Abstract

Malachite green (MG) and its metabolite, leucomalachite green (LMG), exert toxic effects on the human body. The use of these dyes is illegal, but they are still detected in aquatic products. Freshwater fish are aquatic products with the high non-qualified rates. Therefore, the sensitive screening of MG and LMG in freshwater fish is of great importance to ensure the safety of aquatic products. Owing to the low contents of MG and LMG in fish and the complex matrix of actual samples, sample preparation is required before detection to purify impurities and enrich the target compounds. Graphite carbon nitride (GCN), a polymer material composed of C, N, and H, has good chemical and thermal stability, a large specific surface area, and a large number of active sites. It has a wide range of application prospects in adsorption and can be used in food safety testing when compounded with Fe3O4 to form magnetic graphite carbon nitride (MGCN). In this study, sulfonated magnetic graphite carbon nitride (S-MGCN) was prepared by further functionalizing MGCN with sulfonic acid. After characterization by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and vibrating sample magnetometry (VSM), a magnetic solid-phase extraction (MSPE) method based on S-MGCN was established to extract MG and LMG from freshwater fish. The targets were screened using ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). Following sulfonic acid functionalization, S-MGCN showed increased electrostatic interactions based on the MGCN adsorption mechanism, which includes hydrogen bonds and π-π interactions; thus, its adsorption efficiency was significantly improved. The matrix effects were -42.21% and -33.77% before functionalization, -11.40% and -7.84% after functionalization, thus confirming that S-MGCN has significant matrix removal ability. Given that S-MGCN demonstrated excellent efficiency as an MSPE adsorbent, the adsorption conditions for S-MGCN were optimized. The optimal conditions were as follows: adsorbent dosage, 15 mg; adsorption time, 2 min; solution pH, 5; and ionic strength, not adjusted. Under these conditions, the adsorption efficiency of S-MGCN could reach 94.2%. Different organic solvents were used to elute adsorbed MG and LMG, and the desorption efficiency peaked when 1%(v/v) ammonia acetonitrile was used as the elution solvent. The elution volume was also optimized, and a maximum desorption efficiency of 93.2% was obtained when 1 mL of 1%(v/v) ammonia acetonitrile was added to S-MGCN. The limits of detection (LODs) and quantification (LOQs) of the two targets were determined at signal-to-noise ratios (S/N) of 3 and 10, respectively. The LODs and LOQs were 0.075 μg/kg and 0.25 μg/kg, respectively. The linear ranges of the two target compounds were 0.25-20.0 μg/kg with correlation coefficients (r) greater than 0.998. To assess accuracy and precision, we prepared spiked samples at three levels (low, medium, and high) with six parallel samples per level (n=6). The recoveries ranged from 88.8% to 105.9%. The intra- and inter-day relative standard deviations were 5.4%-13.7% (n=6) and 3.3%-11.1% (n=3), respectively. Compared with the national standard method, the proposed method features simpler sample pretreatment procedures, less use of organic reagents (5 mL), and a shorter extraction time (2 min); moreover, the method does not require complicated elution steps, and the eluent can be directly analyzed by UPLC-MS/MS. The test results of actual samples were consistent with those obtained via the national standard method, thus confirming the practical feasibility of the developed method. The proposed MSPE method based on S-MGCN is an efficient and environmentally friendly method that could provide a new methodological reference for the sensitive screening of MG and LMG in actual samples.

Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call