Abstract
This paper describes new mechanical and thermal processes which have been developed and verified to mitigate stress-corrosion cracking and corrosion-assisted fatigue in operating plants. These processes inhibit the initiation of cracks in as-fabricated components and piping systems. They can also prevent the further growth of cracks initiated before application of the process provided that the stresses can be kept below the threshold values for crack propagation. The processes introduce high residual compression, thus reducing the effective operating stresses which propagate existing defects or cracks. Both the mechanical and thermal processes described herein were conceived from basic theoretical considerations regarding the elastic-plastic behavior of pressure vessels, piping and structural materials. Due to small magnitudes of applied plastic strains, the metallurgical properties of the materials are not essentially altered by either process. Residual tensile stresses, which enhance crack initiation and propagation, are replaced by residual compressive stresses, which inhibit crack initiation and propagation. The Mechanical Stress Improvement Process (MSIP) has been used extensively to treat weldments in nuclear power plants. The process introduces a slight permanent contraction of the pipe nozzle, elbow or other component next to the circumferential weldments. The resulting plastic flow redistributes the residual as-welded stresses and generates beneficial compressive stresses at the inner pipe surface in the region of the weldment. The area of residual compression includes the weld metal and heat-affected zones, thus encompassing material which may be sensitized to stress-corrosion attack or metallurgical notch effects. MSIP introduces compressive stresses at weldments by mechanical means via a hydraulically actuated mechanical clamp used to contract the shell on one side of the weldment. The shell is squeezed by the tool in the near vicinity of the circumferential weldment but not at the weld itself. Contraction of the shell and the position and width of the tool are such that the plastic zone which is developed during application of the process extends throughout the weldment region. Compatibility of the deformation along the shell creates an axial profile which at the inner surface of the weldment has a concave curvature. The negative axial curvature and corresponding reduction of the pipe radius result in the generation of residual compressive stresses at the inner pipe surface in both the axial and hoop directions, respectively. This is quite beneficial where the coolant is corrosive and subjected to thermal transients. MSIP imposes only monotonic compressive plastic strains, and therefore does not propagate existing cracks. The process has been applied to plants with many years of prior service, including critical safety Class 1 weldments in nuclear plants known to contain existing cracks. Reinspection after a year of operation confirmed that the cracks did not grow. Variations in actual as-fabricated weldment strength due to variations in welding processes and parameters are known to be quite substantial. However, the tool design includes the use of spacers and shims which limit the maximum contraction, and the process is displacement-controlled. This makes it possible to set the process parameters to include wide variations in material strength, while achieving consistent results. The results of finite element analyses are presented for various geometries including applications near thermal sleeves, and transition weldments which include three or more materials. The Thermal Surface Improvement Process (TSIP) is applicable to virtually any size and shape of mechanical element, from pressure vessels to machine parts and turbine blades. The mechanical elements being treated are heated to an elevated temperature, and then the surface is rapidly cooled, such that the transient thermal stresses exceed the flow strength of the material in biaxial tension. This cooling is usually accomplished by short time, intensive spray quenching. When the entire mechanical part returns to uniform temperature, high residual compressive stresses are introduced at the surface of the part. The thickness of the surface layer which is in residual compression can be made substantially greater than the compressive layers that can be introduced by shot peening or other processes, and the mechanical integrity of the surface material is not disturbed. The applicability of the process is more limited for very high strength materials where higher temperatures are needed to achieve yielding during the quench phase. However, the elevated temperature must be limited to prevent undesirable metallurgical changes.
Talk to us
Join us for a 30 min session where you can share your feedback and ask us any queries you have
More From: International Journal of Pressure Vessels and Piping
Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.