X-ray Phase-contrast Imaging Setup Research Articles

A compact system for intraoperative specimen imaging based on edge illumination x-ray phase contrast

A significant number of patients receiving breast-conserving surgery (BCS) for invasive carcinoma and ductal carcinoma in situ (DCIS) may need reoperation following tumor-positive margins from final histopathology tests. All current intraoperative margin assessment modalities have specific limitations. As a first step towards the development of a compact system for intraoperative specimen imaging based on edge illumination x-ray phase contrast, we prove that the system’s dimensions can be reduced without affecting imaging performance.We analysed the variation in noise and contrast to noise ratio (CNR) with decreasing system length using the edge illumination x-ray phase contrast imaging setup. Two-(planar) and three-(computed tomography (CT)) dimensional imaging acquisitions of custom phantoms and a breast tissue specimen were made. Dedicated phase retrieval algorithms were used to separate refraction and absorption signals. A ‘single-shot’ retrieval method was also used, to retrieve thickness map images, due to its simple acquisition procedure and reduced acquisition times. Experimental results were compared to numerical simulations where appropriate.The relative contribution of dark noise signal in integrating detectors is significant for low photon count statistics acquisitions. Under constant exposure factors and magnification, a more compact system provides an increase in CNR. Superior CNR results were obtained for refraction and thickness map images when compared to absorption images. Results indicate that the ‘single-shot’ acquisition method is preferable for a compact CT intraoperative specimen scanner; it allows for shorter acquisition times and its combination of the absorption and refraction signals ultimately leads to a higher contrast. The first CT images of a breast specimen acquired with the compact system provided promising results when compared to those of the longer length system.

Intrinsic spatial resolution limit of the analyzer-based X-ray phase contrast imaging technique

Dynamical diffraction effects always play a role when working with perfect single crystals. The penetration of X-rays respect to the surface normal during diffraction (extinction depth - 1/σe) in perfect single crystals does not have a constant value. The value changes for different angular positions on the crystal diffraction condition. For higher X-ray energies this value can change from few micrometers to tens of millimeters for each different crystal angular position in the small angular range of the diffraction condition. This effect may spread a single point in the object (sample) as a line in the image detector, especially if the crystal is set (or if the sample angularly deviates the beam) at lower diffraction angle positions, where the surface component of X-ray penetration can achieve huge values. Then, for imaging experiments where the dynamical diffraction occurs, such intrinsic property can affect the image resolution. We have modeled and experimentally checked such a dynamical diffraction property using, as example, an Analyzer-based X-ray phase contrast imaging setup (ABI) at two different X-ray energies: 10.7 keV and 18 keV. The results show that our theoretical model is consistent with the measured results. For higher energies the blur effect is enhanced and intrinsically limits the image spatial resolution.

Laser ablation of high-aspect-ratio hole arrays in tungsten for X-ray applications

Periodic two-dimensional tungsten X-ray optical gratings were fabricated using a combination of pico-second laser ablation and wet chemical etch. A 200 μm thick cold-rolled sheet of tungsten (99.97%) was used as base material for the fabrication of a 1.5 × 1.5 cm2 periodic grating with an array of circular holes of approximately 12:1 aspect ratio. The laser parameters were optimized to obtain through-hole diameters slightly smaller than the desired final dimension. Subsequent wet etching was used to precisely control the diameter of through-holes. The through-hole profile was characterized using scanning electron microscopy (SEM) and showed a slight conical shape with a slope of 1.3%. The two-dimensional tungsten absorption grating was successfully tested in an X-ray phase-contrast imaging setup. The method has proven to have some relevant benefits, such as good reproducibility and fairly easy fabrication due to few manufacturing steps.

Visualization of dynamic fiber-matrix interfacial shear debonding

To visualize the debonding event in real time for the study of dynamic crack initiation and propagation at the fiber–matrix interface, a modified tension Kolsky bar was integrated with a high-speed synchrotron X-ray phase-contrast imaging setup. In the gage section, the pull-out configuration was utilized to understand the behavior of interfacial debonding between SC-15 epoxy matrix and S-2 glass fiber, tungsten wire, steel wire, and carbon fiber composite Z-pin at pull-out velocities of 2.5 and 5.0 m s−1. The load history and images of the debonding progression were simultaneously recorded. Both S-2 glass fiber and Z-pin experienced catastrophic interfacial debonding whereas tungsten and steel wire experienced both catastrophic debonding and stick–slip behavior. Even though S-2 glass fiber and Z-pin samples exhibited a slight increase and tungsten and steel wire samples exhibited a slight decrease in average peak force and average interfacial shear stress as the pull-out velocities were increased, no statistical difference was found for most properties when the velocity was increased. Furthermore, the debonding behavior for each fiber material is similar with increasing pull-out velocity. Thus, the debonding mechanism, peak force, and interfacial shear stress were rate insensitive as the pull-out velocity doubled from 2.5 to 5.0 m s−1. Scanning electron microscope imaging of recovered epoxy beads revealed a snap-back behavior around the meniscus region of the bead for S-2 glass, tungsten, and steel fiber materials at 5.0 m s−1 whereas those at 2.5 m s−1 exhibited no snap-back behavior.

PHASE-CONTRAST IMAGING BASED ON THREE-BLOCK FRESNEL ZONE PLATE INTERFEROMETERS USING HARD X-RAY LABORATORY SOURCES

The earlier represented three-block Fresnel Zone Plate interferometer based hard X-ray phase-contrast imaging setup designed for the initial plane wave radiation has been adapted to the laboratory sources of radiation. The limited distance between the source and the interferometer as well as the finite size of the source and the limited degree of monochromaticity of the illumination have been taken into account. It was shown that the decrease of the spatial coherency of the initial radiation does not worsen, and even improves the quality of the phase-contrast imaging, by suppressing the distortions caused by the X-ray diffraction at the edges of the Fresnel zone plates and the knifes of the interferometer.

Asymmetric masks for large field-of-view and high-energy X-ray phase contrast imaging

We report on a large field of view, laboratory-based X-ray phase-contrast imaging setup. The method is based upon the asymmetric mask design that enables the retrieval of the absorption, refraction and scattering properties of the sample without the need to move any component of the imaging system. This can be thought of as a periodic repetition of a group of three (or more) apertures arranged in such a way that each laminar beam, defined by the apertures, produces a different illumination level when analysed with a standard periodic set of apertures. The sample is scanned through the imaging system, also removing possible aliasing problems that might arise from partial sample illumination when using the edge illumination technique. This approach preserves the incoherence and achromatic properties of edge illumination, removes the problems related to aliasing and it naturally adapts to those situations in clinical, industrial and security imaging where the image is acquired by scanning the sample relative to the imaging system. These concepts were implemented for a large field-of-view set of masks (20 cm × 1.5 cm and 15 cm × 1.2 cm), designed to work with a tungsten anode X-ray source operated up to 80–100 kVp, from which preliminary experimental results are presented.

X-ray phase contrast tomography; proof of principle for post-mortem imaging

To demonstrate the feasibility of using X-ray phase-contrast tomography to assess internal organs in a post-mortem piglet model, as a possible non-invasive imaging autopsy technique. Tomographic images of a new-born piglet were obtained using a free-space propagation X-ray phase-contrast imaging setup at a synchrotron (European Synchrotron Radiation Facility, Grenoble, France). A monochromatic X-ray beam (52 keV) was used in combination with a detector pixel size of 46 × 46 µm(2). A phase-retrieval algorithm was applied to all projections, which were then reconstructed into tomograms using the filtered-back projection algorithm. Images were assessed for diagnostic quality. Images obtained with the free-space propagation setup presented high soft-tissue contrast and sufficient resolution for resolving organ structure. All of the main body organs (heart, lungs, kidneys, liver and intestines) were easily identified and adequately visualized. In addition, grey/white matter differentiation in the cerebellum while still contained within the skull was shown. The feasibility of using X-ray phase-contrast tomography as a post-mortem imaging technique in an animal model has been demonstrated. Future studies will focus on translating this experiment to a laboratory-based setup. Appropriate image processing and analysis enable the simultaneous visualization of both soft- and hard-tissue structures in X-ray phase-contrast images of a complex, thick sample.

A laboratory based edge-illumination x-ray phase-contrast imaging setup with two-directional sensitivity

We report on a preliminary laboratory based x-ray phase-contrast imaging system capable of achieving two-directional phase sensitivity, thanks to the use of L-shaped apertures. We show that in addition to apparent absorption, two-directional differential phase images of an object can be quantitatively retrieved by using only three input images. We also verify that knowledge of the phase derivatives along both directions allows for straightforward phase integration with no streak artefacts, a known problem common to all differential phase techniques. In addition, an analytical method for 2-directional dark field retrieval is proposed and experimentally demonstrated.

A user-friendly LabVIEW software platform for grating based X-ray phase-contrast imaging.

X-ray phase-contrast imaging can provide greatly improved contrast over conventional absorption-based imaging for weakly absorbing samples, such as biological soft tissues and fibre composites. In this study, we introduced an easy and fast way to develop a user-friendly software platform dedicated to the new grating-based X-ray phase-contrast imaging setup at the National Synchrotron Radiation Laboratory of the University of Science and Technology of China. The control of 21 motorized stages, of a piezoelectric stage and of an X-ray tube are achieved with this software, it also covers image acquisition with a flat panel detector for automatic phase stepping scan. Moreover, a data post-processing module for signals retrieval and other custom features are in principle available. With a seamless integration of all the necessary functions in one software package, this platform greatly facilitate users' activities during experimental runs with this grating based X-ray phase contrast imaging setup.

On a dark-field signal generated by micrometer-sized calcifications in phase-contrast mammography

We show that a distribution of micrometer-sized calcifications in the human breast which are not visible in clinical x-ray mammography at diagnostic dose levels can produce a significant dark-field signal in a grating-based x-ray phase-contrast imaging setup with a tungsten anode x-ray tube operated at 40 kVp. A breast specimen with invasive ductal carcinoma was investigated immediately after surgery by Talbot–Lau x-ray interferometry with a design energy of 25 keV. The sample contained two tumors which were visible in ultrasound and contrast-agent enhanced MRI but invisible in clinical x-ray mammography, in specimen radiography and in the attenuation images obtained with the Talbot–Lau interferometer. One of the tumors produced significant dark-field contrast with an exposure of 0.85 mGy air-kerma. Staining of histological slices revealed sparsely distributed grains of calcium phosphate with sizes varying between 1 and 40 μm in the region of this tumor. By combining the histological investigations with an x-ray wave-field simulation we demonstrate that a corresponding distribution of grains of calcium phosphate in the form of hydroxylapatite has the ability to produce a dark-field signal which would—to a substantial degree—explain the measured dark-field image. Thus we have found the appearance of new information (compared to attenuation and differential phase images) in the dark-field image. The second tumor in the same sample did not contain a significant fraction of these very fine calcification grains and was invisible in the dark-field image. We conclude that some tumors which are invisible in x-ray absorption mammography might be detected in the x-ray dark-field image at tolerable dose levels.

Optimization of the in-line X-ray phase-contrast imaging setup considering edge-contrast enhancement and spatial resolution

Employing the approximation theory based on refraction and the definition of the total point-spread-function of the imaging system, the variation in the edge contrast of simple model samples is discussed with different source-to-sample and sample-to-detector distances, which actually means different spatial resolutions of the imaging system. The experiments were carried out with the Beamline 4W1A imaging setup at the Beijing Synchrotron Radiation Facility for simple model and insect samples. The results show that to obtain clear phase-contrast images of biologic tissues for the X-ray in-line imaging setup, with determined parameters such as the size of the X-ray source, the pixel size of the detector and the fixed source-to-sample distance, there is a range of optimized sample-to-detector distances. The analysis method discussed in this article can be helpful in optimizing the setup of X-ray in-line phase-contrast imaging.

X-ray diffraction imaging self-detected with a CCD

Self-detection of x-ray diffraction has been accomplished by measuring the electrical behaviour of a semiconductor single-crystal of a commercial detector when it is in and out of the x-ray diffraction condition. A decrease in the photocurrent or in the photocounting is measured when the detector is set in the diffraction condition. The self-detection of x-ray diffraction was imaged using a CCD detector diffracting the Si(400) in a non-dispersive set-up with an external monochromator. The depletion layer of the CCD is about 30 µm thick, which makes it a finite crystal for the energies used in terms of the dynamical theory of x-ray diffraction. The profile, referred to here as the anti-h peak, was obtained from images taken at different diffraction angular positions of the CCD. These profiles are in agreement with those calculated for finite crystals. An application of this effect, where the CCD is used as a detector and an analyser crystal in an analyser-based x-ray phase contrast imaging set-up, is realized here. It could be useful for Multiple Imaging Radiography and related mathematical image processing with the Schlieren method.

Preliminary studies of enhanced contrast radiography in anatomy and embryology of insects with Elettra synchrotron light

Enhanced contrast X-ray imaging is achieved by exploiting the real part of the refraction index, which is responsible for the phase shifts, in addition to the imaginary part, which is responsible for the absorption. Such techniques are called X-ray phase contrast imaging. An analyzer-based X-ray phase contrast imaging set-up with Diffraction Enhanced Imaging processing (DEI) were used for preliminary studies in anatomy and embryology of insects. Parasitized stinkbug and moth eggs used as control agents of pests in vegetables and adult stinkbugs and mosquitoes ( Aedes aegypti) were used as samples. The experimental setup was mounted in the SYRMEP beamline at ELETTRA. Images were obtained using a high spatial resolution CCD detector (pixel size 14×14 μ m 2) coupled with magnifying optics. Analyzer-based X-ray phase contrast images (PCI) and edge detection images show contrast and details not observed with conventional synchrotron radiography and open the possibility for future study in the embryonic development of insects.