Penerapan Green Manufacturing pada IKM Dadi Mulyo

Abstract

AbstractIKM Dadi Mulyo produces wood sawdust waste of approximately 400kg/day which if left for days on end will accumulate more and pollute the company's environment and the surrounding environment. Green Manufacturing method is used to perform analysis to reduce waste and increase added value. The research was conducted by direct observation and interviews. The results of the analysis show that the application of green manufacturing is able to reduce waste and increase added value by 50%. So that the increase in added value has the potential to improve the welfare of employees. Keywords: Waste, Green manufacturing, Value stream mapping, Future Stream Mapping, Value Added AbstrakIKM Dadi Mulyo menghasilkan limbah serbuk gergaji kayu kurang lebih 400 kg/hari yang apabila dibiarkan berhari-hari akan menjadi semakin menumpuk, mencemari lingkungan perusahaan dan lingkungan sekitar. Metode Green Manufacturing digunakan untuk melakukan analisis guna mengurangi pemborosan dan meningkatkan nilai tambah. Penelitian dilakukan dengan observasi langsung dan wawancara. Hasil analisis menunjukkan bahwa penerapan Green Manufacturing mampu mengurangi pemborosan dan meningkatkan nilai tambah sebesar 50%. Sehingga peningkatan nilai tambah berpotensi untuk meningkatkan kesejahteraan karyawan.Kata kunci: Waste, Green manufacturing, Value stream mapping, Future Stream Mapping, Value AddedReferensi[1] I. W. Sutarman, “Pemanfaatan Limbah Industri Pengolahan Kayu Di Kota Denpasar (Studi Kasus Pada Cv Aditya),” J. PASTI, vol. 10, no. 1, pp. 15–22, 2016.[2] Bahri S., “Pemanfaatan Limbah Industri Pengolahan kayu untuk pembuatan briket arang dalam mengurangi pencemaran lingkungan di Nangroe Aceh Darussalam,” J. Mek., vol. vol.4 no.2, pp. 410–415, 2007.[3] I. N. Tika, I. G. Ayu, T. Agustiana, D. Agus, and W. Erawan, “Pengolahan Limbah Serbuk Gergaji Kayu Menjadi Bata Akustik,” pp. 585–593, 2017.[4] I. Artikel, “Jurnal SENOPATI,” pp. 50–61, 2019.[5] U. Malik, “Jurusan Fisika Fakultas Matematika dan Imu Pengetahuan Alam Universitas Riau,” vol. I, no. 2, pp. 21–26, 1994.[6] P. O. Box and S. Lind, “Proceedings of the 2008 Winter Simulation Conference S. J. Mason, R. R. Hill, L. Mönch, O. Rose, T. Jefferson, J. W. Fowler eds.,” pp. 1922–1930, 2008.[7] C. B. Joung, J. Carrell, P. Sarkar, and S. C. Feng, “Categorization of indicators for sustainable manufacturing,” Ecol. Indic., vol. 24, pp. 148–157, 2013, doi: 10.1016/j.ecolind.2012.05.030.[8] T. Stock and G. Seliger, “Opportunities of Sustainable Manufacturing in Industry 4.0,” Procedia CIRP, vol. 40, no. Icc, pp. 536–541, 2016, doi: 10.1016/j.procir.2016.01.129.[9] S. Editor, Front Matter. 2014.[10] “13 Green Manufacturing.pdf.” .[11] A. M. Deif, “A system model for green manufacturing,” J. Clean. Prod., vol. 19, no. 14, pp. 1553–1559, 2011, doi: 10.1016/j.jclepro.2011.05.022.[12] W. Widada, “Reduce The Risk of Atherosclerosis through the wet Cupping Therapy,” J. Med. Sci. Clin. Res., vol. 6, no. 11, pp. 581–586, 2018, doi: 10.18535/jmscr/v6i11.102.[13] S. Sih, W. Wijayanti, and P. D. Sukmawati, “Potensi Limbah Serat Kayu Dari Pelepah Pisang Kering Sebagai Bahan Baku Pembuatan Frame Kacamata,” pp. 340–342.[14] S. Wardani, “Pemanfaatan Limbah Batu Bara ( Fly Ash ) Untuk Stabilitas Tanah Maupun Keperluan Teknik Sipil Lainnya Dalam Manggurangi Pencemaran Lingkungan,” Pengukuhan Guru Besar Fak. Tek. Univ. Diponogoro, pp. 1–71, 2008.