Zirconium-based Metal-organic Framework Research Articles

A facile and efficient voltammetric sensor for marbofloxacin detection based on zirconium-based metal-organic framework UiO-66/nitrogen-doped graphene nanocomposite

Improper and persistent use of marbofloxacin (MAR) is prone to produce residues that deteriorate the surrounding environment and endanger our health. Hence, it is urgent to stablish a facile and efficient detection technique for the detection of MAR. Herein, a highly efficient electrochemical platform was constructed for sensitive determination of MAR using zirconium-based metal–organic framework (UiO-66)/nitrogen-doped graphene (NG) nanocomposites (UiO-66/NG). The surface morphology, crystalline phase elemental composition, and electrochemical behavior of UiO-66/NG were characterized by various spectroscopic and electrochemical techniques. Owing to the synergistic interaction of UiO-66 MOFs and NG nanosheets, the UiO-66/NG exhibited remarkable catalytic activity for MAR oxidation. As consequently, the UiO-66/NG demonstrated a wide linear response range (0.01 − 10 μM), high sensitivity (1.80 μM μA−1 cm−2) and low detection limit (0.002 μM). The proposed UiO-66/NG/GCE demonstrated robust voltammetric responses even in the presence of excess potential interfering species and retained stable response signals for at least two weeks. More importantly, the proposed UiO-66/NG/GCE displayed highly consistent sensitivity toward MAR detection in both aquaculture water matrices and PBS buffer, and achieved accurate and sensitive detection of MAR with good recovery. Together with its low cost and facile operation, the UiO-66/NG/GCE shows great prospects for trace detection of MAR from complex matrices.

Defect-enabling zirconium-based metal-organic frameworks for energy and environmental remediation applications.

This comprehensive review explores the diverse applications of defective zirconium-based metal-organic frameworks (Zr-MOFs) in energy and environmental remediation. Zr-MOFs have gained significant attention due to their unique properties, and deliberate introduction of defects further enhances their functionality. The review encompasses several areas where defective Zr-MOFs exhibit promise, including environmental remediation, detoxification of chemical warfare agents, photocatalytic energy conversions, and electrochemical applications. Defects play a pivotal role by creating open sites within the framework, facilitating effective adsorption and remediation of pollutants. They also contribute to the catalytic activity of Zr-MOFs, enabling efficient energy conversion processes such as hydrogen production and CO2 reduction. The review underscores the importance of defect manipulation, including control over their distribution and type, to optimize the performance of Zr-MOFs. Through tailored defect engineering and precise selection of functional groups, researchers can enhance the selectivity and efficiency of Zr-MOFs for specific applications. Additionally, pore size manipulation influences the adsorption capacity and transport properties of Zr-MOFs, further expanding their potential in environmental remediation and energy conversion. Defective Zr-MOFs exhibit remarkable stability and synthetic versatility, making them suitable for diverse environmental conditions and allowing for the introduction of missing linkers, cluster defects, or post-synthetic modifications to precisely tailor their properties. Overall, this review highlights the promising prospects of defective Zr-MOFs in addressing energy and environmental challenges, positioning them as versatile tools for sustainable solutions and paving the way for advancements in various sectors toward a cleaner and more sustainable future.

Two-dimensional metal–organic framework for post-synthetic immobilization of graphene quantum dots for photoluminescent sensing

Immobilization of graphene quantum dots (GQDs) on a solid support is crucial to prevent GQDs from aggregation in the form of solid powder and facilitate the separation and recycling of GQDs after use. Herein, spatially dispersed GQDs are post-synthetically coordinated within a two-dimensional (2D) and water-stable zirconium-based metal–organic framework (MOF). Unlike pristine GQDs, the obtained GQDs immobilized on 2D MOF sheets show photoluminescence in both suspension and dry powder. Chemical and photoluminescent stabilities of MOF-immobilized GQDs in water are investigated, and the use of immobilized GQDs in the photoluminescent detection of copper ions is demonstrated. Findings here shed the light on the use of 2D MOFs as a platform to further immobilize GQDs with various sizes and distinct chemical functionalities for a range of applications.

CO2-Based Stable Porous Metal-Organic Frameworks for CO2 Utilization.

The transformation of carbon dioxide (CO2) into functional materials has garnered considerable worldwide interest. Metal-organic frameworks (MOFs), as a distinctive class of materials, have made great contributions to CO2 capture and conversion. However, facile conversion of CO2 to stable porous MOFs for CO2 utilization remains unexplored. Herein, we present a facile methodology of using CO2 to synthesize stable zirconium-based MOFs. Two zirconium-based MOFs CO2-Zr-DEP and CO2-Zr-DEDP with face-centered cubic topology were obtained via a sequential desilylation-carboxylation-coordination reaction. The MOFs exhibit excellent crystallinity, as verified through powder X-ray diffraction and high-resolution transmission electron microscopy analyses. They also have notable porosity with high surface area (SBET up to 3688 m2 g-1) and good CO2 adsorption capacity (up to 12.5 wt %). The resulting MOFs have abundant alkyne functional moieties, confirmed through 13C cross-polarization/magic angle spinning nuclear magnetic resonance and Fourier transform infrared spectra. Leveraging the catalytic prowess of Ag(I) in diverse CO2-involved reactions, we incorporated Ag(I) into zirconium-based MOFs, capitalizing on their interactions with carbon-carbon π-bonds of alkynes, thereby forming a heterogeneous catalyst. This catalyst demonstrates outstanding efficiency in catalyzing the conversion of CO2 and propargylic alcohols into cyclic carbonates, achieving >99% yield at room temperature and atmospheric pressure conditions. Thus, this work provides a dual CO2 utilization strategy, encompassing the synthesis of CO2-based MOFs (20-24 wt % from CO2) and their subsequent application in CO2 capture and conversion processes. This approach significantly enhances overall CO2 utilization.

Polyvinyl Alcohol/Zr-based Metal Organic Framework Mixed-matrix Membranes Synthesis and Application for Hydrogen Separation

AbstractMembrane gas separation is an environmentally friendly and economical method used to separate valuable gases, industrial process gas wastes, and carbon dioxide from mixed gases. The most important part of this method is the membranes. Gas separation membranes are expected to have high separation and permeability performance, high mechanical strength, easy and fast production capability, and low prices. Polymer-based membranes are mostly preferred depending on the ease of modification capability. In this study, a zirconium-based metal organic framework (Zr-MOF, MIL-140 A) was synthesized and used as a filler within polyvinyl alcohol (PVA) matrix for the selective separation of hydrogen (H2) from carbon dioxide (CO2). The effect of MIL-140 A addition on the mechanical, structural, and morphological properties of PVA was evaluated. The MIL-140 A significantly improved the mechanical strength of the membrane. According to the gas separation results, the increasing concentration of MIL-140 A increased the selective separation performance of the nanocomposite membrane. The highest mechanical strength (43.1 MPa) and best film-forming ability were obtained with 3 wt% MIL-140 A loaded membrane. The ideal H2/CO2 selectivity and hydrogen permeability were obtained as 5.6 and 944 Barrer, respectively at 2 bar feed pressure and room temperature. The highest ideal H2/CO2 selectivity was obtained as 6.3 with the H2 permeability of 959 Barrer when the MIL-140 A ratio was 4 wt%.

High performance multifunctional piezoelectric PAN/UiO-66-NO2/MXene composite nanofibers for flexible touch sensor

In this study, a flexible piezoelectric sensor based on polyacrylonitrile (PAN), zirconium-based MOF (UiO-66) with nitro (NO2) and two-dimensional material MXene composite nanofiber film was proposed. When pressure was applied, the three-dimensional structural nanopores were compressed, increasing the intercalation structure between the MXene nanosheets coated in the fibers. The double-packed system produced a higher resistance change under the same pressure load, which can be explained by the fact that the low-conductivity octahedral UiO-66-NO2 particles acted as a similar “buffer” between the highly conductive MXene. At the same time, a large number of hydrogen bonds between the surfaces of the two fillers enhanced the synergistic effect and promoted the interfacial coupling effect, so that more 31-helical conformation in the PAN matrix was converted into a planar zigzag conformation. This improved the piezoelectric performance and enabled the sensor to have a voltage output of about 200 V in the detection range. And because the polyhedral form of UiO-66-NO2 particles provided a rougher surface structure, the piezoelectric sensor can achieve a high sensitivity of 5.62 V/N. The other results showed that the dielectric constant of the designed flexible piezoelectric sensor was increased to 2.67, the dielectric loss was kept at a low level of 0.026, and the maximum elongation was 56.03 %. This multi-functional sensor shows great potential in the fields of health and medical treatment, human-computer interaction, etc.

Reticular Chemistry Directed "One-Pot" Strategy to in situ Construct Organic Linkers and Zirconium-Organic Frameworks.

Zirconium-based metal-organic frameworks (Zr-MOFs) have emerged as one of the most studied MOFs due to the unlimited numbers of organic linkers and the varying Zr-oxo clusters. However, the synthesis of carboxylic acids, especially multitopic carboxylic acids, is always a great challenge for the discovery of new Zr-MOFs. As an alternative approach, the in situ "one-pot" strategy can address this limitation, where the generation of organic linkers from the corresponding precursors and the sequential construction of MOFs are integrated into one solvothermal condition. Herein, inspired by benzimidazole-contained compounds synthesized via reaction of aldehyde and o-phenylenediamine, tri-, tetra-, penta- and hexa-topic carboxylic acids and a series of corresponding Zr-MOFs can be prepared via the in situ "one-pot" method under the same solvothermal conditions. This strategy can be utilized not only to prepare reported Zr-MOFs constructed using benzimidazole-contained linkers, but also to rationally design, construct and realize functionalities of zirconium-pentacarboxylate frameworks guided by reticular chemistry. More importantly, in situ "one-pot" method can facilitate the discovery of new Zr-MOFs, such as zirconium-hexacarboxylate frameworks. The present study demonstrates the promising potential of benzimidazole-inspired in situ "one-pot" approach in the crystal engineering of structure- and property-specific Zr-MOFs, especially with the guidance of reticular chemistry.

Integrating metal-organic framework particles on fabric membranes for decontaminating toxic organophosphates

Zirconium-based metal-organic frameworks (Zr-MOFs) with periodic Lewis acidic nodes have demonstrated impressive catalytic activity in the hydrolysis of organophosphorus nerve agents. Nevertheless, the powdered form of Zr-MOFs and the necessity of a base-buffered aqueous solution during the catalytic reaction pose significant challenges to their practical utilization. In this study, we demonstrate the efficient hydrolysis of an organophosphorus nerve agent simulant, dimethyl-4-nitrophenyl phosphate (DMNP), in both pure water and the solid phase under high humidity conditions, catalyzed by a membrane material. This material, denoted as Im@MOF-808/PVDF, was synthesized through the integration of MOF-808 particles onto PVDF membrane fibers, with imidazole (Im) molecular bases incorporated into the pores of MOF-808. Our findings emphasize the excellent flexibility and processability inherent in Im@MOF-808/PVDF. More notably, it exhibits exceptional catalytic performance in the hydrolysis of DMNP in pure water. Additionally, it demonstrates fair catalytic activity for solid-phase DMNP hydrolysis under high humidity conditions. These features position Im@MOF-808/PVDF as one of the most promising protective materials, showcasing substantial practical applicability.

High-Resolution and Dynamic Visualization of Intracellular Redox Potential Using a Metal-Organic Framework-Functionalized Nanopotentiometer.

Redox potential plays a key role in regulating intracellular signaling pathways, with its quantitative analysis in individual cells benefiting our understanding of the underlying mechanism in the pathophysiological events. Here, a metal organic framework (MOF)-functionalized SERS nanopotentiometer has been developed for the dynamic monitoring of intracellular redox potential. The approach is based on the encapsulation of zirconium-based MOF (Uio-66-F4) on a surface of gold-silver nanorods (Au-Ag NRs) that is modified with the newly synthesized redox-sensitive probe ortho-mercaptohydroquinone (HQ). Thanks to size exclusion of MOF as the chemical protector, the nanopotentiometer can be adapted to long-term use and possess high anti-interference ability toward nonredox species. Combining the superior fingerprint identification of SERS with the electrochemical activity of the quinone/hydroquinone, the nanopotentiometer shows a reversible redox responsivity and can quantify redox potential with a relatively wide range of -250-100 mV. Furthermore, the nanopotentiometer allows for dynamic visualization of intracellular redox potential changes induced by drugs' stimulation in a high-resolution manner. The developed approach would be promising for offering new insights into the correlation between redox potential and tumor proliferation-involved processes such as oxidative stress and hypoxia.

Efficient Cr(VI) remediation by electrospun composite porous nanofibers incorporating biomass with metal oxides and metal-organic framework

To develop a highly efficient adsorbent to remediate and remove hexavalent chromium ions (Cr(VI)) from polluted water, cellulose acetate (CA) and chitosan (CS), along with metal oxides (titanium dioxide (TiO2) and ferroferric oxide (Fe3O4)), and a zirconium-based metal-organic framework (UiO-66) were used to fabricate the composite porous nanofiber membranes through electrospinning. The adsorption performance, influencing factors, adsorption kinetics and isotherms of composite nanofiber membranes were comprehensively investigated. The multi-layer membrane with interpenetrating nanofibers and surface functional groups enhanced the natural physical adsorption and provided potential chemical sites. The thermal stability was improved by introducing TiO2 and UiO-66. CA/CS/UiO-66 exhibited the highest adsorption capacity (118.81 mg g−1) and removal rate (60.76%), which were twice higher than those of the control. The correlation coefficients (R2) of all the composite nanofibers regressed by the Langmuir model were significantly higher than those by the Freundlich model. The pseudo-first-order kinetic curve of CA/CS composite nanofibers showed the highest R2 (0.973), demonstrating that the whole adsorption process involved a combination of strong physical adsorption and weak chemical adsorption by the amino groups of CS. However, the R2 values of the pseudo-second-order kinetic model increased after incorporating TiO2, Fe3O4, and UiO-66 into the CA/CS composite nanofiber membranes since an enhanced chemical reaction with Cr (VI) occured during the adsorption

Water Catchers within Sub-Nano Channels Promote Step-by-Step Zinc-Ion Dehydration Enable Highly Efficient Aqueous Zinc-Metal Batteries.

Zinc metal suffers from violent and long-lasting water-induced side reactions and uncontrollable dendritic Zn growth, which seriously reduce the coulombic efficiency (CE) and lifespan of aqueous zinc-metal batteries (AZMBs). To suppress the corresponding harmful effects of the highly active water, a stable zirconium-based metal-organic framework with water catchers decorated inside its sub-nano channels is used to protect Zn-metal. Water catchers within narrow channels can constantly trap water molecules from the solvated Zn-ions and facilitate step-by-step desolvation/dehydration, thereby promoting the formation of an aggregative electrolyte configuration, which consequently eliminates water-induced corrosion and side reactions. More importantly, the functionalized sub-nano channels also act as ion rectifiers and promote fast but even Zn-ions transport, thereby leading to a dendrite-free Zn metal. As a result, the protected Zn metal demonstrates an unprecedented cycling stability of more than 10000 h and an ultra-high average CE of 99.92% during 4000 cycles. More inspiringly, a practical NH4V4O10//Zn pouch-cell is fabricated and delivers a capacity of 98 mAh (under high cathode mass loading of 25.7mg cm-2) and preserves 86.2% capacity retention after 150 cycles. This new strategy in promoting highly reversible Zn metal anodes would spur the practical utilization of AZMBs.

Fabrication of phosphorylated UiO-66 for efficient selective removal of Pb2+ from acidic wastewater

Metal-organic framework (MOF) materials have emerged as promising candidates for treating heavy metal wastewater because of their controllable pore size, high specific surface area, and abundant active sites. Nevertheless, the currently reported MOFs usually require near-neutral environments (pH = 5–6) to achieve efficient removal of Pb2+ and cannot be applied to acidic environments (pH = 2–3). In this work, the structurally stabilized zirconium-based MOF UiO-66 was chosen as the object of study. Three phosphate ester-based MOFs (UiO-66-(OPO3)X) containing different amounts and spatial positions were designed and prepared by simple chemical modification and used to remove Pb2+. Adsorption experiments showed that they could reach adsorption equilibrium in 30 min with excellent adsorption rate. Owing to the unique ionization ability of the phosphate ester group, UiO-66-(OPO3)X maintains a high removal efficiency of Pb2+ even at pH = 2 and pH = 3. In addition, selectivity and competition experiments demonstrated that UiO-66-(OPO3)X possessed excellent selectivity and anticompetitive ability towards Pb2+.The excellent regeneration performance demonstrates their value for practical application. Moreover, the adsorption mechanism was investigated in detail by experiment combined with density functional theory (DFT).

Enhancing Drug Delivery Efficacy Through Bilayer Coating of Zirconium-Based Metal-Organic Frameworks: Sustained Release and Improved Chemical Stability and Cellular Uptake for Cancer Therapy.

The development of nanoparticle (NP)-based drug carriers has presented an exciting opportunity to address challenges in oncology. Among the 100,000 available possibilities, zirconium-based metal-organic frameworks (MOFs) have emerged as promising candidates in biomedical applications. Zr-MOFs can be easily synthesized as small-size NPs compatible with intravenous injection, whereas the ease of decorating their external surfaces with functional groups allows for targeted treatment. Despite these benefits, Zr-MOFs suffer degradation and aggregation in real, in vivo conditions, whereas the loaded drugs will suffer the burst effect-i.e., the fast release of drugs in less than 48 h. To tackle these issues, we developed a simple but effective bilayer coating strategy in a generic, two-step process. In this work, bilayer-coated MOF NU-901 remained well dispersed in biologically relevant fluids such as buffers and cell growth media. Additionally, the coating enhances the long-term stability of drug-loaded MOFs in water by simultaneously preventing sustained leakage of the drug and aggregation of the MOF particles. We evaluated our materials for the encapsulation and transport of pemetrexed, the standard-of-care chemotherapy in mesothelioma. The bilayer coating allowed for a slowed release of pemetrexed over 7 days, superior to the typical 48 h release found in bare MOFs. This slow release and the related performance were studied in vitro using both A549 lung cancer and 3T mesothelioma cells. Using high-resolution microscopy, we found the successful uptake of bilayer-coated MOFs by the cells with an accumulation in the lysosomes. The pemetrex-loaded NU-901 was indeed cytotoxic to 3T and A549 cancer cells. Finally, we demonstrated the general approach by extending the coating strategy using two additional lipids and four surfactants. This research highlights how a simple yet effective bilayer coating provides new insights into the design of promising MOF-based drug delivery systems.

UiO-66 uniformly assembled foldable polyimide films with high transmittance and excellent ultraviolet resistance

As a protective layer for the flexible solar cell, a flexible protective material should be of high transmittance, excellent ultraviolet (UV) resistance and mechanical property. Herein, a foldable transparent polyimide (PI) composite film assembled with the zirconium-based metal-organic frameworks (UiO-66-X, X = H, NH2, NO2) is prepared by the direct dispersion or in-situ growth methods. The results show that the transmittances of UiO-66-X@PI films (U@PI, NU@PI and OU@PI) prepared with the in-situ growth are higher than those of UiO-66-X/PI films prepared with the direct dispersion, and the former's mechanical properties are also better than those of the latter. This may be because that the UiO-66-X in the former are embedded into the PI matrix to construct multipoint bonding network. The U@PI exhibits stronger UV-resistance than the Pristine PI, NU@PI and OU@PI after 5000 equivalent sun hours (ESHs) UV irradiation. The attenuations of average transmittance and tensile strength for U@PI are 2.19 % and 18.68 %, respectively, which are only one half and one-third of those for the Pristine PI (4.59 % and 56.58 %), respectively. And the average transmittance of U@PI has been over that of the Pristine PI after 5000 ESHs UV irradiation. This may be because that the porous UiO-66 increases the UV transmission path and the electron-hole recombination center, thereby inhibits the destructive effect of UV.

Programmable Water Sorption through Linker Installation into a Zirconium Metal-Organic Framework.

Hydrolytically stable materials exhibiting a wide range of programmable water sorption behaviors are crucial for on-demand water sorption systems. While notable advancements in employing metal-organic frameworks (MOFs) as promising water adsorbents have been made, developing a robust yet easily tailorable MOF scaffold for specific operational conditions remains a challenge. To address this demand, we employed a topology-guided linker installation strategy using NU-600, which is a zirconium-based MOF (Zr-MOF) that contains three vacant crystallographically defined coordination sites. Through a judicious selection of three N-heterocyclic auxiliary linkers of specific lengths, we installed them into designated sites, giving rise to six new MOFs bearing different combinations of linkers in predetermined positions. The resulting MOFs, denoted as NU-606 to NU-611, demonstrate enhanced structural stability against capillary force-driven channel collapse during water desorption due to the increased connectivity of the Zr6 clusters in the resulting MOFs. Furthermore, incorporating these auxiliary linkers with various hydrophilic N sites enables the systematic modulation of the pore-filling pressure from about 55% relative humidity (RH) for the parent NU-600 down to below 40% RH. This topology-driven linker installation strategy offers precise control of water sorption properties for MOFs, highlighting a facile route to design MOF adsorbents for use in water sorption applications.

Gelatin- zirconium based metal-organic framework (MOF 801) nanocomposite scaffold for bone tissue engineering

Tissue engineering applications in bone defect treatment have shown promising outcomes over the past decade. In this context, taking advantage of bioactive scaffolds mimicking the intrinsic composition of bone has resulted in remarkable effects on bone regeneration. In this study, Zirconium-based metal-organic framework, known as MOF 801, was synthesized and incorporated into the gelatin matrix as an osteoconductive agent to fabricate a nanocomposite bone scaffold by freeze-drying method. Physical and chemical characteristics of MOF 801 and nanocomposite scaffolds were analyzed using FE-SEM, EDS, XRD, ICP and FTIR. Besides, the biological activity of the prepared scaffolds was evaluated by MTT, alizarin red staining, crystal violet staining, and ALP assays. Inclusion of MOF 801 NPs into the scaffolds resulted in enhancement of their compressive strength up to 15 ± 0.05 MPa. The nanocomposite samples containing MOF 801 NPs also exhibited favorable bioactive feature that was confirmed by their apatite-forming ability on their surfaces upon immersion in SBF solution. The Zr ion and fumarate release studies illustrated sustained release profiles from the gelatin matrix, leading to both antioxidant and anti-inflammatory properties. MTT assay results affirmed biocompatibility of scaffolds containing up to 5 % w/w MOF 801, besides the crystal violet assay exhibited proper cell confluency and adhesion. Eventually, Alizarin red and ALP activity assays revealed that an increment of MOF 801 could induce calcium mineralization and Alkaline Phosphatase enzyme production in MG-63 cells confirming the potential of prepared scaffolds for related bone tissue engineering applications.

UiO-66 metal-organic frameworks as aldol condensation catalyst: Impact of defects, solvent, functionality on the catalytic activity and selectivity

Defected and amine-loaded zirconium-based metal–organic frameworks (MOF) UiO-66(Zr) have been characterized and chemically assessed in a condensation reaction of acetone and 4-nitrobenzaldehyde. The present work focuses primarily on the production of the aldol adduct as the main product while minimizing the formation of the enone adduct as a side product. Four analogues with varying numbers of missing linkers in the hexanuclear secondary building units, from one to four out of a total of 12, were synthesized. Thorough characterization showed that an increased number of defects results in an enhanced acidity, a higher internal surface area, and an increased accessibility of coordinatively unsaturated Zr-sites. The catalytic performance assessment revealed that defects, to a certain extent, positively affect the selectivity towards the aldol adduct, i,e. the catalyst, which is missing 3 of the 12 linkers, exhibits the highest activity in a solvent-free environment with a turnover frequency (TOF) amounting to 8.03 10-3 s−1. This TOF value is approximately double of the catalyst with 1.4 defects, which exhibited a TOF of only 4.41 10-3 s−1. Excluding more than three linkers more likely leads to 'missing cluster defects' and causes a decrease in the reaction rate towards the aldol adduct. A reduction in overall catalytic activity was observed upon functionalization with amine groups (UiO-66-NH2). Functionalization with L-proline (UiO-66Lpr) resulted in a shift from an acid to a basic reaction mechanism which was reflected by an improved selectivity towards the aldol adduct while maintaining a reasonable overall activity level. The best performances were obtained working solvent-free or with hexane as a solvent, while polar/semi-polar solvents hindered the catalyst performance. An 18-hour stability test demonstrated the robustness of defected and functionalized UiO-66.

Preparation of formic acid-modified zirconium based metal organic frameworks for toluene absorption

UiO-66 is a widely used metal-organic frameworks in air pollution control. Volatile organic compounds (VOCs) are the important atmosphere pollutants that damage atmospheric environment and people health. UiO-66 was prepared by solvothermal method and modified with formic acid. All the materials were successfully prepared and characterized by XRD, BET, SEM, TG and FTIR, and the adsorption ability of UiO-66 was tested by toluene. The results showed that the BET specific surface area of UiO-66 synthesized by formic acid doping was enhanced, and the adsorption capacity of the doped adsorbent was significantly higher than that of UiO-66, which could reach up to 424.9 mg/g when the doping amount of formic acid was 20 mmol. The addition of acid during the reaction process could inhibit the recrystallization of H2BDC, which was beneficial for the pore structure construction of the material. Meanwhile, the material was subjected to static and dynamic adsorption, as well as adsorption-desorption continuous cycle experiments, which showed that the material has high thermal stability, and the desorption efficiency was 90.8% after five cycle experiments. The addition of formic acid can improve the adsorption performance of the specific surface area of UiO-66.

Study of process parameters that enable direct spray drying synthesis of UiO-66-NH2

This study explores the direct spray drying synthesis of UiO-66-NH2, a zirconium-based metal-organic framework (MOF). Focusing on the impact of process parameters on yield and purity, this research employs a solvent-free approach, integrating continuous manufacturing principles for a more sustainable and efficient production process. The influence of gas flow rate, inlet temperature, feed flow rate, and precursor solutions solid loading (SL) were systematically investigated. The prepared samples, mainly at two different precursor solid loadings; labelled as 3%SL-UiO-66-NH2 and 6%SL-UiO-66-NH2, were fully characterised and benchmarked against the solvothermal prepared sample. X-Ray diffraction (XRD) analysis indicated the ability to prepare a totally crystalline UiO-66-NH2 at 150 °C inlet temperature at 3% and 6% SL, without any preheating/mixing steps, and regardless of the other process conditions. Thermogravimetric analysis (TGA) indicated the presence of a higher degree of structural defects within the 3%SL-UiO-66-NH2 sample. The CO2 adsorption capacity was consistent with the decreasing order of surface area and defects as 3%SL-UiO-66-NH2 > STH-UiO-66-NH2 > 6%SL-UiO-66-NH2. This work provides insight into green synthesis and process optimization for MOF synthesis which is beneficial for industrial applications.

Exceptionally High Perfluorooctanoic Acid Uptake in Water by a Zirconium-Based Metal-Organic Framework through Synergistic Chemical and Physical Adsorption.

Perfluorooctanoic acid (PFOA) is an environmental contaminant ubiquitous in water resources, which as a xenobiotic and carcinogenic agent, severely endangers human health. The development of techniques for its efficient removal is therefore highly sought after. Herein, we demonstrate an unprecedented zirconium-based MOF (PCN-999) possessing Zr6 and biformate-bridged (Zr6)2 clusters simultaneously, which exhibits an exceptional PFOA uptake of 1089 mg/g (2.63 mmol/g), representing a ca. 50% increase over the previous record for MOFs. Single-crystal X-ray diffraction studies and computational analysis revealed that the (Zr6)2 clusters offer additional open coordination sites for hosting PFOA. The coordinated PFOAs further enhance the interaction between coordinated and free PFOAs for physical adsorption, boosting the adsorption capacity to an unparalleled high standard. Our findings represent a major step forward in the fundamental understanding of the MOF-based PFOA removal mechanism, paving the way toward the rational design of next-generation adsorbents for per- and polyfluoroalkyl substance (PFAS) removal.