The effect of uniform heating on the biomechanical properties of the intervertebral disc in a porcine model

Abstract

Background context The use of minimally invasive lumbar intradiscal heating techniques, including intradiscal electro-thermal therapy (IDET), endoscopic radio-frequency annuloplasty, nucleoplasty and laser discectomy, for chronic lumbar discogenic pain and contained disc herniation has recently gained popularity. The purported therapeutic mechanisms of these interventions include subtotal nuclectomy, annular nociceptor ablation, and stabilization of the annular fibers. Basic science data elucidating the biomechanical and histomorphologic alterations of heat treatments on disc remain sparse. Purpose The purpose of this study is to examine the effects of uniform heating on biomechanical properties and histomorphology of intervertebral disc tissues using a porcine model. Study design/setting In a laboratory setting, porcine functional spinal units consisting of vertebra-nucleus pulposus-vertebra core and porcine hamstring tendons were harvested. Studies were performed on these tissue samples by uniformly heating the specimens in a constant temperature water bath. Ten porcine lumbar disc core and twenty-five porcine hamstring tendons were utilized as the subjects for this study. The effects of uniform heat treatments on disc core and hamstring tendon were measured for shrinkage, stiffness, and load to failure strength. Histomorphological study was also carried on the same specimen. Methods The porcine vertebra-nucleus pulposus-vertebra segments were cored to a uniform 1-cm diameter. The hamstring tendons were cut to uniform 1.2-inch lengths. The tendon specimens were divided into groups of five each and heated in constant temperature water baths of 60°C, 65°C, 70°C, or 75°C for 10 min. Unheated specimens served as controls. The disc core specimens were divided in two group of five each, and tested at room temperature or after immersion in a 70°C bath. The shrinkage was monitored during immersion in the water bath. Biomechanical testing to failure was carried out using mechanical loading on an MTS servohydraulic testing machine operating under stroke control. Strength and stiffness of the tissue was determined. Histomorphology was studied by staining the specimen with hematoxylin and eosin (H&E), and examined under 200 times magnification. Non-heated controls were used for comparisons. Results The porcine hamstring tendons had no measurable shrinkage in specimens heated up to 65°C. At temperatures above 65°C, the shrinkage was concluded within 2 min of immersion and 70°C appeared to be the optimal temperature, as temperatures higher than this did not demonstrate incremental effects. The disc core samples were heated to 70°C (optimum temperature), and there appeared to be gross contraction of the disc core circumference to visual inspection, but no measurable lengthwise shrinkage could be appreciated. Histologically, the specimens demonstrated progressive loss of individual collagen fiber outline as the temperature increased. In the tendons, at 75°C all of the fibers appear to be fused together, and the voids between individual collagen fibers were no longer present. Biomechanical testing revealed that the tendons undergo a substantial reduction in stiffness after heating. The mean tendon stiffness for the unheated specimens was 19,356 psi, while the corresponding value for the heated tendons was 1023 psi. These were significantly different using the paired t-test at p=0.0043. For the disc core samples, there was no significant difference in either stiffness (p=0.182) or failure strength (p=0.998) after heating. All failures occurred in mid-substance of the specimen. Conclusions The application of uniform heating to nucleus pulposus disc core caused visible contraction of its circumference but not lengthwise shrinkage. The same heating shrinks the hamstring tendon and reduces its stiffness. Ultimate failure strength of the disc core specimen remains unchanged. The failure data was not obtainable for the tendon due to premature slippage from the fixation apparatus before failure. The results of this study fail to support a biomechanical justification for the application of uniform heat treatment to the whole intervertebral disc. Heating annulus fibrosus and nucleus pulposus separately to specific temperatures may have potential clinical benefits.