Abstract

It is shown that, growth of the layer with compressive residual stresses at advanced surface plastic deformation of smooth samples leads to an increase in the endurance limit of the notched specimens due to an increase in the compressive residual stresses in their dangerous section. The study was conducted on the specimens with outer diameterDequal to 10 and 25 mm and on a 25 mm specimen with inner diameterd= 15 mm which were subjected to air shot blasting and roll-in. Residual stresses in smooth specimens were determined by the mechanical method. Circular incisions (R= 0.3 and 0.5 mm) were applied on hardened smooth samples with a shaped cutter. Residual stresses in notched specimens were determined by a numerical method calculating the redistribution of the residual stresses upon the incision. As the diameter of the samples increases with the same strengthening surface treatment,the depth of the layer with the compressive residual stresses increases due to an increase in the rigidity of the samples. The effect of surface hardening on the endurance limit of notched specimens was evaluated according to the criterion of the average integral residual stresses, which takes into account both the magnitude and completeness of the residual stresses. This criterion was calculated from the depth of the non-propagating fatigue crack that occurs in the surface layer in the dangerous section of the specimen during the fatigue test at the limit endurance. Fatigue tests are carried out in symmetrical cycle, the test base being 3 × 106cycles of loading. Estimation of the increment of the limit endurance of surface-hardened cylindrical specimens with semicircular notches gave the results acceptable for practice. The use of the proposed method can significantly reduce long-term and expensive fatigue tests.

Highlights

  • Ïðîâåäåííîå èññëåäîâàíèå ïîêàçàëî, ÷òî ïðè îïåðåæàþùåì ïîâåðõíîñòíîì ïëàñòè÷åñêîì äåôîðìèðîâàíèè ãëàäêèõ îáðàçöîâ óâåëè÷åíèå ãëóáèíû ñëîÿ ñî ñæèìàþùèìè îñòàòî÷íûìè íàïðÿæåíèÿìè ïðèâîäèò ê ïîâûøåíèþ ïðåäåëà âûíîñëèâîñòè îáðàçöîâ ñ íàäðåçàìè çà ñ÷åò óâåëè÷åíèÿ ñæèìàþùèõ îñòàòî÷íûõ íàïðÿæåíèé â èõ îïàñíîì ñå÷åíèè

  • Growth of the layer with compressive residual stresses at advanced surface plastic deformation of smooth samples leads to an increase in the endurance limit of the notched specimens due to an increase in the compressive residual stresses in their dangerous section

  • The effect of surface hardening on the endurance limit of notched specimens was evaluated according to the criterion of the average integral residual stresses, which takes into account both the magnitude and completeness of the residual stresses

Read more

Summary

Introduction

Ïðîâåäåííîå èññëåäîâàíèå ïîêàçàëî, ÷òî ïðè îïåðåæàþùåì ïîâåðõíîñòíîì ïëàñòè÷åñêîì äåôîðìèðîâàíèè ãëàäêèõ îáðàçöîâ óâåëè÷åíèå ãëóáèíû ñëîÿ ñî ñæèìàþùèìè îñòàòî÷íûìè íàïðÿæåíèÿìè ïðèâîäèò ê ïîâûøåíèþ ïðåäåëà âûíîñëèâîñòè îáðàçöîâ ñ íàäðåçàìè çà ñ÷åò óâåëè÷åíèÿ ñæèìàþùèõ îñòàòî÷íûõ íàïðÿæåíèé â èõ îïàñíîì ñå÷åíèè. DEPENDENCE OF THE LIMIT ENDURANCE OF SPECIMENS WITH NOTCHES FROM THE DEPTH OF HARDENED SURFACE LAYER Growth of the layer with compressive residual stresses at advanced surface plastic deformation of smooth samples leads to an increase in the endurance limit of the notched specimens due to an increase in the compressive residual stresses in their dangerous section.

Results
Conclusion

Talk to us

Join us for a 30 min session where you can share your feedback and ask us any queries you have

Schedule a call

Disclaimer: All third-party content on this website/platform is and will remain the property of their respective owners and is provided on "as is" basis without any warranties, express or implied. Use of third-party content does not indicate any affiliation, sponsorship with or endorsement by them. Any references to third-party content is to identify the corresponding services and shall be considered fair use under The CopyrightLaw.