Weight-bearing Flexion Research Articles

Tibiofemoral articulation and axial tibial rotation of the knee after a cruciate retaining total knee arthroplasty

PurposeNumerous research has reported that total knee arthroplasty (TKA) cannot reproduce axial tibial rotations of normal knees. The objective of this study was to measure the tibiofemoral articular contact motions and axial tibial rotations of TKA knees to investigate the mechanism causing the knee kinematics change of after TKAs.MethodsEleven patients with unilateral cruciate retaining (CR) TKA were tested for measurements of knee motion during a weight-bearing flexion from 0° to 105° using an imaging technique. The tibiofemoral contact kinematics were determined using the contact points on medial and lateral surfaces of the tibia and femoral condyles. Axial tibial rotations were calculated using the differences between the medial and lateral articulation distances on the femoral condyles and tibial surfaces at each flexion interval of 15°.ResultsOn femoral condyles, articular contact distances are consistently longer on the medial than on the lateral sides (p < 0.05) up to 60° of flexion, corresponding to internal tibial rotations (e.g., 1.3° ± 1.0° at 15–30° interval). On tibial surfaces, the articular contact point on the medial side moved more posteriorly than on the lateral side at low flexion angles, corresponding to external tibial rotations (e.g., −1.4° ± 1.8° at 15–30° interval); and more anteriorly than on the lateral sides at mid-range flexion, corresponding to internal tibial rotations (e.g., 0.8° ± 1.7° at 45–60° interval). At higher flexion, articular motions on both femoral condyles and tibial surfaces caused minimal changes in tibial rotations.ConclusionsThese results indicate that the axial tibial rotations of these TKA knees were mainly attributed to asymmetric articulations on the medial and lateral femoral condyles and tibial surfaces. The data can help understand the mechanisms causing axial tibial rotations of TKA knees and help improve implant designs for restoration of normal knee kinematics.

In Vivo Weight-Bearing Kinematics for Constrained Versus Traditional Bicruciate Stabilized Total Knee Arthroplasty Cohorts Compared to the Normal Knee

BackgroundConstrained inserts in total knee arthroplasty (TKA) may offer additional stability, but can this insert type allow unrestricted movements or will the extra conformity cause kinematic conflict with the cam-post mechanism in deeper flexion? The objective of this study was to evaluate the weight-bearing kinematics of both traditional and constrained bicruciate stabilized (BCS) TKA inserts to determine if the rollback induced by the cam-post mechanism will work in unison with the constrained polyethylene insert. MethodsThis study used previously published 3-dimensional model fitting techniques to compare weight-bearing flexion and femoro-tibial condylar motion patterns for 20 patients who had a traditional insert, 20 patients who had a constrained insert, and 10 previously published nonimplanted knees, all performing a deep knee bend activity while under fluoroscopic surveillance. ResultsThe results from this study indicate that subjects having a bicruciate stabilized TKA experienced similar postoperative kinematics for both constrained and unconstrained insert options, comparable to normal knees. ConclusionsSubjects in this study having either a constrained or traditional insert experienced progressive rollback of both condyles, with the lateral condyle rolling more posterior than the medial condyle, leading to axial rotation. Although less in magnitude, these results were comparable to the normal knee in pattern, indicating that kinematic conflict did not occur for subjects having a constrained insert.

Investigation of Characteristic Motion Patterns of the Knee Joint During a Weightbearing Flexion.

This study aimed to develop and validate a novel flexion axis concept by calculating the points on femoral condyles that could maintain constant heights during knee flexion. Twenty-two knees of 22 healthy subjects were investigated when performing a weightbearing single leg lunge. The knee positions were captured using a validated dual fluoroscopic image system. The points on sagittal planes of the femoral condyles that had minimal changes in heights from the tibial plane along the flexion path were calculated. It was found that the points do formulate a medial-lateral flexion axis that was defined as the iso-height axis (IHA). The six degrees of freedom (6DOF) kinematics data calculated using the IHA were compared with those calculated using the conventional transepicondylar axis and geometrical center axis. The IHA measured minimal changes in proximal-distal translations and varus-valgus rotations along the flexion path, indicating that the IHA may have interesting clinical implications. Therefore, identifying the IHA could provide an alternative physiological reference for improvement of contemporary knee surgeries, such as ligament reconstruction and knee replacement surgeries that are aimed to reproduce normal knee kinematics and medial/lateral soft tissue tensions during knee flexion.

Do High-Flexion Total Knee Arthroplasty Have More Adverse Events™

Introduction: High-flexion knee prosthesis was proposed to result in better outcomes after knee arthroplasty. However, latest meta-analysis revealed that this implant indeed only produced better range of motion (ROM) and no benefits in other functional outcomes, including weight-bearing flexion. Moreover, recent studies suggested that more complications occurred in high-flexion total knee arthroplasty (TKA) instead. Objectives: This study focuses on the adverse events of high-flexion TKA compared to standard TKA in mid to long term of follow-up. Methods: Systematic search was done in online databases, i.e. Pubmed, ScienceDirect, ClinicalKey. We only included studies with a minimum follow-up duration of 5 years, expecting that this mid to long term follow-up could provide a better picture of the outcomes. Results: Seven studies were included in the final quantitative analyses, involving a total of 2,693 knees in high-flexion TKA and 3,892 knees in standard TKA. High-flexion TKA significantly had higher revision surgery compared to standard TKA (p = 0.03), 41(1.52%) and 53 (1,36%) knees, respectively. Loosening was not statistically different between those groups. Generally, radiolucent line was also more frequently observed in high-flex TKA (p = 0.01), 7.43% V 3.83% at femoral side and 5.69% V 4.41% at tibial side. Although infection and instability were higher in high-flexion knee, only a few studies found the occurrence of these parameters. Four studies evaluated the incidence of osteolysis and none was found in both groups. Conclusion: Considering that high-flexion TKA may only yield on better ROM but carry a bigger risk of adverse events, one has to cautiously weighing up the benefits and risks when planning of delivering a high-flexion TKA.

Physiological Axial Tibial Rotation of the Knee During a Weightbearing Flexion.

Axial tibial rotation is a characteristic motion of the knee, but how it occurs with knee flexion is controversial. We investigated the mechanisms of tibial rotations by analyzing in vivo tibiofemoral articulations. Twenty knees of 20 living human subjects were investigated during a weightbearing flexion from full extension to maximal flexion using a dual fluoroscopic imaging system. Tibiofemoral articular contact motions on medial and lateral femoral condyles and tibial surfaces were measured at flexion intervals of 15 deg from 0 deg to 120 deg. Axial tibial rotations due to the femoral and tibial articular motions were compared. Articular contact distances were longer on femoral condyles than on tibial surfaces at all flexion intervals (p < 0.05). The articular distance on medial femoral condyle is longer than on lateral side during flexion up to 60 deg. The internal tibial rotation was 6.8 ± 4.5 deg (Mean ± SD) at the flexion interval of 0-15 deg, where 6.1 ± 2.6 deg was due to articulations on femoral condyles and 0.7 ± 5.1 deg due to articulations on tibial surfaces (p < 0.05). The axial tibial rotations due to articulations on femoral condyles are significantly larger than those on tibial surfaces until 60 deg of flexion (p < 0.05). Minimal additional axial tibial rotations were observed beyond 60 deg of flexion. The axial tibial rotations were mainly attributed to uneven articulations on medial and lateral femoral condyles. These data can provide new insights into the understanding of mechanisms of axial tibial rotations and serve as baseline knowledge for improvement of knee surgeries.

A novel use of cone beam CT: flexion and extension weight-bearing imaging to assess spinal stability

To assess spinal stability in different physiological positions whilst weight-bearing. A cone beam CT scanner (CBCT) was used to identify any abnormal motion in the spine in different physiological positions whilst weight-bearing. The lumbar spine was assessed in 6 different patients with a comfortable neutral standing position and standing flexion and extension images in selected patients. Seated, weight-bearing flexion and extension images of the cervical spine were obtained in a further patient. Clinical indications included stability assessment post-trauma, post-surgical fusion and back pain. The projection images were reconstructed using bone and soft tissue algorithms to give isotropic CT images which could be viewed as per conventional multi-detector CT images. The flexion and extension CBCT data were fused to give a representation of any spinal movement between the extremes of motion. The flexion and extension weight-bearing images gave anatomical detail of the spine. Detail of the surgical constructs was possible. Dynamic structural information about spinal alignment, facet joints, exit foramina and paraspinal musculature was possible. The effective dose from the neutral position was equal to that of supine, multi-detector CT. CBCT can be used to image the lumbar and cervical spine in physiological weight-bearing positions and at different extremes of spinal motion. This novel application of an existing technology can be used to aid surgical decision making to assess spinal stability and to investigate occult back and leg pain. Its use should be limited to specific clinical indications, given the relatively high radiation dose.

Articulation of the femoral condyle during knee flexion

Femoral condyle motion of the knee is generally reported using a morphological trans-epicondyle axis (TEA) or geometric center axis (GCA) in the investigation of the knee kinematics. Axial rotation of the femur is recognized as a characteristic motion of the knee during flexion, but is controversial in the literature. This study investigated the biomechanical factors that could be associated to the axial rotations of the femur using both physiological and morphological measurement methods. Twenty healthy knees were investigated during a weightbearing flexion from 0° to 120° at a 15° increment using an imaging technique. A 3D model was constructed for each knee using MR images. Tibiofemoral cartilage contact points were determined at each flexion position to represent physiological knee motion. The contact distance on each condyle was measured between consecutive contact points. The TEA and GCA were used to measure morphological anteroposterior translations of the femoral condyles. The differences between the medial and lateral condyle motions were used to calculate the physiological and morphological axial rotations of the femur. Both the physiological and morphological methods measured external rotations of the femur at low flexion range (0°-45°) and minimal rotations at higher flexion angles. However, the morphological method measured larger posterior translations of the lateral femoral condyle than the medial condyle (p < 0.05), implying a medial pivoting rotation; in contrast, the physiological method measured larger contact distances on the medial condyle than on the lateral condyle (p < 0.05), implying a lateral pivoting rotation. These data could provide useful references for future investigation of kinematics of the knee before and after surgical repair, such as using total knee arthroplasty.

The MRI-based 3D morphologic changes of knee meniscus under knee weight-bearing and early flexion conditions

There are few studies investigate morphologic changes of knee meniscus in vivo mechanical loading and three-dimensions (3D) deformation and displacement of the whole meniscus between in vivo mechanical loading and unloading conditions are still unclear. To investigate the displacements and 3D morphological changes of the menisci under knee weight-bearing and early flexion conditions in healthy adults using a Magnetic Resonance Imaging (MRI)-compatible loading device (a 3.0 T MR imaging system) combined with a newly developed 3D comparison technique. Fifteen healthy volunteers were recruited in this cross-sectional observational study. Each subject underwent MRIs of their dominant right knee in eight different scanning conditions using a 3.0-T MRI scanner with a custom-made MRI-compatible loading device. The knee meniscus images were 3D reconstructed, and dimensional comparisons were made for each meniscal model with baseline (0°-unloaded model). The morphologic changes of the meniscal-anterior horn (AH), body (BD), and posterior horn (PH) regions were expressed as mean positive and negative deviations. The displacements were further investigated, and the meniscal extrusions of different subregions were measured. The morphologic changing patterns of human meniscus under loading and flexions were presented using 3D chromatic maps. The bilateral menisci were generally shifting laterally and posteriorly in most flexion angles and were changing medially and anteriorly under fully extended knee loading conditions. The mean deviations were more significant with loading at 0° of knee flexion, while the PH region in the lateral side changed further posteriorly with loading in 30° flexion. Most of the differences were not significant in other flexion angles between loading conditions. The extrusion of meniscus’s medial body was greater in full extension compared to any other flexing angles. Mechanical loading can significantly deform the menisci in knee extension; however, this effect is limited during knee flexion. Current study can be used as a reference for the evaluations of the integrity in meniscal functions.

Gender differences in knee kinematics during weight-bearing knee flexion for patients with arthrofibrosis after anterior cruciate ligament reconstruction

BackgroundKnowledge of tibiofemoral and patellofemoral joint kinematics is important for understanding gender-related dimorphism in developing knee arthrofibrosis and advancement of related treatments. The objective of our study was to investigate gender differences existing in tibiofemoral kinematics and patellar tracking in patients with arthrofibrosis after anterior cruciate ligament (ACL) reconstruction during weight-bearing knee flexion.MethodsThe tibiofemoral and patellofemoral joint kinematics were measured in 30 patients (15 male and 15 female) with arthrofibrosis after ACL reconstruction during a lunge task, using computed tomography and dual fluoroscopic imaging system. These data were analyzed for gender differences.ResultsThe range of tibial rotation, patellar inferior shift, tilt, and flexion were significantly decreased in the affected knee compared to the contralateral knee from 15° to 75° of knee flexion (P ≤ 0.04). Statistically significant difference was detected for medial tibial translation between male and female patients at 60° (P = 0.04) and 75° of knee flexion (P = 0.02). The tibial rotation was significantly decreased at 60° (P = 0.03) and 75° of knee flexion (P < 0.01) in females. The inferior patellar shift in females was significantly lower than that in males at 15° (P = 0.04) and 30° of knee flexion (P = 0.01). The patellar tilt was significantly lower at 60° (P = 0.02) and 75° of knee flexion (P < 0.01) in females compared to males.ConclusionsThe results indicated a significant effect of gender on knee kinematics in patients with arthrofibrosis after ACL reconstruction during weight-bearing knee flexion. These gender differences in tibiofemoral kinematics and patellar tracking may warrant further investigations to determine implications for making gender-specific surgical treatments and rehabilitation programs.

Investigation of femoral condyle height changes during flexion of the knee: implication to gap balance in TKA surgery.

Gap balance of the knee at 0° and 90° of flexion has been pursued in total knee arthroplasty (TKA) with the trans-epicondyle axis (TEA) as a reference. This study investigated the height changes of the tibiofemoral articulation and compared the data with the femoral condyle height changes measured using different flexion axes. Twenty healthy knees were investigated during an invivo weightbearing flexion using a techniquecombining MRI anda dual fluoroscopic imaging system (DFIS). The tibiofemoral contact points and the femoral condyle heights [measured using: TEA, geometric center axis (GCA), and iso-height axis (IHA)] were determined at each flexion angle. The height changes of the articular contact points and the femoral condyles were compared along the flexion path. The changes of the medial and lateral contact point heights were within 2.5mm along the flexion path. The changes of the medial and lateral condyle heights were within 8.9mm for TEA, within 4.2mm for GCA and within 3.0mm for IHA. The height changes measured by the contact points and IHA are similar (p > 0.05), and both are significantly smaller than those measured using the TEA and GCA (p < 0.05). The TEA and GCA measured varying femoral condyle heights, but the IHA resulted in minimal condyle height changes and could better represent the articulation characteristics of the knee. The data suggested that the IHA could be used as an alternative reference to guide surgical preparation of gap balance along the knee flexion path during TKA surgeries.

Weight-bearing knee flexion angle better correlates with patient-reported outcome measures than non-weight-bearing condition in total knee arthroplasty: a three-dimensional analysis study

BackgroundThis study aims to elucidate and compare the relationship between the knee flexion angle and patient-reported outcome measures (PROM) in both non-weight-bearing (NWB) and weight-bearing (WB) conditions.MethodsThis retrospective cohort study included 61 knees (47 patients) who underwent total knee arthroplasty. The knee flexion angle was measured by three conditions: NWB in manual goniometer, NWB in fluoroscopic three-dimensional (3D) analysis and WB in the fluoroscopic 3D analysis. The PROM was evaluated by postoperative 2011 Knee Society Score (2011 KSS) and Knee injury and Osteoarthritis Outcome Score (KOOS). Correlations between the knee flexion angle and PROM was analyzed using Spearman’s correlation coefficient. Additionally, whether the angular difference between NWB and WB correlated with the PROM or not was evaluated.ResultsThe NWB knee flexion angle in a goniometer, NWB in 3D analysis, and WB in 3D analysis were 124.6° ± 8.4°, 118.0° ± 10.5°, and 109.5° ± 13.3°, respectively. The angular difference was 8.5° ± 12.8°. No PROM correlation existed in NWB using a goniometer. Moreover, significant positive correlations in 2011 KSS symptoms (r = 0.35) and 2011 KSS functional activities (r = 0.27) were noted in NWB using 3D analysis. Significant positive correlations existed in 2011 KSS symptoms (r = 0.32), 2011 KSS functional activities (r = 0.57), KOOS pain (r = 0.37), KOOS activity of daily living (ADL; r = 0.45), KOOS sports (r = 0.42), and KOOS quality of life (r = 0.36) in WB using 3D analysis. Significant negative correlations were noted in 2011 KSS functional activities (r = − 0.45), KOOS ADL (r = − 0.30), and KOOS sports (r = − 0.38) in angular difference.ConclusionsThe WB knee flexion angle better correlated with PROM compared with NWB by evaluation of 3D analysis. The larger the angular difference existed between NWB and WB, the lower the PROM score.

Meniscal Deficiency Period and High Body Mass Index Are Preoperative Risk Factors for Joint Space Narrowing After Meniscal Allograft Transplantation

Background: Several studies have reported further reduction in joint space width (JSW) after meniscal allograft transplantation; some contributing postoperative factors are known, although preoperative factors remain unclear. This study is the first to analyze the preoperative risk factors for reduced JSW in patients after lateral meniscal allograft transplantation (LMAT). Hypothesis: Poor cartilage status and high preoperative body mass index (BMI) influence the postoperative progression of joint space narrowing. Study Design: Case-control study; Level of evidence, 3. Methods: We retrospectively studied 79 patients after LMAT who were observed for at least 5 years. JSWs on weightbearing flexion posteroanterior radiographs were measured preoperatively and at the 5-year mark. Differences in JSW were divided into more progression and less progression groups. The modified Outerbridge cartilage grades based on magnetic resonance imaging assessments were compared at subtotal/total meniscectomy and at LMAT to determine the difference between time points. Preoperative between-group differences in sex, age, surgical side, follow-up period, weight, height, BMI, and meniscal deficiency period were analyzed. Clinical outcomes were evaluated using the Lysholm score. Data were examined using univariate and multivariate logistic regressions. Results: Radiographically, the overall change in JSW from preoperative to follow-up was 0.58 mm (range, –0.23 to 1.83 mm). Reductions in JSW in the more progression and less progression groups were 0.94 ± 0.32 and 0.22 ± 0.21 mm (mean ± SD), respectively. There was no difference in cartilage status between the groups at meniscectomy or LMAT; however, changes between time points were significant on the lateral femoral condyle and lateral tibial plateau. Clinically, there were significant differences in weight, BMI, and meniscal deficiency period between the 2 groups. Postoperative Lysholm scores increased as compared with the preoperative scores, but there was no difference among the postoperative time points. In the univariate logistic regression risk analysis, weight, BMI, meniscal deficiency period, and the difference in cartilage status between time points for the lateral femoral condyle and lateral tibial plateau were identified as significant. In the subsequent multivariate logistic regression, BMI (odds ratio, 1.45; P = .016) and meniscal deficiency period (odds ratio, 1.21; P = .037) were the statistically significant factors. Conclusion: BMI and meniscal deficiency period were preoperative risk factors for JSW narrowing after LMAT. This suggests that the meniscal deficiency period from meniscectomy to LMAT may be shortened and that proper weight management can lead to successful LMAT.

Asymmetrical tibial polyethylene geometry-cruciate retaining total knee arthroplasty does not fully restore in-vivo articular contact kinematics during strenuous activities.

A new CR TKA design with concave medial and convex lateral tibial polyethylene bearing components was introduced recently to improve functional outcomes. This study aimed to investigate in-vivo articular contact kinematics in unilateral asymmetrical tibial polyethylene geometry CR TKA patients during strenuous knee flexion activities. Fifteen unilateral CR TKA patients (68.4 ± 5.8years; 6 male/9 female) were evaluated for both knees during sit-to-stand, single-leg deep lunges and step-ups using validated combined computer tomography and dual fluoroscopic imaging system. Medial and lateral condylar contact positions were quantified during weight-bearing flexion activities. The Wilcoxon signed-rank test was performed to determine if there is a significant difference in articular contact kinematics during strenuous flexion activities between CR TKA and the non-operated knees. Contact excursions of the lateral condyle in CR TKAs were significantly more anteriorly located than the contralateral non-operated knee during sit-to-stand (3.7 ± 4.8mm vs - 7.8 ± 4.3mm) and step-ups (- 1.5 ± 3.2mm vs - 6.3 ± 5.8mm). Contact excursions of the lateral condyle in CR TKAs were significantly less laterally located than the contralateral non-operated knee during sit-to-stand (21.4 ± 2.8mm vs 24.5 ± 4.7mm) and single-leg deep lunges (22.6 ± 4.4mm vs 26.2 ± 5.7mm, p < 0.05). Lateral condyle posterior rollback was not fully restored in CR TKA patients during sit-to-stand (9.8 ± 6.7mm vs 12.9 ± 8.3mm) and step-ups (8.1 ± 4.8mm vs 12.2 ± 6.4mm). Lateral pivoting patterns were observed in 80%, 73% and 69% of patients during sit-to-stand, step-ups and single-leg deep lunges respectively. Although lateral femoral rollback and lateral pivoting patterns were observed during strenuous functional daily activities, asymmetric contact kinematics still persisted in unilateral CR TKA patients. This suggests the specific investigated contemporary asymmetrical tibial polyethylene geometry CR TKA design evaluated in this study does not fully replicate healthy knee contact kinematics during strenuous functional daily activities. III.

In Vivo Knee Kinematics: How Important Are the Roles of Femoral Geometry and the Cruciate Ligaments?

BackgroundWhile posterior cruciate-retaining (PCR) implants are a more common total knee arthroplasty (TKA) design, newer bicruciate-retaining (BCR) TKAs are now being considered as an option for many patients, especially those that are younger. While PCR TKAs remove the ACL, the BCR TKA designs keep both cruciate ligaments intact, as it is believed that the resection of the ACL greatly affects the overall kinematic patterns of TKA designs. The objectives of this study are to assess the in vivo kinematics for subjects implanted with either a PCR or BCR TKA and to compare the in vivo kinematic patterns to the normal knee during flexion. These objectives were achieved with an emphasis on understanding the roles of the cruciate ligaments, as well as the role of changes in femoral geometry of nonimplanted anatomical femurs vs implanted subjects having a metal femoral component. MethodsTibiofemoral kinematics of 50 subjects having a PCR (40 subjects) or BCR (10 subjects) TKA were analyzed using fluoroscopy while performing a deep knee bend activity. The kinematics were compared to previously published normal knee data (10 subjects). Kinematics were determined during specific intervals of flexion where the ACL or PCL was most dominant. ResultsIn early flexion, subjects having a BCR TKA experienced more normal-like kinematic patterns, possibly attributed to the ACL. In mid-flexion, both TKA groups exhibited variable kinematic patterns, which could be due to the transitional cruciate ligament function period. In deeper flexion, both TKA functioned more similar to the normal knee, leading to the assumption that the PCL was properly balanced and functioning in the TKA groups. Interestingly, during late flexion (after 90°), the kinematic patterns for all three groups appeared to be statistically similar. ConclusionSubjects having a PCR TKA experienced greater weight-bearing flexion than the BCR TKA group. Subjects having a BCR TKA exhibited a more normal-like kinematic pattern in early and late flexion. The normal knee subjects achieved greater lateral condyle rollback and axial rotation compared to the TKA groups.

In Vivo Knee Kinematics for a Cruciate Sacrificing Total Knee Arthroplasty Having Both a Symmetrical Femoral and Tibial Component

BackgroundEarly total knee arthroplasty (TKA) designs were symmetrical, but lead to complications due to over-constraint leading to loosening and poor flexion. Next-generation TKAs have been designed to include asymmetry, pertaining to the trochlear groove, femoral condylar shapes, and/or the tibial component. More recently, an advanced posterior cruciate sacrificing (PCS) TKA was designed to include both a symmetrical femoral component with a patented V-shaped trochlear groove and a symmetrical tibial component with an ultracongruent insert, in an attempt to reduce inventory costs. Because previous PCS TKA designs produced variable results, the objective of this study is to determine and evaluate the in vivo kinematics for subjects implanted with this symmetrical TKA. MethodsTwenty-one subjects, implanted with symmetrical PCS fixed-bearing TKA, were asked to perform a weight-bearing deep knee bend (DKB) while under fluoroscopic surveillance. A 3-dimensional to 2-dimensional registration technique was used to determine each subject’s anteroposterior translation of lateral and medial femoral condyles as well as tibiofemoral axial rotation and their weight-bearing knee flexion. ResultsDuring the DKB, the average active maximum weight-bearing flexion was 111.7° ± 13.3°. On average, from full extension to maximum knee flexion, subjects experienced −2.5 ± 2.0 mm of posterior femoral rollback of the lateral condyle and 2.5 ± 2.2 mm of medial condyle motion in the anterior direction. This medial condyle motion was consistent for the majority of the subjects, with the lateral condyle exhibiting rollback from 0° to 60° of flexion and then experienced an average anterior motion of 0.3 mm from 60° to 90° of knee flexion. On average, the subjects in this study experienced 6.6°± 3.3° of axial rotation, with most of the rotation occurring in early flexion, averaging 4.9°. ConclusionAlthough subjects in this study were implanted with a symmetrical PCS TKA, they did experience femoral rollback of the lateral condyle and a normal-like pattern of axial rotation, although less in magnitude than the normal knee. The normal axial rotation pattern occurred because the lateral condyle rolled in the posterior direction, while the medial condyle moved in the anterior direction. Interestingly, the magnitude of posterior femoral rollback and axial rotation for subjects in this study was similar in magnitude reported in previous studies pertaining to asymmetrical TKA designs. It is proposed that more patients be analyzed having this TKA implanted by other surgeons.

Kinematic Performance of Gradually Variable Radius Posterior-Stabilized Primary TKA During Various Activities: An In Vivo Study Using Fluoroscopy

BackgroundPosterior-stabilized total knee arthroplasty (TKA) with gradually variable radii (G-curve) femoral condylar geometry is now available. It is believed that a G-curve design would lead to more mid-flexion stability leading to reduced incidence of paradoxical anterior slide. The objective of this study was to assess the in vivo kinematics for subjects implanted with this type of TKA under various conditions of daily living. MethodsTibiofemoral kinematics of 35 patients having posterior-stabilized TKA with G-curve design were analyzed using fluoroscopy while performing three activities: weight-bearing deep knee bend, gait, and walking down a ramp. The subjects were assessed for range of motion, condylar translation, axial rotation, cam-spine engagement, and condylar lift-off. ResultsThe average weight-bearing flexion during deep knee bend was 111.4°. On average, the subjects exhibited 5.4 mm of posterior rollback of the lateral condyle and 2.0 mm of the medial condyle from full extension to maximum knee flexion. The femur consistently rotated externally with flexion, and the average axial rotation was 5.2°. Overall movement of the condyles during gait and ramp-down activity was small. No incidence of condylar lift-off was observed. ConclusionSubjects in this study experienced consistent magnitudes of posterior femoral rollback and external rotation of the femur with weight-bearing flexion. The variation is similar to that previously reported for normal knee where the lateral condyle moves consistently posterior compared to the medial condyle. Subjects experienced low overall mid-flexion paradoxical anterior sliding and no incidence of condylar lift-off leading to mid-flexion stability.

Age-Related Changes in In-Vivo 3D Knee Kinematics during Knee Joint Flexion Observed using 2D/3D Registration Technique

We aimed to identify 3D motion differences in knee joint articular surface kinematics in healthy young and old participants during weight-bearing knee flexion. Twelve healthy male volunteers, six in their 60s and six in their 20s, without any musculoskeletal system disease involving the knees participated. 3D bone models of the femur and tibia were obtained using CT and matched into the fluoroscopic images captured during split squatting. Translation and rotation of the tibia to the femur during weight-bearing flexion were compared between the groups. Translation of the nearest medial-lateral articular surface location and rotational angle of medial-lateral connecting lines were also compared. As the tibial internal-external rotation angle and medial contact point anterior-posterior translation were significantly correlated between the groups, they could not represent the characteristics of age-related changes. Similar to lateral contact point translation and contact points line angles were significantly different during the initial 10° flexion period. At the 40°-45° knee flexion period, a significant difference was detected in the contact point line angle and in the tibial superior-inferior translation. 3D knee joint kinematic differences between participants in their 20s and 60s, especially during initial and 40°-45° periods, can predict kinematic effects on age-related disease.

In vivo kinematics and ligamentous function of the knee during weight-bearing flexion: an investigation on mid-range flexion of the knee.

To investigate the in vivo femoral condyle motion and synergistic function of the ACL/PCL along the weight-bearing knee flexion. Twenty-two healthy human knees were imaged using a combined MRI and dual fluoroscopic imaging technique during a single-legged lunge (0°-120°). The medial and lateral femoral condyle translation and rotation (measured using geometric center axis-GCA), and the length changes of the ACL/PCL were analyzed at: low (0°-30°), mid-range (30°-90°) and high (90°-120°) flexion of the knee. At low flexion (0°-30°), the strains of the ACL and the posterior-medial bundle of the PCL decreased. The medial condyle showed anterior translation and lateral condyle posterior translation, accompanied with a sharp increase in external GCA rotation (internal tibial rotation). As the knee continued flexion in mid-range (30°-90°), both ACL and PCL were slack (with negative strain values). The medial condyle moved anteriorly before 60° of flexion and then posteriorly, accompanied with a slow increase of GCA rotation. As the knee flexed in high flexion (90°-120°), only the PCL had increasingly strains. Both medial and lateral condyles moved posteriorly with a rather constant GCA rotation. The ACL and PCL were shown to play a reciprocal and synergistic role during knee flexion. Mid-range reciprocal anterior-posterior femoral translation or laxity corresponds to minimal constraints of the ACL and PCL, and may represent a natural motion character of normal knees. The data could be used as a valuable reference when managing the mid-range "instability" and enhancing high flexion capability of the knee after TKAs. Level IV.

Kinematic characteristics of patients with cervical imbalance: a weight-bearing dynamic MRI study.

It is a retrospective analysis of 1806 consecutive cervical magnetic resonance images taken in weight-bearing flexion, neutral, and extension positions. The aim was to identify the kinematic characteristics of patients with cervical imbalance. Additionally, factors were analysed in the neutral position that could predict the characteristics. Little is known about the kinematic characteristics during cervical flexion and extension positions of the patient with cervical imbalance (cervical sagittal vertical axis (cSVA) in neutral position ≥ 40mm). After evaluating the whole images, cervical imbalance group (cSVA ≥ 40mm, n = 43) and matched control group (< 40mm, n = 43) were created using propensity score adjusting for age, gender, and cervical alignment. They were compared for cervical motion, changes in disc bulge, and ligamentum flavum (LF) bulge from flexion to extension. Multinomial logistic regression analysis and receiver operating characteristic curve analysis were calculated to verify the predictive factors and cut-off value of the identified characteristics. There were no significant differences in range of motion and the change in bulged discs. There was significant difference in the presence of LF bulge from flexion to extension (p = 0.023); the incidence of LF bulge increased sharply from neutral to extension in imbalance group, while there was linear increase in control group. The canal diameter (odds ratio = 0.61, p = 0.002) and disc height (odds ratio = 1.60, p = 0.041) showed significant relationship with the segments with LF bulge observed in extension but not in neutral position in the imbalance group; the cut-off values were 10.7mm for canal diameter (sensitivity 82.5%, specificity 66.7%) and 7.1mm for disc height (70.8%, 58.5%). Patients with cervical imbalance had a stark increase in LF bulge from the neutral to extension position. Canal diameter < 10.7mm and disc height > 7.1mm on neutral images may predict the segments with LF bulge observed in extension, but not in the neutral position. II (Diagnostic: individual cross-sectional studies with consistently applied reference standard and blinding). These slides can be retrieved from Electronic Supplementary Material.

Stair Climbing and High Knee Flexion Activities in Bi-Cruciate Retaining Total Knee Arthroplasty: In Vivo Kinematics and Articular Contact Analysis

BackgroundBi-cruciate retaining (BCR) total knee arthroplasty (TKA) preserves both anterior and posterior cruciate ligaments with the potential to restore normal posterior femoral rollback and joint kinematics. However, there is limited information regarding articular contact behavior in the contemporary BCR TKA design during high knee flexion activities. This study aimed to investigate the articular knee contact performance in unilateral BCR TKA patients during strenuous flexion activities. MethodsTwenty-nine unilateral BCR TKA patients were evaluated for both knees during single deep lunges, step-ups, and sit-to-stand (STS) using a validated combined computer tomography and dual fluoroscopic imaging system. Medial and lateral condylar contact positions were quantified during weight-bearing flexion. ResultsContact excursions of the lateral condyle in BCR TKAs were significantly more anteriorly located than the contralateral non-operated knees during STS (−4.9 ± 3.1 vs −9.7 ± 4.6 mm, P < .05), single deep lunge (−5.7 ± 3.2 vs −10.0 ± 4.5 mm, P < .05), and step-ups (−4.8 ± 3.6 vs −9.1 ± 3.9 mm, P < .05). Contact points of BCR TKAs indicated reduced femoral external rotation during STS (2.1 ± 4.8° vs 7.7 ± 5.4°, P < .05), single deep lunges (1.8 ± 4.8° vs 7.0 ± 7.1°, P < .05), and step-ups (0.1 ± 4.1° vs 6.2 ± 4.9°, P < .05). Medial pivoting patterns were observed in only 59%, 56%, and 48% of the BCR TKA knees for step-ups, STS, and single deep lunge, respectively. ConclusionThe contemporary BCR TKA design demonstrated asymmetric femoral rollback, medial translation, as well as lateral pivoting in about half of the patient cohort, suggesting that in vivo tibiofemoral kinematic parameters were not fully restored in BCR patients during strenuous flexion activities.