Surface Water Research Articles

Impact of long-term application of biosolids to surface water nitrogen in a working forest plantation in King County, Washington

Forest fertilization with municipal biosolids has been shown to increase tree growth and enhance forest soils. However, there are concerns that nitrogen from the biosolids could impact surface waters through movement from subsurface flow. Here we analyzed data on soil and surface water nitrogen from a working tree plantation that has used biosolids for over three decades to see if there was evidence of N movement through the soil to surface waters. GIS (Geographic Information System) was used to map application units over time and LiDAR (Light Detection and Ranging) was used to delineate watersheds. The program is located in King County Washington with biosolids provided by the King County Wastewater Treatment program. We assembled records to determine if there is any evidence of movement of NO3− through soils or any enrichment in surface waters. While soils show evidence of NO3− enrichment following biosolids application with cumulative loading rates up to 26 Mg ha−1, this is generally limited to the ’A’ soil horizon and does not increase linearly with increased biosolids loading rates. There was no indication of increased surface water NO3− concentration relative to biosolids application rates, with a small trend of decreasing water NO3− over time. Surface water NO3− concentration was not correlated with the fraction of the watershed area that had been amended with biosolids, and there was no observable increase in surface water NO3− with increased frequency of biosolids applications to the tree plantations. These results suggest that the current biosolids program is sufficiently protective of ground and surface waters. These observations suggest that biosolids application can be conducted on a large scale with multiple benefits and no discernible impact to surface waters.

Dynamic characteristics of refrigerant evaporation temperature in air-water heat source heat pump

In order to improve the problem of reduced heat capacity and unstable heating ability of air source heat pump (ASHP) in the heating mode during the cold season, a heat pump evaporator using air and surface water as a heat source is designed in this paper. A heat transfer unit's calculation model of an air–water heat source evaporator is established. Experimental tests and simulation studies are conducted on the refrigerant evaporation temperature and heat pump heating performance. On this basis, a refrigerant evaporation temperature prediction model is constructed using a multiple linear regression (MLR) model. The trend of refrigerant evaporation temperature under air–water heat source is analyzed by taking the winter meteorological parameters in Xiangtan City as an example. The results show that the air–water heat source heat pump (A-WSHP) has a higher refrigerant evaporation temperature and a smaller temperature fluctuation range than the ASHP. The average values of refrigerant evaporation temperatures under the experimental conditions were 5.3 °C and 4.6 °C, respectively. The temperature fluctuation ranges were 3.8 °C-6.7 °C and 2.8 °C-7.0 °C, respectively. The A-WSHP has higher heating capacity and heating stability. Air temperature, air velocity, water spray temperature and water spray flow rate are all important parameters that affect the refrigerant evaporation temperature of a heat pump. Evaporation temperature changes are positively correlated with these factors. In the refrigerant evaporation temperature prediction model, the air temperature change has the most significant effect on the evaporation temperature, followed by spray water temperature, air velocity, and spray flow rate, whose influence weights are 82.5 %, 38.8 %, 29.4 %, and 25.3 %, respectively. Selecting different temperatures of spray water and adjusting the evaporator's inlet spray flow rate can improve the refrigerant evaporation temperature and heat pump heating stability.

Comparative Microplastic Analysis in Urban Waters Using μ-FTIR And Py-GC-MS: A Case Study in Amsterdam

The contamination of freshwater with microplastics (MPs) has been established globally. While the analysis of MPs has predominantly involved spectroscopic methods for revealing particle numbers, the potential of employing spectroscopy for mass estimation has been underutilized. Consequently, there is a need to enhance our understanding of the mass loads of MPs and ensure the complementarity and comparability of various techniques for accurate quantification. This study presents the first comparative results on urban water samples using micro Fourier-transform infrared (μ-FTIR) imaging and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS) to identify and quantify MPs in both particle numbers and mass concentration. Two sampling campaigns in summer and winter were conducted at 11 locations within the Amsterdam canal network. An advanced in-situ volume-reducing sampling pump was employed to collect MPs from the surface water within the size fraction of 10-300 μm. The analysis revealed MP concentrations within the range of 16 -107 MP/m3, estimated to be 2.0-789 μg/m3 by μ-FTIR imaging and 8.5-754 μg/m3 by Py-GC-MS. The results of the two analysis techniques showed good comparability in terms of the general trends of MP abundances, with variations in polymer compositions due to the inherent inter-methodological differences. Elevated MP concentrations were observed in the city center compared to the suburban areas. In addition, seasonal differences in MP abundances were noted at the locations with high human activity.

Effect of surfactant's charge properties on behavior, physiology, and biochemistry and the release of microcystins of Microcystis aeruginosa

Surfactant pollution is escalatitheng in eutrophic waters, but the effect of surfactant charge properties on the physiological and biochemical properties of toxin-producing microalgae remains inadequately explored. To address this gap, this study explores the effects and mechanisms of three common surfactants―cetyltrimethylammonium bromide (CTAB, cationic), sodium dodecyl sulfate (SDS, anionic), and Triton X-100 (nonionic)―found in surface waters, on the agglomeration behavior, physiological indicators, and Microcystin-LR (MC-LR) release of Microcystis aeruginosa (M. aeruginosa) by using UV-visible spectroscope, Malvern Zetasizer, fluorescence spectrometer, etc. Results suggest that charge properties significantly affect cyanobacterial aggregation and cellular metabolism. The CTAB-treated group demonstrates a ∼5.74 and ∼9.74 times higher aggregation effect compared to Triton X-100 and SDS (300 mg/L for 180 min) due to strong electrostatic attraction. Triton X-100 outperforms CTAB and SDS in polysaccharide extraction, attributed to its higher water solubility and lower critical micelle concentration. CTAB stimulates cyanobacteria to secrete proteins, xanthohumic acid, and humic acids to maintain normal physiological cells. Additionally, the results of SEM and ion content showed that CTAB damages the cell membrane, resulting in a ∼90% increase in the release of intracellular MC-LR without cell disintegration. Ionic analyses confirm that all three surfactants alter cell membrane permeability and disrupt ionic metabolic pathways in microalgae. This study highlights the relationship between the surface charge properties of typical surfactants and the dispersion/agglomeration behavior of cyanobacteria. It provides insights into the impact mechanism of exogenous surfactants on toxic algae production in eutrophic water bodies, offering theoretical references for managing surfactant pollution and treating algae blooms.

Preparation and characterization of cementitious materials from dedioxinized and dechlorinated municipal solid waste incineration fly ash and blast furnace slag

To address the resource utilization issue of MSWI fly ash, a method has been proposed to prepare cementitious materials using harmlessly processed MSWI fly ash (HPFA). After washing and thermal treatment, The physicochemical properties of HPFA were characterized using QXRD, ICP, XRF, and GC-MS. Cementitious materials were prepared using HPFA, gypsum and blast furnace slag (BFS) as raw materials, Through XRD, TG, FTIR, TEM, and SEM-EDS methods, the hydration and hardening characteristics were investigated, and the leaching of heavy metals from solidified materials in simulated surface water and landfill environments was evaluated using ICP-MS. The results indicate that the harmless treatment can effectively reduce the chloride content and dioxins in MSWI FA but still contains heavy metals. The addition of HPFA (10%-50%) can enhance the compressive strength of cementitious materials, accelerate the exothermic process of cement hydration, and increase the total heat release of hydration, implying an improvement in the degree of hydration of the system.HPFA could effectively promote the hydration of gypsum and BFS, resulting in the higher formation of ettringite and C-(A)-S-H（C/S=1，Al/Si=0.3）.The formation of C(Mg/Fe)-(A)-S-H suggests that the Fe-Mg solid solution phase in HPFA may have participated in the hydration reaction. The increased stability of highly cross-linked (Q4) silicate tetrahedral structure with time implies that the material may have good durability. The leaching amount of heavy metals met the standards of Class I surface water in GB3838–2002 and GB5085.3–2007 which implies that the material has environmental safety. This study innovatively provides a preparation path for harmless MSWI fly ash and cementitious material ratios, reveals the hydration mechanism of HPFA in cementitious materials, evaluates the solidification ability of heavy metals, and provides important ideas for the resource utilization of MSWI fly ash.

Isolation and Identification of some fresh Protozoa from surface water sources and taps in Dakahlyia Governorate, Egypt

Isolation and Identification of some fresh Protozoa from surface water sources and taps in Dakahlyia Governorate, Egypt

Water quality evaluation based on water quality index and multiple linear regression: A research on Hanyuan Lake in southern Sichuan Province, China.

This study aims to understand the changes in the water quality of Hanyuan Lake and to show these changes over time. In this study, monthly sampling was conducted at three sampling sites in Hanyuan Lake, and water samples were measured for water quality indicators in the laboratory according to the methods specified in the Environmental Quality Standards for Surface Water (GB3838-2002). Based on the monitoring data from January to December 2019, the WQI comprehensive evaluation method was used to conduct multiple linear stepwise regression analysis, extract key indicators, and establish the WQImin model. The results show that according to the WQI comprehensive evaluation method, the WQI values of Hanyuan Lake are all above 90, and the grade is excellent. The overall water quality of Hanyuan Lake is excellent, and most of the water quality indexes reach the Class I standard in the Environmental Quality Standards for Surface Water (GB3838-2002). WQImin1 (R2 = 0.86, p < 0.001, PE = 4.28) as the best WQImin model. In this study, a model with fewer parameters was established by multiple linear regression method, which is conducive to better monitoring of water quality at monitoring stations while saving costs. PRACTITIONER POINTS: According to the WQI comprehensive evaluation method, the WQI values of Hanyuan Lake are all above 90, the rating is excellent. From January 2019 to September 2020, the monthly change trend of each section is roughly the same, showing a trend of first decreasing, then rising, then decreasing, and finally rising and flattening. The WQImin model was developed to completely describe the change in the water body.

Causes and Impacts of Water Pollution on Various water bodies in the State of Rajasthan, India: A Review

Water quality and water resources make an impression on the social, economic and political advancement of society. With the rapid growth of urbanization and industrialization linked with economic and social needs, the pollution of water has reached a level of no return. Water is defined as harmful for human and aquatic lives when it is become contaminated by unexpected substances such as heavy metals, agricultural and industrial chemicals, hydrocarbon fuels, radioactive materials, sewage, pharmaceutical drugs, and biologic agents such as bacteria, parasites, and viruses. This water is considered polluted or contaminated (Bagul et al. 2015), The problem of water pollution becomes more hazardous in a region where availability of water is critically less like the state of Rajasthan (Coyte et al. 2019). The situation of surface water pollution in arid and semi-arid areas of state is alarming. We know that every living being needs water for their survival. All living being intake water directly or indirectly from various water resources. Intake of polluted water would be harmful for them. Transport of bio-accumulative pollutants to food chain makes the situation more grievous. So, it is the need of the hour to examine the magnitude and range of water pollution in the water bodies, especially in the state like Rajasthan. In the present scenario we can’t prevent water to being polluted totally but the scaling down of pollution is imperative. It is high time to take some steps to educate and spread awareness to the people regarding this alarming issue.

Addressing the Water-Energy-Food Nexus in the context of climate change: the case of Bagré dam in Burkina Faso

The water-energy-food (WEF) nexus concept highlights the interdependencies between water, energy, and food resources. Assessing these interdependencies can lead to a better understanding and their exploitation to improve people's access to water, energy, and food. This study aims to highlight the links between the water resource and the current and future water requirements for agricultural and hydropower production in the context of climate change. The bagré dam which is a multi-usage reservoir located in Burkina Faso is considered as the case study. This dam is used for agricultural production, livestock, and hydroelectricity production. To achieve this objective, the surface water resources of the study area and the different water uses have been first estimaded. Then, a model has been developed and implemented using the Water Evaluation And Planning (WEAP) tool, with the reference year 2020. Finally, the developed model was used to study four relevant plausible scenarios in the Bagré area up to 2050, namely: (1) expansion of irrigated schemes, (2) the drinking water needs of a neighbouring town, (3) climate change effects on the dam's water capacity, and (4) combinaison of the three other scenarios. The results show that all the water requirements for different uses are fully met for all the scenario except the combined scenario by 2050. For this last scenario, the unmet water demands reach up to 100% specially during dry season. So, to improve the coverage rate of water demands for the combined scenario, it is crucial to explore other alternatives such as the use of groundwater and the implementation of best practices in agronomic management.

Assessment of Surface Water Quality Drain Using Various Physicochemical Parameters of Lasara Dhanola Drain, Punjab

Abstract: In this study, observations were carried out in the surface waters of Lasara Dhanola drain of Punjab within to determine water quality. The basic physicochemical variables were used to determine water quality. Taking into account the World Health Organization's drinking water standards and the water quality index (WQI) were used in determining the water quality. In addition, irrigation water quality was examined. Some of the water quality parameters exceed the recommended limit values in all at all sites. According to these values, the Lasara Dhanola drain water belongs to the 'very poor' class in terms of irrigation water quality. According to results of factor analysis, pH, temperature, electrical conductivity, suspended solid matter, biological oxygen demand, total hardness, total alkalinity, calcium, nitrate, chlorides, fluorides and dissolved oxygen are the main variables responsible for the processes in the ecosystem

Inaccessible and Unaffordable? The State of Water and Sanitation Services in Nairobi, Kenya

As the limited water resources become increasingly stressed by factors such as rapid urbanization, population growth, and climate change, the need for sustainable urban water management is more important than in the past decades. A large part of the world’s population still lacks access to clean water and sanitation, making achieving Sustainable Development Goals a challenge. Water is an indispensable resource and plays an important role in ensuring the achievement of Sustainable Development Goals. Therefore, there is a need to prioritize research on the availability, affordability, and access of water resources to promote sustainable water resource management. In this study, we reviewed academic articles and published reports from various institutions and organizations to assess water sources, infrastructure, coverage, accessibility, and affordability of water and sanitation services in Nairobi County. The study identified Nairobi’s main water sources as municipal water, primarily from surface water and groundwater. However, the capacities of the water sources, treatment plants, and wastewater treatment plants were found to be insufficient, resulting in water shortages in most parts of the city.Most of the infrastructures were also found to be insufficient and old, contributing to water distribution inefficiencies, frequent leakages, and pipe bursts which hampers water reliability. The study suggests prioritizing the water and sanitation sector in government budgets to increase infrastructure development investments and funding. Appropriate wastewater treatment methods should also be adopted and implemented to enable wastewater to meet water consumption standards and be potentially integrated into supply systems.

Resource classification of coal bed methane and its contribution in energy transition and decarbonization path of oil and gas industry (A synopsis of CBM Life Cycle Analysis)

World economies are becoming increasingly more dependent on energy and countries have a voracious appetite for energy therefore, the need for an abundant clean energy is becoming a necessity. Energy companies are challenging environmental costs of coal bed methane as with advancement of new technology the impact from production of coal bed methane can reduce and to a certain extent avoided or offset. Production of coal bed methane results in changes to the land, to surface water and to ground water systems. Carbon quantification is required to understand, monitor and manage these changes. Previous life cycle analysis for this resource class has lack of process design details because of which there is a knowledge gap in understanding of emission profile of coal bed methane’s production. The objective of this study is to add value and reduce the scientific gap with respect to the production techniques of coal bed methane and its environmental impact. Removal of water continuously from coal seams depletes ground water and may eventually lower surface water flows (streams and rivers). It can also change the flow of groundwater drawing fresh water into the coal seams. To better understand this phenomenon the work establishes the Coal Bed Methane production foundation by in depth understanding of · Coal Bed Methane reservoir types; · Coal Bed Methane depositional environment, generation, and geological distributions; · Coal Bed Methane resource energy supply methods by understanding its construction, production and processing. The study then uses Life Cycle Assessment approach and understands previous emission numbers of Coal Bed Methane’s resource development. The work does systematic analysis and summarizes the previously published Life Cycle Analysis to understand further the potential environmental impacts of resource development of Coal Bed Methane. This will help energy companies to understand the field development, production, and operations of coal bed methane’s resource in terms of carbon numbers thereby optimizing the operations through carbon management thus reducing the potential impacts.

Assessment of microbial properties, and heavy metals contents of surface water and ground water samples In Ureje and Ireje, Ekiti State, Nigeria.

Water is everywhere, · it is the most basic and necessary element of life, as well as the most important and abundant compound in the ecosystem. Standard methods were used to evaluate the physicochemical properties, microbial properties, and heavy metal content of river and well water samples in Ekiti State, South-West Nigeria. Important parameter like pH, electrical conductivity, total dissolved solids, DO, BOD, turbidity, total alkalinity, total hardness, heavy metals and microbial properties are determined. The research work indicated that temperature, odour, pH, alkalinity, TDS, biochemical oxygen demand, DO, chloride, nitrate and turbidity were within the range of WHO permissible limits for drinking water while color, Conductivity, iron and manganese were above the WHO permissible limits. The study also indicated that the microbial contents such as total viable count, yeast/mold and coliform were above the WHO permissible limits for drinking. These results show that the water sources were slightly contaminated and unsafe for human consumption. This water must be treated before it may be consumed or used for domestic application.

Distribution, source identification, water quality, and risk assessment of trace elements in the surface-groundwater-sediments multifunctional system in Guohe River Basin

Within the Huaihe River Basin, Guohe River, as its second-largest tributary, serves as a critical water supply source. Recent industrial and agricultural advancements have led to increased trace element contamination, adversely impacting the water quality within Guohe River Basin. Therefore, this study aimed to investigate the distribution characteristics, sources, water quality and risk assessment of trace elements in the surface water, groundwater, and sediments across the basin. The results showed that the spatial distribution of trace elements in the surface water and groundwater of Guohe River Basin was that most of the high concentrations appeared in Qiaocheng District of Bozhou City, the mean concentration of Fe in Guohe River sediments was the highest, the mean concentration of Sb was the lowest. The PMF source analysis results showed that the main source of trace elements in Guohe River Basin was natural geological processes, followed by human activities. The sodium adsorption ratio (SAR) indicated that the surface water samples of Guohe River in two seasons had high sodium and salinity hazards. The water quality index (WQI) showed that surface water and groundwater samples in the northwestern of Guohe River Basin had poor water quality. The results of the risk assessment showed that As and Mn posed great ecological risks to surface water and groundwater, respectively, and that F− was the pollutant with the most potential health risk hazard in the basin. The Geo-accumulation index (Igeo) results showed that Cd, Se and As should be taken seriously as the main contaminants of the sediments in Guohe River Basin. KeywardsTrace elements; Source analysis; Sodium adsorption ratio; Water quality index; Risk assessment; Geo-accumulation index.

High enrichment factors in chemical analysis of progestins and in bioassays: insights beyond trace levels.

Concerns are growing about adverse effects of progestins on biota, even at ultra-trace concentrations. The enrichment factor (EF) from extraction of analytes in environmental samples that is needed for sample pre-concentration can affect not only performance of the analytical method but also the matrix effect. Therefore, the present study aimed to assess the influence of high sample EF on performance of the high-performance liquid chromatography with atmospheric pressure chemical ionization and photoionization coupled with high-resolution mass spectrometry (HPLC-APCI/APPI-HRMS) method for analysis of progestins in waste water treatment plant (WWTP) effluents and surface waters and analysis of (anti-)progestogenic activities measured by (anti-)PR-CALUX bioassays. The results showed that HPLC-APCI/APPI-HRMS coupled with solid-phase extraction and a high EF (33,333 Lwater/Lextract) enabled the detection of more compounds compared to samples with lower sample EF (10,000 Lwater/Lextract). The matrix effect did not increase proportionally compared to lower EFs (10,000 and 16,666 Lwater/Lextract), and lower limits of quantification were achieved in WWTP effluents and surface waters. The results of bioassays have shown that relative EF of 25 Lwater/Lbioassay appears high enough to detect progestogenic activity in treated waste water. Our study is one of the first to provide insights into sample pre-concentration in analysis of progestins and progestogenicity in aquatic environments.

Assessing petroleum contamination in parts of the Niger Delta based on a sub-catchment delineated field assessment.

The Niger Delta in Nigeria is a complex and heavily contaminated area with over 150,000 interconnected contaminated sites. This intricate issue is compounded by the region's strong hydrological processes and high-energy environment, necessitating a science-based approach for effective contamination assessment and management. This study introduces the concept of sub-catchment contamination assessment and management, providing an overarching perspective rather than addressing each site individually. A description of the sub-catchment delineation process using the digital elevation model data from an impacted area within the Delta is provided. Additionally, the contamination status from the delineated sub-catchment is reported. Sediment, surface water and groundwater samples from the sub-catchment were analyzed for total petroleum hydrocarbons (TPH) and polycyclic aromatic hydrocarbons (PAHs), respectively. Surface sediment TPH concentrations ranged from 129 to 20,600mg/kg, with subsurface (2-m depth) concentrations from 15.5 to 729mg/kg. PAHs in surface and subsurface sediment reached 9.55mg/kg and 0.46mg/kg, respectively. Surface water exhibited TPH concentrations from 10 to 620mg/L, while PAHs ranged from below detection limits to 1mg/L. Groundwater TPH concentrations spanned 3 to 473mg/L, with total PAHs varying from below detection limits to 0.28mg/L. These elevated TPH and PAH levels indicate extensive petroleum contamination in the investigated sediment and water environment. Along with severe impacts on large areas of mangroves and wetlands, comparison of TPH and PAH concentrations with sediment and water quality criteria found 54 to 100% of stations demonstrated exceedances, suggesting adverse biological effects on aquatic and sediment biota are likely occurring.

Groundwater suitability assessment for irrigation and drinking purposes by integrating spatial analysis, machine learning, water quality index, and health risk model.

An in-depth understanding of nitrate-contaminated surface water and groundwater quality and associated risks is important for groundwater management. Hydrochemical characteristics and driving forces of groundwater quality and non-carcinogenic risks of nitrate were revealed by the integrated approaches of self-organizing map analysis, spatial visualization by geography information system, entropy and irrigation water quality indices, and human health risk model. Groundwater samples were categorized into two clusters by SOM analysis. Cluster I including three samples were Ca-SO4 type and cluster II of remaining 136 samples were Ca-HCO3 type. Hydrochemical compositions of two cluster samples were dominated by water-rock interaction: (1) calcite and gypsum dissolution for cluster I samples and (2) calcite dissolution, silicate weathering, and positive cation exchange for cluster II samples. Nitrate contamination occurred in both cluster I and II samples, primarily induced by agricultural nitrogen fertilizer. The EWQI results showed that 90.97% in total groundwater samples were suitable for drinking purpose, while the IWQI results demonstrated that 65.03% in total groundwater samples were appropriate for irrigation purpose. The HHR model and Monte Carlo simulation indicated that the non-carcinogenic nitrated risk was highest in children. Exposure frequency was the most sensitive factor (86.33% in total) influencing the total non-carcinogenic risk, indicated by sensitivity analysis. Compared with the two clusters of groundwater, surface water has a shorter circulation cycle and lower ion concentrations resulting in better water quality. This study can provide scientific basis for groundwater quality evaluation in other parts of the world.

Challenges of Undular Jump Modelling

The study of open channel flow hydraulics extends beyond supercritical and subcritical flow states to include a distinct state known as near-critical flows. This category encompasses various hydraulic phenomena, with some of the most notable being solitary waves, cnoidal waves, and undular jumps. This paper specifically addresses the phenomenon of undular jumps, providing a brief overview of its characteristics and discussing instances of undular jump formation in natural rivers settings and during the operation of various hydraulic structures. When there is a sudden change in flow depth from a lower level to a higher one, it typically leads to a sudden increase in the water surface, known as a hydraulic jump. However, if the jump is relatively small, meaning the depth change is minor, the water does not rise noticeably and abruptly. Instead, it will traverse from the lower to the higher stage through a sequence of gradually diminishing undulations that extend over a considerable distance. Such phenomenon is called an undular jump.The occurrence of undular hydraulic jumps can be observed in various open channels such as irrigation and water supply channels, beneath vertical sluice gates, within estuaries during specific tide periods, and in narrow or shallow passages affected by strong currents. Additionally, this phenomenon often manifests downstream of low drop structures or in transitional zones from steep to gently sloping channels. In channels where undular jumps occur, waves with significant amplitudes develop and travel downstream of the jump. Accounting for the propagation of these downstream free-surface waves is essential for canal design and natural channel maintenance. The wave height serves as a crucial design parameter that dictates the necessary sidewall height of the canal. In natural channels, the embankment height must exceed the crest of the free-surface undulations to prevent overtopping and subsequent erosion, which could ultimately lead to bank destruction. Moreover, the propagation of free-surface waves may subject downstream canal structures, such as gates, locks, and weirs, to additional impact loads, perturbations, and vibrations.In recent years, different scientists have made various attempts to investigate and describe this phenomenon using physical, mathematical and computer modelling. However, this phenomenon has a number of peculiarities that are not always taken into account. An objective of this article is to present the particularities of different type of undular jump modelling and to compare the obtain results.

Quali-quantitative water behaviour in an intensive swine production catchment in the Atlantic Forest biome, Southern Brazil.

Agriculture is an essential economic activity in Brazil. However, it is also the main source of water quality degradation. Monitoring catchments with agricultural land use is a way to generate information on a scale to identify causes and sources of water quality degradation. This work used monitoring data derived from hydrology and the quality of surface and underground water in an intensive agricultural catchment in the Atlantic Forest biome. The Fortaleza River catchment is located in the western part of Santa Catarina state in southern Brazil and has 62 km2 of drainage area. Hydrological and water quality monitoring was conducted for 7years at two fluviometric stations, three lysimeters, one meteorological station, and one piezometer. Data on precipitation, temperature, water flow, surface runoff, drainage, and water quality were used. Statistical analyses were also developed. Precipitation between 2013 and 2019 presented a homogeneous distribution in monthly and annual data, with January and July the months with the highest and lowest values, respectively. Statistical difference in the average and Q95 flows was found in upstream and downstream fluviometric sections. In terms of quality, statistical differences were identified for ammonium, nitrate, and potassium concentrations, which had higher concentrations in lysimeter runoff, indicating direct influence of agricultural activity on water quality. Principal component analysis (PCA) indicated that (i) surface water presented a positive relationship in Component 1 for the magnesium-calcium, sulphate-chloride, and acetate-bromide groups and a negative relationship for phosphate-nitrate; (ii) in lysimeters, the positive relationship occurred for Component 2 for the phosphate-chloride and sulphate-nitrate groups and was negative for ammonium-lithium and calcium-potassium-magnesium; and (iii) in piezometer, positive relationships were found for chloride-sodium and phosphate-nitrite pairs, while negative relationships were found for calcium-magnesium.

Evaluation of Water and Sediment Quality in Lake Mogan, Türkiye

The wetlands, with their delicate ecosystems, play a crucial role in regulating water regimes and supporting diverse plant and animal communities, particularly those associated with water habitats. Mogan Lake, located within the Gölbaşı Special Environmental Protection Area, stands out as a unique habitat, hosting over 200 bird species. This study aimed to assess the current water quality of Mogan Lake by analysing various water quality variables. Three sampling sites, representing the northern, middle, and southern parts of the lake, were selected to examine both surface water and bottom sludge characteristics through the analysis of 29 pollutant variables. Water samples were collected from 30 cm beneath the water surface and 50 cm above the bottom of the lake. Sediment samples were collected from the sludge at the lake basin. Additionally, to understand their impact on the lake’s water quality, 26 pollutants were also measured in water samples taken from the five main streams that feed the lake. The results reveal a significant level of organic pollution in the lake, along with elevated nitrogen levels indicating hypertrophic conditions. Although organic pollutants were detected in the lake bottom sediment through analysis, they are considered non-hazardous in terms of heavy metals and other inorganic variables.