3D Planning System Research Articles

Dose-volume analysis for quality assurance of interstitial brachytherapy for breast cancer

Purpose/Objective: The use of brachytherapy in the management of breast cancer has increased significantly over the past several years. Unfortunately, few techniques have been developed to compare dosimetric quality and target volume coverage concurrently. We present a new method of implant evaluation that incorporates computed tomography-based three-dimensional (3D) dose-volume analysis with traditional measures of brachytherapy quality. Analyses performed in this fashion will be needed to ultimately assist in determining the efficacy of breast implants. Methods and Materials: Since March of 1993, brachytherapy has been used as the sole radiation modality after lumpectomy in selected protocol patients with early-stage breast cancer treated with breast-conserving therapy. Eight patients treated with high-dose-rate (HDR) brachytherapy who had surgical clips outlining the lumpectomy cavity and underwent computed tomography (CT) scanning after implant placement were selected for this study. For each patient, the postimplant CT dataset was transferred to a 3D treatment planning system. The lumpectomy cavity, target volume (lumpectomy cavity plus a 1-cm margin), and entire breast were outlined on each axial slice. Once all volumes were entered, the programmed HDR brachytherapy source positions and dwell times were imported into the 3D planning system. Using the tools provided by the 3D planning system, the implant dataset was then registered to the visible implant template in the CT dataset. The distribution of the implant dose was analyzed with respect to defined volumes via dose-volume histograms (DVH). Isodose surfaces, the dose homogeneity index, and dosimetric coverage of the defined volumes were calculated and contrasted. All patients received 32 Gy to the entire implanted volume in 8 fractions of 4 Gy over 4 days. Results: Three-plane implants were used for 7 patients and a two-plane implant for 1 patient. The median number of needles per implant was 16.5 (range 11–18). Despite visual verification by the treating physician that surgical clips (with an appropriate margin) were within the boundaries of the implant needles, the median proportion of the lumpectomy cavity that received the prescribed dose was only 87% (range 73–98%). With respect to the target volume, a median of only 68% (range 56–81%) of this volume received 100% of the prescribed dose. On average, the minimum dose received by at least 90% of the target volume was 22 Gy (range 17.3–26.9), which corresponds to 69% of the prescribed dose. Conclusion: Preliminary results using our new technique to evaluate implant quality with CT-based 3D dose-volume analysis appear promising. Dosimetric quality and target volume coverage can be concurrently analyzed, allowing the possibility of evaluating implants prospectively. Considering that target volume coverage may be suboptimal even after radiographically verifying accurate implant placement, techniques similar to this need to be developed to ultimately determine the true efficacy of brachytherapy in the management of breast cancer.

Craniospinal axis irradiation in children. Treatment in supine position including field verification as a prerequisite for anesthesia without intubation.

For craniospinal axis irradiation in young children sometimes anesthesia is required. In order to minimize risks from the anesthesist's point of view supine position would be preferable to standard prone position. In case of irradiation in supine position verification of the 3-field junction in the cervical region causes problems, because there is no direct visual control. For such situations the clinical application of a new technique is presented. For treatment planning a modern 3D planning system was necessary. Patient's positioning was done by using a vacuum-form body immobilizer and an integrated head mask. Radiation fields were placed only by table movements being calculated by the planning system in relation to a reference point at the patient's surface. In addition to common verification films specially prepared small films were used for the 3-field junction in the cervical region. These films were placed close to the patient for the whole time of each radiation session being exposed by every radiation field. Two children (age 3 and 5 years, respectively) were irradiated as described. Twenty-eight of those specially prepared films were exposed. Two films (7%) had to be excluded because of inadequate exposure. An overlap of radiation fields was seen on 1 of the 26 remaining films (4%), whereas an unacceptable gap was not found. Acute skin reactions were comparable to those observed in patients being irradiated in standard prone position. The presented technique for craniospinal axis irradiation in supine position including field verification was not only precise and reproducable, but also comfortable and safe for the patient. We suggest it as a new option for craniospinal axis irradiation in children.

Conformal Proton Therapy for Prostate Carcinoma

Abstract Background: The role and optimum dose of radiation to eradicate prostate cancer continues to be evaluated. Protons offer an opportunity to increase the radiation dose to the prostate while minimizing treatment toxicity. Methods: Six hundred forty-three patients with localized prostate cancer were treated with protons, with or without photons. Treatments were planned with a 3D planning system; patients received 74–75 CGE (Cobalt Gray Equivalent) at 1.8–2.0 CGE per fraction. Patients were evaluated for response to therapy and treatment-related toxicity. Results: The overall clinical disease-free survival rate was 89% at 5 years. When post-treatment prostate-specific antigen (PSA) was used as an endpoint for disease control, the 4.5-year disease-free survival rate was 100% for patients with an initial PSA of 20.0, respectively. Patients in whom the post-treatment PSA nadir was below 0.5 ng/ml did significantly better than those whose nadir values were between 0.51–1.0 or > 1.0 ng/ml: the corresponding 5-year disease-free survival rates were 91%, 79%, and 40%, respectively. Minimal radiation proctitis was seen in 21% of patients; toxicity of greater severity was seen in less than 1%. Conclusion: Proton therapy to 74–75 CGE produced minimal treatment-related toxicity and excellent PSA normalization and disease-free survival in patients with low initial PSA levels. A prospective randomized dose-escalation trial is now underway to help define the optimum dose of radiation for patients with early stage prostate cancer.

Beam intensity modulation for penumbra enhancement in the treatment of lung cancer

Purpose: A treatment planning study was performed for patients with lung cancer in order to investigate the extent to which doses to critical structures could be reduced by penumbra enhancement at the superior and inferior field edges, using beam intensity modulation (BIM) with a multileaf collimator. By applying two independent published models for the prediction of the incidence of normal tissue complications, the potential for dose escalation without increasing the incidence of pneumonitis was estimated. Methods and Materials: For 12 patients, the standard treatment technique was compared with the BIM technique using the Cadplan 3D planning system (Varian-Dosetek). Dose distributions in the healthy lung tissue were evaluated by considering both lungs minus the tumor as one functional unit. The following parameters were compared: (i) the average normalized total dose (NTD), (ii) the lung volume receiving an NTD of more than 20 Gy, and (iii) the calculated normal tissue complication probability (NTCP). Results: Due to the applied BIM technique, the field lengths could be reduced by 1.4 cm for all patients, while achieving a minimum dose at the superior and inferior parts of the target of 95% of the isocenter dose. Compared to the standard technique, BIM reduced the patient mean of the average NTD for the healthy lung tissue from 16.5 to 15.3 Gy. The volume of healthy lung tissue receiving an NTD of 20 Gy or more was reduced by 9.7% (range 2.2 to 23.1%). The calculated NTCP reduced from 10.7% to 7.6% on average. The length of the esophagus that received a dose of 60 Gy or more could be reduced for 5 of the 6 stage III patients in this study. Based on equal lung NTCPs for the standard technique and the BIM technique, a mean dose escalation of 5.7 Gy (range 1.1 to 16.0 Gy) was possible for the 12 patients in this study. Based on equal average NTDs for the two techniques, the patient mean of the allowed dose escalation was 6.5 Gy (range 1.1 to 18.2 Gy). All dose escalations would be possible without exceeding the spinal cord tolerance dose. Conclusions: The BIM technique reduced the dose delivery to critical tissues. Two published methods for estimating the incidence of pneumonitis both pointed to a potential for dose escalation of 6 to 7 Gy on average with the BIM technique, without increasing the incidence of pneumonitis. For 2 of the 12 patients in this study the estimated allowed dose escalation even exceeded 15 Gy.

Acute morbidity reduction using 3DCRT for prostate carcinoma: a randomized study

Purpose: To study the effects on gastrointestinal and urological acute morbidity, a randomized toxicity study, comparing conventional and three-dimensional conformal radiotherapy (3DCRT) for prostate carcinoma was performed. To reveal possible volume effects, related to the observed toxicity, dose–volume histograms (DVHs) were used.Methods and Materials: From June 1994 to March 1996, 266 patients with prostate carcinoma, stage T1-4N0M0 were enrolled in the study. All patients were treated to a dose of 66 Gy (ICRU), using the same planning procedure, treatment technique, linear accelerator, and portal imaging procedure. However, patients in the conventional treatment arm were treated with rectangular, open fields, whereas conformal radiotherapy was performed with conformally shaped fields using a multileaf collimator. All treatment plans were made with a 3D planning system. The planning target volume (PTV) was defined to be the gross target volume (GTV) + 15 mm. Acute toxicity was evaluated using the EORTC/RTOG morbidity scoring system.Results: Patient and tumor characteristics were equally distributed between both study groups. The maximum toxicity was 57% grade 1 and 26% grade 2 gastrointestinal toxicity; 47% grade 1, 17% grade 2, and 2% grade > 2 urological toxicity. Comparing both study arms, a reduction in gastrointestinal toxicity was observed (32% and 19% grade 2 toxicity for conformal and conventional radiotherapy, respectively; p = 0.02). Further analysis revealed a marked reduction in medication for anal symptoms: this accounts for a large part of the statistical difference in gastrointestinal toxicity (18% vs. 14% [p = ns] grade 2 rectum/sigmoid toxicity and 16% vs. 8% [p < 0.0001] grade 2 anal toxicity for conventional and conformal radiotherapy, respectively). A strong correlation between exposure of the anus and anal toxicity was found, which explained the difference in anal toxicity between both study arms. No difference in urological toxicity between both treatment arms was found, despite a relatively large difference in bladder DVHs.Conclusions: The reduction in gastrointestinal morbidity was mainly accounted for by reduced toxicity for anal symptoms using 3DCRT. The study did not show a statistically significant reduction in acute rectum/sigmoid and bladder toxicity.

Virtual planning of liver resections: image processing, visualization and volumetric evaluation

Operability of a liver tumor depends on its three dimensional relation to the intrahepatic vascular trees as well as the volume ratio of healthy to tumorous tissue. Precise operation planning is complicated by anatomic variability and distortion of the vascular trees by the tumor or preceding liver resections. We have developed a computer based 3D virtual operation planning system which is ready to go in routine use. The main task of a system in this domain is a quantifiable patient selection by exact prediction of post-operative liver function. It provides the means to measure absolute and relative volumes of the organ structures and resected parenchyma. Another important step in the pre-operative phase is to visualize the relation between the tumor, the liver and the vessel trees for each patient. The new 3D operation planning system offers quantifiable liver resection proposals based on individualized liver anatomy. The results are presented as 3D movies or as interactive visualizations as well as in quantitative reports.

Conformal proton therapy for prostate carcinoma

Background: The role and optimum dose of radiation to eradicate prostate cancer continues to be evaluated. Protons offer an opportunity to increase the radiation dose to the prostate while minimizing treatment toxicity.Methods: Six hundred forty-three patients with localized prostate cancer were treated with protons, with or without photons. Treatments were planned with a 3D planning system; patients received 74–75 CGE (Cobalt Gray Equivalent) at 1.8–2.0 CGE per fraction. Patients were evaluated for response to therapy and treatment-related toxicity.Results: The overall clinical disease-free survival rate was 89% at 5 years. When post-treatment prostate-specific antigen (PSA) was used as an endpoint for disease control, the 4.5-year disease-free survival rate was 100% for patients with an initial PSA of < 4.0 ng/ml, and 89%, 72%, and 53% for patients with initial PSA levels of 4.1–10.0, 10.1–20.0, and > 20.0, respectively. Patients in whom the post-treatment PSA nadir was below 0.5 ng/ml did significantly better than those whose nadir values were between 0.51–1.0 or > 1.0 ng/ml: the corresponding 5-year disease-free survival rates were 91%, 79%, and 40%, respectively. Minimal radiation proctitis was seen in 21% of patients; toxicity of greater severity was seen in less than 1%.Conclusion: Proton therapy to 74–75 CGE produced minimal treatment-related toxicity and excellent PSA normalization and disease-free survival in patients with low initial PSA levels. A prospective randomized dose-escalation trial is now underway to help define the optimum dose of radiation for patients with early stage prostate cancer.

Analysis of different application systems and CT-controlled planning variants in treatment of primary endometrial carcinomas. Is brachytherapy treatment of the entire uterus technically possible?

Intracorporal brachytherapy is regarded as the definitive component of treatment for inoperable patients with endometrial carcinoma. Until now the whole uterus has been claimed to represent the target volume independent of individual tumor spread. The purpose of this work is to analyse the correlation between target volume and treated volume using different application- and planning procedures. In a consecutive series of 10 patients with primary irradiated endometrial carcinoma we analyzed the correlation between target volume and treated volume using either standard 1-channel applicators or individual Heyman-applicators. Application of the ovoids was followed by a planning CT scan for all patients. Based on this, target volume (uterus volume) was estimated on a 3D-planning system. According to the measurable length of the uterus cavity we determined the corresponding standard 1-channel applicator and calculated the respectively treated volume. Estimating the advantages of an optimized treatment planning strategy for individual Heyman-applications were compared the treated volumes, which result from a standardized and optimized treatment planning procedure. The mean uterus volume was 180 cm3 (range 57 to 316 cm3). Asymmetric uterus configurations with longitudinal or sagittal side differences exceeding 1 cm were found in 40% of the cases. Using standard 1-channel applicators on average 47% (range 25 to 89%) of the uterus volume were enclosed by the treated volume compared to 70% for Heyman-applications. Differentiating these individual applications according to the variable treatment modality values of mean 66% (range 36 to 110%) for the standardized and 73% (range 48 to 95%) for the optimized treatment planning strategy were found. Moreover optimized planning modalities led to an improved coverage of the target volume in 5 out of 10 cases with an increase in volume of 20% on average (range 11 to 32%). In 3 cases changes of less than 5% were noticed (no improvement). In order to protect organs at risk treated volume had to be decreased in 2 cases for 19% and 40% respectively. Intracavitary brachytherapy of primary endometrial carcinoma was improved by individualized application- and planning procedures, which led to better adaptations of the treated volumes to the target volumes. Nevertheless a complete coverage--corresponding to the primary intent--was not possible. Individualized and optimized brachy-therapy must be performed according to the individual tumor spread and uterus configuration. Therefore, different applicators are required.

Non-coplanar beam intensity modulation allows large dose escalation in stage III lung cancer

Purpose: To evaluate the feasibility of dose escalation in stage III non-small cell lung cancer, we compared standard coplanar (2D) with non-coplanar beam arrangements, without (3D) and with beam intensity modulation (3D-BIM). Materials and methods: This study was a planning effort performed on a non-selected group of 10 patients. Starting from a serial CT scan, treatment planning was performed using Sherouse's GRATIS™ 3D planning system. Two target volumes were defined; gross tumor volume (GTV) defined a high-dose target volume that had to receive a dose of at least 80 Gy and GTV plus the lymph node regions with >10% probability of invasion defined an intermediate-dose target volume (GTV+N). It was our intention to irradiate GTV+N up to 56 Gy or more. If the prescribed doses on GTV and GTV+N could not be reached with either the 2D or 3D technique, a 3D-BIM plan was performed. The 3D-BIM plan was a class solution involving identical gantry angles, segment arrangements and relative segment weights for all patients. Dose volume histograms for GTV, GTV+N, lung and spinal cord were calculated. Criteria for tolerance were met if no points inside the spinal cord exceeded 50 Gy and if at least 50% of the lung volume received less than 20 Gy. Under these constraints, maximal achievable doses to GTV and GTV+N were calculated. Results: In all 2D plans, spinal cord was the limiting factor and the prescribed doses for GTV and GTV+N could not be reached in any patient. The non-coplanar 3D plan resulted in a satisfying solution in 4 out of 10 patients under the same constraints. In comparison with 2D, the minimum dose in GTV+N was increased. Six patients had to be planned with the 3D-BIM technique. The theoretical minimum dose to GTV+N ranged between 56 and 98 Gy. The delivery of 80 Gy or more to GTV was possible in all patients. For a minimal dose of 80 Gy to GTV, the maximal dose to any point of the spinal cord varied between 27 and 46 Gy. The lung volume receiving more than 20 Gy ranged from 26 to 46%. Conclusion: The potential of 3D-BIM for dose escalation is explained as follows: (i) compared to other planning techniques, a larger amount of lung tissue can be spared by using beam directions that are well-aligned with the mediastinal structures. Such beam directions have narrow angles with the sagittal plane; (ii) dividing all beams into segments with well-specified geometrical restrictions in relation to the spinal cord and well-defined relative weights results in a lower dose to the spinal cord.

Field margin reduction using intensity-modulated x-ray beams formed with a multileaf collimator

Purpose : In axial, coplanar treatments with multiple fields, the superior and inferior ends of a planning target volume (PTC) are at risk to get underdosed due to the overlapping penumbras of all treatment fields. We have investigated a technique using intensity modulated x-ray beams that allows the use of small margins for definition of the superior and inferior field borders while still reaching a minimum PTV-dose of 95% of the isocenter dose. Methods and Materials : The applied intensity modulated beams, generated with a multileaf collimator, include narrow (1.1-1.6 cm) boost fields to increase the dose in the superior and inferior ends of the PTV. The benefits of this technique have been assessed using 3D treatment plans for 10 prostate cancer patients. Treatment planning was performed with the Cadplan 3D planning system (Varian-Dosetek). Dose calculations for the narrow boost fields have been compared with measurements. The applications of the boost fields has been tested on the MM50 Racetrack Microtron (Scanditronix Medical AB), which allows fully computer-controlled setup of all involved treatment fields. Results : Compared to our standard technique, the superior-inferior field length can be reduced by 1.6 cm, generally yielding smaller volumes of rectum and bladder in the high dose region. For the narrow boost fields, calculated relative dose distributions agree within 2% or 0.2 cm with measured dose distributions. For accurate monitor unit calculations, the phantom scatter table used in the Cadplan system had to be modified using measured data for square fields smaller than 4 × 4 cm 2. The extra time needed at the MM50 for the setup and delivery of the boost fields in usually about 1 min. Conclusion : The proposed use of intensity modulated beams yields improved conformal dose distributions for treatment of prostate cancer patients with a superior-inferior field size reduction of 1.6 cm. Treatments of other tumor sites can also benefit from the application of the boost fields.

Dose estimation to critical organs from vertex field treatment of brain tumors

Radiation management of intracranial tumors may require a noncoplanar vertex field that often irradiates the entire length of the body. In view of radiation related risks to the normal tissues dose estimation to the extracranial organs such as the thyroid gland, spinal cord, heart, and genitalia is performed for a vertex field. A vertex field used clinically was reproduced on an anthropomorphic Rando phantom to measure radiation dose to various organs in the primary beam. Three photon beams (4, 6, and 10 MV), and two high energy electron beams (16 and 20 MeV) were used. Dosimetry was performed with an ion chamber sandwiched between phantom slices at the appropriate positions. All doses were normalized to the target dose at a depth of 5 cm. The effect of the head position was studied by rotating the gantry angle up to +/-20 degrees to mimic the extension and flexion of the head. Theoretical calculation was performed using an exponential best fit to the depth dose table to estimate the dose to various points and compare with the measured dose. The measured normalized dose to the cervical cord, thyroid, heart, and female and male gonads are 60, 36, 16, 2.5, and 1.6%, respectively, for a 6 MV photon beam. The dose from 4 MV and 10 MV are slightly lower and higher, respectively. Doses from electron beams are about a factor of 4-10 lower than those of the photon beams. The measured gonadal dose from the primary beam is <5% of the target dose for all energies used in the study. The actual value, however, is dependent on the body structure, length, and the posture of the patient. A +5 degree head flexion had little effect on the dose to the various parts of the body. The head rotations greater than +/-10 degrees produced relatively lower doses by a factor of 10(-2) to the organs at distances greater than 40 cm from the prescription point. The radiation doses to the different critical organs estimated from the fitted curves are lower than the measured doses up to 35%. When a vertex field is used for the treatment of the brain tumors, the entire axial length of the body is irradiated which adds to the integral dose. Unlike the scattered and leakage radiation, the primary dose to extracranial critical organs is greater for higher energies. For a 10 MV beam the ovary and testis at a distance of 80 cm and 90 cm may receive a dose of 4.2 and 3%, respectively, of the target dose. The gonadal dose could be quite significant if the entire treatment is delivered using a vertex field. For pediatric and smaller patients, dose to the critical organs at known distances could be estimated from the empirical equation obtained from the measured data. While the risk-benefit ratio is often evaluated and acceptable for treating malignant tumors, the long-term complications need thorough assessment in younger and curable patients. In view of radiation carcinogenesis and genetic burden, dose reduction to critical organs should be considered using a 3D planning system to arrange beams in other nonaxial planes and by considering electron beams for the vertex field.

Simulation by a diagnostic CT for the early vocal cord carcinoma

The CT-based simulation with a 3D planning system permits the optimization of radiotherapy treatments. The goal is to obtain an increase in the local control and survival with a reduction of the treatment related toxicity. In our hospital, we do not have a CT simulator and our 3D planning system is not yet working, therefore, we have developed a system to simulate radiotherapy treatments using a diagnostic CT. We began by simulating an early vocal cord carcinoma. The rules of this simulation are presented using a clinical case as an example.

A method to study the characteristics of 3D dose distributions created by superposition of many intensity-modulated beams delivered via a slit aperture with multiple absorbing vanes

Highly conformal dose distributions can be created by the superposition of many radiation fields from different directions, each with its intensity spatially modulated by the method known as tomotherapy. At the planning stage, the intensity of radiation of each beam element (or bixel) is determined by working out the effect of superposing the radiation through all bixels with the elemental dose distribution specified as that from a single bixel with all its neighbours closed (the `independent-vane' (IV) model). However, at treatment-delivery stage, neighbouring bixels may not be closed. Instead the slit beam is delivered with parts of the beam closed for different periods of time to create the intensity modulation. As a result, the 3D dose distribution actually delivered will differ from that determined at the planning stage if the elemental beams do not obey the superposition principle. The purpose of this paper is to present a method to investigate and quantify the relation between planned and delivered 3D dose distributions. Two modes of inverse planning have been performed: (i) with a fit to the measured elemental dose distribution and (ii) with a `stretched fit' obeying the superposition principle as in the PEACOCK 3D planning system. The actual delivery has been modelled as a series of component deliveries (CDs). The algorithm for determining the component intensities and the appropriate collimation conditions is specified. The elemental beam from the NOMOS MIMiC collimator is too narrow to obey the superposition principle although it can be `stretched' and fitted to a superposition function. Hence there are differences between the IV plans made using modes (i) and (ii) and the raw and the stretched elemental beam, and also differences with CD delivery. This study shows that the differences between IV and CD dose distributions are smaller for mode (ii) inverse planning than for mode (i), somewhat justifying the way planning is done within PEACOCK. Using a stretched elemental beam is a useful adjustment to improve the accuracy of inverse planning but the 3D dose distribution actually delivered will display characteristics of the collimation.

Prism: A new approach to radiotherapy planning software

We describe the capabilities and performance of Prism, an innovative new radiotherapy planning system with unusual features and design. The design and implementation strategies are intended to assure high quality and clinical acceptability. The features include Artificial Intelligence tools and special support for multileaf collimator (MLC) systems. The design provides unusual flexibility of operation and ease of expansion. We have implemented Prism, a three-dimensional (3D) radiotherapy treatment-planning system on standard commercial workstations with the widely available X window system. The design and implementation use ideas taken from recent software engineering research, for example, the use of behavioral entity-relationship modeling and the "Mediator Method" instead of ad-hoc programming. The Prism system includes the usual features of a 3D planning system, including Beam's Eye View and the ability to simulate any treatment geometry possible with any standard radiotherapy accelerator. It includes a rule-based expert system for automated generation of the planning target volume as defined in ICRU Report 50. In addition, it provides special support for planning treatments with a multileaf collimator (MLC). We also implemented a Radiotherapy Treatment Planning Tools Foundation for Prism, so that we are able to use software tools form other institutions without any source code modification. The Prism system has been in clinical operation at the University of Washington since July 1994 and has been installed at several other clinics. The system is run simultaneously by several users, each with their own workstation operating from a common networked database and software. In addition to the dosimetrists, the system is used by radiation oncologists to define tumor and target volumes and by radiation therapists to select treatment setups to load into a computer controlled accelerator. Experience with the installation and operation has shown the design to be effective as both a clinical and research tool. Integration of software tools has eased the development and significantly enhanced the clinical usability of the system. The design has been shown to be a sound basis for further innovation in radiation treatment planning software and for research in the treatment planning process.

Planning and delivering high doses to targets surrounding the spinal cord at the lower neck and upper mediastinal levels: static beam-segmentation technique executed with a multileaf collimator

Background and purpose. It remains a technical challenge to limit the dose to the spinal cord below tolerance if, in head and neck or thyroid cancer, the planning target volume reaches to a level below the shoulders. In order to avoid these dose limitations, we developed a standard plan involving Beam Intensity Modulation (BIM) executed by a static technique of beam segmentation. In this standard plan, many machine parameters (gantry angles, couch position, relative beam and segment weights) as well as the beam segmentation rules were identical for all patients. Materials and methods. The standard plan involved: the use of static beams with a single isocenter; BIM by field segmentation executable with a standard Philips multileaf collimator; virtual simulation and dose computation on a general 3D-planning system (Sherouse's GRATIS®); heuristic computation of segment intensities and optimization (improving the dose distribution and reducing the execution time) by human intelligence. The standard plan used 20 segments spread over 8 gantry angles plus 2 non-segmented wedged beams (2 gantry angles). Results. The dose that could be achieved at the lowest target voxel, without exceeding tolerance of the spinal cord (50 Gy at highest voxel) was 70–80 Gy. The in-target 3D dose-inhomogeneity was ≈25%. The shortest time of execution of a treatment (22 segments) on a patient (unpublished) was 25 min. Conclusions. A heuristic model has been developed and investigated to obtain a 3D concave dose distribution applicable to irradiate targets in the lower neck and upper mediastinal regions. The technique spares efficiently the spinal cord and allows the delivery of higher target doses than with conventional techniques. It can be planned as a standard plan using conventional 3D-planning technology. The routine clinical implementation is performed with commercially available equipment, however, at the expense of extended execution times.

Prostate volumes defined by magnetic resonance imaging and computerized tomographic scans for three-dimensional conformal radiotherapy

Purpose: To compare the prostate volumes defined on magnetic resonance imaging (MRI), and noncontrast computerized tomographic (CT) scans used for three-dimensional (3D) treatment planning. Methods and Materials : Ten patients simulated for treatment using immobilization and a retrograde urethrogram. 3D images were used to compare prostate volumes defined by MRI (4–6 mm thick slices) and CT images (5 mm thick slices). Prostate volumes were calculated in cm 3 using the Scanditronix 3D planning system. MRI/CT images were merged using bony anatomy to define the regions of discrepancy om prostate volumes. Results : The mean prostate volume was 32% larger (range −5–63%) when defined by noncontrast CT compared to MRI. The areas of nonagreement tended to occur in four distinct regions of discrepancy: (a) the posterior portion of the prostate, (b) the posterior-inferior-apical portion of the prostate, (c) the apex due to diasgreement between a urothrogram based definition and the location defined by MRL, (d) regions corresponding to the neurovascular bundle. Conclusion : There is a tendency to overestimate the prostate volume by noncontrast CT compared to MRI. Awareness of this tendency should allow us to be to more accurately define the prostate during 3-D treatment planning.

431CT-based simulation to optimize radiotherapy for head and neck cancer in centers without CT simulator and 3D planning systems

431CT-based simulation to optimize radiotherapy for head and neck cancer in centers without CT simulator and 3D planning systems

207 Extension of Sherouse's GRATIS™ three-dimensional treatment planning system for use with a multileaf collimator

In February 1995, a linear accelerator (Philips SL25) was retrofitted with a Philips multileaf collimator (MLC). MLC reduces workload (decreases the numbers of cerrobend blocks) and increases throughput (avoids tray placements). However, programming the leaf settings is a labur intensive procedure on the Philips MLC, as settings have to be derived manually from simulator films. We use the GRATIS 3D planning system by George W. Sherouse and have written an extension to plan the leaf settings in beam's eye view mode. From a tool implemented in GRATIS' last release, which draws a conformal block around the target with a predefined margin, we developed a feature for automatic or interactive leaf setting. After virtual simulation, a file with the leaf settings is transferred to the MLC computer over a local network. The advantages of this system are efficiency, automatization and elimination of transfer errors. Within the philosophy of GRATIS, we will make our tool freely available to the GRATIS users.

432 Matching half beams in head and neck radiotherapy. planning and dosimetry

<h3>Introduction</h3> In the treatment planning of the head and neck tumours, usually matching fields are necessary. There are inherent hazards with this technique in that overlapping of these portals may result in hot and cold spots at the field edges. The use of linacs with independent collimators enables to eliminate the beam divergency, matching then the central axes of adjacent fields where there is no divergence. On the other hand, the 3D radiation treatment planning systems allow us to calculate the dose variation through the field's junction. <h3>Technical description</h3> We describe a technique consistent in three isocentric half-fields (two upper laterals and one lower anterior). Patients are immobilized with a thermoplastic mask. The upper limit of the lateral fields and the midline are outlined in the mask. It's not necessary to move either the patient or the treatment couch for the different fields of treatment. The SSD for each field is calculated at simulation and/or planihcation time. The lateral fields are shielded with individual focalized Cerrobend's blocks, leaving the half field limit free. <h3>Conclusion</h3> In this technique there isn't beam divergency at the junction's fields, so the homogeneity is maximal. A dosimetric study with a 3D planning system shows a good distribution of dose. The dose contribution of each half field in the other half field is <2%. The new linacs working with asymmetric collimators enable us to use the split matching technique in a simple, reproducible and accurate form.

231 - Conformal static field irradiation of localized prostatic cancer without 3D planning system

231 - Conformal static field irradiation of localized prostatic cancer without 3D planning system