Deep Eutectic Solvent Supported Polymer-Based High Performance Anion Exchange Membrane for Alkaline Fuel Cells

Abstract

Alkaline anion exchange membrane fuel cells (AEMFC) have gained interest due to their potential as electrochemically energy conversion devices and a competitive alternative to the more extensively studied commercialized proton exchange membrane fuel cells (PEMFCs). Nevertheless, their development impedes the limited ion conductivity, chemical and mechanical stability in an alkaline medium of anion exchange membranes (AEMs). The ionic conductivity of AEM is lower than that of a proton exchange membrane (PEM) because the mobility of hydroxide ions is inherently lower than that of protons [1]. Deep eutectic solvents (DESs) as green solvents can overcome this issue.The main idea of this research is to fabricate a deep eutectic solvent-supported polymer-based AEM for alkaline fuel cell application by electrospinning technique. Poly(vinyl alcohol) (PVA) is one of the potential polymers for the development of AEM due to its water solubility, biodegradability, high fiber forming ability, non-toxicity, and high chemical and thermal stability [2]. This work aims to achieve high ionic conductivity, chemical and mechanical stability by two methods: swelling polyvinyl alcohol (PVA)-based nanofibers into DES and encapsulating DES inside the PVA-nanofibers together with optimizing fabrication methods.In this study, polymer electrolytes as potential AEMs were first prepared using the swelling method, where electrospun PVA nanofibers were fabricated via the electrospinning technique, followed by swelling in a series of DESs. To prepare the DES solutions, choline chloride (ChCl) and ethylene glycol (EG) were mixed at different molar ratios. The cross-linking of pure PVA fibers with glutaraldehyde in ethanol (see Figure 1B) and DES uptake and the presence of voids as channels for ion conduction (see Figure 1C) were successfully confirmed with a scanning electron microscopy (SEM, Crossbeam500, Zeiss). The ionic conductivity of swelled in DES PVA-based membranes were evaluated by electrochemical impedance spectroscopy (Metrohm Autolab) at room temperature and was equal to 0.336 mS/cm. The presence of DES in the membrane was confirmed with FTIR spectroscopy (FT-IR spectrometer, Nicolet iS10): a slight C-N+ peak at 953 cm-1 from ChCl has proven interaction between PVA and DES with FTIR spectroscopy, meaning that DES is present in the fiber. In addition, the nitrogen content in the obtained membrane was determined by CHNS elemental analysis (Elemental Vario micro cube) as 3.32 wt.%.In order to overcome high weight loss in the swelling method, the encapsulation method was suggested as an alternative option, which is based on the encapsulation of DES into the PVA solution by mixing them, varying the amount of DES added, and then preparing fibers using electrospinning. Observing the morphology of DES-encapsulated PVA nanofibers with a scanning electron microscope (SEM, Crossbeam500, Zeiss), as the content of DES in the solution increased, there was an observed rise in the average diameter of the nanofibers (see Figure 1D). Encapsulation of DES in PVA nanofibers was primarily confirmed by transmission electron microscope (TEM, JEM -1400 Plus, JEOL): PVA appears lighter due to its decreased density, proving that DES is present inside the fibers. Also, the same tendency was observed with the results of FTIR spectroscopy (FT-IR spectrometer, Nicolet iS10) as for the swelling method, meaning that DES is present in the fiber. According to CHNS elemental analysis (Elemental Vario micro cube), nitrogen content was lower than for the swelling method - 0.70 wt.%. The ionic conductivity was evaluated as 0.364 mS/cm by electrochemical impedance spectroscopy (Metrohm Autolab) at room temperature, which was almost the same as for the swelling method.As a result, very flexible and visually transparent electrospun DES-supported PVA-based AEMs were obtained via the swelling and encapsulation method.