Wideband Integrated Bioaerosol Sensor Research Articles

Assessing Characteristics and Variability of Fluorescent Aerosol Particles: Comparison of Two Case Studies in Southeastern Italy Using a Wideband Integrated Bioaerosol Sensor

Assessing Characteristics and Variability of Fluorescent Aerosol Particles: Comparison of Two Case Studies in Southeastern Italy Using a Wideband Integrated Bioaerosol Sensor

Human emissions of size-resolved fluorescent bioaerosols in control situations

Human bioaerosols contribute significantly to indoor air quality. This study used a Wideband Integrated Bioaerosol Sensor (WIBS-4A) instrument for real-time measurement of particle size distribution and count to differentiate fluorescent bioaerosols from non-fluorescent aerosols. Through an experiment involving 12 subjects (six men and six women) wearing standard cotton clothing in a 2 m × 2 m × 2 m environmental chamber, we established a quantitative method to obtain the bioaerosol emission rate of a single subject, aiming to explore the effects of masks and sex on bioaerosol emissions from different individuals. The mean emission rates of fluorescent bioaerosols in the particle size ranges of 0.5–2.5 μm and 2.5–10 μm were 3.192±2.11×104 counts/(person·h) and 13.98±9.34×104 counts/(person·h), respectively. A comparison between those wearing and not wearing masks revealed no significant differences in the emissions of fluorescent bioaerosols. This suggests respiratory sources may not significantly impact the emissions of fluorescent bioaerosols from individuals under seated breathing conditions. Significant disparities in the fluorescent bioaerosol emission rates of different biological sexes were observed through independent sample analysis. Males exhibited 41 % and 15 % higher emission rates than females for particle size ranges of 0.5–2.5 μm and 2.5–10 μm, respectively, possibly because of different metabolic rates. A significant correlation between metabolic rates and fluorescent bioaerosols (sig = 0.044 < 0.05) was observed in all the subjects. These findings underscore the individual variations that affect bioaerosol emission rates. The data provided by this study will facilitate further analysis of the on-site measured data and source analysis.

A fluorescence approach for an online measurement technique of atmospheric microplastics.

Microplastic particles in the atmosphere are regularly detected in urban areas as well as in very remote locations. Yet the sources, chemical transformation, transport, and abundance of airborne microplastics still remain largely unexplained. Therefore, their impact on health, weather and climate related processes lacks comprehensive understanding. Single particle detection presents a substantial challenge due to its time-consuming process and is conducted solely offline. To get more information about the distribution, fluxes and sources of microplastics in the atmosphere, a reliable and fast online measurement technique is of utmost importance. Here we demonstrate the use of the autofluorescence of microplastic particles for their online detection with a high sensitivity towards different widely used polymers. We deploy online, single particle fluorescence spectroscopy with a Wideband Integrated Bioaerosol Sensor WIBS 5/NEO (Droplet Measurement Technologies, USA), which enables single particle fluorescence measurements at two excitation wavelengths (280 nm and 370 nm) and in two emission windows (310-400 nm and 420-650 nm). We investigated shredded (<100 μm) everyday plastic products (drinking bottles and yogurt cups) and pure powders of polyethylene terephthalate (PET), polyethylene and polypropylene. For the broad range of typical plastic products analyzed, we detected fluorescence on a single particle level using the WIBS. The online detection can identify particles smaller than 2 μm. In the case of microplastic particles from a PET bottle, 1.2 μm sized particles can be detected with 95% efficiency. Comparison with biological aerosols reveals that microplastics can be distinguished from two abundant pollen species and investigation of the complete fluorescence excitation emission maps of all samples shows that online identification of microplastics might be possible with fluorescence techniques if multiple channels are available.

Evaluation of a method to quantify the number concentrations of submicron water-insoluble aerosol particles based on filter sampling and complex forward-scattering amplitude measurements

Water-insoluble aerosol particles (WIAPs), such as black carbon (BC), mineral dust, and primary biological aerosol particles (PBAPs), affect climate through their interaction with radiation and clouds. However, with the exception of BC, methods to identify WIAP types and quantify their number concentrations are limited. Here, we evaluated a method that has been recently developed to measure the number concentrations of submicron WIAPs based on atmospheric aerosol measurements at an urban site in Nagoya, Japan. In this method, atmospheric aerosol particles are collected on a filter and dispersed in water. Then, the complex forward-scattering amplitudes of individual particles are measured. This complex parameter reflects the complex refractive index, volume, and shape of each measured particle, enabling the characterization of these physical properties from the signals. The WIAPs were classified as BC-like, dust-like, and PBAP-like particles based on their complex amplitude data. The number concentrations of BC-like particles were strongly correlated with those of refractory BC particles measured by a Single Particle Soot Photometer. BC-like and dust-like particles dominated the population of the submicron WIAPs, which was also confirmed using electron microscopy and Wideband Integrated Bioaerosol Sensor observations. Under the observed atmospheric conditions, the number concentrations of WIAPs were measured with their dispersion efficiency from a filter to water of approximately 50%. These results indicate that our method based on filter sampling and complex forward-scattering amplitude measurements has the potential to become a new technique for quantifying the spatio-temporal distributions of WIAPs.

Assessment of indoor bioaerosol exposure using direct-reading versus traditional methods—potential application to home health care

Home healthcare workers (HHCWs) can be occupationally exposed to bioaerosols in their clients’ homes. However, choosing the appropriate method to measure bioaerosol exposures remains a challenge. Therefore, a systematic comparison of existing measurement approaches is essential. Bioaerosol measurements with a real-time, fluorescence-based Wideband Integrated Bioaerosol Sensor (WIBS) were compared to measurements with four traditional off-line methods (TOLMs). The TOLMS included optical microscopic counting of spore trap samples, microbial cultivation of impactor samples, qPCR, and next-generation sequencing (NGS) of filter samples. Measurements were conducted in an occupied apartment simulating the environments that HHCWs could encounter in their patients’ homes. Descriptive statistics and Spearman’s correlation test were computed to compare the real-time measurement with those of each TOLM. The results showed that the geometric mean number concentrations of the total fluorescent aerosol particles (TFAPs) detected with the WIBS were several orders of magnitude higher than those of total fungi or bacteria measured with the TOLMs. Among the TOLMs, concentrations obtained with qPCR and NGS were the closest to the WIBS detections. Correlations between the results obtained with the WIBS and TOLMs were not consistent. No correlation was found between the concentrations of fungi detected using microscopic counting and any of the WIBS fluorescent aerosol particle (FAP) types, either indoors or outdoors. In contrast, the total concentrations detected with microbial cultivation correlated with the WIBS TFAP results, both indoors and outdoors. Outdoors, the total concentration of culturable bacteria correlated with FAP-type AC. In addition, fungal and bacterial concentrations obtained with qPCR correlated with FAP types AB and AC. For a continuous, high-time resolution but broad scope, the real-time WIBS could be considered, whereas a TOLM would be the best choice for specific and more accurate microbial characterization. HHCWs’ activities tend to re-aerosolize bioaerosols causing wide temporal variation in bioparticle concentrations. Thus, the advantage of using the real-time instrument is to capture those variations. This study lays a foundation for future exposure assessment studies targeting HHCWs.

A Modified Spectroscopic Approach for the Real-Time Detection of Pollen and Fungal Spores at a Semi-Urban Site Using the WIBS-4+, Part I.

The real-time monitoring of primary biological aerosol particles (PBAP) such as pollen and fungal spores has received much attention in recent years as a result of their health and climatic effects. In this study, the Wideband Integrated Bioaerosol Sensor (WIBS) 4+ model was evaluated for its ability to sample and detect ambient fungal spore and pollen concentrations, compared to the traditional Hirst volumetric method. Although the determination of total pollen and fungal spore ambient concentrations are of interest, the selective detection of individual pollen/fungal spore types are often of greater allergenic/agricultural concern. To aid in this endeavour, modifications were made to the WIBS-4 instrument to target chlorophyll fluorescence. Two additional fluorescence channels (FL4 and FL5 channels) were combined with the standard WIBS channels (FL1, FL2, FL3). The purpose of this modification is to help discriminate between grass and herb pollen from other pollen. The WIBS-4+ was able to successfully detect and differentiate between different bioaerosol classes. The addition of the FL4 and FL5 channels also allowed for the improved differentiation between tree (R2 = 0.8), herbaceous (R2 = 0.6) and grass (R2 = 0.4) pollen and fungal spores (R2 = 0.8). Both grass and herbaceous pollen types showed a high correlation with D type particles, showing strong fluorescence in the FL4 channel. The additional fluorescent data that were introduced also improved clustering attempts, making k-means clustering a comparable solution for this high-resolution data.

Biological and Nonbiological Sources of Fluorescent Aerosol Particles in the Urban Atmosphere.

Online detection of bioaerosols based on the light-induced fluorescence (LIF) technique is still challenging due to the complexity of bioaerosols and the external/internal mixing with nonbiological fluorescent compositions. Although many lab studies have measured the fluorescence properties of the biological and nonbiological materials, there is still a scarcity of knowledge of the sources of fluorescent aerosol particles (FAP) in the ambient atmosphere. Here, we fill this gap by combining the online measurement of an LIF-based instrument (wideband integrated bioaerosol sensor, WIBS, 0.8-20 μm) with the measurements of typical biological matter and the compositions related to major nonbiological FAP from May to July in the megacity Beijing. We find that fungal spores and pollen are widely observed in all types of FAP using a WIBS. Bacteria are suggested to be associated with the fine mode FAP (excitation/emission: 280 nm/310-400 nm; 0.8-3 μm). The FL-B and -BC particles (emission in 420-650 nm) contributing the most to FAP are strongly associated with humic-like substances, dust, burning and combustion emissions, and secondary organic aerosols (SOA). This study provides a guide for interpreting individual FAP measured by LIF instruments and points to the applicability of online LIF instruments to characterize nonbiological compositions including SOA.

Observation of bioaerosol transport using wideband integrated bioaerosol sensor and coherent Doppler lidar

Abstract. Bioaerosols are usually defined as aerosols arising from biological systems such as bacteria, fungi, and viruses. They play an important role in atmospheric physical and chemical processes including ice nucleation and cloud condensation. As such, their dispersion affects not only public health but also regional climate. Lidar is an effective technique for aerosol detection and pollution monitoring. It is also used to profile the vertical distribution of wind vectors. In this paper, a coherent Doppler wind lidar (CDWL) is deployed for aerosol and wind detection in Hefei, China, from 11 to 20 March in 2020. A wideband integrated bioaerosol sensor (WIBS) is used to monitor variations in local fluorescent bioaerosols. Three aerosol transport events are captured. The WIBS data show that, during these transport events, several types of fluorescent aerosol particles exhibit abnormal increases in their concentration, number fractions to total particles, and number fractions to whole fluorescent aerosols. These increases are attributed to external fluorescent bioaerosols instead of local bioaerosols. Based on the HYbrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) backward trajectory model and the characteristics of external aerosols in WIBS, their possible sources, transport paths, and components are discussed. The results prove the influence of external aerosol transport on local high particulate matter (PM) pollution and fluorescent aerosol particle composition. The combination of WIBS and CDWL expands the aerosol monitoring parameters and provides a potential method for real-time monitoring of fluorescent biological aerosol transport events. In addition, it also helps to understand the relationships between atmospheric phenomena at high altitudes like virga and the variation of surface bioaerosol. It contributes to the further understanding of long-range bioaerosol transport, the roles of bioaerosols in atmospheric processes, and in aerosol–cloud–precipitation interactions.

Real-time Monitoring of Aerosol Generating Dental Procedures

ObjectiveWe aimed to quantify aerosol concentrations produced during different dental procedures under different mitigation processes. MethodAerosol concentrations were measured by the Optical Particle Sensor (OPS) and Wideband Integrated Bioaerosol Sensor (WIBS) during routine, time-recorded dental procedures on a manikin head in a partitioned enclosure. Four different, standardised dental procedures were repeated in triplicate for three different mitigation measures. ResultBoth high-volume evacuation (HVE) and HVE plus local exhaust ventilation (LEV) eradicated all procedure-related aerosols, and the enclosure stopped procedure-related aerosols escaping. Aerosols recorded by the OPS and WIBS were 84 and 16-fold higher than background levels during tooth 16 FDI notation (UR6) drilling, and 11 and 24-fold higher during tooth 46 FDI notation (LR6) drilling, respectively. Ultrasonic scaling around the full lower arch (CL) or the full upper arch (CU) did not generate detectable aerosols with mitigation applied. Without mitigation the largest concentration of inhalable particles during procedures observed by the WIBS and OPS was during LR6 (139/cm3) and UR6 (28/cm3) drilling, respectively. Brief aerosol bursts were recorded during drilling procedures with HVE, these did not occur with LEV, suggesting LEV provides protection against operator errors. Variation was observed in necessary fallow times (49 – 280 minutes) without mitigation, while no particles remained airborne when mitigation was utilised. ConclusionThis data demonstrates that correctly positioned HVE or LEV is effective in preventing airborne spread and persistence of inhalable particles originating from dental AGPs. Additionally, a simple enclosure restricts the spread of aerosols outside of the operating area. Clinical significanceEmploying correctly positioned HVE and LEV in non-mechanically ventilated clinics can prevent the dispersal and persistence of inhalable airborne particles during dental AGPs. Moreover, using enclosures have the additive effect of restricting aerosol spread outside of an operating area.

Assessing residential indoor and outdoor bioaerosol characteristics using the ultraviolet light-induced fluorescence-based wideband integrated bioaerosol sensor.

We assessed and compared indoor and outdoor residential aerosol particles in a third-floor apartment from August through September 2020. The measurements were conducted using a direct-reading ultraviolet light-induced fluorescence (UV-LIF) wideband integrated bioaerosol spectrometer (WIBS). It measures individual particle light scattering and fluorescence from which particle properties can be derived. The number concentrations of total aerosol particles (TAP) and total fluorescent aerosol particles (TFAP) were significantly higher indoors. Daily and hourly TFAP mean concentrations followed the same trends as the TAP, both indoors and outdoors. The daily mean rank of the TFAP fraction (TFAP/TAP) was significantly higher indoors (23%) than outdoors (19%). Particles representing bacteria dominated indoors while particles representing fungi and pollen dominated outdoors. The mean volume-weighted median diameters for TFAP were 1.67 μm indoors and 2.09 μm outdoors. Higher TFAP fraction indoors was likely due to occupants' activities that generated or resuspended particles. This study contributes to understanding the characteristics of residential aerosol particles in situations when occupants spend most of their time indoors. Based on our findings, a large portion of all indoor aerosol particles could be biological (15-20%) and of respirable particle size (≥95%). Using a novel direct reading UV-LIF-based sensor can help quickly assess aerosol exposures relevant to human health.

Sources, Occurrence and Characteristics of Fluorescent Biological Aerosol Particles Measured Over the Pristine Southern Ocean.

In this study, we investigate the occurrence of primary biological aerosol particles (PBAP) over all sectors of the Southern Ocean (SO) based on a 90‐day data set collected during the Antarctic Circumnavigation Expedition (ACE) in austral summer 2016–2017. Super‐micrometer PBAP (1–16 µm diameter) were measured by a wide band integrated bioaerosol sensor (WIBS‐4). Low (3σ) and high (9σ) fluorescence thresholds are used to obtain statistics on fluorescent and hyper‐fluorescent PBAP, respectively. Our focus is on data obtained over the pristine ocean, that is, more than 200 km away from land. The results indicate that (hyper‐)fluorescent PBAP are correlated to atmospheric variables associated with sea spray aerosol (SSA) particles (wind speed, total super‐micrometer aerosol number concentration, chloride and sodium concentrations). This suggests that a main source of PBAP over the SO is SSA. The median percentage contribution of fluorescent and hyper‐fluorescent PBAP to super‐micrometer SSA was 1.6% and 0.13%, respectively. We demonstrate that the fraction of (hyper‐)fluorescent PBAP to total super‐micrometer particles positively correlates with concentrations of bacteria and several taxa of pythoplankton measured in seawater, indicating that marine biota concentrations modulate the PBAP source flux. We investigate the fluorescent properties of (hyper‐)fluorescent PBAP for several events that occurred near land masses. We find that the fluorescence signal characteristics of particles near land is much more variable than over the pristine ocean. We conclude that the source and concentration of fluorescent PBAP over the open ocean is similar across all sampled sectors of the SO.

Containment of procedure-associated aerosols by an extractor tent: effect on nebulized drug particle dispersal

BackgroundSeveral medical procedures involving the respiratory tract are considered as ‘aerosol-generating procedures’. Aerosols from these procedures may be inhaled by bystanders, and there are consequent concerns regarding the transmission of infection or, specific to nebulized therapy, secondary drug exposure.AimTo assess the efficacy of a proprietary high-efficiency-particulate-air-filtering extractor tent on reducing the aerosol dispersal of nebulized bronchodilator drugs.MethodsThe study was conducted in an unoccupied outpatient room at St. James's Hospital, Dublin, Ireland. A novel real-time, fluorescent particle counter, the Wideband Integrated Bioaerosol Sensor (WIBS), monitored room air continuously for 3 h. Baseline airborne particle count and count during nebulization of bronchodilator drug solutions were recorded.FindingsNebulization within the tent prevented any increase over background level. Nebulization directly into room air resulted in mean fluorescent particle counts of 4.75 x 105/m3 and 4.21 x 105/m3 for Ventolin and Ipramol, respectively, representing more than 400-fold increases over mean background level. More than 99.3% of drug particles were <2 μm in diameter and therefore small enough to enter the lower respiratory tract.ConclusionThe extractor tent was completely effective for the prevention of airborne spread of drug particles of respirable size from nebulized therapy. This suggests that extractor tents of this type would be efficacious for the prevention of airborne infection from aerosol-generating procedures during the COVID-19 pandemic.

Summertime fluorescent bioaerosol particles in the coastal megacity Tianjin, North China

Primary biological particles are an important subset of atmospheric aerosols. They have significant impacts on climate change and public health. Tianjin is a coastal megacity in the North China Plain, which is affected by both anthropogenic activities and marine air masses. To study the abundance and dynamic change of bioaerosols in Tianjin, fluorescent biological aerosol particles (FBAPs) in Tianjin were investigated by a wideband integrated bioaerosol sensor (WIBS-4A) in terms of number concentrations and size distributions in summer (11th –25th August 2018). Meanwhile, total suspended particles were collected and analyzed for chemical compounds to identify potential sources of bioaerosols. WIBS data showed that fluorescent biological particles exhibited two peaks at sunrise (~7:00) and in the evening (~20:00), which were probably caused by the enhancement of fungal spores and bacteria. Three rain events occurred during the observation period. Precipitation enhanced the abundance of biological particles, which were likely released from vegetation leaves, resuspended from soil surfaces, and/or carried by raindrops from high altitudes. The abundance of biological particles showed no significant correlation with Na+ (r = −0.17), indicating the air masses from marine areas carried limited biological particles compared to those from continental areas.

Using flow cytometry and light-induced fluorescence to characterize the variability and characteristics of bioaerosols in springtime in Metro Atlanta, Georgia

Abstract. The abundance and speciation of primary biological aerosol particles (PBAP) is important for understanding their impacts on human health, cloud formation, and ecosystems. Towards this, we have developed a protocol for quantifying PBAP collected from large volumes of air with a portable wet-walled cyclone bioaerosol sampler. A flow cytometry (FCM) protocol was then developed to quantify and characterize the PBAP populations from the sampler, which were confirmed against epifluorescence microscopy. The sampling system and FCM analysis were used to study PBAP in Atlanta, GA, over a 2-month period and showed clearly defined populations of nucleic-acid-containing particles: low nucleic acid-content particles above threshold (LNA-AT) and high nucleic acid-content particles (HNA) likely containing wet-ejected fungal spores and pollen. We find that the daily-average springtime PBAP concentration (1 to 5 µm diameter) ranged between 1.4×104 and 1.1×105 m−3. The LNA-AT population dominated PBAP during dry days (72±18 %); HNA dominated the PBAP during humid days and following rain events, where HNA comprised up to 92 % of the PBAP number. Concurrent measurements with a Wideband Integrated Bioaerosol Sensor (WIBS-4A) showed that fluorescent biological aerosol particles (FBAP) and total FCM counts are similar; HNA (from FCM) moderately correlated with ABC-type FBAP concentrations throughout the sampling period (and for the same particle size range, 1–5 µm diameter). However, the FCM LNA-AT population, possibly containing bacterial cells, did not correlate with any FBAP type. The lack of correlation of any WIBS FBAP type with the LNA-AT suggests that airborne bacterial cells may be more difficult to unambiguously detect with autofluorescence than currently thought. Identification of bacterial cells even in the FCM (LNA-AT population) is challenging, given that the fluorescence level of stained cells at times may be comparable to that seen from abiotic particles. HNA and ABC displayed the highest concentration on a humid and warm day after a rain event (14 April 2015), suggesting that both populations correspond to wet-ejected fungal spores. Overall, information from both instruments combined reveals a highly dynamic airborne bioaerosol community over Atlanta, with a considerable presence of fungal spores during humid days and an LNA-AT population dominating the bioaerosol community during dry days.

Real-time Monitoring of Aerosols Generated from Toilet Flushing

Flushing toilets generate visible droplets from turbulent flow, but also produce numerous smaller airborne droplets (∼micrometres in size) through atomisation. Flushing may aerosolise pathogens from stool or urine, spreading disease. This study continuously monitored aerosols in a shared office lavatory over a week using a biological particle detector, the Wideband Integrated Bioaerosol Sensor (WIBS). This instrument monitors individual particle sizes and numbers and identifies fluorescent particles likely to be droplets containing bacteria. The toilet was a standard wash-down design, (Armitage Shanks), with a lid. No statistically significant variation between fluorescent particle counts was found between periods prior to flushing. Fluorescent particle numbers and intensity increased with toilet flushing, remaining above background for 5 minutes post-flushing on average. Placing the toilet lid down significantly (P&lt;0.001) reduced total and fluorescent particle counts during and after flushing by 30-50%. Lid usage significantly increased (P&lt;0.001) particle diameter from 1.5 μm to 2.1 μm and increased particle fluorescence intensity (P&lt;0.001) during flushing and after flushing, intensity remaining above background for 16 minutes. This suggests standard lid usage reduces but does not eliminate flush-related bioaerosols. Lid-use changes their characteristics and apparently prolongs their residence time in room air. The aerosol change could represent particle agglomeration by a pressure-related Kelvin effect or particle re-aerosolisation from different surfaces in the toilet rather than exclusively originating from droplet generation. Previous studies reporting the effect of toilet lids have found that they prevent the spread of visible droplets on flushing, however the effect on smaller particles is less clear cut.

Model-measurement consistency and limits of bioaerosol abundance over the continental United States

Abstract. Due to low concentrations and chemical complexity, in situ observations of bioaerosol are geographically and temporally sparse, and this limits the accuracy of current emissions inventories. In this study, we apply a new methodology, including corrections for misidentification of mineral dust, to measurements of single particles over four airborne sampling campaigns to derive vertical profiles of bioaerosol over the continental United States. The new methodology is based on single-particle mass spectrometry (SPMS); it can extend historic datasets to include measurements of bioaerosol, it allows comparisons to other techniques, and it generally agrees with a global aerosol model. In the locations sampled, bioaerosols were at least a factor of 10 less abundant than mineral dust. Below 2 km, bioaerosol concentrations were measured between 6×103 and 2×104 m−3. Between 2 and 8 km, bioaerosol concentrations were between 0 and 2×104 m−3, and above 8 km, bioaerosol concentrations were between 0 and 1×103 m−3. Between 30 % and 80 % of single bioaerosol particles detected were internally mixed with dust. A direct comparison of the SPMS methodology with a co-located wideband integrated bioaerosol sensor (WIB) fluorescence sensor on a mountaintop site showed agreement to within a factor of 3 over the common size range.

Investigation of coastal sea-fog formation using the WIBS (wideband integrated bioaerosol sensor) technique

Abstract. A wideband integrated bioaerosol sensor (WIBS-4) was deployed in Haulbowline Island, Cork Harbour, to detect fluorescence particles in real time during July and September 2011. A scanning mobility particle sizer (SMPS) was also installed providing sizing analysis of the particles over the 10–450 nm range. During the campaign, multiple fog formation events occurred; they coincided with dramatic increases in the recorded fluorescent particle counts. The WIBS sizing and fluorescence intensity profiles indicated that the origin of the signals was potentially non-biological in nature (i.e. PBAPs, primary biological aerosol particles). Furthermore, the data did not support the presence of known fluorescing chemical particles like SOA (secondary organic aerosol). Complementary laboratory studies showed that the field results could potentially be explained by the adsorption of molecular iodine onto water droplets to form I2 ⋅ (H2O)x complexes. The release of iodine into the coastal atmosphere from exposed kelp at low tides has been known for many years. This process leads to the production of small IxOy particles, which can act as cloud condensation nuclei (CCN). While the process of molecular iodine release from coastal kelp sources, subsequent particle formation, and the observations of sea mists and fogs have been studied in detail, this study provides a potential link between the three phenomena. Of mechanistic interest is the fact that molecular iodine included into (rather than on) water droplets does not appear to fluoresce as measured using WIBS instrumentation. The study indicates a previously unsuspected stabilizing transport mechanism for iodine in the marine environment. Hence the stabilization of the molecular form would allow its more extensive distribution throughout the troposphere before eventual photolysis.

Abundance and Diurnal Trends of Fluorescent Bioaerosols in the Troposphere over Mt. Tai, China, in Spring

AbstractPrimary biological aerosol particles are ubiquitous in the global atmosphere and can affect cloud formation, deteriorate air quality, and cause human infections. Mt. Tai (1,534 m a.s.l.) is an elevated site in the North China Plain where atmospheric aerosols reflect both regional advection and long‐range transport. In this study, we deployed a Wideband Integrated Bioaerosol Sensor (WIBS‐4A) and collected total suspended particles and eight‐stage size‐segregated aerosol samples at the summit of Mt. Tai in spring from 21 March to 8 April 2017 to quantify the abundance, size distributions, and diurnal variations of fluorescent bioaerosols and to investigate the effect of different fluorescence thresholds of WIBS for ambient bioaerosol recognition. During the whole sampling period, the number concentration of fluorescent particles (&gt;0.8 μm) was 647 ± 533 L−1, accounting for 26.9% ± 10.0% by number of the total particles in that size range. Three‐dimensional excitation‐emission matrix fluorescence of water‐soluble organic matter in size‐segregated aerosols shows that humic‐like substances (HULIS) are mainly in the fine mode (&lt;2.1 μm) while protein‐like substances are mainly in the coarse mode (&gt;2.1 μm). From the diurnal variation, it is shown that bioaerosols can undergo transformation during long‐range transport and contribute to HULIS. For bioaerosol recognition, we find that 6σ‐threshold can lead to better classification of fluorescent aerosol particles for fungal spores. Overall, our results constrain the abundance of primary bioaerosols in the troposphere over East Asia and elucidate the processes for their evolution via mountain/valley breezes and long‐range transport.

Application of remote real-time monitoring of biological airborne particles to characterise different hospital environments

Conventional microbial sampling of air in hospitals is usually carried out using settle plates or impaction air samples. This provides little information about intermittent contamination events and is unhelpful for source attribution. Direct continuous bioaerosol sampling is an established technology used to characterise ambient external air. Portable instruments such as the Wideband Integrated Bioaerosol Sensor (WIBS) combine laser particle size and shape detection with signals of biological origin (fluorescence from amino acids and NAD(P)H) characteristic of viable bioaerosols. Monitoring is continuous for weeks at a time and data collected remotely over the internet. We present evidence of the utility of WIBS analysis in characterising air in hospitals in three different environments: operating theatres (plenum ventilated and ultraclean), a respiratory ward, and a specialist cystic fibrosis outpatients. The airborne particle profile was quantitatively and qualitatively different in each environment. Plumes of biologically-relevant airborne particles were detected and source investigation of failing conventional counts in an operating theatre aided by the continuous record. Nebulised drugs contributed a detectable effect on airborne particles which lasted for several hours on the ward despite air changes. A significant effect of plasma air treatment on airborne particles in the ward was detected by WIBS and not conventional cultures. Continuous monitoring may in future allow objective standard setting for airborne particles in different hospital environments and facilitate rapid detection of airborne infection risks.

A comparison of on-line and off-line bioaerosol measurements at a biowaste site

An air measurement campaign was carried out at a green-waste composting site in the South of Ireland during Spring 2016. The aim was to quantify and identify the levels of Primary Biological Aerosol Particles (PBAP) that were present using the traditional off-line, impaction/optical microscopy method alongside an on-line, spectroscopic approach termed WIBS (Wideband Integrated Bioaerosol Sensor), which can provide number concentrations, sizes and “shapes” of airborne PBAP in real-time by use of Light Induced Fluorescence (LIF). The results from the two techniques were compared in order to validate the use of the spectroscopic method for determining the releases of the wide-range of PBAP present there as a function of site activity and meteorological conditions. The seven-day monitoring period undertaken was much longer than any real-time studies that have been previously performed and allowed due comparison between weekday (working) activities at the site and weekend (closed) releases. The time-span also allowed relationships between site activities like turning, agitation or waste delivery and the WIBS data to be determined in a quantitative manner. This information cannot be obtained with the Andersen Sampling methods generally employed at green-waste management sites. Furthermore, few specific bioaerosol types other than Aspergillus fumigatus, are identified using the traditional protocols employed for site licensing purposes. Here though the co-location of WIBS with the impaction instrument made it possible to identify the real-time release behaviour of a specific plant pathogenic spore, Ustilago maydis, present after green-waste deliveries were made by a local distillery.