Volatile Methylsiloxanes Concentrations Research Articles

Concentrations of Volatile Methyl Siloxanes in New York City Reflect Emissions from Personal Care and Industrial Use.

Volatile methyl siloxanes (VMS) are a group of organosilicon compounds of interest because of their potential health effects, their ability to form secondary organic aerosols, and their use as tracer compounds. VMS are emitted in the gas-phase from using consumer and personal care products, including deodorants, lotions, and hair conditioners. Because of this emission route, airborne concentrations are expected to increase with population density, although there are few studies in large urban centers. Here, we report summertime concentrations and daily variations of VMS congeners measured in New York City. Median concentrations of the 6 studied congeners, D3 (20 ng m-3), D4 (57 ng m-3), D5 (230 ng m-3), D6 (11 ng m-3), L5 (2.5 ng m-3), and L7 (1.3 ng m-3) are among the highest reported outdoor concentrations in the literature to date. Average congener ratios of D5:D4 and D5:D6 were consistent with previously reported emissions ratios, suggesting that concentrations were dominated by local emissions. Measured concentrations agree with previously published results from a Community Multiscale Air Quality model and support commonly accepted emissions rates for D4, D5, and D6 of 32.8, 135, and 6.1 mg per capita per day. Concentrations of D4, D5, D6, L5, and L7 and total VMS were significantly lower during the day than during the night, consistent with daytime oxidation reactivity. Concentrations of D3 did not show the same diurnal trend but exhibited a strong directional dependence, suggesting that it may be emitted by industrial point sources in the area rather than personal care product use. Concentrations of all congeners had large temporal variations but showed relatively weak relationships with wind speed, temperature, and mixing height.

Helping WWTP managers to address the volatile methylsiloxanes issue–Behaviour and complete mass balance in a conventional plant

Volatile methylsiloxanes (VMSs) are a group of additives employed in different consumer products that can affect the quality of the biogas produced in wastewater treatment plants (WWTPs). The main objective of this study is to understand the fate of different VMSs along the treatment process of a WWTP located in Aveiro (Portugal). Thus, wastewater, sludge, biogas, and air were sampled in different units for two weeks. Subsequently, these samples were extracted and analyzed by different environment-friendly protocols to obtain their VMS (L3-L5, D3-D6) concentrations and profiles. Finally, considering the different matrix flows at every sampling moment, the mass distribution of VMSs within the plant was estimated. The levels of ∑VMSs were similar to those showed in the literature (0.1–50 μg/L in entry wastewater and 1–100 μg/g dw in primary sludge). However, the entry wastewater profile showed higher variability in D3 concentrations (from non detected to 49 μg/L) than found in previous studies (0.10–1.00 μg/L), likely caused by isolated releases of this compound that could be related to industrial sources. Outdoor air samples showed a prevalence of D5, while indoor air locations were characterized by a predominance of D3 and D4. Differences in sources and the presence of an indoor air filtration system may explain this divergence. Biogas was characterized by ∑VMSs concentrations (8.00 ± 0.22 mg/m3) above the limits recommended by some engine manufacturers and mainly composed of D5 (89%). Overall, 81% of the total incoming mass of VMSs is reduced along the WWTP, being the primary decanter and the secondary treatment responsible for the highest decrease (30.6% and 29.4% of the initial mass, respectively). This reduction, however, is congener dependant. The present study demonstrates the importance of extending sampling periods and matrices (i.e., sludge and air) to improve sample representativity, time-sensitivity, and the accuracy of mass balance exercises.

Spatial distribution and accumulation profiles of volatile methylsiloxanes in Tokyo Bay, Japan: Mass loadings and historical trends

We investigated mass loading and the spatial distribution of volatile methylsiloxanes (VMSs) including four cyclic VMSs (D3–D6; cVMSs, the number refers to the number of SiO bonds) and three linear VMSs (L3–L5; lVMSs) in Tokyo Bay, Japan, which is one of the most industrialized, urbanized, and populated areas in the world. Based on the VMS concentrations determined in eight main inflow rivers to the bay, the mass loading of VMSs via inflow rivers and sewage treatment plants located in Tokyo Bay was estimated at 2500 kg/y for total VMSs. Elevated mass loadings of VMSs were found in three of the rivers, inflowing to the inner west of Tokyo Bay. The distribution and deposition characteristics of VMSs were observed depending on the estuarine condition. Estuarine sediments were found to be efficient and effective traps for VMSs and the salting-out effect is one possible mechanism to explain this phenomenon. The overall profiles of D4, D5, and D6 in surface water and sediment were observed across Tokyo Bay; elevated concentrations were identified in the inner west bay with dispersed low concentrations in the outer bay, except for one hotspot of D4 in the sediment, indicating a major emission route of VMSs via inflow rivers. Additionally, the historical pollution profiles of VMSs in Tokyo Bay were reconstructed based on the VMS concentrations determined in a dated sediment core. VMSs were identified throughout the upper 40 cm of the sediment core (representing the mid 1980s); the profiles correspond with the historical use of VMSs in wash-off personal care-products. The noted decreasing trend of D4 might be a reflection of the early 2000s replacement of D4 with D5 in such products. The elevated VMS concentrations in the estuarine sediment raise concerns about the impact on the aquatic environment.

Spatial variations of linear and cyclic volatile methyl siloxanes in a river basin and their air-water exchange

Linear and cyclic volatile methylsiloxanes (VMS) are Si and O containing organic compounds that are increasingly subject to scientific studies in recent years. They are used as solvents and coating materials in personal care products, cleaning materials and industrial applications. In this study, it was aimed to investigate the spatial variations of VMS levels in river water and ambient air in Kucuk Menderes Basin and their air-water exchange patterns. Grab river water samples and passive ambient air samples collected from 10 sites throughout Kucuk Menderes Basin located in Izmir region in Turkey, and they were analyzed for VMS. The concentrations of ΣVMS in river water and ambient air ranged from 48.4 to 148 ng L−1 and from 41.7 to 433 ng m−3, respectively. Among the VMS compounds, the predominant compounds were found to be D5 and D3 in ambient air and river water, respectively. In general, concentrations of all VMS congeners increased towards downstream of the river for both water and ambient air samples and there were substantial fluctuations between the sampling points. These fluctuations may be due to wastewater discharges at some sites (increase), followed by loss by volatilization along the river (decrease). VMS concentrations measured in air and river water samples were used to estimate the net air-water exchange fluxes. In all cases, fluxes were negative, ranging between −159 (L4) and −11100 (D3) ng m−2 day, indicating volatilization from water is a source for atmospheric VMS.

Investigating the presence and persistence of volatile methylsiloxanes in Arctic sediments.

Volatile methylsiloxanes (VMS) have been identified as contaminants of emerging concern in aquatic systems. Here, we report on the presence of VMS in sediment and wastewater from Arctic regions in 2014 to 2016 and model their persistence in Adventfjorden in Longyearbyen, Svalbard. Total concentrations of VMS in sediment were dominated by D4 and D5 and ranged from 0.0024 to 1.7 ng g-1 at Svalbard (Longyearbyen), from 4.0 to 43 ng g-1 in Greenland (Nuuk) and from 0.19 to 21 ng g-1 in the Canadian Archipelago. Concentrations in wastewater samples from Svalbard ranged from 12 to 156 ng L-1. Large variability in reported values of the partition ratio between organic carbon and water (KOC) and enthalpy of sorption (ΔHOC; often estimated from enthalpy of phase change between octanol and water, ΔHOW) of VMS has resulted in high uncertainty in evaluating persistence in aquatic systems. We evaluated previously reported KOC and ΔHOC values from the literature in predicting measured VMS concentrations in sediment and wastewater in scenarios using a fugacity-based multimedia model for VMS concentrations in Svalbard. We tested two different model scenarios: (1) KOC and ΔHOW measurements for three cyclic VMS previously reported by Kozerski et al. (Environ. Toxicol. Chem., 2014, 33, 1937-1945) and Xu and Kropscott (Environ. Chem., 2014, 33, 2702-2710) and (2) the KOC and ΔHOC measurements from Panagopoulos et al. (Environ. Sci. Technol., 2015, 49, 12161-12168 and Environ. Sci. Technol. Lett., 2017, 4(6), 240-245). Concentrations of VMS in sediment predicted from concentrations in wastewater in scenario 2 were in good agreement with measured concentrations, whereas in scenario 1, predicted concentrations were 2 to 4 orders of magnitude lower. Such large discrepancies indicate that the differences in the predicted concentrations are more likely to be attributed to KOC and ΔHOC than to uncertainty in environmental parameters or emission rates.

A review of contamination status, emission sources, and human exposure to volatile methyl siloxanes (VMSs) in indoor environments.

Siloxanes are organo-silicon compounds containing Si-O-Si linkages and methyl branches. Depending on the structure, siloxanes can be divided into cyclic and linear compounds. Methyl siloxanes with small and medium molecular weights (molecular weights less than 500 g mol-1), are volatile under normal conditions, and hence are referred to as volatile methyl siloxanes (VMSs). VMSs are additive ingredients in many products such as plastics, rubber, personal care products, and household items. This review provides information on the distribution of VMSs in consumer products, indoor air and dust, and their implications for human exposure. VMSs have been used in personal care products and household items at concentrations on the order of hundreds to thousands of micrograms per gram which are the main sources of contamination in the indoor environments. VMSs have been found widely in indoor air and dust. A significant correlation existed between VMS concentrations in indoor air and dust. Among typical VMSs, dodecamethylcylcopentasiloxane (D5) is the major compound found in indoor environments. The human exposure doses to VMSs through dermal absorption, dust ingestion, and inhalation were compiled; Inhalation is a dominant pathway of exposure to VMSs, especially in indoor environments of occupational settings like hair salons. The human exposure doses were higher in children than in adults.

Assessment of volatile methylsiloxanes in environmental matrices and human plasma

Volatile methylsiloxanes (VMSs) are widely used in various personal-care products and industrial additives and products. This study focused on VMSs exposure in the general population, workers, and the families of workers living in residential and industrial areas of southwestern China. VMSs concentrations in indoor environmental matrices from six industrial facilities were 3.4 × 102 to 9.0 × 102 μg m−3 in gas-phase samples, 4.7 × 102 to 1.5 × 104 μg g−1 in PM2.5 samples, and 2.3 × 102 to 7.2 × 103 μg g−1 in dust samples, which were two to four orders of magnitude higher than the concentrations measured in residential areas. Exposure to VMSs was investigated by analysis of plasma samples from workers in residential and industrial areas for the presence of cyclic (D4–D6) and linear (L3–L16) VMSs. VMSs concentrations in plasma samples ranged from 84 to 2.3 × 102 ng ml−1 in workers, one to two orders of magnitude higher than those in the general population (2.2 ng ml−1). Daily VMSs indoor exposure via inhalation and ingestion in individuals from residential and industrial areas were estimated and assessed under working-time and leisure-time conditions. This study showed that exposure to VMSs in industrial areas is approximately two to four or one to two orders of magnitude higher than that in residential areas during the working- or leisure-time scenario, respectively. Furthermore, the families of workers (the non-occupational group) experienced higher levels of exposure to VMSs in their homes compared with the general population. The ratios of exposure to linear VMSs via PM2.5 inhalation to that via the gas phase ranged from 7.8% to 43.1% in industrial areas. This study suggests that intake of linear VMSs via PM2.5 inhalation should be considered when estimating human exposure to VMSs in areas with high levels of PM2.5 air pollution.

Determination of linear and cyclic volatile methyl siloxanes in biogas and biomethane by solid-phase microextraction and gas chromatography-mass spectrometry

A new method based on solid-phase microextraction (SPME) followed by gas chromatography-mass spectrometry (GC-MS) was developed for the analysis of seven linear (L2 – L5) and cyclic (D3 – D5) volatile methyl siloxanes (VMS) in biogas and biomethane, directly collected into Tedlar® bags (Tedlar SPME) from anaerobic digesters and wastewater treatment plants. The method was employed to monitor VMS content in biomethane produced by biogas upgrading with a pilot-plant membrane unit and provided adequate limits of quantification (< 0.05 mg m−3) to detect trace siloxane impurities. Tedlar SPME was validated against a standard procedure based on indirect sampling of gas streams with sorbent tubes followed by solvent extraction and GC-MS. Method precision (RSD) on total and individual VMS concentrations was lower than 10%, while RSD values of the standard procedure were higher than 20%. Tedlar SPME suitably revealed high VMS levels, expressed as total volatile silicon (> 1 mgSim−3), in wastewater biogas and provided a more efficient sampling of heavier VMS in comparison to the sorbent tubes method. At low values (< 0.1 mgSim−3) typical of wood waste biogas and biomethane, no statistically significant differences were observed between the two methods. Overall, Tedlar SPME simplified the analytical procedure by reducing the procedural steps, avoiding the use of solvents and demonstrated its applicability for testing the quality of biomethane as advanced biofuel.

Atmospheric Concentrations of New Persistent Organic Pollutants and Emerging Chemicals of Concern in the Group of Latin America and Caribbean (GRULAC) Region.

A special initiative was run by the Global Atmospheric Passive Sampling (GAPS) Network to provide atmospheric data on a range of emerging chemicals of concern and candidate and new persistent organic pollutants in the Group of Latin America and Caribbean (GRULAC) region. Regional-scale data for a range of flame retardants (FRs) including polybrominated diphenyl ethers (PBDEs), organophosphate esters (OPEs), and a range of alternative FRs (novel FRs) are reported over 2 years of sampling with low detection frequencies of the novel FRs. Atmospheric concentrations of the OPEs were an order of magnitude higher than all other FRs, with similar profiles at all sites. Regional-scale background concentrations of the poly- and perfluoroalkyl substances (PFAS), including the neutral PFAS (n-PFAS) and perfluoroalkyl acids (PFAAs), and the volatile methyl siloxanes (VMS) are also reported. Ethyl perfluorooctane sulfonamide (EtFOSA) was detected at highly elevated concentrations in Brazil and Colombia, in line with the use of the pesticide sulfluramid in this region. Similar concentrations of the perfluoroalkyl sulfonates (PFAS) were detected throughout the GRULAC region regardless of location type, and the VMS concentrations in air increased with the population density of sampling locations. This is the first report of atmospheric concentrations of the PFAAs and VMS from this region.

Volatile Methylsiloxanes and Organophosphate Esters in the Eggs of European Starlings (Sturnus vulgaris) and Congeneric Gull Species from Locations across Canada.

Volatile methylsiloxanes (VMSs) and organophosphate esters (OPEs) are two suites of chemicals that are of environmental concern as organic contaminants, but little is known about the exposure of wildlife to these contaminants, particularly in birds, in terrestrial and aquatic ecosystems. The present study investigates the spatial distributions of nine cyclic and linear VMSs and 17 OPEs in the eggs of European starlings (Sturnus vulgaris) and three congeneric gull species (i.e., herring gull (Larus argentatus), glaucous-winged gull (L. glaucescens), and California gull (L. californicus)) from nesting sites across Canada. ∑VMS concentrations for all bird eggs were dominated by decamethylcyclopentasiloxane (D5), dodecamethylcyclohexasiloxane (D6), and octamethylcyclotetrasiloxane (D4). With European starlings, birds breeding adjacent to landfill sites had eggs containing significantly greater ∑VMS concentrations (median: 178 ng g-1 wet weight (ww)) compared with those from the urban industrial (20 ng g-1 ww) and rural sites (1.3 ng g-1 ww), indicating that the landfills are important sources of VMSs to Canadian terrestrial environments. In gull eggs, the median ∑VMS concentrations were up to 254 ng g-1 ww and suggested greater detection frequencies and levels of VMSs in aquatic- versus terrestrial-feeding birds in Canada. In contrast, the detection frequency of OPEs in all European starling and gull eggs was lower than 16%. This suggested that low dietary exposure or rapid metabolism of accumulated OPEs occurs in aquatic feeding birds and may warrant further investigation for the elucidation of the reasons for these differences.

Volatile methyl siloxanes (VMS) concentrations in outdoor air of several Catalan urban areas

Volatile methyl siloxanes (VMS) were evaluated in ten Catalan urban areas with different industrial impacts, such as petrochemical industry, electrical and mechanical equipment, metallurgical and chemical industries, municipal solid waste treatment plant and cement and food industries, during 2013–2015. 24 h samples were taken with LCMA-UPC pump samplers specially designed in our laboratory, with a flow range of 70 ml min−1. A sorbent-based sampling method, successfully developed to collect a wide-range of VOC, was used. The analysis was performed by automatic thermal desorption coupled with capillary gas chromatography/mass spectrometry detector. The presented methodology allows the evaluation of VMS together with a wide range of other VOC, increasing the number of compounds that can be determined in outdoor air quality assessment of urban areas. This aspect is especially relevant as a restriction of several VMS (D4 and D5) in consumer products has been made by the European Chemicals Agency and US EPA is evaluating to include D4 in the Toxic Substances Control Act, regarding the concern of the possible effects of these compounds in human health and the environment. ΣVMS concentrations (L2-L5, D3-D6 and trimethylsilanol) varied between 0.3 ± 0.2 μg m−3 and 18 ± 12 μg m−3, determined in a hotspot area. Observed VMS concentrations were generally of the same order of magnitude than the previously determined in Barcelona, Chicago and Zurich urban areas, but higher than the published from suburban sites and Arctic locations. Cyclic siloxanes concentrations were up to two-three orders of magnitude higher than those of linear siloxanes, accounting for average contributions to the total concentrations of 97 ± 6% for all samples except for the hotspot area, where cyclic VMS accounted for 99.9 ± 0.1%. D5 was the most abundant siloxane in 5 sampling points; however, differing from the generally observed in previous studies, D3 was the most abundant compound in the other 5 sampling points.

Modeling and monitoring cyclic and linear volatile methylsiloxanes in a wastewater treatment plant using constant water level sequencing batch reactors

The fate of cyclic and linear volatile methylsiloxanes (VMSs) was evaluated in a wastewater treatment plant (WWTP) using constant water level sequencing batch reactors from Dalian, China. Influent, effluent, and sewage sludge samples were collected for seven consecutive days. The mean concentrations of cyclic VMSs (cVMSs) in influent and effluent samples are 1.05μgL−1 and 0.343μgL−1; the total removal efficiency of VMSs is >60%. Linear VMS (lVMS) concentration is under the quantification limitation in aquatic samples but is found in sludge samples with a value of 90μgkg−1. High solid-water partition coefficients result in high VMS concentrations in sludge with the mean value of 5030μgkg−1. No significant differences of the daily mass flows are found when comparing the concentration during the weekend and during working days. The estimated mass load of total cVMSs is 194mgd−11000inhabitants−1 derived for the population. A mass balance model of the WWTP was developed and derived to simulate the fate of cVMSs. The removal by sorption on sludge increases, and the volatilization decreases with increasing hydrophobicity and decreasing volatility for cVMSs. Sensitivity analysis shows that the total suspended solid concentration in the effluent, mixed liquor suspended solid concentration, the sewage sludge flow rate, and the influent flow rate are the most influential parameters on the mass distribution of cVMSs in this WWTP.

Calibration and Application of a Passive Air Sampler (XAD-PAS) for Volatile Methyl Siloxanes

Because the atmosphere is key to understanding the environmental behavior of volatile methyl siloxanes (VMS), a variety of reliable air sampling methods are needed. The purpose of this study was to calibrate and evaluate an existing, polystyrene-divinylbenzene copolymeric resin-based passive air sampler (XAD-PAS) for VMS. Sixteen XAD-PAS were deployed for 7-98 days at a suburban site in Toronto, Canada, while the VMS concentration in air was monitored by an active sampling method. This calibration and a subsequent field test further allowed for investigation of the temporal and spatial variability of VMS in the region. Uptake in the XAD-PAS of octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and three linear VMS was linear throughout the whole deployment period. Sampling rates were between 0.4 and 0.5 m(3)/day. The XAD-PAS measured ∑VMS concentrations ranged from nondetects in rural areas (n = 3), to 169 ± 49 ng/m(3) in the urban region (n = 21), to levels above 600 ng/m(3) at sewage treatment plants (n = 2). Levels and composition of VMS within the urban area were remarkably uniform in space. Levels, but not composition, were highly variable in time and weakly correlated with temperature, wind speed, and wind direction.