Absence Of Flame Research Articles

Estimation of Spectral Emissivity and S/Cu Ratio From Emissions of Copper Concentrates at the Flash Smelting Process

The project focused on the investigation of new sensing techniques in the copper production industry, specifically in the flash smelting of copper concentrate process. In this paper, we report a direct relationship between the visible and near-infrared emission spectra in the combustion of copper concentrates by changing some operating conditions such as the sulfur-copper and the oxygen ratios provided to the reaction zone. Spectral processing techniques are applied to the measured spectra. The first one aims to separate both continuous radiations mainly associated to incandescent particles and heating walls with discontinuous emissions associated with some emitting atoms and molecules. This goal was carried out using airPLS baseline estimation algorithm. The second processing technique aims to find the continuous emission only associated with the combustion of copper concentrate particles, eliminating the background spectra associated with the smelter walls. This goal was carried out by directly measuring walls emission at operating temperature and in the absence of flame. The most relevant results show that the estimation of the total radiation associated with each measured spectra is an intrinsic parameter of the process that can provide useful information to the operator that supervises the industrial process. It allows estimate quantitatively the sulfur-copper ratio in order to online monitor the mineral characteristics of the copper concentrate that is entering the process. On the other hand, the approach of a first prototype of the emissivity model for the copper concentrate particles, which validated with measurements, becomes a promising tool that will allow increasing the development of optoelectronic applications around this industry process.

Experimental Validation of a Solid-Phase Model for Wood Ignition and Burning

An unsteady one-dimensional model for the solid phase is applied to simulate the spontaneous ignition and burning of thick wood samples with grain orientation parallel or perpendicular to incident heat fluxes in the range 18-40kW/m2, that is, in the absence of flame. The description of heat and mass transfer processes, at constant gas pressure, is combined with global volumetric rates of wood decomposition and char oxidation. Surface regression occurs for a limit value of char density while a critical surface temperature describes ignition. Good quantitative predictions are obtained for the ignition times and the surface temperature and mass loss rate profiles during burning. Conversion always consists of three main stages. The first short transients correspond to the formation of a relatively thin charred surface layer and glowing ignition. The second much longer stage represents a pseudo-steady state burning, where the rates of advancement of the decomposition and oxidation zones are approximately const...

연소화염이 존재하는 봉대평판 갭에서 봉전극 형상에 따른 공기의 방전 특성

In this paper, discharge characteristics of air in the vertical arrangement of three rods(dome-shaped, cylinder-shaped, and needle-shaped rod) and plane gap having propane flame on the plane electrode are examined under the application of a.c. and d.c. high-voltages. As the result of the experiment, flashover voltages in the presence of the flame are substantially lowered than those in the absence of flame, and relative a.c. flashover voltages in the dome-shaped, cylinder-shaped, and needle-shaped rod gaps are found 32.5%, 32.1%, and 26.4% respectively. The polarity effects with the d.c. voltages are shown, and flashover voltages in negative polarity are much lowered than those in positive one. The negative flashover voltages in the dome-shaped and cylinder-shaped gaps are found 18.3% and 18.7% respectively, but the positive ones are found 53.5% and 43.2% respectively. In the needle-shaped rod gaps, meanwhile, the flame is extinguished by corona wind, and the quenching voltages are found 28.4% under the application of a.c. voltages. The ion winds of corona and the reduction of air density are the main factors of flashover reduction owing to the flame in the case of a.c. voltages, but the electrifications of the positive ion by thermal ionization besides the above factors are remarkably found in the case of d.c. voltages.

선도체 대 평면전극 갭에서 평면전극에 연소화염 존재시 대기의 절연파괴 특성

Breakdown characteristics of air in the vertical arrangement of line conductor and plane electrode in case of combustion flame on the plane electrode are examined by the application of AC. and DC voltages to the gap. In order to investigate the effect of paraffin flame on the breakdown characteristics of air, flashover voltages are measured according to the variation of the gap length and the horizontal distance between the flame and the line conductor. As the result of the experiment, flashover voltages are substantially lowered down to 29.8% in case of the AC voltage, and 16.1% in case of the negative DC voltage, when in the presence of the flame. from 100% when in the absence of flame. <BR> Flashover voltages of air in the range of smaller than 3㎝ at the horizontal distance are increased in the proportion of the gap length and the horizontal distance in case of both AC and negative DC voltages. But before the flashover occurs, the flame is extinguished by such corona wind that is produced from the line conductor when the gap length and the horizontal distance reach to a certain degree. The effect of relative air density and the phenomenon of thermal ionization are analysed as the reduction factors of flashover voltages, due to high temperature of the flame.

Planar Laser-Induced Fluorescence Fuel Imaging During Gas-Turbine Relight

This experimental study investigates the influence of fuel distribution on ignition outcome during high-altitude relight of a gas turbine. Planar laser-induced fluorescence is used to image fuel inside a lean direct-injection combustor under realistic conditions. A novel apparatus is developed to permit planar laser-induced fluorescence imaging, in which large quantities of poorly atomized fuel impinges on the internal surfaces of the combustor. Results reveal high variability in atomization quality. In the absence of flame, small droplets are confined to areas of recirculating flow, whereas large droplets impact on the walls. All fuel is introduced through a pilot air-blast atomizer close to the injector centerline. However, comparatively little fuel is apparent near the igniter tip because the outside swirlers of the fuel injector create a fast-moving stream of fuel-free air that flows directly below the upper combustor wall. The droplet size and fuel concentration in the main recirculation zone do not differ radically at test conditions with markedly different fuel-to-air ratios, suggesting that turbulent straining is a more important factor than equivalence ratio in the failure of ignition when the airflow rate is high. In the presence of flame, medium-sized burning droplets are observed close to the injector centerline. Flame interference resulting from fluorescence of polycyclic aromatic hydrocarbons is apparent, but small, suggesting that kerosene planar laser-induced fluorescence is a useful tool for the analysis of all stages of altitude relight.

평단봉대평판 전극배치에서 평판 전극에 화염이 존재할 때 공기의 섬락전압 특성

In this paper, flashover characteristics of air in the vertical arrangement of cylinder-shaped rod and plane gap in the case of combustion flame on the plane electrode were examined under the application of a.c. and d.c. high-voltages. In order to investigate the effect of propane flame on the flashover characteristics of air, flashover voltages in accordance with the variation of the gap length and the horizontal distance between the flame and the high-voltage rod electrode were measured. As the result of the experiment, flashover voltages in the presence of the flame were substantially lowered than those in the absence of flame, and the polarity effects with the d.c. voltages on appeared owing to the flame. Flashover voltages of air were increased in the proportion of the gap length and the horizontal distance in the case of both a.c. and d.c. voltages, but the flame was extinguished by such corona wind that was produced from the rod electrode when the gap length and the horizontal distance reached to a certain degree.

Factors influencing spontaneous combustion of solid waste

Landfill fires create a critical problem for landfill operators and require investigation of its occurrence and the conditions that favor its initiation. Subsurface fires are considered the most significant due to the difficulty in determining their location and extent. These fires are mainly caused by spontaneous combustion, combustion due to high temperature in absence of flame. This study investigates the effect of moisture content, oxygen concentration and leachate components on spontaneous ignition, combustion initiation, and self-heating of solid waste. A new procedure for testing spontaneous ignition is described; however, variations in solid waste components and landfill conditions can create some limitations to its use. The presence of water and dissolved solids in leachate was found to accelerate chemical self-heating of the solid waste. Oxygen concentration at 10% by volume can sustain chemical oxidation but did not promote accelerated burning.