INVESTIGATION THE OLIGOMERIZATION PROCESS OF HEXENE-1

Shahla Alizade,Aliyevfariz Ramik,Amirovfariz Ali,Ibragimovhikmet Jamal

doi:10.24297/jac.v14i1.6455

Shahla Alizade, Aliyevfariz Ramik + Show 2 more

Open Access

https://doi.org/10.24297/jac.v14i1.6455

Copy DOI

Abstract

In article for oligomerization and alkylation processes, to obtain a useful and highly stable active catalyst, New Catalytic Complex (NCC) synthesized which is based on aluminum metal using C2H4Cl2 and this complex has shown high stability in alkylation, oligomerization processes compared to other aluminum-containing catalysts. It is difficult to regulate the molecular mass distribution of received products during oligomerization, either Intensificate the oligomerization process of olefins that is why this process take place in presence of obtaining of bimetal catalytic complex with a highly stable activity from the modification of the New Catalytic Complex(NCC) with transition metal chloride. Comparatively studied oligomerization of Hexen-1 in present of new bimetallic catalytic complex which was modified by NCC and chromium salt (NCC/CrCl3), effect of temperature, reaction time, concentration of the catalyst and the proportion of catalyst components (Al:Cr) in the process was investigated.It was determined that at the initial time (10 min) conversion hexene-1 and the yield of purposeful oil fraction were low. Increasing time, conversion rate of Hexen-1 increases and the optimal time for the process is considered as 60 minutes. In low concentrations of catalyst (0,1-0,3) oligomerization of hexene-1 is low but in high concentrations(>1%) reaction goes with high rate, at optimal concentration 0,5% mass both the yield of oil fraction and its chemical-physical properties were high.In oligomerization process investigated ratio effect of catalyst components Al: Cr that was used Al: Cr=(4-32):1 mol.It has been revealed that oligomerization of Hexen-1, at low mol ratio of components (4:1), received yield of oligomer fraction decreases while mol ratio increases (16:1, 32:1).Studies determined that bimetallic complex at 8:1 mole has shown the maximal activity in oligomerization process of Hexen-1.The effect of the temperature on the oligomerization process was studied in the range of 30-60ÂºC, increasing the temperature up to 50 Â°C has a positive effect on the course of the process and despite providing complete oligomerization of hexene-1 its also providing increasing the amount of oil fractions with high viscosity. According to the researches, the optimal conditions for the oligomerization process of hexene-1 with the participation of the bimetallic catalytic complex: reaction time â€“ 60 min., concentration of catalyst â€“ 0,5 % by wt., mol ration of components Al:Cr = 8:1, temperature â€“ 50 Â°C. In known optimal condition its possible to obtain oligomers with physical indications, characterized by narrow molecular mass distribution, by new catalytic complex that was modified by chromium salt.Such products have special importance, as low-freezing, high viscosity index qualitative engine oils.Synthesis of bimetallic catalytic complexes, with their presence in oligomerization of olefins and fractions, opens wide range perspectives in synthesis of different high-molecular compounds in industry

Highlights

Technical progress prevents the friction of different mechanisms, increasing the role of lubricants, as the most important elements of the technique, that's why different requirements for their quality are emerged and increased
For oligomerization and alkylation processes, to obtain a useful and highly stable active catalyst, New Catalytic Complex (NCC) synthesized which is based on aluminum metal using C2H4Cl2 and this complex has shown high stability in alkylation, oligomerization processes compared to other aluminum-containing catalysts
In this article presented intensification of the oligomerization process of olefins, regulation of molecular mass distribution of received products during oligomerization in presence of NCC, which is based on obtaining of bimetal catalytic complex with a highly stable activity from the modification of the NCC with transition metal chloride

Summary

Introduction

Technical progress prevents the friction of different mechanisms, increasing the role of lubricants, as the most important elements of the technique, that's why different requirements for their quality are emerged and increased. It should be noted that processing of raw materials by modern methods allow to regulate physical and chemical properties of products at a wide range and improving new methods for the quality of oils. In this article presented intensification of the oligomerization process of olefins, regulation of molecular mass distribution of received products during oligomerization in presence of NCC, which is based on obtaining of bimetal catalytic complex with a highly stable activity from the modification of the NCC with transition metal chloride.

Results

Conclusion