Abstract

To meet the performance and scalability demands of the fast-paced technological growth towards exascale and big data processing with the performance bottleneck of conventional metal-based interconnects (wireline), alternative interconnect fabrics, such as inhomogeneous three-dimensional integrated network-on-chip (3D NoC) and hybrid wired-wireless network-on-chip (WiNoC), have emanated as a cost-effective solution for emerging system-on-chip (SoC) design. However, these interconnects trade off optimized performance for cost by restricting the number of area and power hungry 3D routers and wireless nodes. Moreover, the non-uniform distributed traffic in a chip multiprocessor (CMP) demands an on-chip communication infrastructure that can avoid congestion under high traffic conditions while possessing minimal pipeline delay at low-load conditions. To this end, in this paper, we propose a low-latency adaptive router with a low-complexity single-cycle bypassing mechanism to alleviate the performance degradation due to the slow 2D routers in such emerging hybrid NoCs. The proposed router transmits a flit using dimension-ordered routing (DoR) in the bypass datapath at low-loads. When the output port required for intra-dimension bypassing is not available, the packet is routed adaptively to avoid congestion. The router also has a simplified virtual channel allocation (VA) scheme that yields a non-speculative low-latency pipeline. By combining the low-complexity bypassing technique with adaptive routing, the proposed router is able to balance the traffic in hybrid NoCs to achieve low-latency communication under various traffic loads. Simulation shows that the proposed router can reduce applications’ execution time by an average of 16.9% compared to low-latency routers, such as SWIFT. By reducing the latency between 2D routers (or wired nodes) and 3D routers (or wireless nodes), the proposed router can improve the performance efficiency in terms of average packet delay by an average of 45 % (or 50 % ) in 3D NoCs (or WiNoCs).

Highlights

  • IntroductionRecent advances in cyber physical systems (CPS) that seamlessly integrate autonomous automobile systems, advanced distributed robotics, medical monitoring (complex biological sensing, computation and actuation), transform engineering and life sciences into a quantitative, data-rich scientific domain

  • Recent advances in cyber physical systems (CPS) that seamlessly integrate autonomous automobile systems, advanced distributed robotics, medical monitoring, transform engineering and life sciences into a quantitative, data-rich scientific domain

  • Two emerging wireless communication fabrics for wireless network-on-chip (WiNoC) are (1) the scalable millimetre wave, which relies on the free space signal radiation, and (2) the reliable 2D waveguide, where the signal is propagated in the form of the Zenneck surface wave (SW) on a specially-designed sheet, which is an inhomogeneous plane that supports electromagnetic wave transmission [6]

Read more

Summary

Introduction

Recent advances in cyber physical systems (CPS) that seamlessly integrate autonomous automobile systems, advanced distributed robotics, medical monitoring (complex biological sensing, computation and actuation), transform engineering and life sciences into a quantitative, data-rich scientific domain. The slow multi-hop communication, as well as high power consumption and poor scalability with technology of the conventional metal-based interconnects have propelled the research for alternative fabrics as supplementary interconnects for communication among remote cores in modern system-on-chip (SoC) design. Hybrid wired-wireless networks-on-chip (WiNoCs) have emerged to combine the global performance benefits of a CMOS-compatible wireless layer, as well as the short range low power and area benefits of the wireline communication fabric in NoCs. Two emerging wireless communication fabrics for WiNoCs are (1) the scalable millimetre wave (mm-wave), which relies on the free space signal radiation, and (2) the reliable 2D waveguide, where the signal is propagated in the form of the Zenneck surface wave (SW) on a specially-designed sheet, which is an inhomogeneous plane that supports electromagnetic wave transmission [6]. Our goal is to mitigate the performance reduction of such a communication fabric by proposing an efficient router architecture that accounts for the manufacturing cost in terms of area and power consumption

Objectives
Results
Conclusion
Full Text
Published version (Free)

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call