Welding Research Articles

Effect of heat input on the microstructure and performance of dissimilar welded joint between Q345B low-alloy steel and 2205 duplex stainless steel

Q345B/2205 dissimilar steel multi-layer multi-pass welded joints were prepared using gas metal arc welding (GMAW). The effects of heat inputs on the microstructures and properties of welded joints were studied. The morphology and composition distribution of Q345B base metal near the fusion line were investigated. The results showed that the welded joints under different heat inputs were all present “carbon depleted zone” and “carburized zones” on both sides of the Q345B base metal and transition layer interface. The microstructure of the “carburized zones” was composed of martensite phase and granular bainite phase. It was found that only the welded joints with heat inputs of 1.765 kJ/mm and 2.860 kJ/mm met the usage requirements. The corrosion behavior and characteristics of the welded joint with a heat input of 1.765 kJ/mm in a 3.5 wt % NaCl solution were investigated intensively. During the soaked process of 14 days, the total impedance value of the welded joint showed first increasing and then decreasing. The maximum value of 8.7 kΩ cm2 was obtained on the 5th day. As the soaked time increased, the corrosion products of the welded joint underwent the formation, thickening, cracking and detachment, which was the main reason of the change in the corrosion resistance. The research results of this article have significant implications for the application of low-alloy steel and stainless steel welded joints in engineering.

Effect of aging state on microstructure and properties of heat affected zone in Al-Mg-Si-Cu alloy welded joints

The softening of the heat affected zone (HAZ) remains a significant challenge in fusion welding of novel Al-Mg-Si-Cu alloy, and the underlying mechanisms vary across different aging states. However, limited research has been conducted on this topic. Therefore, this study investigates the influence of various aging states on the microstructure and mechanical properties within the HAZ of welded joints by selecting extrusions treated with T4, T5, and T6 heat treatments. The results indicate that the increase in hardness of HAZ I is attributed to solid solution strengthening. In the HAZ I, the precipitated phases are mostly dissolved into the matrix under the influence of a peak temperature of 464.6 °C, and no residual precipitated phase is detected in T4 and T5 alloy joints, while some undissolved Q phase is observed in T6 alloy joint. The decrease in hardness of HAZ Ⅱ is attributed to the limited precipitation of coarse β" and Q' phases for the T4 alloy welded joints, which weakens the solid solution strengthening. However, the softening mechanisms in the HAZ Ⅱ of the T5 and T6 alloy joints are ascribed to the dissolution of β" and subsequent precipitation of Q' and Q phases. HAZ Ⅲ, close to the base metal, exhibits a lesser degree of influence and thus experiences a gradual recovery in hardness. This study can provide theoretical guidance for the exploration of high-strength, heat-resistant aluminum alloys.

Achieving microstructural homogeneity in the stir zone across thick AA6061 welds using self-reacting bobbin tool friction stir welding

This study focuses into strategizing the usage of self-reacting bobbin tool friction stir welding (SRBT-FSW) to obtain consistent microstructural homogeneity along the thickness of AA6061 aluminium alloy (AA) thick plates during welding. The SRBT-FSW technology, distinguished by its dual-shoulder design, represents a significant step forward in FSW by eliminating the requirement for a backing anvil and promoting balanced heat distribution. This study seeks to address the issues of maintaining uniform microstructural characteristics throughout the weld zone, which is crucial for the mechanical performance and durability of welded joints in structural applications. The experimental study entails the systematic welding of AA6061 plates of 6 mm thickness using a self-reacting bobbin tool under a fixed processing condition. Electron backscatter diffraction (EBSD) was used to characterize the grain structure and phase distribution over the weld. Mechanical parameters like as tensile strength and hardness were determined to establish correlations between microstructure and mechanical performance. The results demonstrated that SRBT-FSW significantly enhances microstructural homogeneity across the weld zone, leading to improved mechanical properties. In the Bottom Zone (BZ), a refined grain structure with an average grain size (AGS) of 3.53 µm and a random or weak texture was observed, contributing to enhanced hardness and mechanical performance, with an ultimate tensile strength (UTS) of 220 MPa. In contrast, the Top Zone (TZ) exhibited a coarser AGS of 4.33 µm with a pronounced {111} crystallographic texture, resulting in a slightly lower UTS of 205 MPa. The Middle Zone (MZ), influenced by the greater heat input from both the TZ and BZ, showed an intermediate AGS of 3.99 µm, predominantly oriented along the {101} plane, and achieved a UTS of 194 MPa, with a slight reduction in ductility. This study highlights the potential of self-reacting bobbin tool friction stir welding as a reliable method for making high-quality, homogeneous welds in thick aluminium plates and paving way for their wider application in the aerospace, automotive, and shipbuilding industries, where homogeneous microstructural qualities are of significant importance.

Analyzing the Influence of Welding Process Selection on Residual Stresses in Tube-to-Tubesheet Welded Joints

Tube-to-tubesheet joints are used in the fabrication of shell and tube type heat exchangers, steam generators, boilers, condensers, and end shields of pressure tube type nuclear reactors like CANDU (Canada Deuterium Uranium) and PHWR (Pressurized Heavy Water Reactor). The weld joints connecting the tubes to the tubesheets are of prime importance as they have a direct impact on equipment safety. In the fabrication of these critical class-1 nuclear components, full penetration weld joints are used. Typically, these full penetration weld joints are created through multi-pass Tungsten Inert Gas (TIG) welding. However, more recent techniques, such as single-pass Electron Beam Welding (EBW) and Laser Beam Welding (LBW), have also been employed for this purpose. The fabrication time of these pieces of equipment containing full penetration weld joints can be drastically reduced if single-pass welding techniques are used compared to multi-pass welding techniques. However, the residual stresses developed in these joints due to the localized heat input and the substantial constraints of the tubesheet are unknown. Different welding processes, such as TIG welding, EBW, or LBW, can lead to varying levels of residual stresses in these joints, subsequently impacting their longevity. Weld residual stress plays a significant role in the initiation of failure modes of these tube-to-tubesheet welded joints, such as stress corrosion cracking, fatigue, and corrosion fatigue.This paper analyzes the residual stresses developed at the tube-to-tubesheet interface resulting from different welding techniques, such as multi-pass TIG welding and single-pass EBW/LBW. A comprehensive three-dimensional coupled thermo-mechanical finite element analysis is employed for this purpose. The findings reveal a significant difference, with single-pass EBW exhibiting up to 32% lower residual stresses compared to multi-pass TIG welding. Additionally, the Heat Affected Zone (HAZ) in EBW is approximately 50% smaller than in TIG welding, and the equivalent distortion in EBW is reduced by 90% compared to multi-pass TIG welding. In summary, this investigation concludes that single-pass EBW offers distinct advantages for tube-to-tubesheet weld joints, including reduced residual stresses, a smaller HAZ, and lower distortions.

Effect of air velocity variation on hardness vickers of 6061 aluminum TIG welding joints

Aluminum 6061, a commonly used metal, demands critical attention in welding due to its mechanical properties influencing structural strength. The welding of aluminum 6061 is affected by various factors, including air velocity conditions during the welding process. This research objectives to analyze Vickers hardness values in TIG-welded Aluminum 6061. The research focuses on TIG welding of aluminum 6061, analyzing the impact of air velocity variations in the welding environment on hardness values. The experimental design considers air velocity variations at 3.6 km/h, 4 km/h, and 5 km/h during TIG welding of aluminum 6061. Specimens from each research variable undergo Vickers hardness testing to analyze the correlation between air velocity variations and Vickers hardness values. Research findings reveal specimen 1 with an average hardness of 96 HV, specimen 2 at 105 HV, and specimen 3 at 110 HV. These differences depict hardness variations among specimens, emphasizing the complexity of air velocity variations' effect on welded joints' hardness. Hardness testing results consistently show the lowest hardness values at point number 2, while the highest values for specimens 1 and 2 are at point number 6. However, specimen 3 exhibits the highest hardness at point number 8. The research concludes that air velocity variations in the welding environment significantly impact hardness values in the welding results. Vickers hardness testing indicates an increase in hardness values with increasing air velocity, highlighting a proportional relationship between air velocity variations and hardness values

Application of DFMA in lock band service modification of ATB-I3 building machine

The locking mechanism on the band service, known as the lock band service, is used to move materials to the tire-making machine. A building machine is a device that assembles components into partially finished or green tires. The components are tread, which acts as the tire tread, band/ply, which are fabric sheets coated in rubber, and bead wire. Subsequently, the materials are put together on the drum-mounted construction machine. The ATB-I3 machine has the largest downtime owing to a band service fault, with 840 minutes in January 2024, and is the problem with the highest downtime in section A2. The cause of the excessive downtime in the band service is an issue with the band service lock system, namely the pneumatic movement lock mechanism on the band service component. As a result, adjustments must be made by altering the lock band service's design. After that, a weld joint strength analysis is performed to make sure the modification can be safely put into practice. To obtain the optimal modification design, the DFMA method is employed. With the use of the DFMA approach, the updated design—which had a design efficiency value of 4.23% to 4.31% before—was improved. The welding connection in the updated design is safe to use since, according to the results of the welding connection calculation, the lock band service holder has a maximum welding load of 294,645.08 N whereas the actual welding load is 147,928 N. The reduction in service band downtime was tested with this improvement. Following the implementation of the update in March 2024, the amount of downtime resulting from damage to the band service dropped by 445 minutes, or 52.97%, to 395 minutes

Study on the Electron Beam Repair Welding of 5000 Aluminum Alloys

Electron beam welding (EBW) has been attracted due to its high energy density, high depth-to-width ratio, low thermal strain, compared with arc and laser welding. In addition, it ensures high quality weld joint in structural metals in a wide range of thickness from 0.025 mm to 300 mm. Therefore, EBW is widely used in industries such as automotive, aviation, nuclear power plant, etc. Although a lot of studies on EBW for several decades have been presented, EB based repair welding with supplement of filler metal has less reported. In this work, EB repair welding for 5083 aluminum alloys was investigated because the aluminum alloys are becoming more important as a lightweight material in mobility industries. Material characterization and mechanical properties of the repair-welded specimens were evaluated, compared with characteristics of base metal and bead welding without repair. The optimized experimental conditions showed tensile strength of 294 MPa, which is a similar to base metal. Our study indicates that EB repair welding can be considered for the candidate of repair welding of aluminum alloys.

Concept of Expert Software for Welding of Nodes from Inland Vessels

The structural integrity and safety of the vessels depends significantly on the quality of their welded joints, particularly at specific nodes where high-stress concentrations are common. This research leverages computer-aided design, artificial intelligence and materials science advancements to develop an innovative software tool that integrates expert knowledge, and best practices, for inland vessel welding. The proposed expert software system offers several key features, including the visualization of specific ship nodes, their parameters, as well as the residual stresses and strains that are specific to each node. By integrating these functionalities, the software aims to minimize human error, reduce inspection time, and ultimately improve the overall structural reliability of inland vessels.

On the Influence of Welding Parameters and Their Interdependence During Robotic Continuous Ultrasonic Welding of Carbon Fibre Reinforced Thermoplastics

Ultrasonic welding of fibre-reinforced thermoplastics is a joining technology with high potential for short welding times and low energy consumption. While the majority of the current studies on continuous ultrasonic welding have so far focused on woven reinforcements, unidirectional materials are preferred for highly loaded aerospace components due to their better mechanical performance. Therefore, this paper investigates the influence and interdependence of the welding speed, amplitude, and energy director thickness on the weld quality of adherends made of unidirectional composites. The quality of the welded joints is assessed by a single-lap shear strength and fracture surface analysis complemented by the microscopic analysis of cross-sections and comparison to a co-consolidated reference. The results showed that the welding process is highly affected by changing welding speeds for a given amplitude. Furthermore, while lower amplitudes lead to significant scatter in the welding quality, higher amplitudes result in increased heating rates and a fully molten energy director even for high welding speeds. Nevertheless, insufficient consolidation at high welding speeds results in porosity in the weld line. Finally, it was observed that thicker, and therefore more compliant, energy directors lead to more uniform melting of the energy director and less deviation in the weld quality for a wider range of welding speeds.

Research on the Cavitation Resistance Testing of Friction Stir Welded Joint of En Aw 1200 Aluminium Alloy

Aluminium alloys are being used more often as a result of industry demands for strong, lightweight materials. Because of its advantages over conventional fusion welding techniques, friction stir welding, or FSW, has become a promising technique for joining aluminium alloys. Nonetheless, there is still cause for concern regarding FSW joints' vulnerability to cavitation erosion, which is a major issue in applications exposed to harsh environments. The cavitation resistance of EN AW 1200 aluminium alloy joints made by the FSW process is the main objective of this study. By utilizing specialized equipment to conduct cavitation tests, the study uses a comprehensive methodology to assess the cavitation erosion behaviour of these joints. A number of variables are investigated in order to determine how they affect the cavitation resistance of the welded joints, including mechanical attributes, welding parameters, and microstructural features. The goal of the study is to shed light on how well FSW joints function and hold up in cavitation scenarios. This information will be useful in improving the dependability and suitability of EN AW 1200 aluminium alloy in sectors where the ability to withstand cavitation erosion is critical. The findings from this study are expected to contribute to the optimization of welding parameters and material selection, ultimately advancing the use of aluminium alloys in critical applications requiring resistance to cavitation-induced damage.

Investigation of the Inhibition Mechanism of Process Porosity in Laser-MIG Hybrid-Welded Joints for an Aluminum Alloy

In this paper, 4 mm thick 7075 aluminum alloy was utilized for conducting laser-MIG hybrid welding tests to investigate the correlation between the dynamic behavior of keyholes and process-induced porosity. Additionally, the generation and inhibition mechanisms of process porosity were elucidated. Utilizing a high-speed camera test system of our own design, the formation position and movement characteristics of keyholes in the molten pool under different welding parameters were captured using a “sandwich” method. The dynamic behavior of keyholes during the hybrid welding process was analyzed, and the porosity of each welded joint was quantified, revealing an intrinsic relationship between keyhole dynamics and aluminum alloy laser-MIG hybrid welding porosity. The findings indicate that variations in the defocusing amount can influence both the morphology and stability of keyholes in the molten pool, consequently impacting welding porosity. The dynamic behavior of keyholes under different defocusing amounts can be categorized into five types: no keyhole formation, collapse of the keyhole root, complete instability of the keyhole, instability of the keyhole root, and stability of the keyhole. At a defocus of +12 mm, stable keyholes were observed, and no defects in the welded joints were identified.

Mechanical performance of dissimilar Al6082 aluminum and AZ91 magnesium alloy joints produced by friction stir welding

Abstract The current research work aims to produce a defect free joint of Al6082 aluminum and AZ91 magnesium alloy sheets by friction stir welding (FSW) at various tool rotational and travel speeds with an objective to obtain the best combination of welding parameters to produce quality joint. The weld joint that was produced at the combination of 1400 rpm tool rotational speed and 30 mm min−1 feed exhibited defect free stir zone. Microstructural studies carried out in the weld joint demonstrated mechanical mixing of base materials from both the alloys in the stir zone. The mixing of Al6082 and AZ91 alloys was clearly appeared in the weld zone. It can be observed that the x-ray diffraction studies clearly demonstrated the development of intermetallics in the weld region. Higher hardness was observed for the joints that can be ascertained to the presence of more mixed regions in the stir zone that contains hard and brittle intermetallics. From the tensile test data, lower strength (175.71 ± 4.24 MPa) was observed for the weld joint compared with Al6082 (242. 6 ± 11.4 MPa) and AZ91 (205.27 ± 6.39 MPa) base materials. Furthermore, the ductility of the weld joint was measured as marginally higher than the AZ91 Mg alloy and lower than the Al6082 alloy. It can be concluded that the defect free weld joints of Al6082-AZ91 alloys can be successfully produced by FSW for structural applications targeted for dry environment.

Mechanical Properties and Microstructural Characteristics of Steel Pipes after Long-Time Hydrogen Exposure

There are three possibilities to transport hydrogen by high pressure pipeline (i) blending hydrogen into the existing natural gas pipeline system, (ii) after checking the integrity, using the natural gas transporting pipeline system to transport hydrogen, (iii) building a new pipeline system to transport pure hydrogen. In all three cases should be known the behaviour of the pipe material and its welded joints influenced under high pressure hydrogen. For this aim pipeline sections made of P355NH base material were investigated without and with hydrogen exposure, where the exposure time was 41 days. Gas metal arc welding and hybrid tungsten arc welding / gas metal arc welding were applied for preparation of the girth weld joints. Tensile, three point bending and hardness tests, furthermore microstructural investigations were performed both on base materials and girth welds of the pipeline sections. The testing results were analysed and compared with each other (base material vs. welded joints, without exposure vs. with exposure) and with limit values can be found in the literature. Conclusions were drawn on the behaviour of the investigated pipe material and its welded joints.

Creep Behavior and Fracture Mechanisms of the Dissimilar Inertia Friction Welded Joints of Deformed and Powder Metallurgy Ni‐Based Superalloys

ABSTRACTIn this research, the microstructure and precipitate characteristics of the dissimilar inertia friction welded (IFW) joints of deformed and powder metallurgy (PM) nickel‐based superalloys were studied using optical, scanning electron, and transmission electron microscopy. In addition, several creep tests were conducted. The high‐temperature mechanical properties of the IFW joints were systematically analyzed. Under the creep testing condition of 680°C, the specimens exhibited creep fracture at the thermomechanically affected zone (TMAZ) of the PM superalloys. Further, the failure lifetime is enhanced with a reduction in the applied creep loading. Owing to the IFW process, various γ′ precipitates and carbide distributions were observed in the various zones of a dissimilar IFW joint. Undissolved powder particle boundary (PPB) defects in the TMAZ of the PM superalloy initiated creep cracks under creep loading. Based on the experimental results and theoretical analysis, the creep fracture mechanisms of the dissimilar IFW joints were revealed. Thus, the findings of this study provide guidance for controlling the microstructures and properties of dissimilar deformed/PM nickel‐based superalloy IFW joints.

A Review of Welding Process for UNS S32750 Super Duplex Stainless Steel

Super duplex stainless steel UNS S32750 is widely used in marine industries, pulp and paper industries, and the offshore oil and gas industry. Welding manufacturing is one of the main manufacturing processes to make material into products in the above fields. It is of great importance to obtain high-quality welded UNS S32750 joints. The austenite content and ferrite content in UNS S32750 play an important role in determining UNS S32750 properties such as mechanical properties and corrosion resistance. However, the phase proportion between the ferrite phase and austenite phase in the welded joint will be changed during welding. Lots of research has been done on how to weld UNS S32750 and how to obtain welded joints with good quality. In this work, the recent studies on welding UNS S32750 are categorized based on the welding process. The welding process for UNS S32750 will be classified as gas tungsten arc welding, submerged arc welding, plasma arc welding, laser beam welding, electron beam welding, friction stir welding, and laser-MIG hybrid welding, and each will be reviewed in turn. The microstructure and properties of the joints welded using different welding processes will also be discussed. The critical challenge of balancing the two phases of austenite and ferrite in UNS S32750 welded joints will be discussed. This review about the welding process for UNS S32750 will provide people in the welding field with some advice on welding UNS S32750 super duplex stainless steel.

Experimental and Numerical Characterization of Local Properties in Laser-Welded Joints in Thin Plates of High-Strength–Low-Alloy Steel and Their Dependence on the Welding Parameters

Laser welding on thin plates of high-strength steel is increasing in various industrial applications. The mechanical behavior of welded joints depends on their local properties, which in turn depend on the welding parameters applied to join the base material. This work characterizes the local properties of butt-welded joints of thin plates of high-strength–low-alloy (HSLA) steel. This study focuses on the effect of welding parameters on the microstructure, tensile response, microhardness, and weld bead profile. For this purpose, a factorial experimental design was formed, covering a heat input range from 53 to 75 J/mm. This study identified the main effects and interactions of welding speed and laser power on the weld bead profile and on its width. The microstructure, weld bead width, hardness, and tensile mechanical properties were significantly influenced by heat input. Furthermore, numerical simulations on real weld bead profiles revealed high values of the stress concentration factor and suggested a correlation with heat input.

A Case Study on the Possibility of Extending the Service Life of the Demining Machine Belt

The operational practice of the design of the Bozena 5 demining machine has shown that its belts are the critical component that fundamentally affects the functionality of the entire machine. This article is a practical continuation and extension of the previous research results from the point of view of materials (research of the uniaxial fatigue life in bending and torsion), calculation (creation of the necessary mathematical, analytical and numerical models for the research) and construction (i.e., patented design of the belt tensioning of this machine). All these actions are aimed at a single objective—to achieve a condition that guarantees a sufficient service life without malfunctions, since repairing these machines in the field is often impossible. Therefore, this study examined the fatigue life of welded joints (uniaxial bending and torsion) of S960 QL and S500MC steels welded by MAG technology. Subsequently, the data were compared with previous results (electron and laser welds) and the influence of each type of weld on the fatigue life relative to the base material was discussed. It was found that conventional MAG technology had a more significant negative impact on the fatigue life of the base material than non-conventional technologies. This trend was particularly true for the bending stress. At the same time, the bending stress was identified by the FEM analysis as the dominant load on the belt. The maximum stress in the belt link under the considered boundary conditions was approximately 240 MPa (in bending). This stress corresponded to the continuous fatigue life (more than 107 cycles) for both base materials tested (S960QL, S500MC). In the whole studied spectrum of controlled deformation amplitudes (Manson–Coffin), the life of MAG welds was lower in comparison with the base material and with welds made by unconventional technologies. All the activities carried out so far (research on microstructure, hardness, strength, residual stresses, tribological properties and fatigue life) have shown that the original belt design (S500MC) using MAG technology has significant deficiencies in the state of optimal life. It is expected that the proposed material change (use of S960QL instead of S500MC) and work with advanced technologies will bring this state significantly closer.

The influence of cooling time on the alloy distribution in weld metals

This research explores the impact of cooling time on the distribution of alloying elements within weld metals of high-strength steel, a critical factor in optimizing welding processes for advanced structural applications. Using gas metal arc welding (GMAW) and two different filler materials, this study systematically varies cooling times to analyze the resulting chemical compositions. Energy Dispersive X-ray (EDX) analysis was employed to examine the alloy content in the weld metal, base material, and heat-affected zone (HAZ). The results demonstrate that cooling time significantly influences the concentration of alloying elements, such as chromium, nickel, and manganese, within the weld metal, revealing complex diffusion behaviours that are dependent on the thermal cycles introduced during welding. Notably, an in-depth analysis of the HAZ shows a distinct diffusion pattern for silicon, indicating intricate microstructural changes. These findings highlight the importance of controlling cooling time to optimize the microstructural and chemical properties of welded joints in high-strength steels, with implications for improving weld performance and reliability.

Influence of tempering on structure and properties of welded joints of high-strength structural steel achieved by submerged arc welding

The paper describes mechanical properties and microstructure of weld metal of welded joints of high-strength structural steel AB3K made by automatic submerged arc welding with K-shaped edge cutting. The comparative analysis of the process using Sv-07KhN3MD wire and 48A3 flux subjected to heat treatment under four different modes is carried out.

Comparison of destructive and non-destructive fracture toughness measurements for Q235 steel butt-welded joint

As a critical component of a welded structure, the integrity of the welded joint significantly affects the safety and reliability of the structure in service. Therefore, it is essential to investigate the integrity of welded joints. However, given the harshness of standard measurements renders them unsuitable for application to small volume zones, welded structures or in-service structures. In this study, the fracture properties of a Q235 steel butt-welded joint was evaluated by boundary effect modelling (BEM) method and the ball indentation (BI) method. The results demonstrate that the fracture toughness distribution obtained by the two methods are consistent, with the highest fracture toughness in the weld metal, followed by the heat-affected zone and the base metal, and the lowest fracture toughness in the fusion zone, which is in agreement with the results of the metallographic testing. Furthermore, the relative errors of the zones obtained by the ball indentation method and the boundary effect modelling method ranging from 10.16 to 19.05%, which indicates safety margin ought to be considered for employing the BI method to determine fracture properties of in-service structures.