Wind Power Conversion System Research Articles

New design of robust controller based on fuzzy 12 linguistic variables for wind power conversion system

New design of robust controller based on fuzzy 12 linguistic variables for wind power conversion system

Performance of Robust Type-2 Fuzzy Sliding Mode Control Compared to Various Conventional Controls of Doubly-Fed Induction Generator for Wind Power Conversion Systems

This paper presents a novel hybrid type-2 fuzzy sliding mode control approach for regulating active and reactive power exchanged with the utility grid by a doubly-fed induction generator in a wind energy conversion system. The main objective of this hybridization is to eliminate the steady-state chattering phenomenon inherent in sliding mode control while improving the transient delays caused by type-2 fuzzy controllers. In addition, the proposed control approach has proven to be successful in coping with varying generator parameters and exhibited good reference tracking. An in-depth comparative study with state-of-the-art advanced control techniques is also the focus of the present paper. The comparative study has three objectives, namely: a qualitative comparative study that aims to compare response times and reference tracking capabilities; a quantitative evaluation that takes into account time-integrated performance criteria; and finally, robustness capabilities. The simulation results, carried out in the Matlab/Simulink environment, have demonstrated the effectiveness and best performance of the proposed hybrid type-2 fuzzy sliding mode control with respect to other advanced techniques included in the comparison study.

Advanced control scheme of doubly fed induction generator for wind turbine using second sliding mode control

This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator(DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC).Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.

Ziegler-Nichols Based Controller Optimization for DFIG Wind Turbines

Wind power conversion systems are becoming the most preferable alternate renewable energy source. Doubly Fed Induction Generator’s utilization rotating parts in wind turbines is increasing with the wind power penetration to the electric grid. The observation becomes more noticeable when there are abnormal conditions within the electrical power system. In this paper, MPPT Controller is incorporated with DFIG through the MATLAB Simulink program is simulated. A conventional PI controller is tuned with Ziegler-Nichol’s (Z-N) method and was implemented to the DFIG Control Block. The rotor-side converter (RSC) is utilized to regulate the power generated by the doubly-fed induction generator (DFIG), while the direct current (DC) bus voltage is controlled by the grid-side converter (GSC). The DFIG's angular and comparative angular speeds are used to generate the reference torque value in the MPPT controller. This improved the time response, output power, electromotive torque, and other current and voltage characteristics. A comparison was made between the output evaluation of the inbuilt controller and the output evaluation of the proposed controller. The MPPT with tuned PI Controller's results show that the suggested system, which uses DFIG coupled to a rotor, is accurate, dependable, and feasible. DOI: https://doi.org/10.52783/tjjpt.v45.i02.6966

A new-fangled connection of UPQC tailored power device from wind farm to weak-grid

A significant portion of wind power conversion systems worldwide comprise wind farms (WFs) that use Squirrel Cage Induction Generator (SCIG) and are directly linked to the power grid. In facilities that generate electrical energy at a moderate level, WFs are connected by means of distribution systems that use medium voltage (MV). It is not uncommon for such a system to produce a scenario in which the amount of electricity generated corresponds to the grid’s transit volume. When a wind farm’s wind power generation system is connected to a weak grid, the lack of potential control of the Point of Common Coupling (PCC) is a primary issue. This strategy is called a “Wind Farm with Weak Grid Connection.” Therefore, the amalgamation of weak grids, fluctuating electricity from wind, and variations in load on the system cause disruptions in the PCC voltage, further degrading the Power Quality (PQ) and the WF stability. Either the control method at the production level or the compensating strategies at the PCC level can improve this situation. If wind farms are built on SCIG and are directly linked to the grid, it is essential to utilise the last substitute. The technology known as Custom Power Devices (CUPS), proved extremely helpful for this type of application. This study presents a compensation technique based on a specific CUPS device, known as the Unified Power Quality Compensator (UPQC), as a possible solution. The potential terminals of WF needed to be regulated, and the voltage fluctuations on the grid side required to be reduced, so a custom-made control strategy for the UPQC device was designed internally. The control of power, such as active and reactive in the UPQC’s series and shunt converters, as well as the transmission of power via the UPQC DC-Link between converters, are the foundation of the internal control strategy that has been developed. Compared to other bespoke tactics that use reactive power, this strategy increases the UPQC’s capability to provide compensation. The suggested study calculates THD using a FUZZY controller. The results are compared to PI controller results. Simulation findings show how the suggested compensating strategy can minimise THD values and improve wind farm power and stability. The simulations suggest that the proposed compensating strategy enhances WF power and stability.

A novel intelligent control approach for wind energy conversion systems with synchronous reluctance generators

SummaryThis study addresses a significant research gap in the field of wind energy, focusing on the underutilized potential of synchronous reluctance generators (SynRG) in wind power conversion systems (WPCS). Despite notable advancements in wind energy controls, the capabilities of SynRG within these systems have not been fully explored. In response, we introduce an innovative model‐free control (MFC) approach, termed intelligent proportional (iP), specifically designed and optimized for WPCS equipped with SynRG. This research encompasses the modeling, control, and simulation of SynRG‐based WPCS, aiming to optimize system performance and enhance the quality of grid power supply. The proposed vector control (VC) method utilizes a MFC approach (VC‐iP) to address the limitations inherent in traditional VC methods with proportional‐integral (PI) controllers (VC‐PI). Although widely used for their simplicity, VC‐PI methods often lead to power fluctuations and decreased power and current quality, consequently reducing overall system efficiency. In contrast, VC‐iP markedly enhances power quality and system efficiency, especially in situations involving fluctuating power demand and variable wind speeds. The efficacy of VC‐iP is demonstrated through simulations in two distinct test scenarios that include variations in power demand and random wind speed fluctuations. The results affirm the superiority of VC‐iP in maintaining stable, high‐quality power output from WPCS. This method notably minimizes fluctuations, improves current quality, reduces harmonic distortion and steady‐state error, ensures reliable grid integration, and contributes to a more efficient and sustainable energy system.

Robust Control System for DFIG-Based WECS and Energy Storage in reel Wind Conditions

This research work focuses on addressing the challenges of controlling a wind energy conversion system (WECS) connected to the grid, particularly when faced with variable wind speed profiles. The system consists of a Doubly-Fed Induction Generator (DFIG) connected to the grid through an AC/DC/AC converter, along with a Li-ion battery storage system connected to the Back-to-Back converter DC link via a DC/DC converter. The non-linearity and internal parametric variation of the wind turbine can negatively impact energy production, battery charging performance, and battery lifespan. To overcome these issues, the study proposes a robust control approach called Integral action Sliding Mode Control (ISMC) to enhance the dynamic performance of the WECS based on DFIG. Additionally, the battery charging and discharging controllers play a crucial role in efficiently distributing power to the grid and storage unit based on the battery's state of charge, extracted energy, and power injected into the grid. Two current regulation modes, buck charging and boost discharging, are employed to ensure proper energy distribution. Furthermore, a storage system energy management algorithm is implemented to ensure battery safety during one of the charging modes. The effectiveness and robustness of the proposed control method were validated through simulations of a 1.5 MW wind power conversion system using Matlab/Simulink. The results confirmed the method's efficiency and efficacy.

Controlling PMSG Wind Turbine Connected to Three Level Neutral Point Clamped Inverter Based on MPC

Wind energy generation systems are facing increasing importance in terms of harmonic distortion control and power quality standards. In recent years, variable speed has also risen rapidly due to advancements in power electronics. The three key elements of a wind power conversion system (WECS) are electrical generators, machine-side converters, and grid-side converters. It should be noted that the permanent magnet synchronous generator is one of the most often used types of electrical generators due to its special qualities. When wind energy is converted to the proper electrical power, it may be injected into the utility grid using either synchronous generators or grid-side converters. Therefore, an investigation of several topologies and control strategies is required to determine which is the best for the machine-side converter. The use of model predictive control (MPC) for a surface mount permanent magnet synchronous machine wind turbine is the main topic of this work. The machine's electrical model is the one that was utilized. The power converters are selected considering the intricate and highly nonlinear aerodynamic system of the wind turbines. MPC is a promising control technique despite being a relatively recent application in power electronics. In addition, MATLAB and Simulink are used to build the MPC code and offer a simplified model of the turbine.

Implementation of third-order sliding mode for power control and maximum power point tracking in DFIG-based wind energy systems

In the field of generation systems, system performance, and power quality are greatly affected by traditional control techniques based on proportional-integral (PI) controllers, which are affected by internal and external factors. Wind power conversion systems based on doubly-fed induction generators are exposed to certain nonlinearities, uncertainties, and external disturbances. From another side, the extraction of the mechanical wind energy required a high-performance control system. This study proposes a robust nonlinear chattering-free third-order sliding mode control (TOSMC) based power control applied to fix its primary disadvantages which are the chattering phenomena and active and reactive power ripples. To show the potential of the proposed TOSMC control, a comparison study considering the TOSMC control, traditional sliding mode control, and the other existing controls is done in terms of power ripples, harmonic distortion of stator current, robustness, and response time. To ensure maximum power extractions and to protect the system, the maximum point power tracking technique based on TOSMC and the proposed control are also implemented. In addition, These techniques are used to control the stator powers. Finally, simulations (using Matlab software) are performed using different wind speeds with durability testing. The simulated results show that the proposed TOSMC control with the MPPT-TOSMC technique in this paper achieves satisfactory results in terms of reducing power ripples, response time, and harmonic distortion of stator current compared to the sliding mode control, where the harmonic distortion reduction ratio of the current was (50.24%) and the active power ripple reduction ratio (47.50%) and the reactive power (46.68%).

Enhancing Single-Phase Grid Integration Capability of PMSG-Based Wind Turbines to Support Grid Operation under Adverse Conditions

The proposed work delivers a robust control solution for a single-phase permanent magnet synchronous generator-based wind power conversion system (PMSG-WPCS) to enhance grid integration capability. The proposed control approach also offers an extended facility to fulfill low-voltage fault ride-through (LVRT) requirements under adverse grid conditions. Unlike the conventional observer-based PLL (O-PLL) approach, the proposed improved Lyapunov theory-based prefilter (ILP) is helpful in yielding a quadrature signal to solve the single-phase grid synchronization problem. Moreover, the proposed prefilter can leverage delayed signal operation, which improves the harmonic and the DC-offset component rejection abilities while eliminating the need for internal feedback-based submodule blocks for the case of an O-PLL. Consequently, the proposed ILP-PLL exhibits better dynamic behavior to rapidly synchronize a grid-tied power converter and can accurately track the fundamental amplitude information that is required for inverter control to meet the fault ride-through requirements. In addition, the suggested LVRT controller ensures smooth transition between the unity and non-unity power factor modes for superior converter control over reactive current injection into the grid to recover the grid from faults while maintaining a lower amount of total harmonic current distortions. The dynamic performance of the proposed control scheme is experimentally validated in view of the existing O-PLL approach for lower-rating wind-turbine-based PMSG-WPCS.

Fault diagnosis of wind turbine power converter using intrinsic mode functions with relative energy entropy

PurposeThe purpose of this paper is to prevent the destruction of other parts of a wind energy conversion system because of faults, the diagnosis of insulated-gate bipolar transistor (IGBT) faults has become an essential topic of study. Demand for sustainable energy sources has been prompted by rising environmental pollution and energy requirements. Renewable energy has been identified as a viable substitute for conventional fossil fuel energy generation. Because of its rapid installation time and adaptable expenditure for construction scale, wind energy has emerged as a great energy resource. Power converter failure is particularly significant for the reliable operation of wind power conversion systems because it not only has a high yearly fault rate but also a prolonged downtime. The power converters will continue to operate even after the failure, especially the open-circuit fault, endangering their other parts and impairing their functionality.Design/methodology/approachThe most widely used signal processing methods for locating open-switch faults in power devices are the short-time Fourier transform and wavelet transform (WT) – based on time–frequency analysis. To increase their effectiveness, these methods necessitate the intensive use of computational resources. This study suggests a fault detection technique using empirical mode decomposition (EMD) that examines the phase currents from a power inverter. Furthermore, the intrinsic mode function’s relative energy entropy (REE) and simple logical operations are used to locate IGBT open switch failures.FindingsThe presented scheme successfully locates and detects 21 various classes of IGBT faults that could arise in a two-level three-phase voltage source inverter (VSI). To verify the efficacy of the proposed fault diagnosis (FD) scheme, the test is performed under various operating conditions of the power converter and induction motor load. The proposed method outperforms existing FD schemes in the literature in terms of fault coverage and robustness.Originality/valueThis study introduces an EMD–IMF–REE-based FD method for VSIs in wind turbine systems, which enhances the effectiveness and robustness of the FD method.

Transient stability enhancement using optimized PI tuning of static synchronous series compensator in wind power conversion system

Power systems are expanding comprehensively with the increase in load demand from both residential and industrial usage. Renewable energy is penetrating the power system to satisfy the power needs of the load demand. With its potential to generate power and compensate for a large portion of the load demand, wind generators make a major renewable power contribution. Power oscillations inherent in wind generator integration with the grid are a power quality issue to be addressed. Oscillation damping using flexible AC transmission system (FACTS) devices is a relevant solution for the power quality issue. There are multiple reasons for power oscillation. Mainly, power systems encounter fault conditions. The faults can be cleared, and the power system tries to retain stability. Sometimes, the system fails due to a longer settling time. A series-connected FACTS device utilized as a series compensator is referred to as a static synchronous series compensator (SSSC). Controlling the flow of electricity over a transmission line using this method is incredibly efficient. The capacity to switch between a capacitive and an inductive reactance characteristic is necessary. The SSSC regulates the flow of power in transmission lines to which it is linked by adjusting both the magnitude of the injected voltage and the phase angle of the injected voltage in series with the transmission line. This allows the SSSC to manage the power flow in the transmission lines. It does it by inserting a voltage that can be controlled into a transmission line in series with the fundamental frequency. This paper develops the optimally tuned SSSC in the wind-integrated grid system to dampen the oscillation. Teacher–learner-based optimization (TLBO) and gray wolf optimization (GWO) algorithms are used to tune the PI controller to improve the damping response. The obtained results show that the damping performance of the proposed controller is better than that of the other traditional controllers.

SSR Stable Wind Speed Range Quantification for DFIG-Based Wind Power Conversion System Considering Frequency Coupling

The subsynchronous resonance (SSR) characteristics of doubly-fed induction generation-based wind power conversion system (DFIG-WPCS) varies with the wind speed. Obtaining the small signal SSR stable wind speed range is urgently important for wind farm dispatch planning. However, there are few methods to quantify the small signal SSR stable wind speed range of DFIG-WPCS. Moreover, the inherent frequency coupling when DFIG-WPCS is integrated to modular multilevel converter-high voltage direct current (MMC-HVDC) may lead to inaccurate stability assessment results. In this article, the frequency coupling mechanism between WPCS and MMC is revealed by analyzing the law of harmonic interaction in the interconnected system. The wind speed-frequency two-variable equivalent admittance model of DFIG-WPCS is established by taking the frequency coupling account. Relying on the two-variable open-loop transfer function, the multiple phase margin contours plot approach is proposed to quantify the small signal SSR stable wind speed range and damping properties. The effectiveness of two-variable admittance and analysis method are validated against electromagnetic transient (EMT) testbed with MATLAB /SimPowerSystems. The analysis results can provide a reference for the early planning and stable operation of DFIG-WPCS.

A Review on Popular Control Applications in Wind Energy Conversion System Based on Permanent Magnet Generator PMSG

There has always been a high expectation that wind generation systems would capture maximum power and integrate properly with the grid. Utilizing a wind generation system with increased management to meet the growing electricity demand is a clever way of accomplishing this. However, wind power generation systems require a sophisticated, unique, and dependable control mechanism in order to achieve stability and efficiency. To improve the operation of the wind energy conversion method, researchers are continually addressing the obstacles that presently exist. Therefore, it is necessary to know which control can improve the whole system’s performance and ensure its successful integration into the network, despite the variable conductions. This article examines wind turbine control system techniques and controller trends related to the permanent magnet synchronous generator. It presents an overview of the most popular control strategies that have been used to control the PMSG wind power conversion system. Among others, we mention nonlinear sliding mode, direct power, backstepping and predictive currents control. First, a description of each control is presented, followed by a simulation performed in the Matlab/Simulink environment to evaluate the performance of each control in terms of reference tracking, response time, stability and the quality of the signal delivered to the network under variable wind conditions. Finally, to get a clear idea of the effect of each control, this work was concluded with a comparative study of the four controls.

Explicit damping specification in PI controller design for desired control performance of wind power conversion system with permanent magnet generator

Explicit damping specification in PI controller design for desired control performance of wind power conversion system with permanent magnet generator

A 2 MW Wind Turbine Simulator for DFIG Wind Energy Generation Systems

This work presents the design and implementation of a wind turbine simulator to carry out laboratory tests on the generation, regulation, and control of a wind power conversion system (WECS) with a capacity of 2 MW. A three-phase squirrel-cage induction motor emulates the static and dynamic wind turbine characteristics based on the torque-speed profile of a wind turbine. The Emulator allows all electromechanical tests to be carried out, from the characterization of the generator to the adjustment of controls and protections for equipment operating in a specific location. Initial Emulator tests were successful. This simulator aims to reproduce the same behavior as a wind turbine, that is, the generator must operate as if it were connected to a real turbine. In this line, a wind profile implemented by using a computer program and its output is used as an input signal. This signal together with the speed measured on the axis serves as the input variable of the emulated turbine.

Increasing energy efficiency of counter-rotating wind turbines by experimental modelling

With the significant advance in exploiting wind energy, there has been a shift in research from the study of conventional systems to the study of counter-rotating systems due to additional energy input of the second rotor. The paper presents the results of the research on achieving an increase in the energy efficiency of counter-rotating wind power conversion systems. For this purpose, there have been designed different sizes of wind rotors, were 3D printed and tested in an open-circuit aerodynamic tunnel for different wind velocities and axial distances between rotors. The constructive design consisting of a smaller diameter front rotor and a larger rear rotor was chosen. The individual wind rotors were used to configure two experimental models of counter-rotating wind systems. The testing results analysis and interpretation enabled the establishing of the design and operating conditions that provide the highest power extracted from wind at 10 m/s velocity. A higher efficiency of the wind turbine system is achieved for a lower ratio between the front and rear turbines. In the case of the analysed experimental models, an increase in system efficiency of 49.14% is achieved for a 0.845 diameter ratio, and of 39.02% for 0.945 diameter ratio, respectively.

The main types of wind turbines-generators in the power supply system

PURPOSE. Conduct a detailed analysis of existing wind turbines. Analyze the role, place and features of the functioning of wind power plants. Provide various options for generators and schemes for converting wind energy into electricity. Provide recommendations for improving the reliability of wind turbines in smart grids.METHODS. The article was prepared using analytical methods, statistical, theoretical, factorial and technical methods.RESULTS. A fixed speed asynchronous generator used in a wind power conversion system (WECS) without a power converter interface draws a significant portion of the reactive power from the grid. This configuration features simple, reliable operation. Wind turbine asynchronous generator with dual power supply. can improve overall power conversion efficiency by performing maximum power point tracking (MPPT), and an increase in speed of about 30% can improve dynamic performance and increase resilience to system disturbances that are not available for turbine types 1 and 2. The use of full-scale 100% power converters will significantly increase the productivity of SPEV wind energy conversion systems, but will slightly increase the cost of the power converter, up to 7% - 12% of the total equipment cost. By using a large number of pole pairs for all types of permanent magnet synchronous generator (PMG), the turbine gearbox can be removed. This type of wind energy conversion system is more resilient to grid disruptions compared to type 1, 2 and 3 wind systems. The review shows that types 3 and 4 technologies are used to most efficiently sell and recycle wind turbines in electricity markets.CONCLUSION. The article analyzes the features of the functioning of wind power plants operating on the grid. Various options for generators and schemes for converting wind energy into electricity are presented. A detailed analysis of existing wind turbines is provided. Recommendations are given for improving the reliability and efficiency of wind power plants in smart grids.

PMSG Based Wind Energy Conversion System Using Intelligent MPPT with HGRSC Converter

Wind power conversion systems play a significant position in grid-coupled renewable source networks. In this paper, a permanent magnet based synchronous alternator type wind energy scheme is considered for analysis. The enhanced performance of wind power conversion could be reached by improving maximum power point tracking (MPPT) and by modernising the control circuit of the power electronic circuit. The main task is to enrich its performance level by proposing fuzzy gain scheduling (FGS) based optimal torque management for maximum power point tracking. In addition to the improved MPPT, this article analyses different topologies of direct current–direct current (DC–DC) converters such as boost converter and high-gain resonant switched capacitor converter. Comparative simulation analysis of converters with conventional optimal torque control and proposed FGS-based optimal torque control using MATLAB/simulink are presented with various wind speeds.

Direct Power and Voltage Oriented Control Strategies of Grid-Connected Wind Energy Conversion System Based on Permanent Magnet Synchronous Generator

This article deals with the control techniques of a low-voltage grid-connected to wind power conversion system based on a permanent magnet synchronous generator (PMSG) using an indirect matrix converter (IMC). Details of the proposed strategies for both the rectifier and inverter stages of the IMC are presented. Thus, a rectifier control strategy based on voltage-oriented control using space vector modulation is proposed. In addition, the control objective of the direct power control (DPC) inverter is the regulation of the active powers of the PMSG according to references established on the basis of the maximum power point tracker (MPPT) of the wind turbine, and also a good tracking of the output reactive power to its reference ensures unit power factor (UPF). A numerical simulation investigation is conducted to investigate the fast-dynamic performance of the proposed control systems during the wind speed variation. The obtained results in simulation are then complemented with tests in laboratory environment, the DPC control system is implemented on a dSpace DS1104 real time board. Selective experimental results are presented using a laboratory prototype of the wind energy conversion system to demonstrate the resulting improvements of the developed system. The results achieved have been clearly responded to the follow-up of references even under fluctuating wind conditions, and show promising relevance of the proposed method.