Ultra-thin occlusal veneers bonded to enamel and made of ceramic or hybrid materials exhibit load-bearing capacities not different from conventional restorations

Abstract

ObjectivesThe objective of this study was to test whether or not the load-bearing capacity of occlusal veneers bonded to enamel and made of ceramic or hybrid materials does differ from those of porcelain-fused-to-metal or lithium disilicate glass ceramic crowns. Material and methodsIn 80 human molars occlusal enamel was removed without extending into the dentin in order to mimic substance defects caused by attrition. The restorations were digitally designed at a standardized thickness of either 0.5 mm or 1.0 mm. For each thickness, 4 test groups were formed each including a different restorative material: “0.5-ZIR”: 0.5 mm thick zirconia (Vita YZ HT); “1.0-ZIR”: 1.0 mm thick zirconia (Vita YZ HT); “0.5-LDC”: 0.5 mm thick lithium disilicate ceramic (IPS e.max Press); “1.0-LDC”: 1.0 mm thick lithium disilicate ceramic (IPS e.max Press); “0.5-HYC”: 0.5 mm thick PICN (Vita Enamic); “1.0-HYC”: 1.0 mm thick PICN (Vita Enamic); “0.5-COC”: 0.5 mm thick tooth shaded resin composite (Lava Ultimate) and “1.0-COC”: 1.0 mm thick tooth shaded resin composite (Lava ultimate). Each group consists of 10 specimens. Two additional groups of 10 specimens each were used as controls and exhibited conventional crown preparations. In one group the crowns were made of lithium-disilicate ceramic (“CLD”: IPS e.max CAD) and the other group consisted of porcelain-fused to metal crowns (“PFM”). All restorations were cemented onto the prepared teeth following the manufacturer's instruction of the corresponding luting cement. Subsequently, they were thermo-mechanically aged and then loaded until fracture. Load-bearing capacities (Fmax) between the groups were compared applying the Kruskal-Wallis test (p < 0.05) and pairwise group comparisons using the Dunn's method. ResultsMedian values (and quartiles) for the load-bearing capacity amounted to (Fmax) 2′407 (1′670; 2′490) N for the CLD group and to 2′033 (1′869; 2′445) N for the PFM group. For the 0.5 mm thick restorations Fmax reached the highest median value in group 0.5-HYC 2′390 (1′355; 2′490) N, followed by 0.5-COC 2′200 (1′217; 2′492) N and 0.5-LDC 1′692 (1′324; 2′355) N. No results were obtained for group 0.5-ZIR due to the impracticability to fabricate ultra-thin specimens. The distribution of the values for the 1.0 mm thick restorations was 2′489 (2′426; 2′491) N for 1.0-COC, 2′299 (2′156; 2′490) N for 1.0-ZIR, 2′124 (1′245; 2′491) N for 1.0-HYC, and 1′537 (1′245; 1′783) N for 1.0-LDC. The differences of the medians between the test and the control groups did not reach statistical significance for the 0.5 mm thick specimens (KW: p = 0.6952 and p = 0.6986). Within the groups exhibiting 1.0 mm thickness, however, significant different medians were found: 1.0-LDC < 1.0-ZIR and 1.0-LDC < 1.0-COC (KW: p < 0.0209). ConclusionsRegarding their maximum load-bearing capacity, minimally invasive occlusal veneers made of ceramic and hybrid materials can be applied to correct occlusal tooth wear and thus replace conventional crown restorations.