Vibrational Sum Frequency Generation Spectra Research Articles

Noncollinear Optical Parametric Amplification of Broadband Infrared Sum Frequency Generation Vibrational Spectroscopy.

Sum-frequency generation (SFG) vibrational spectroscopy is an invaluable tool in surface science, known for its specificity to surfaces and interfaces. Despite its wide application, it is often hampered by weak signal detection. Here, we present an innovative enhancement technique of postsample amplification, using a picosecond noncollinear optical parametric amplifier (NOPA). We conducted a systematical investigation into the impact of different intensities of pump and SFG seed light, as the input signal in NOPA, and demonstrated this method on the octadecanethiol (ODT) molecules on gold films. The amplified SFG by NOPA reproduced the SFG vibrational spectra, enhanced by about 4 orders of magnitude but with broader spectral resolution due to the short pulse width of the pump light in NOPA. This study makes it possible to realize highly sensitive SFG measurements, marking a significant advancement in spectroscopic analysis techniques.

Multimodal Nonlinear Hyperspectral Chemical Imaging Using Line-Scanning Vibrational Sum-Frequency Generation Microscopy.

Vibrational sum-frequency generation (VSFG), a second-order nonlinear optical signal, has traditionally been used to study molecules at interfaces as a spectroscopy technique with a spatial resolution of ~100 µm. However, the spectroscopy is not sensitive to the heterogeneity of a sample. To study mesoscopically heterogeneous samples, we, along with others, pushed the resolution limit of VSFG spectroscopy down to ~1 µm level and constructed the VSFG microscope. This imaging technique not only can resolve sample morphologies through imaging, but also record a broadband VSFG spectrum at every pixel of the images. Being a second-order nonlinear optical technique, its selection rule enables the visualization of non-centrosymmetric or chiral self-assembled structures commonly found in biology, materials science, and bioengineering, among others. In this article, the audience will be guided through an inverted transmission design that allows for imaging unfixed samples. This work also showcases that VSFG microscopy can resolve chemical-specific geometric information of individual self-assembled sheets by combining it with a neural network function solver. Lastly, the images obtained under brightfield, SHG, and VSFG configurations of various samples briefly discuss the unique information revealed by VSFG imaging.

Dimethylpiperazine on Air-Water Interface: Vibrational Sum frequency Generation study of a cyclic tertiary amine

Dimethyl piperazine (DMP) is a weakly basic, cyclic, tertiary diamine. Being a saturated 6-membered ring, it may attain a number of energetically close conformational orientations in the ground state. In a particular environment, its conformational distribution depends on the stabilising factors present in the surroundings. Though soluble in water, it is expected to have substantial surface propensity due to presence of multiple –CH2 and –CH3 bonds. Detection of Bohlmann bands in the C–H stretch region of the Vibrational Sum Frequency Generation (VSFG) spectrum revealed that comparatively higher energy chair conformer with one axial and one equatorial –CH3 bond is present on the pure liquid DMP-air interface. At the air-aqueous solution interface, those bands were found to disappear as the lone electron pair on N-atom is engaged in hydrogen bonding with water molecule. Due to this hydrogen bonding, the peak of “dangling free OH” bonds disappeared from VSFG spectrum of water molecules at air–water interface. Alongwith this hydrogen bonding, the hydrophobic nature of the –CH3 bonds of DMP molecules cause disorganisation of native hydrogen bonded network of water molecules in the air–water interface. Structure and orientation of DMP is expected to be pH-responsive since the chemical conditions of the surrounding medium directly affect the extent of protonation of the amine group. Upon addition of HCl to the bulk, protonated DMP ions, too, could be detected on the air-solution interface by their VSFG spectrum which were considerably different from unprotonated DMP. As the bulk pH of solution changed towards more acidic, spectral features of VSFG spectra of DMP on the surface showed significant change, implying variation in the surface pH, as structure and orientation changes at different degrees of protonation. Since the VSFG spectral features of DMP was found to be pH-responsive, it can be utilised to ascertain the pH of any surface that has DMP absorbed on it. pH-sensitivity of the DMP molecules on air–water interface also suggest that orientation of headgroups will have some effect on the surface orientation of cationic surfactants with amine based headgroups.

Fully First-Principles Surface Spectroscopy with Machine Learning.

Our current understanding of the structure and dynamics of aqueous interfaces at the molecular level has grown substantially due to the continuous development of surface-specific spectroscopies, such as vibrational sum-frequency generation (VSFG). As in other vibrational spectroscopies, we must turn to atomistic simulations to extract all of the information encoded in the VSFG spectra. The high computational cost associated with existing methods means that they have limitations in representing systems with complex electronic structure or in achieving statistical convergence. In this work, we combine high-dimensional neural network interatomic potentials and symmetry-adapted Gaussian process regression to overcome these constraints. We show that it is possible to model VSFG signals with fully ab initio accuracy using machine learning and illustrate the versatility of our approach on the water/air interface. Our strategy allows us to identify the main sources of theoretical inaccuracy and establish a clear pathway toward the modeling of surface-sensitive spectroscopy of complex interfaces.

Computational Investigations of the Water Structure at the α-Al2O3(0001)-Water Interface.

The α-Al2O3(0001)-water interface is investigated using ab initio molecular dynamics (AIMD) simulations. The spectral signatures of the vibrational sum frequency generation (vSFG) spectra of OH stretching mode for water molecules at the interface are related to the interfacial water orientation, hydrogen bond network, and water dissociation process at different water/alumina interfaces. Significant differences are found between alumina surfaces at different hydroxylation levels, namely, Al-terminated and O-terminated α-Al2O3(0001). By calculating the vibrational sum frequency generation spectrum and its imaginary component from AIMD results, the structure of interfacial waters as well as the termination of alumina slab are related to the spectral signatures of vSFG data.

Studying Molecular Rearrangement of P1 Dye at a Passivating Alumina Surface Using Vibrational Sum-Frequency Generation Spectroscopy: Effect of Atomic-Level Roughness.

The effect of roughness and thickness of alumina layers, mimicking the passivation layer commonly used in dye-sensitized photoelectrodes, on the molecular adsorption of P1 dye, 4-(bi(4-(2,2-dicyano-vinyl)-thiophene-2-yl]-phenyl]-aminobenzoic acid) has been studied using surface-sensitive vibrational sum frequency generation(VSFG) spectroscopy. The VSFG spectra reveal the formation of poorly ordered dye layers on relatively rough surfaces where XPS measures a higher dye loading. Furthermore, these poorly ordered dye molecules are responsible for the generation of trapped electronic states as probed by successive photoluminescence (PL) measurements. Surface sensitive VSFG spectroscopy in combination with XPS and PL measurements provide complementary spectral information on ordering of the adsorbed dyes, their density on the surface and electronic states of the adsorbed monolayer which are prerequisite for improving our understanding of molecularly functionalized photoelectrodes and their further development.

True Origin of Amide I Shifts Observed in Protein Spectra Obtained with Sum Frequency Generation Spectroscopy.

Accurate determination of protein structure at interfaces is critical for understanding protein interactions, which is directly relevant to a molecular-level understanding of interfacial proteins in biology and medicine. Vibrational sum frequency generation (VSFG) spectroscopy is often used for probing the protein amide I mode, which reports protein structures at interfaces. Observed peak shifts are attributed to conformational changes and often form the foundation of hypotheses explaining protein working mechanisms. Here, we investigate structurally diverse proteins using conventional and heterodyne-detected VSFG (HD-VSFG) spectroscopy as a function of solution pH. We reveal that blue-shifts of the amide I peak observed in conventional VSFG spectra upon lowering the pH are governed by the drastic change of the nonresonant contribution. Our results highlight that connecting changes in conventional VSFG spectra to conformational changes of interfacial proteins can be arbitrary, and that HD-VSFG measurements are required to draw unambiguous conclusions about structural changes in biomolecules.

Photoactive Yellow Protein Adsorption at Hydrated Polyethyleneimine and Poly-l-Glutamic Acid Interfaces.

Chiral and achiral vibrational sum-frequency generation (VSFG) spectroscopy was performed in the 1400-1700 and 2800-3800 cm-1 range to study the interfacial structure of photoactive yellow protein (PYP) adsorbed on polyethyleneimine (PEI) and poly-l-glutamic acid (PGA) surfaces. Nanometer-thick polyelectrolyte layers served as the substrate for PYP adsorption, with 6.5-pair layers providing the most homogeneous surfaces. When the topmost material was PGA, it acquired a random coil structure with a small number of β2-fibrils. Upon adsorption on oppositely charged surfaces, PYP yielded similar achiral spectra. However, the VSFG signal intensity increased for PGA surfaces with a concomitant redshift of the chiral Cα-H and N-H stretching bands, suggesting increased adsorption for PGA compared to PEI. At low wavenumbers, both the backbone and the side chains of PYP induced drastic changes to all measured chiral and achiral VSFG spectra. Decreasing ambient humidity led to the loss of tertiary structure with a re-orientation of α-helixes, evidenced by a strongly blue-shifted chiral amide I band of the β-sheet structure with a shoulder at 1654 cm-1. Our observations indicate that chiral VSFG spectroscopy is not only capable of determining the main type of secondary structure of PYP, i.e., β-scaffold, but is also sensitive to tertiary protein structure.

The role of resonant coupling in vibrational sum-frequency-generation spectroscopy: Liquid acetonitrile at the silica interface

Vibrational sum-frequency-generation (VSFG) spectroscopy is a versatile technique for probing molecular organization at interfaces. There is a growing recognition that dynamic phenomena, such as reorientation and intermolecular vibrational coupling, can also influence VSFG spectra. The silica/liquid acetonitrile interface is a useful system for exploring these effects in more detail. The organization of acetonitrile at this interface has been well studied, and is known to resemble that of a supported lipid bilayer in many ways. Here isotopic dilution is used to explore the influence of resonant intermolecular coupling of methyl symmetric stretches on the VSFG spectroscopy of this system. VSFG spectra in the methyl stretching region at this interface show a blue shift, a decrease in linewidth, and a higher-than-expected intensity upon dilution in deuterated acetonitrile. We demonstrate that resonant coupling influences VSFG spectral shifts through the infrared transition. Using molecular simulations, we show that our experimental observations are consistent with resonant coupling between methyl transition dipoles being a significant, but not the dominant, contribution to the observed spectral shift upon isotopic dilution. Furthermore, our molecular simulations demonstrate that resonant coupling accounts partially for changes in linewidth and intensity. These classical molecular dynamics simulations also elucidate the behavior of the isotropic Raman spectrum in the bulk liquid upon isotopic dilution. We further simulate the resonant coupling among cyano stretches in this system. These simulations match the experimental shift due to the Raman non-coincidence effect shift of the CN stretch in the bulk liquid, but suggest that the corresponding resonant-coupling-induced shift in the VSFG spectrum at the silica interface is minimal. Our experimental and simulation results indicate that proximity to an interface can cause substantial changes in the resonant coupling of vibrations in a liquid.

Vibrational Sum Frequency Generation Spectra of Water-Vapor Interfaces Covered by Alcohols: Effects of Surface Coverage and Coupling between Oscillators.

The present study deals with the effects of varying coverage of water surface by alcohols on the vibrational sum frequency generation (VSFG) spectrum of interfacial water. We have considered two different alcohols: Tertiary butyl alcohol (TBA) whose alkyl part is fully branched and stearyl alcohol (STA) which has a long linear alkyl chain with larger hydrophobic surface area than that of TBA. With increase of the alcohol concentration, the hydrogen bonded OH stretch region of the VSFG spectrum is found to change following a regular trend for the STA-water system, whereas non-monotonic variation of the VSFG spectrum is observed for the TBA-water system which can be correlated with the presence of very different interactions of TBA molecules at different concentrations. On increasing the concentration of TBA, the hydrophobic groups get more tilted towards the water phase and significant hydrophobic interactions are introduced at higher concentrations. Whereas, for STA, there is a gradual increase in the hydrophilic interaction. Because of stacking interactions between the long chain alkyl groups, the hydrophobic parts stay outward from the water phase at higher concentrations and a regular change in the VSFG spectrum is observed. We have also presented a computationally efficient scheme to calculate the VSFG spectrum of interfacial systems for coupled oscillators which is expected to be beneficial for the treatment of coupling where the interfacial system size is inherently large.

Unanticipated Hydrophobicity Increases of Squalene and Human Skin Oil Films Upon Ozone Exposure.

The C-H and O-H oscillators on the surfaces of thin films of human-derived skin oil and squalene are probed under ambient conditions (300 K, 1 atm total pressure, 40% RH) using second-order vibrational spectroscopy and contact angle goniometry before and after exposure to ppb amounts of ozone. Skin oil and squalene are found to produce different vibrational sum frequency generation spectra in the C-H stretching region, while exposure to ozone results in surface spectra for both materials that is consistent with a loss of C-H oscillators. The measured contact angles show that the hydrophobicity of the films increases following exposure to ozone, consistent with the reduction in C═C···H2O ("πH") bonding interactions that is expected from C═C double bond loss due to ozonolysis and indicating that the polar functional groups formed point toward the films' interiors. Implications for heterogeneous indoor chemistry are discussed.

Tutorials in vibrational sum frequency generation spectroscopy. III. Collecting, processing, and analyzing vibrational sum frequency generation spectra.

In this Tutorial series, we aim to provide an accessible introduction to vibrational sum frequency generation (VSFG) spectroscopy, targeted toward people entering the VSFG world without a rigorous formal background in optical physics or nonlinear spectroscopy. In this article, we discuss in detail the processes of collecting and processing VSFG data, and user-friendly processing software (sfgtools) is provided for use by people new to the field. Some discussion of analyzing VSFG spectra is also given, specifically with a discussion of fitting homodyne VSFG spectra, and a discussion of what can be learned (both qualitatively and quantitatively) from VSFG spectra.

Temporal and chirp effects of laser pulses on the spectral line shape in sum-frequency generation vibrational spectroscopy.

Assignment and interpretation of the sum-frequency generation vibrational spectra (SFG-VS) depend on the ability to measure and understand the factors affecting the SFG-VS spectral line shape accurately and reliably. In the past, the formulation of the polarization selection rules for SFG-VS and the development of the sub-wavenumber high-resolution broadband SFG-VS (HR-BB-SFG-VS) have provided solutions for many of these needs. However, despite these advantages, HR-BB-SFG-VS have not been widely adopted. The majority of SFG measurements so far still relies on the picosecond (ps) scanning SFG-VS or the conventional broadband SFG-VS (BB-SFG-VS) with the spectral resolution around (mostly above) 10cm-1, which also results in less ideal spectral line shape in the SFG spectra due to the temporal and chirp effects of the laser pulses used in experiment. In this study, the temporal and the chirp effects of laser pulses with different profiles in the SFG experiment on the measured SFG-VS spectral line shape are examined through spectral simulation. In addition, the experimental data of a classical model system, i.e., octadecyltrichlorosilane monolayer on glass, obtained from the ps scanning SFG-VS, the BB-SFG-VS, and the HR-BB-SFG-VS measurements are directly compared and examined. These results show that temporal and chirp effects are often significant in the conventional BB-SFG-VS, resulting in line shape distortions and peak position shifts besides spectral broadening. Such temporal and chirp effects are less significant in the ps scanning SFG-VS. For the HR-BB-SFG-VS, spectral broadening and temporal and chirp effects are insignificant, making HR-BB-SFG-VS the choice for accurate and reliable measurement and analysis of SFG-VS.

Evidence for a Local Field Effect in Surface Plasmon-Enhanced Sum Frequency Generation Vibrational Spectra

Surface plasmon-enhanced vibrational spectroscopy has been demonstrated to be an important highly sensitive diagnostic technique, but its enhanced mechanism is yet to be explored. In this study, we couple femtosecond sum frequency generation vibrational spectroscopy (SFG-VS) with surface plasmon generated by the excitation of localized gold nanorods/nanoparticles and investigate the plasmonically enhanced factors (EFs) of SFG signals from poly(methyl methacrylate) films. Through monitoring the SFG intensity of carbonyl and ester methyl groups, we have established a correlation between EFs and the coupling of localized surface plasmon resonance with SFG and visible beams. It is found that the total enhanced factor is approximately proportional to the square of an enhanced factor of the SFG electromagnetic field and the fourth power of the enhanced factor of the visible electromagnetic field. The local field effect is roughly expressed to be the square of an enhanced factor of the visible electromagnetic field. This finding will help to guide the experimental design of plasmon-enhanced SFG to drastically improve the detection sensitivity and thus provide greater insight into the ultrafast dynamics near plasmonic surfaces.

Surfactant Adsorption to Gypsum Surfaces and the Effects on Solubility in Aqueous Solutions.

Vibrational sum frequency generation (VSFG) spectroscopy, conductometric titration measurements, and EDX elemental mapping were used to examine surfactant adsorption to the gypsum (010) surface and assess the effects of surfactant adsorption on gypsum solubility in aqueous solutions. Sodium dodecyl sulfate (SDS) and dodecyltrimethylammonium chloride (DTAC) were used as anionic and cationic surfactants, respectively. Gypsum/SDS interactions result in an ordered precipitate layer on the gypsum surface after water evaporation; gypsum/DTAC interaction did not show a similar effect, despite exposure of gypsum to equivalent amounts of surfactant. VSFG spectra showed that SDS molecules adsorb with their chains parallel to the gypsum surface; spectra from gypsum surfaces treated with DTAC, however, showed no measurable response, implying that these surfactants form disorganized aggregates with no polar ordering. Vibrational data were supported by independent EDX measurements that show a uniform distribution of SDS across the gypsum surface. In contrast, element-specific EDX images showed that DTAC clustered in tightly localized patches that left most of the gypsum surface exposed. The uniform adsorption of SDS on the gypsum surface suppresses long-term dissolution up to 40% when compared to samples exposed to DTAC. Gypsum samples in DTAC-containing solutions lose approximately the same amount of material to dissolution as samples immersed in pure water.

Comprehensive analysis on anomalous phenomenon of ethanol‐soluble poly(vinyl butyral) membrane for ethanol recovery via pervaporation

AbstractPoly(vinyl butyral) (PVB) is selected as a promising ethanol‐permselective membrane based on the solubility parameter theory; however, it exhibits anomalous water perm‐selectivity in practical pervaporation (PV) process. Comprehensive analysis based on experimental and theoretical methods were carried out to explore the inherent mechanism of the anomalous performance. Firstly, sum frequency generation vibrational spectra and contact angle were developed to quantify the surface reconstruction of membrane in air and ethanol, which indicated that hydrophilic hydroxyl tended to expose on membrane surface with ethanol thus improving the membrane affinity to water. Meanwhile, swelling behaviors proved more water would accumulate in the ethanol swollen membrane. Furthermore, theoretical analysis in terms of sorption and diffusion process, based on the UNIFAC‐FV model and Fujita free‐volume theory, confirmed the mechanism of anomalous phenomenon of PVB membrane. The comprehensive investigation was expected to provide insights into the basic separation mechanism of PV process.

Effects of stearyl alcohol monolayer on the structure, dynamics and vibrational sum frequency generation spectroscopy of interfacial water.

The structure, dynamics and vibrational spectroscopy of a water surface covered by a monolayer of stearyl alcohol (STA) are investigated by means of molecular dynamics simulations and vibrational sum frequency generation (VSFG) spectral calculations. The STA molecules possess long linear alkyl chains without any branching and have a rather large hydrophobic surface area. The STA-water interface is found to be rather narrow with an ordered outward arrangement of the alcohol chains at the water surface. The water molecules in the interfacial region which contribute most to the observed VSFG spectrum are identified. It is shown that the observed red shift in the hydrogen bonded part of the VSFG spectrum can originate from partial cancellation of the spectral responses from up and down-oriented OH moieties of interfacial water which are hydrogen bonded, respectively, to alcohol and water molecules. The effects of intra and intermolecular coupling to the VSFG spectrum are also calculated for the STA-water interface considered here. On the dynamical side, a slowing down of the hydrogen bond and orientational relaxation is found for the interfacial water. It is found that the ordered arrangement of STA molecules at the surface holds the interfacial water molecules rather tightly and slows down the dynamics. The current results of the STA-water interface are also compared with those of the tertiary butyl alcohol (TBA)-water interface where the alcohol has a fully branched hydrophobic part of the lower surface area.

Sum frequency generation vibrational spectra of perovskite nanocrystals at the single-nanocrystal and ensemble levels

Determination of molecular structures of organic-inorganic hybrid perovskite (OIHP) nanocrystals at the single-nanocrystal and ensemble levels is essential to understanding the mechanisms responsible for their size-dependent optoelectronic properties and the nanocrystal assembling process, but its detection is still a bit challenging. In this study, we demonstrate that femtosecond sum frequency generation (SFG) vibrational spectroscopy can provide a highly sensitive tool for probing the molecular structures of nanocrystals with a size comparable to the Bohr diameter (∼10 nm) at the single-nanocrystal level. The SFG signals are monitored using the spectral features of the phenyl group in (R-MBA)PbBr3 and (R-MBA)2PbI4 nanocrystals (MBA: methyl-benzyl-ammonium). It is found that the SFG spectra exhibit a strong resonant peak at 3067±3 cm−1 (ν2 mode) and a weak shoulder peak at 3045±4 cm−1 (ν7a mode) at the ensemble level, whereas a peak of the ν2 mode and a peak at 3025±3 cm−1 (ν20b mode) at the single-nanocrystal level. The nanocrystals at the single-nanocrystal level tend to lie down on the surface, but stand up as the ensemble number and the averaged sizes increase. This finding may provide valuable information on the structural origins for size-dependent photo-physical properties and photoluminescence blinking dynamics in nanocrystals.

Vibrational Sum Frequency Generation Spectroscopy of Surface Hydroxyls on Nickel Phyllosilicate Nanoscrolls.

Phyllosilicate clays are layered structures with diverse nanoscale morphology depending on the composition. Size mismatch between the sheets can cause them to form nanoscrolls, a spiral structure with different inner and outer surface charges. The hydroxyls on the exposed surface of the nanoscrolls determine the adsorption properties and hydrophilicity of the surface. Vibrational sum frequency generation (VSFG) spectroscopy was applied to study the surface hydroxyls of nickel phyllosilicate (Ni3Si2O5(OH)4), revealing three distinct in-phase OH-stretch modes: 3642, 3645, and 3653 cm-1. The relative signs of the peaks allow their assignment as "outward" and "inward" pointing hydroxyls on the opposite sides of the scrolled sheet, consistent with the crystal structure. Orientational analysis of polarization-selected VSFG spectra is consistent with a broad (140-164°) step-function distribution of the OH-stretch tilt angles, which we attribute to the uncompensated portion of the scroll rolled more than a whole number of full turns.

Wettability of graphene and interfacial water structure

<h2>Summary</h2> Understanding the wettability of graphene is important for various applications, such as water desalination, energy storage, and catalysis. However, the detailed water hydrogen-bonding structure at the water-graphene interface is not yet fully understood. Using vibrational sum-frequency-generation (VSFG) spectroscopy, we elucidate the water structure at a water-graphene interface. As the number of graphene layers increases, water molecules with dangling OH groups become more populated, indicating the transition from transparency to translucency. We compare the water contact angles on the graphene surfaces with VSFG results, showing an excellent correlation between the water adhesion energy of graphene and the fraction of dangling OH groups estimated from the VSFG spectrum. This observation suggests that the VSFG could be an incisive technique for measuring water's adhesion energy on any spatially confined interface where the water contact angle cannot be measured. We anticipate that the VSFG results will help to elucidate the wettability of low-dimensional materials. <h3>Video Abstract</h3>