Wastewater Treatment Plants In Germany Research Articles

Towards carbon neutrality and circular economy: an innovative combination of enhanced biogas production and nutrient recovery from sludge dewatering liquor at a municipal wastewater treatment plant in Germany.

An innovative circular economy (CE) system was implemented at the wastewater treatment plant (WWTP) in Brunswick. The performance of the CE system was evaluated for 4 years: the thermal pressure hydrolysis enhanced the methane production by 18% and increased the digestate dewaterability by 14%. Refractory COD formed in thermal hydrolysis and increased the COD concentration in the WWTP effluent by 4 mg L-1 while still complying with the legal threshold. Struvite production reached high phosphorus recovery rates of >80% with a Mg:P molar ratio ≥0.8. Nitrogen was successfully recovered as ammonium sulfate with high recovery rates of 85-97%. The chemical analyses of secondary fertilizers showed a low pollutant content, posing low risks to soil and groundwater ecosystems. The total carbon footprint of the WWTP decreased due to enhanced biogas production, the recovery of renewable fertilizers and a further reduction of nitrous oxide emissions. Using green energy will be crucial to reach carbon neutrality for the entire WWTP.

Reduction in the Input of Microplastics into the Aquatic Environment via Wastewater Treatment Plants in Germany

Microplastic (MP) has emerged as a significant environmental challenge due to increased plastic production and its widespread presence in the environment. This study aimed to assess MP concentrations throughout the treatment process at nine wastewater treatment plants (WWTPs) in Germany, from influent to effluent. A customized sampling technique was employed, followed by field and laboratory preparation and the quantification of polymers (PE, PP, PS, PMMA, and PET) using TED-GCMS. MP concentrations decreased progressively in the WWTPs, with influent concentrations ranging from 2.5 to 13.6 mg/L. Effluent concentrations in the conventional WWTPs ranged from 0.001 to 0.051 mg/L, while advanced treatment via filtration yielded concentrations below the limit of quantification at 0.005 mg/L. All tested of the WWTPs demonstrated an over 99% removal efficiency for microplastics. Despite effective retention by the WWTPs, a critical evaluation of the results is necessary. There is a need to optimize existing technologies and enhance the standardization of sampling, processing, and measurement methods, as well as intensify efforts towards creating preventive measures to reduce plastic emissions.

Simultaneous identification and quantification of three water-soluble polymers (PVP, PNVCL and PEI) in wastewater samples by continuous-flow off-line pyrolysis GC/MS

In environmental analysis, the detection of water-soluble synthetic polymers (WSSP) presents considerable challenges. Thus, a precise and reproducible analytical method was developed using continuous-flow off-line pyrolysis with gas chromatography/mass spectrometry (GC/MS) to simultaneously identify multiple water-soluble polymers from a single environmental sample.WSSP are widely used in multiple industries as hydrogels due to their hydrophilic character and potential biocompatibility. This adaptability of hydrogels is reflected in their ability to provide customized formulations for specific needs, such as in the development of personal care products, medicine, and pharmaceuticals.Specifically, polyvinylpyrrolidone (PVP), poly(N-vinylcaprolactam) (PNVCL), and polyethyleneimine (PEI) were targeted for analysis in wastewater, employing unique pyrolysis products for identification. These polymers require careful assessment in wastewater to evaluate potential environmental risks associated with their release.PVP and PNVCL were identified through two pyrolysis products, while six pyrolysis products were utilized for the identification of PEI.The validated method demonstrated very good linearity and reproducibility, with correlation coefficients ranging from 0.94 to 0.99 and relative standard deviation (RSD) values between 3 % and 36 % for the targeted compounds. The limit of quantification (LOQ) for the three polymers ranged from 1 to 10 μg L-1. Moreover, the average recovery rates for these polymers, determined from artificial water samples, were approx. 85 %.Utilizing the validated method, water samples from seven wastewater treatment plants in Germany were successfully analyzed, confirming the presence of these polymers at elevated concentrations in the μg L-1 range. Notably, untreated influent waters exhibited higher polymer levels compared to treated influents and effluents, underscoring their significant contribution to overall polymer content.The developed analytical method provides an efficient tool for the simultaneous identification and quantification of PVP, PNVCL, and PEI in wastewater samples. The results highlighted the prevalent presence of PVP, PNVCL, and PEI in the tested wastewater samples, indicating their significant abundance.

The role of stormwater infrastructure in regional methane emissions.

Stormwater infrastructure has been recently indicated as a potential hotspot for methane (CH4) emissions. Although local assessments based on direct CH4 measurements are increasingly available, there is currently no standardized approach for evaluating CH4 emissions from different types of stormwater infrastructure, including permanently impounded or fast-draining structures in Urban Drainage Systems (UDS). Therefore, a comparative analysis with wastewater infrastructure systems, such as wastewater treatment plants (WWTPs), is not yet possible. Here, we present a conceptual framework for the first-order quantification and upscaling of CH4 emissions from stormwater infrastructure at local and national scales. We combined in-situ and ex-situ measurements of CH4 emissions with purposely acquired data from selected stormwater facilities to provide initial estimates of CH4 emissions and emission factors for stormwater infrastructure in Germany. The results show that while stormwater infrastructure might emit comparable amounts of CH4 per area as natural and anthropogenically impacted inland waters, it may exhibit higher mean emission factors (up to 7 times) than conventional WWTPs, indicating less efficiency in limiting CH4 emissions than WWTPs. This is particularly true for permanently impounded facilities, which showed substantially higher mean surface CH4 emissions (up to 632mg m-2 d-1) than fast-draining infrastructure (0.5-1.28mg m-2 d-1). Permanently impounded sedimentation basins for stormwater management alone may reach up to 60% of the total CH4 emissions originating from WWTPs in Germany. These results are in conflict with the ongoing trend towards increasing implementation of impounded stormwater infrastructure systems, highlighting the urgent need for more extensive assessments of their impact on CH4 dynamics.

Determination of the water-soluble polymer poly(ethyleneimine) (PEI) in wastewater by continuous-flow off-line pyrolysis GC/MS

Reliable identification and quantification of water-soluble synthetic polymers (WSSP), such as polyethyleneimine (PEI), is crucial for understanding their potential impact on certain ecological environments. Therefore, this study proposes an analytical method combining on-line and off-line pyrolysis GC/MS to investigate the pyrolytic degradation. mechanism of branched PEI and develop a calibration method using specific pyrolysis. products, including methylpyrazine, dimethylpyrazine, ethylmethylpyrazine, trimethylpyrazine, methylpropylpyrazine and ethyldimethylpyrazine, for the. quantification of PEI in environmental wastewater samples. The developed analytical. method shows adequate linearity for all molecular ions of the specific pyrolysis. products, with a determination coefficient ranging from 0.95 to 0.98 for the range of 10–500 μg PEI. The limit of quantification for this method lies between 1 and 10 μg/L of PEI. The accuracy (absolute recovery 71–95%) and reproducibility (RSD < 30%) were. evaluated by multiple spiking/recovery experiments at a PEI level of 500 μg. Using this. method for samples collected from different wastewater treatment plants in Germany. reveals a significant emission of PEI to the aquatic environment with concentrations. ranging from 0.08 mg L-1–0.55 mg L-1, and thus demonstrating its applicability in. environmental studies. To the best of our knowledge, this is the first report on the. occurrence of PEI in environmental samples.

Kemira, Veolia pursue phosphorus recovery

The French water management company Veolia and the Finnish chemical maker Kemira are working together to deploy a technology that recovers phosphorus from sewage sludge. The companies plan to conduct a pilot-scale trial at a wastewater treatment plant in Germany later this year. The technology uses magnets to separate the iron phosphate mineral vivianite from sludge that has gone through anaerobic digestion. The companies hope that the recovered phosphorus can be used to make fertilizers, which Europe usually has to import .

Microplastic sampling from wastewater treatment plant effluents: Best-practices and synergies between thermoanalytical and spectroscopic analysis

Wastewater treatment plants (WWTPs) may represent point sources for microplastic discharge into the environment. Quantification of microplastic in effluents of WWTPs has been targeted by several studies although standardized methods are missing to enable a comparability of results. This study discusses theoretical and practical perspectives on best practices for microplastic sampling campaigns of WWTPs. One focus of the study was the potential for synergies between thermoanalytical and spectroscopic analysis to gain more representative sampling using the complementary information provided by the different analytical techniques. Samples were obtained before and after sand filtration from two WWTPs in Germany using cascade filtration with size classes of 5,000 – 100 µm, 100 – 50 µm, and 50 – 10 µm. For spectroscopic methods samples were treated by a Fenton process to remove natural organic matter, whereas TED-GC-MS required only sample extraction from the filter cascade. µFTIR spectroscopy was used for the 100 µm and 50 µm basket filters and µRaman spectroscopy was applied to analyze particles on the smallest basket filter (10 µm). TED-GC-MS was used for all size classes as it is size independent. All techniques showed a similar trend, where PE was consistently the most prominent polymer in WWTP effluents. Based on this insight, PE was chosen as surrogate polymer to investigate whether it can describe the total polymer removal efficiency of tertiary sand filters. The results revealed no significant difference (ANOVA) between retention efficiencies of tertiary sand filtration obtained using only PE and by analyzing all possible polymers with µFTIR and µRaman spectroscopy. Findings from this study provide valuable insights on advantages and limitations of cascade filtration, the benefit of complementary analyses, a suitable design for future experimental approaches, and recommendations for future investigations.

Мембранные биореакторы: опыт применения в зарубежных странах

This article addresses advanced methods of wastewater treatment, which presents an urgent global problem. The use of membranes or so-called membrane bioreactors (MBR) at treatment facilities comprises an efficient method of wastewater treatment. The characteristics of membrane designs along with their practical advantages and disadvantages are considered. Examples of using MBR at wastewater treatment plants in Germany, Italy and Sweden are examined. A recently developed MBR technology based on filtration through micro- or ultrafiltration membranes is gaining in popularity. In such technologies, the high quality of treated water is achieved due to the MBR design, which increases both the concentration of activated sludge in the bioreactor and its filtering capacity. Over 100 years of contemporary residential and industrial wastewater treatment, no other implemented technology has exhibited as many positive effects. Due to the wide range of available membranes and modules, suitable systems can be found for almost any type of water treatment application. In addition, these membranes are compact, which becomes an advantage when clearing areas for new construction or when the expansion of a wastewater treatment plant is limited.

In situ Prokaryotic and Eukaryotic Communities on Microplastic Particles in a Small Headwater Stream in Germany.

The ubiquitous use of plastic products in our daily life is often accompanied by improper disposal. The first interactions of plastics with organisms in the environment occur by overgrowth or biofilm formation on the particle surface, which can facilitate the ingestion by animals. In order to elucidate the colonization of plastic particles by prokaryotic and eukaryotic microorganisms in situ, we investigated microbial communities in biofilms on four different polymer types and on mineral particles in a small headwater stream 500 m downstream of a wastewater treatment plant in Germany. Microplastic and mineral particles were exposed to the free-flowing water for 4 weeks in spring and in summer. The microbial composition of the developing biofilm was analyzed by 16S and 18S amplicon sequencing. Despite the expected seasonal differences in the microbial composition of pro- and eukaryotic communities, we repeatedly observed polymer type-specific differentiation in both seasons. The order of polymer type-specific prokaryotic and eukaryotic community distances calculated by Robust Aitchison principal component analysis (PCA) was the same in spring and summer samples. However, the magnitude of the distance differed considerably between polymer types. Prokaryotic communities on polyethylene particles exhibited the most considerable difference to other particles in summer, while eukaryotic communities on polypropylene particles showed the most considerable difference to other spring samples. The most contributing bacterial taxa to the polyethylene-specific differentiation belong to the Planctomycetales, Saccharimonadales, Bryobacterales, uncultured Acidiomicrobia, and Gemmatimonadales. The most remarkable differences in eukaryotic microorganism abundances could be observed in several distinct groups of Ciliophora (ciliates) and Chlorophytes (green algae). Prediction of community functions from taxonomic abundances revealed differences between spring and summer, and – to a lesser extent – also between polymer types and mineral surfaces. Our results show that different microplastic particles were colonized by different biofilm communities. These findings may be used for advanced experimental designs to investigate the role of microorganisms on the fate of microplastic particles in freshwater ecosystems.

Antibiotic Resistance in Wastewater Treatment Plants and Transmission Risks for Employees and Residents: The Concept of the AWARE Study.

Antibiotic resistance has become a serious global health threat. Wastewater treatment plants may become unintentional collection points for bacteria resistant to antimicrobials. Little is known about the transmission of antibiotic resistance from wastewater treatment plants to humans, most importantly to wastewater treatment plant workers and residents living in the vicinity. We aim to deliver precise information about the methods used in the AWARE (Antibiotic Resistance in Wastewater: Transmission Risks for Employees and Residents around Wastewater Treatment Plants) study. Within the AWARE study, we gathered data on the prevalence of two antibiotic resistance phenotypes, ESBL-producing E. coli and carbapenemase-producing Enterobacteriaceae, as well as on their corresponding antibiotic resistance genes isolated from air, water, and sewage samples taken from inside and outside of different wastewater treatment plants in Germany, the Netherlands, and Romania. Additionally, we analysed stool samples of wastewater treatment plant workers, nearby residents, and members of a comparison group living ≥1000 m away from the closest WWTP. To our knowledge, this is the first study investigating the potential spread of ESBL-producing E. coli, carbapenemase-producing Enterobacteriaceae, and antibiotic resistance genes from WWTPs to workers, the environment, and nearby residents. Quantifying the contribution of different wastewater treatment processes to the removal efficiency of ESBL-producing E. coli, carbapenemase-producing Enterobacteriaceae, and antibiotic resistance genes will provide us with evidence-based support for possible mitigation strategies.

Life cycle assessment of prospective sewage sludge treatment paths in Germany

Due to the amendment of the sewage sludge ordinance, both a thermal post-treatment and a phosphorous recovery from sewage sludge will become mandatory for large-scale wastewater treatment plants in Germany. This study analyzed four prospective treatment paths for sewage sludge by means of life cycle assessment. In the realm of a gate-to-cradle approach, environmental impacts were quantified for all compartments of the ReCiPe Midpoint (H) 2016 method.The spreading of digested sludge on agricultural soils was considered as the base case (system: AD + spreading). It was compared to the centralized incineration of sludge (system: AD + I), a decentralized hydrothermal carbonization followed by centralized incineration (system: AD + HTC + I) and a decentralized pyrolysis of sludge followed by centralized incineration (system: AD + P + I). For all cases, phosphorous recovery from the ash was included. A comparative evaluation showed that AD + spreading resulted in least environmental impacts in most categories but was subject to a high local immission potential due to sewage sludge spreading. It was found to be only justifiable, if toxicity and eutrophication were not compromised. Alternatively, a thermal post-treatment step is required. Hereby, AD + I and AD + HTC + I showed the overall least environmental impacts, while AD + P + I was characterized by similar or higher environmental impacts throughout all impact categories.Alongside the comparative analysis, a hotspot analysis was carried out and mitigation potentials were identified. For all thermochemical post-treatment paths, it was derived that (i) the share of fossil external energy must be kept to a minimum, (ii) primary or secondary measures to control N2O emissions during the incineration and pyrolysis should be implemented and (iii) the technological approach to recover phosphorous must be carefully selected.

Liquid chromatography/mass spectrometry analytical determination of gabapentin transformation products by heterogeneous photocatalysis and environmental evaluation.

Gabapentin is a drug used to treat epilepsy and peripheral neuropathic pain. It is an analog of gamma-aminobutyric acid, and it is a selective blocker of voltage-gated calcium channels. The drug is excreted unmetabolized; it is stable in the environment and is classified as a persistent mobile organic contaminant. Because wastewater treatment plants (WWTPs) are not completely efficient, some bioactive molecules may be released unaltered into the environment. The aim of this study was to provide information about degradation pathways of gabapentin in water by studying its photoinduced transformation products (TPs) through laboratory simulation experiments. Gabapentin and its TPs were monitored in influent and effluent water samples from WWTPs in Germany and Italy. The laboratory simulation used heterogeneous photodegradation mediated by titanium dioxide (TiO2 ). Chromatographic separation was achieved using a C18 reverse-phase column, and the structural identification of TPs was performed using high-resolution electrospray ionization high-resolution mass spectrometry (ESI-HRMS) and multistage MSn experiments. Several TPs were observed during TiO2 photodegradation. Nine new compounds were detected, and potential structures were assigned by studying the fragmentation pathways of the [M + H]+ ions of these TPs and gabapentin. Gabapentin and some of the newly identified TPs were found in environmental samples from WWTPs. The developed high-performance liquid chromatography/high-resolution mass spectrometry method was used to identify TPs from gabapentin. It was then successfully applied to real environmental samples to monitor the TPs as potential environmental pollutants.

Microplastic particle emission from wastewater treatment plant effluents into river networks in Germany: Loads, spatial patterns of concentrations and potential toxicity

Wastewater treatment plants (WWTP) are considered to be a point source of microplastic (particles <5 mm) for riverine environments. However, data on microplastic effluent concentrations in WWTPs is collected with a broad range of methods, which impede comparisons across data sets. We provide an estimate of the annual emissions of microplastic particles by WWTPs into the ten major river basins of Germany. We analyze the concentration patterns of microplastics among different stream orders resulting from the spatial organization of WWTPs along the river network. The local in-stream microplastic concentrations are estimated through a network model that accounts for routing of microplastics through the entire fluvial network under the assumption of no losses by sedimentation, entanglement or degradation. Previous studies have observed microplastic concentrations in treated WWTPs effluents ranging several orders of magnitude. In 19 studies reviewed (2016–2020), the concentrations of observed microplastic concentrations (size range between 10 and 5000 μm) in 79 WWTP effluents ranged between 4 ∗ 100 and 4.5 ∗ 105 items/m3 with a median of around 6400 items/m3. The total, median microplastic load emitted by WWTPs in Germany is 7 ∗ 1012 items/year. The simulated microplastic concentrations, on average, tend to increase with increasing stream order suggesting that the WWTP effluent fraction accumulates with a higher rate than discharge. Simulated WWTP-derived in-stream concentrations are higher than observed concentrations with all sources of microplastic, not only those from WWTPs. Observed microplastic concentrations in rivers as well as the considerably higher simulated, WWTP-derived microplastic concentration, even for low flow conditions, are approximately one order of magnitude below currently known toxic effect levels.

Ammonium recovery from process water of digested sludge dewatering by membrane contactors

Abstract Membrane contactors are a promising alternative for nitrogen removal and recovery from process water compared to other physicochemical and biological sidestream treatment processes. Münster wastewater treatment plant (WWTP) is the first municipal WWTP in Germany operating a full-scale membrane contactor system to improve the nitrogen elimination and recovery efficiency. Factors influencing the operation and membrane performance are investigated in an accompanying research project. Additional operational aspects of the applied membrane modules are investigated in detail using a bench-scale membrane contactor. First results of the full-scale application demonstrate a high nitrogen removal efficiency of &amp;gt;95%.

Winter is coming – Impact of temperature on the variation of beta-lactamase and mcr genes in a wastewater treatment plant

Wastewater treatment plants (WWTP) play a key role in the dissemination of antibiotic resistance and analyzing the abundance of antibiotic resistance genes (ARGs) and resistant bacteria is necessary to evaluate the risk of proliferation caused by WWTPs. Since few studies investigated the seasonal variation of antibiotic resistance, this study aimed to determine the abundance of beta-lactamase and mcr genes and to characterize phenotypic resistant strains in a WWTP in Germany over the seasons. Wastewater, sewage sludge and effluent samples were collected over a one year period and analyzed using quantitative real-time PCR. Resistant strains were isolated, followed by identification and antibiotic susceptibility testing using VITEK 2. The results show a significantly higher occurrence of nearly all investigated ARGs in the wastewater compared to sewage sludge and effluent. ARG abundance and temperature showed a negative correlation in wastewater and significant differences between ARG abundance during warmer and colder seasons were determined, indicating a seasonal effect. Co-occurrence of mcr-1 and carbapenemase genes in a multi-drug resistant Enterobacter cloacae and Escherichia coli producing extended-spectrum beta-lactamase (ESBL) was determined. To the best of our knowledge, this is the first detection of mcr-1, blaVIM and blaOXA-48 in an ESBL-producing E. coli. Although wastewater treatment reduced the abundance of ARGs and resistant strains, a dissemination into the river might be possible because carbapenemase-, CTX-M- and mcr-1-gene harboring strains were still present in the effluent.

Spatial Organization of Human Population and Wastewater Treatment Plants in Urbanized River Basins

AbstractDischarge from multiple wastewater treatment plants (WWTPs) distributed in urbanized river basins contributes to impairments of river water‐quality and aquatic ecosystem integrity, with size and location of WWTPs determined by population distribution within a river basin. Here we used geo‐referenced data for WWTPs in Germany to investigate the spatial organization of three attributes of interest in this study: population, population equivalents (the aggregated population served by each WWTP), and the number/sizes of WWTPs. To this end, we selected as case studies three large urbanized river basins (Weser, Elbe, and Rhine), home to about 70% of the population in Germany. We employed fractal river networks as structural platforms to examine the spatial patterns from two perspectives: spatial hierarchy (stream order) and patterns along longitudinal flow paths (width function). Moreover, we proposed three dimensionless scaling indices to quantify (1) human settlement preferences by stream order, (2) non‐sanitary flow contribution to total wastewater treated at WWTPs, and (3) degree of centralization in WWTPs locations. Across the three river basins, we found scale‐invariant distributions for each of the three attributes with stream order, quantified using extended Horton scaling ratios. We found a weak downstream clustering of population in the three basins. Variations in population equivalent clustering among different class‐sizes of WWTPs reflected the size, number, and locations of urban agglomerations in these river basins. We discussed the applicability of this approach to other large urbanized basins to analyze spatial organization of population and WWTPs.

Successful strategies for increasing energy self-sufficiency at Grüneck wastewater treatment plant in Germany by food waste co-digestion and improved aeration

Population growth, tightening effluent discharge requirements and increasing energy costs are driving the wastewater treatment sector to improve energy efficiency and strive towards energy self-sufficiency. Despite many strategies being proposed for improving energy self-sufficiency at wastewater treatment plants (WWTPs), limited case studies have been conducted. This full-scale case study at Grüneck WWTP evaluates the effectiveness of two different strategies and quantifies their plant-wide impact. Grüneck WWTP increased energy self-sufficiency by 24% (from 64 to 88%) through reducing energy consumption with aeration upgrades (8% increase) and increasing energy production with food waste co-digestion (16% increase). The plant-wide analysis indicated that the aeration upgrades did not affect effluent quality; however co-digesting food waste at 20% additional organic load caused some minor downstream impacts including reduced dewaterability, fluctuating biogas quality and solids accumulation. A solar dryer was installed to manage the increased biosolids production resulting from co-digestion. The dryer reduced biosolids transportation costs by 30% with minimal increase in total plant energy (below 2%). Payback periods for the co-digestion facility and blower upgrade were 10 and 17 months, respectively. The solar dryer, however, has a payback period of 30 years. Findings from this case study provide practical knowledge of the trade-offs for different strategies commonly employed to improve energy self-sufficiency at WWTPs. The results provide evidence that there is significant incentive for similar plants to improve energy self-sufficiency through co-digestion and aeration upgrades.

Occurence and Prioritization of Pharmaceutical Active Compounds in Domestic/Municipal Wastewater Treatment Plants

In this study, pharmaceutically active compounds (PhACs) were analyzed in the influent and effluent of a domestic wastewater treatment plant in Turkey and a municipal wastewater treatment plant in Germany and the toxicity of these wastewaters were estimated using a toxic unit (TU) approach. A total of 21 and 32 PhACs were detected in the domestic wastewater and the municipal wastewater, respectively. The TUs estimated for PhACs in municipal wastewater were higher than the TUs estimated for PhACs present in domestic wastewater. The levels of the anti-anxiety drug, oxazepam were estimated to be in the high risk category (HQ > 10) in both wastewaters. In bench-scale tests with ozonation, the removals of four PhACs in the municipal wastewater were investigated. At a dose of 2mg/L ozone, 97%-98% of diclofenac and carbamazepine were removed. The lowest removal rate at 71% was observed for metoprolol.

Towards an eDNA metabarcode-based performance indicator for full-scale municipal wastewater treatment plants

Knowledge-driven management for wastewater treatment plant (WWTP) performance becomes increasingly important considering the globally growing production of wastewater and the rising demand of clean water supply. Even though the potential of microbial organisms (bacteria and protists) as bioindicators for WWTP performance is well known, it is far from being fully exploited for routine monitoring programs. Therefore, we here used massive sequencing of environmental (e)DNA metabarcodes from bacterial (V3-V4 region of the SSU rRNA gene) and eukaryote (V9 region of the SSU rRNA gene) communities in 21 activated sludge samples obtained from full-scale municipal WWTPs in Germany. Microbial community patterns were compared to standard WWTP operating parameters and two traditionally used WWTP performance indicators (Sludge Biotic Index and Sludge Index). Both indices showed low concordance and hardly correlated with chemical WWTP performance parameters nor did they correlate with microbial community structures. In contrast, microbial community profiles significantly correlated with WWTP performance parameters and operating conditions of the plants under study. Therefore, eDNA metabarcode profiles of whole microbial communities indicate the performance of WWTP and can provide useful information for management strategies. We here suggest a strategy for the development of an eDNA metabarcode based bioindicator system, which can be implemented in future standard monitoring programs for WWTP performance and effluent quality.

Efficient Low-Cost Anaerobic Treatment of Wastewater Using Biochar and Woodchip Filters

Access to improved sanitation is often lacking in many low-income countries, and approximately 90% of the sewage is discharged without treatment into receiving water bodies. The aim of this study was the development and evaluation of an efficient low-cost wastewater treatment system for developing countries. Biochar and woodchips, potential locally available and inexpensive materials, were used for anaerobic wastewater filtration and their suitability evaluated in comparison to gravel as a common reference material. Filters were fed with raw sewage from a municipal full-scale wastewater treatment plant in Germany at 22 °C room temperature with a hydraulic loading rate (HLR) of 0.05 m∙h−1. This resulted in a mean organic loading rate (OLR) of 252 gCOD∙m−3∙d−1 and a mean organic surface load of 456 gCOD∙m−2∙d−1. To determine the influence of different filter materials, the removal efficiency of chemical oxygen demand (COD), total organic carbon (TOC), turbidity, and faecal indicator bacteria (FIB) E. coli and enterococci were tested. It was found that COD (up to 90%), TOC (up to 80%), FIB (up to 1.7 log10-units), and turbidity (effluent turbidity below 35 NTU) could be significantly reduced. The findings of this study demonstrate the potential of anaerobic filters (AFs) for wastewater treatment in low-income countries to reduce water pollution and comprehensively improve water quality. The performance of biochar filters was significantly better over the entire experiment compared to woodchip and gravel filters with respect to COD, TOC, turbidity, and FIB removal, indicating the superior properties of biochar for wastewater treatment.