Photochemically-activated electrodes: application in design of reversible immunosensors and antibody patterned interfaces

Abstract

Antigen monolayers assembled onto Au electrodes associated with a quartz crystal act as electrochemical or microgravimetric quartz-crystal-microbalance (QCM) sensing interfaces for the complementary antibody. Electrochemical analysis of the antibody (Ab) is based on the insulation of the antigen monolayer electrode by the associated Ab towards a redox probe in the electrolyte solution. Ferrocene-modified glucose oxidase (Fc-GOx) and glucose are employed as redox probes for the amperometric transduction of the Ab association to the electrode. Bioelectrocatalyzed oxidation of glucose provides an electrochemical route to amplify the antigen-Ab complex formation. Electrochemical analysis of the dinitrophenyl antibody, DNP-Ab, by a dinitrophenyl-lysine monolayer electrode is presented. QCM analysis of the Ab is based on the frequency changes of the quartz crystal resulting from the association of the Ab to the crystal assembly. This method is discussed with the analysis of the fluorescein antibody, Flc-Ab, using a fluorescein monolayer-modified quartz crystal. A novel method to tailor reversible immunosensor devices by the application of photoisomerizable antigen monolayers on electrodes is presented. The antigen is modified by photoactive units exhibiting reversible photoisomerizable properties. In one photoisomer state, the antigen exhibits affinity for the Ab and enables its electrochemical or QCM analysis. Photoisomerization to the complementary state perturbs the antigen structure and the monolayer lacks affinity for the Ab. This enables the washing-off of the Ab and the regeneration of the actively sensing interface by a second illumination process that restores the antigen monolayer-modified surface. This method is exemplified by the development of a reversible DNP-Ab sensing electrode. N-Mercaptobutyl dinitrospopyran was assembled as a photoisomerizable monolayer on a Au electrode. The dinitrospiropyran monolayer, SP-state, exhibits affinity for the DNP-Ab and enables the amperometric detection of the Ab using Fc-GOx and glucose as redox probe. The complementary photoisomerized protonated dinitromerocyanine monolayer, MRH +-state, lacks affinity for the DNP-Ab. By photoisomerization of the DNP-Ab associated with the SP-monolayer electrode to the MRH +-monolayer state, the DNP-Ab is washed-off, and by a second illumination process, the MRH +-monolayer is re-isomerized to the SP-monolayer assembly, which is the active interface for further analysis of the DNP-Ab. Cyclic amperometric detection of the DNP-Ab by the photoisomerizable dinitrospiropyran monolayer is demonstrated. The association of the DNP-Ab to the SP-monolayer electrode and the dissociation of the Ab from the MRH +-monolayer electrode are confirmed by QCM experiments using a dinitrospiropyran monolayer-modified quartz crystal. The insulating features of an antigen-Ab complex on a conductive surface and the photochemically controlled association of an antibody to a photoisomerizable monolayer assembled onto the surface were used to develop means for micropatterning of surfaces by the antibody. A dinitrospiropyran antigen monolayer was assembled onto conductive ITO glass. A DNP-Ab solution was used as ‘ink solution’ to pattern the surface. The Ab-pattern was imaged by electrochemical copper deposition onto the Ab-lacking surface domains. The dinitrospiropyran monolayer assembled onto ITO or Pyrex glass surfaces was employed as an active interface for the photolithographic patterning of the surface with the DNP-Ab. Irradiation of the dinitrospiropyran monolayer, SP-state, through a grid-mask generated surface domains of protonated dinitromerocyanine, MRH +-state, which lacks affinity for the DNP-Ab. The DNP-Ab covalently-linked to agarose beads (50 μm) was selectively associated to the SP-monolayer sites and the micro-pattern of the resulting antibody was imaged. Methods for employing this photolithographic patterning of DNP-Ab to generate microstructures of any biomaterial, and, specifically, neural networks, are discussed.