Visible LED Research Articles

Optoelectronic Oscillator Using Visible LEDs and Plastic Optical Fibers

Optoelectronic Oscillator Using Visible LEDs and Plastic Optical Fibers

Performance Evaluation of the Two-Input Buck Converter as a Visible Light Communication High-Brightness LED Driver Based on Split Power.

This work proposes a high-efficiency High-Brightness LED (HB-LED) driver for Visible Light Communication (VLC) based on a Two-Input Buck (TIBuck) DC/DC converter. This solution not only outperforms previous approaches based on Buck DC/DC converters, but also simplifies previous proposals for VLC drivers that use the split power technique with two DC/DC converters: one is in charge of the communication tasks and the other controls the biasing of the HB-LED (i.e., lighting tasks). The real implementation of this scheme requires either two input voltage sources, one of which is isolated, or one DC/DC converter with galvanic isolation. The proposed implementation of splitting the power is based on a TIBuck DC/DC converter that avoids the isolation requirement, overcoming the major drawback of this technique, keeping high-efficiency and high communication capability thanks to the lower voltage stress both across the switches and at the switching node. This fact allows for the operation at very high frequency for communication purposes, minimizing switching power losses, achieving high efficiency and providing lower filtering effort. Moreover, the duty ratio range can also be adapted to the useful voltage range of the HB-LED load to maximize the resolution on the tracking of the output volage. The power is split by means of an auxiliary Buck DC/DC converter operating at low switching frequency, which generates the secondary voltage source needed by the TIBuck DC/DC converter. This defines a natural split of power by only processing the power delivered for communications purposes at high frequency. A 7 W output-power experimental prototype of the proposed VLC driver was built and tested. Based on the experimental results, the prototype achieved 94% efficiency, reproducing a 64-QAM digital modulation scheme and achieving a bit rate of 1.5 Mbps with error in communication of 12%.

Constructing AlOOH-PVA/ZIF-67/AgCl/Ag composite membrane for the efficient photodegradation of organic pollutants under visible light irradiation

This study effectively fabricated photocatalytic membranes (∼5 cm diameter) assembled by γ-AlOOH-PVA (BOP) decorated heterostructural ZIF-67/AgCl/Ag composites by combing seeded secondary growth and photoreduction methods. First, the ZIF-67-seeded BOP membrane was shaped in a petri dish, followed by submerging in a 2-methylimidazole ligand for secondary growth to obtain the BOP/ZIF-67 membrane. Next, AgCl/Ag was formulated on the membrane by dipping it in an AgNO3 solution, followed by a photoreduction under visible LED light, resulting in a BOP/ZIF/AgCl/Ag membrane. The characterization showed that the membrane contained heterostructures of ZIF-67/AgCl/Ag anchored onto the BOP membrane. The BOP/ZIF/AgCl/Ag composite membranes exhibited enhanced light absorption and appeared the localized surface plasmon resonance (LSPR) of Ag0, giving it a bandgap energy of ∼2.10 eV. Photodegradation under visible LED light irradiation showed that the BOP/ZIF/AgCl/Ag membrane efficiently removed tetracycline (TC) and Rhodamine B dye (RhB) with corresponding degradation efficiency of ∼99% (90 min) and ∼95% (140 min), giving reaction rates of ∼0.046 min−1 and 0.019 min−1, respectively. The photocatalytic mechanism and photodegradation pathways analyses provided insights into the degradations of organic pollutants. Significantly, the designed BOP/ZIF/AgCl/Ag membrane quickly recovered from the solution and was of good durability. The study provided an effective strategy for constructing heterostructural ZIF-67/AgCl/Ag composite membranes, which are efficient and eco-friendly photocatalyst materials.

Self-sacrificing template fabrication of mesoporous CuO micro/nanoplates for photo-Fenton-like oxidation of sulfathiazole

In this study, we offer a simple self-sacrificial template-directed method to prepare mesoporous CuO micro/nanoplates by using copper hydroxide acetate (Cu2(OH)3(CH3COO)·H2O) plates as a template. The as-prepared material was structurally, morphologically, optically and texturally characterized and its excellent catalytic activity in the LED-driven photo-Fenton-like process of sulfathiazole oxidation was demonstrated. Within 90 min, 100 % sulfathiazole degradation and 87.3 % TOC removal were achieved in the presence of H2O2 and visible LED irradiation. Moreover, the degradation of sulfathiazole can still reach 96.1 % after five cycles, which indicates exceptional performance of the catalyst.

Highly efficient adsorption and visible-LEDs-driven photodegradation of tetracycline over novel and green-synthesized p-BiOI/n-Bi2WO6 heterojunctions

Preparing bismuth compounds-based heterojunctions with superior redox capability has emerged as a promising strategy for environmental remediation. Herein, p-BiOI/n-Bi2WO6 heterojunctions were successfully obtained via a novel, facile, and green solvothermal method. The heterojunctions were synthesized using different mass ratios (1:2, 1:1, and 2:1) of BiOI (BI) and Bi2WO6 (BW), with 1:1 as the best ratio, which was decorated with silver nanoparticles (Ag-NPs) and nitrogen-doped graphene (NG) applying green methodologies. The as-prepared BI/BW heterojunctions were characterized by several techniques, and their adsorption capacity and photodegradation activity toward tetracycline (TC) under 19 W visible LEDs illumination were investigated. The capacity of pure BI, BW and BI/BW heterojunctions for adsorbing TC ranged from 14 to 68 mg/g; among the heterojunctions, Ag/1BI/1BW showed the highest TC adsorption capacity, 35 mg/g. Moreover, the photocatalytic tests revealed that the Ag/1BI/1BW exhibited the highest catalytic performance, achieving a TC percentage degradation of 81 % within 120 min. The low nominal power consumption of the LED-based photoreactor (0.0475 kWh) was significantly lower than that reported in the literature for using Xe or Hg lamps. In addition, catalyst dosage, initial TC concentration, and solution pH were investigated, demonstrating that they play important role in TC photodegradation. Scavenger assays determined that the degradation of TC using Ag/1BI/1BW proceeds mainly via superoxide radicals and holes, which agrees with the carrier transfer mechanism postulated for this heterojunction. TOC analysis revealed that the efficiency of Ag/1BI/1BW was 63 %, and reuse tests confirmed its high performance even after three cycles. This research provides new insights into the design of high-performance heterojunctions for water treatment.

Sintering Driven Void Formation in PS@WO3 Core-Shell Composites: A Photodegradation Enhancement Strategy

Background: Polystyrene nanospheres are used as a substrate for the hydrothermal coating of tungsten trioxide (WO3) to form a core-shell composite of PS@WO3. The core-shell structure is used for the next sintering step. This produces porous WO3. The focus of this study is on the role of porous WO3 in enhancing photocatalytic performance. Methods: The hydrothermal method was employed for coating, and the surface morphology, as well as the structural properties of WO3-coated PS spheres, were systematically investigated using SEM and XRD analyses. Additionally, the sintering process was introduced to enhance the material by inducing rupture in the PS sphere core, creating voids that significantly increased the material's surface area. Results: The evaluation of the effect of sintering temperature on photodegradation efficiency highlighted the crucial role of sintering temperature. Un-sintered and 300°C sintered WO3, both having a hexagonal crystalline structure, exhibited superior degradation efficiencies compared to samples sintered at higher temperatures (400°C and 500°C). In particular, the 300°C sintered WO3 outperformed its un-sintered counterpart despite identical crystalline structures. The performance of the PS@WO3 composite was assessed to determine the enhanced role of porous WO3. The porous WO3 obtained, in particular by the sintering of the core-shell PS@WO3 composites at 300°C, showed a remarkable improvement in the degradation efficiency. These composite demonstrated over 95% efficiency within 10 minutes and achieved near complete (100%) degradation for a further 10 minutes, surpassing the performance of pure WO3. It is important to clarify that while the final product was predominantly WO3 after the sintering process, the inclusion of PS served a critical purpose in creating voids during sintering. The PS@WO3 composite structure used as a resource for the preparation of porous WO3, even with a potentially reduced PS composition, has been found to play a significant role in influencing the surface area of the material, and consequently the photocatalytic performance. Conclusion: The study has highlighted the importance of crystalline structure and sintering conditions in optimizing the efficiency of photocatalytic materials. The porous WO3 obtained, in particular by the sintering of the core-shell PS@WO3 composites at 300°C, showed promising potential for applications under UV and visible LED light irradiation. These results provide valuable insights for the development of advanced photocatalytic materials with improved performance, highlighting WO3 as the key contributor to the observed improvements.

ZnO-modified glass capillaries as a portable photocatalytic reactor for real-time measurements

Abstract Here, we have developed a photocatalytic reactor using glass capillaries which acts both as a flow cell and a thin film-supported photocatalyst due to the Zinc Oxide (ZnO) nanostructures grown on the inner surface of the glass capillaries. The structural, morphological, elemental, and optical characteristics of the ZnO nanostructures were investigated through characterization methods such as x-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Energy-Dispersive x-ray spectroscopy (EDAX), UV–Visible spectroscopy, and Raman spectroscopy. Further, dye-sensitized ZnO nanostructures were used for photocatalytic application under visible light irradiation. A custom-made setup is developed using ZnO-modified glass capillaries for simultaneous decay and measurement of the dye degradation process under visible LED light. This developed model could have future technological applications in designing portable photocatalytic reactors that can accurately monitor the dye degradation process using real-time measurements.

Fe(III)-incorporated UiO-66(Zr)–NH2 frameworks: Microwave-assisted scalable production and their enhanced photo-Fenton degradation catalytic activities

In this work, the photocatalytic feasibility of UiO-66(Zr)–NH2 was tuned by combining a scalable producing approach and incorporating Fe3+. Different contents of Fe3+ were effectively incorporated into the UiO-66(Zr)–NH2 frameworks utilizing a microwave-assisted continuous flow tubular reactor within 10 min. It was observed that with increasing the Fe3+ content from 0.5 to 1.0, 2.0 and 3.0 M %, the production rate diminished from ∼ 1.72 to 1.65, 1.55, and 1.46 g/h, respectively. The hybrid Fe@UiO-66-NH2 (Fe@UON) showed enhanced light absorption and charge carrier separation efficiency owing to the newly formed heterostructures, Zr-O-Fe linkages, and –H2N:→ Fe3+ chelating. The optimal Fe@UON catalyst achieved the highest photo-Fenton degradation efficiency of ∼ 96 % towards tetracycline (TC) under energy-saving visible LED light (VLEL) conditions. The photodegradation was predominantly governed by the photo-induced species of ·O2–, h+, and •OH and facilitated by the Fe3+/Fe2+ cycles. At the same time, LC/MS analyses detailedly revealed the reaction pathways for the degradation. After several consecutive tests, the constructed hybrid Fe@UiO-66-NH2 catalysts maintained good catalytic durability, and there was an insignificant Fe leak to the environment. The findings showed that hybrid Fe3+@UiO-66(Zr)–NH2 derived from energy-effective, environmental and scalable methods could be a good material for treating antibiotic-polluted effluents.

Enhanced photocatalytic activity of titanium-doped copper ferrite for methyl green dye degradation under commercial visible LED light

This study examines the effect of TiO₂ doping on the catalytic performance of copper ferrite (CuFe₂O₄) nanoparticles in degrading methyl green dye under visible light. Copper ferrite nanoparticles were synthesized and doped with varying TiO₂ concentrations. The catalysts were characterized using XRD, SEM, EDX, and BET surface area analysis. The TiO₂-doped copper ferrite catalysts showed significantly enhanced catalytic activity compared to undoped copper ferrite. The optimal doping concentration of 10 wt% TiO₂ achieved a degradation efficiency of 92 % for methyl green dye after 60 min of irradiation. The BET surface area increased with TiO₂ doping, contributing to the improved catalytic performance. Reusability tests over five cycles indicated a slight decrease in efficiency, attributed to the loss of active sites. These results indicate that TiO₂ doping effectively enhances the catalytic properties of copper ferrite, making it a viable option for environmental remediation.

BiVO4/sulfur-doped g-C3N4 nanocomposite as photocatalyst for degradation of ciprofloxacin under visible light irradiation

In recent years, the use of antibiotics has greatly increased, which has caused environmental pollution. We offer a photocatalyst based on BiVO4/sulfur-doped g-C3N4 nanocomposite, which was made by a one-step thermal condensation method from thiourea and bismuth vanadate to degradate ciprofloxacin (CIP). The BiVO4/sulfur-doped g-C3N4 photocatalyst was analyzed by certain techniques including XRD, FTIR, BET, FESEM, EDX, TEM, DRS, photoluminesence, and Mott-Schottky to determine various physicochemical properties. The photocatalytic degradation of CIP, as a model pollutant, under visible LED light irradiation was tested to investigate the catalytic performance of nanocomposite. Response Surface Methodology (RSM) was employed to optimize operational parameters, including photocatalyst dosage (50–150 mg), CIP concentration (10–30 mg/L), initial pH of the solution (3–11), and irradiation time (12–120 min). The BiVO4/sulfur-doped g-C3N4 nanocomposite, with a narrow bandgap of 2.15 eV, exhibited exceptional photocatalytic performance in degrading CIP. The optimal conditions for CIP removal were photocatalyst dosage of 120.9 mg, CIP concentration of 10 mg/L, and initial solution pH of 3, resulting in 93.5 % removal efficiency after 105 min of irradiation. The photocatalytic degradation kinetics of CIP followed a pseudo-first-order model with a rate constant (K) of −0.0221 L/min, indicating rapid degradation process. The photocatalyst maintained excellent performance after 5 reuses, with only a 3 % reduction in efficiency. XRD analysis confirmed the structural stability of the nanocomposite after reuse.

Multiphoton-Driven Photocatalytic Defluorination of Persistent Perfluoroalkyl Substances and Polymers by Visible Light.

Perfluoroalkyl substances (PFASs) and fluorinated polymers (FPs) have been extensively utilized in various industries, whereas their extremely high stability poses environmental persistence and difficulty in waste treatment. Current decomposition approaches of PFASs and FPs typically require harsh conditions such as heating over 400 °C. Thus, there is a pressing need to develop a new technique capable of decomposing them under mild conditions. Here, we demonstrated that perfluorooctanesulfonate (PFOS), known as a "persistent chemical," and Nafion, a widely utilized sulfonated FP for ion-exchange membranes, can be efficiently decomposed into fluorine ions under ambient conditions via the irradiation of visible LED light onto semiconductor nanocrystals (NCs). PFOS was completely defluorinated within 8-h irradiation of 405-nm LED light, and the turnover number of the C-F bond dissociation per NC was 17200. Furthermore, 81 % defluorination of Nafion was achieved for 24-h light irradiation, demonstrating the efficient photocatalytic properties under visible light. We revealed that this decomposition is driven by cooperative mechanisms involving light-induced ligand displacements and Auger-induced electron injections via hydrated electrons and higher excited states. This study not only demonstrates the feasibility of efficiently breaking down various PFASs and FPs under mild conditions but also paves the way for advancing toward a sustainable fluorine-recycling society.

Multiphoton‐Driven Photocatalytic Defluorination of Persistent Perfluoroalkyl Substances and Polymers by Visible Light

AbstractPerfluoroalkyl substances (PFASs) and fluorinated polymers (FPs) have been extensively utilized in various industries, whereas their extremely high stability poses environmental persistence and difficulty in waste treatment. Current decomposition approaches of PFASs and FPs typically require harsh conditions such as heating over 400 °C. Thus, there is a pressing need to develop a new technique capable of decomposing them under mild conditions. Here, we demonstrated that perfluorooctanesulfonate (PFOS), known as a “persistent chemical,” and Nafion, a widely utilized sulfonated FP for ion‐exchange membranes, can be efficiently decomposed into fluorine ions under ambient conditions via the irradiation of visible LED light onto semiconductor nanocrystals (NCs). PFOS was completely defluorinated within 8‐h irradiation of 405‐nm LED light, and the turnover number of the C−F bond dissociation per NC was 17200. Furthermore, 81 % defluorination of Nafion was achieved for 24‐h light irradiation, demonstrating the efficient photocatalytic properties under visible light. We revealed that this decomposition is driven by cooperative mechanisms involving light‐induced ligand displacements and Auger‐induced electron injections via hydrated electrons and higher excited states. This study not only demonstrates the feasibility of efficiently breaking down various PFASs and FPs under mild conditions but also paves the way for advancing toward a sustainable fluorine‐recycling society.

Macrocyclic porphyrin photocatalysts without metal chelation: A novel pathway for complete degradation of tough halophenols with longwave visible LED light source

Halophenols are toxic and persistent pollutants in water environments which poses harm to various organisms. Due to their high stability and long residence time, ultraviolet radiation, heavy metals and oxidizing agents have been largely adopted on treating these compounds. However, these treatment methods could pose toxicity or hazardous risks to the marine environment and plant operators. In this study, a water-soluble porphyrin photocatalyst was synthesized and introduced for halophenol treatment using UV-free LED white light. The porphyrin catalyst is a macrocyclic ring consisting of pyrroles linked with methine bridges, the highly conjugated ring provided the superior functionality of visible light absorption. Surprisingly, over 99 % degradation of halophenols and over 90 % dehalogenation have been achieved without metal chelation, even higher than those of transition metal porphyrins with inclusion of Fe3+, Zn2+, Cu2+, Co2+, Ni2+, and Mn2+. Ring-opening reactions were confirmed with the formation of carboxylic acids; dicarboxylic acids like acrylic acid, and malonic acid; while fumaric acid was the main product. Total organic carbon results indicated no CO2 produced during the reaction. Triplet absorbance and scavenger studies also indicated that singlet oxygen and conduction band electrons are the main radical species for halophenol degradation. The 100-fold singlet emission quenching over triplet absorption quenching indicated that the excited electrons tend to be transferred via singlet state. This concept brings along new approaches detoxifying halophenol-related wastewater without UV, metals and other additives, which is more environmentally-friendly and sheds light to the conversion of toxic materials into useful chemical precursors.

Photocatalytic Polyaromatic hydrocarbons (PAH) utilizing magnetic CrFe2O4 nanoparticle: Green synthesis, characterization, ab initio studies, electronic, magnetic features and water treatment application

Polyaromatic hydrocarbons (PAHs) are priority pollutants due to their mutagenicity, persistence, and proven carcinogenicity. Consequently, we investigated the photooxidative degradation of prototypical toxic PAHs, namely anthracene (ANTH) and phenanthrene (PHEN), and naphthalene (NAPH) utilizing magnetic CrFe2O4 nanoparticles under visible light LED irradiation. The prepared nanoparticles, characterized by P-XRD, IR, and SEM, reveal a cubic (FCC) structure and an average particle size of 25.6 nm. On Ab initio study we employed spin polarized first-principle calculations using the Full-Potential Linearized Augmented Plane-Wave (FLAPW) method with GGA-mBJ potentials implemented in the Wien2k package to investigate the properties of CrFe2O4 spinel compound; the calculations reveal that CrFe2O4 adopts a cubic crystal structure with space group 227 (Fd-3 m), and exhibits semiconductor characteristics in both spin channels, featuring indirect band gaps of 1.12 eV (spin-up) and 0.43 eV (spin-down) at the Γ-L and K-Γ points, respectively. Furthermore, the material demonstrates ferromagnetic behavior, with a spin magnetic moment of 20 µB per unit cell. Optical spectra analysis concurs with band structure calculations, suggesting the suitability of this material for photovoltaic applications. The CrFe2O4 magnetic nanoparticles were synthesized through an eco-friendly approach using Boswellia carteri resin as a natural surfactant in an aqueous medium. Our synthesized materials exhibited excellent photocatalytic performance, leading to a rapid exponential decay of ANTH and PHEN over 3 h under visible LED light. The effect of different radical scavengers revealed the role of the percentage of active species OH, h+, and ˙O2− in the oxidation of selected PAHs. At neutral pH, the photo-degradation of PAHs (200 g L−1) by CrFe2O4 (10 mg) followed first-order kinetics and the Langmuir model (R2: 0.99). Exceptional degradation efficiencies were achieved, with ANTH exhibiting a removal efficiency of 99 %, PHEN of 90 %, and NAPH of 86 %. These results show the effectiveness of the synthesized materials as benign and environmentally friendly magnetic nanoparticles for removing carcinogenic PAHs, offering a sustainable, green, and reusable (n = 7) catalytic system to address this environmental challenge.

The Use of Visible LEDs as Technology to Delay Postharvest Senescence of Vegetables: A Review

The Use of Visible LEDs as Technology to Delay Postharvest Senescence of Vegetables: A Review

Dendritic porphyrins as promising sensitizers in aqueous media. From synthesis to potential applications

A homologous series of first generation dendritic phorpyrins (Pf-Ds) were recently synthesized and characterized by conventional methodologies. The main goal of this work was to achieve a practical way of solubilizing this class of efficient sensitizers in high water content aqueous-alcoholic media, by functionalization of a free-base tetraphenyl-porphyrin with polyamido-amine dendritic branches. A high solubility of the Pf-Ds was obtained in such media, whereas the non-functionalized porphyrin was insoluble. Moreover, the photophysical properties of the compounds were evaluated in aqueous solvent by several steady-state and time resolved spectroscopic techniques. The comparison between these data and those in a typical solvent demonstrated that the porphyrin does not show aggregation, retaining its sensitizing capability completely unaltered. Finally, preliminary tests were performed in order to evaluate the ability of Pf-Ds to sensitize the photodegradation of some probe molecules. Effective degradation of the probes was observed after less than 30 min of irradiation with visible LEDs, which is promising for the future application of these compounds as efficient pollutant removers.

Unraveling the antimicrobial activity of CuS functionalized titanates under visible LED light irradiation

Titanate nanotubes (TNs) functionalized with CuS nanoparticles using the microwave-assisted hydrothermal method were characterized via XRD, Raman spectroscopy, UV–Vis spectrophotometry, and N2 physisorption. The as-synthesized CuS/TNs had anatase as the main crystalline phase and the band-gap energy was in the visible region, 2.9 eV. The TNs were recrystallized on titania and functionalized with CuS, forming spherical bundles. SEM showed agglomerates of cauliflower-like semispherical particles. The antimicrobial photoactive assets were evaluated against the bacteria Staphylococcus aureus and Escherichia coli. Inhibition was clearly visible in S. aureus after the first 20 min of exposure to a 6-W LED irradiation lamp. The visible-light catalyzed completely and irreversibly the inactivation of S. aureus after 60 min, however, in the case of E. coli, this material only slightly disturbed its growth, which was recovered after 60 min. The successful result obtained with S. aureus can be explained by the fact that it lacks periplasmic superoxide dismutase (SOD) but has staphyloxanthin for external protection against ROS. However, the CuS/TN particles could release Cu2+ ions, which got attached to bacterium structures or entered the cytoplasm; these events together with the generation of ROS under visible LED light helped inactivate quickly staphyloxanthin, thus inflicting permanent damage to the periplasmic membrane.

Enhancing performance of SnS2 based self-powered photodetector and photocatalyst by Na incorporation

Sn and S are environmentally friendly elements that are abundant in nature. The SnS2 compound formed with these elements has intrinsic n-type electrical conductivity and a direct forbidden band gap of ∼2.2 eV. Therefore, it is a very promising compound for visible light optoelectronic applications. In this study, SnS2thin films were coated on p-Si substrates and pn heterojunction structures were obtained. By adding certain amounts of Na element to SnS2, the photosensitivity of the heterojunction devices increased tremendously and reached a high value of 3.2 × 104 under zero bias condition. It was observed that the prepared devices had excellent speeds and stability with rise and decay times of as low as 28 m s and 23 m s. Moreover, the devices were found to be sensitive to visible light even at ultra-low light intensity of ∼0.3 μW/cm2. Furthermore, the responsivity and specific detectivity values of the prepared photodetectors reach very high values of 11 A/W and 8.4 × 1013 Jones at this low light intensity. The NEP value drops to a low level of 2.7 × 10−15 WHz −1/2. In addition, the photocatalytic properties of Na-doped and undoped SnS2 compound were also examined under visible LED light. Compared to undoped samples, photocatalytic efficiency increased by ∼42 % in Na-doped SnS2 thin films. The findings clearly reveal that Na improves both photodetector device performance and the photocatalytic effect of the SnS2 semiconductor.

Indoor Visible Light Positioning for a Single Partially Visible LED

Indoor Visible Light Positioning for a Single Partially Visible LED

Chromium-doped zinc gallate: Impact of Sn4+ co-doping on the persistent luminescence properties at the nanoscale applied to bio-imaging

Persistent luminescence (PersL) nanoparticles emit a signal that lasts long after the excitation has ended, enabling highly sensitive bioimaging without background noise. By using UV light as the excitation source prior to injection, a strong PersL signal can be detected in vivo before disappearing within a few hours. For long-term imaging, we have shown in the past that visible LED can be used to re-excite ZnGa1.995Cr0.005O4 (ZGO:Cr3+) nanoparticles in vivo, producing a signal intensity that is, however, much lower compared to the signal obtained after the UV pre-excitation method. This lower signal intensity of the nanoprobe when using a visible LED may prevent its detection in some cases. Herein, we report an improvement in visible LED excitation efficiency using PersL Zn1.33Ga1.335Cr0.005Sn0.33O4 (ZGSO:Cr3+) nanoparticles. We fully compared ZGSO:Cr3+ and the original ZGO:Cr nanoparticles in terms of structure, optical properties and bio-imaging potential. Co-doping with tin strongly increases persistent luminescence, even at the nanoscale. In vivo imaging results showed that ZGSO:Cr3+ exhibited an approximately 3-fold signal enhancement over ZGO:Cr3+ using UV pre-excitation. More interestingly, when using LED excitation, the signal intensity of ZGSO: Cr3+ is more than 10 times higher than that of ZGO:Cr3+, making ZGSO nanoparticles much easier to detect. ZGSO:Cr nanoparticles can be surface-modified with PEG to produce nanoprobes with much longer residence time in blood. This unique comparison between the two compositions makes ZGSO:Cr3+ a more effective imaging diagnostic probe than the original ZGO:Cr3+ nanoparticles, opening up new applications for in vivo diagnostics.