave energy, and the average and maximum energy efficiency achieve 59.15% and 87.79%, respectively. The results provide technical support and new perspectives for preparing sustainable bioenergy and biomass materials from waste TS biomass via microwave irradiation.

Two enhancements in microwave-assisted spark ignition and their causes

As a prospective ignition technique, microwave-assisted spark ignition (MAI) efficiently enhances ignition with plasma absorbing microwave energy. This paper achieves MAI through radiating a single 0.2 ms microwave pulse after the initial spark ignition, and investigates the ignition performance and the precise absorbed energy of MAI in different absorption patterns. The absorption pattern is tailored by the microwave pulse power. The results show that the enhancement of MAI can be divided into two categories based on ignition performance and absorbed energy: the glow enhancement and the incandescence enhancement. Compared to the glow enhancement, the incandescence enhancement has a greater energy absorption efficiency and thus induces more significant ignition enhancement. Additionally, the effect of gas parameters, including gas pressure and components, on these two enhancement categories is studied. Increasing pressure or decreasing methane concentration facilitates the generation of incandescence enhancement. Ultimately, the causes of both enhancements are discussed. The incandescence enhancement may be originated from the ionization of metal particles in the microwave field, whereas the glow enhancement is attributed to gas ionization. This work highlights the potential application of metal-microwave discharge on MAI, which can play a crucial role in suiting different conditions and further understanding the mechanisms of MAI.

Unusual heating effect of the elliptically polarized microwave electric field on sodium chloride solution: A molecular dynamics simulation

Our molecular dynamics simulation results show that the elliptically polarized microwave electric field would increase the heating efficiency of sodium chloride solution. The growth rate of the heating efficiency is positively correlated with the concentration of the sodium chloride solution and intensity of applied electric field. The rotation autocorrelation function results confirm that water molecules would do a more frequent rotational motion with the multidirectional polarization of elliptically polarized microwave electric field. The result of the more frequent rotational motion is consistent with that of the higher microwave energy absorption of energy analysis. The following analysis of hydrogen bond shows that the existence of ionic solutes would break the hydrogen bonds between water molecules and make it easier for water molecules to rotate with the applied electric field. These results indicate that elliptically polarized microwave electric field can indeed improve the heating efficiency of salt solution.